Refreshed patches. The following patches were upstreamed and have been deleted:
* target/linux/ar71xx/patches-4.9/106-01-MIPS-ath79-fix-AR724X_PLL_REG_PCIE_CONFIG-offset.patch
* target/linux/generic/pending-4.9/180-net-phy-at803x-add-support-for-AT8032.patch
* target/linux/generic/pending-4.9/181-net-usb-add-lte-modem-wistron-neweb-d18q1.patch
* target/linux/generic/pending-4.9/182-net-qmi_wwan-add-BroadMobi-BM806U-2020-2033.patch
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Switch ports 0..3 are connected to external ports LAN{1..4} in sequence,
switch port 4 is not used, and switch port 5 is connected to the CPU.
The WAN port is attached to the CPU's second network interface; it has no
connection to the internal switch.
Reuse the "Dell TrueMobile 2300" entry, which describes the same mapping.
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
(cherry picked from commit 7ac238fc98)
THIN_ARCHIVES option is enabled by default in the kernel configuration
and no one target config disables it. So enable it by default and remove
this symbol from target specific configs to keep them light.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit 67a3cdcbb0)
New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols
are enabled. Both of these symbols are enabled by default in the
generic config, so enable FUTEX_PI by default too to keep platform
specific configs minimal.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit bdc2b58c4b)
OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have
OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config
of 4.14 and remove this option from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit a08b0d0c31)
DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST
which is disable by default, so disable DRM_LIB_RANDOM by default too.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit 978543a246)
These options do not used by any supported arch, so disable them by
default to make arch configs a bit more clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit ead26e9db6)
Only one arch (x86_64) enables this option. So disable
ARCH_WANTS_THP_SWAP by default and remove referencies to it from all
configs (except x86_64) to make them clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit f928c338ad)
The biggest (and the only?) disadventage of this is obviously an
increased image size.
For mips74k the size of vmlinux goes up from 4186684 B to 4701436 B.
Most devices use LZMA compressed kernel so probably more important is
vmlinux.lzma size which goes up from 1342945 B to the 1508498 B.
Still this isn't something that should stop target kernel bump. There
are various adventages of kernel 4.14. If kernel / image size is a
serious concern for anyone, it's perfectly possible to use previous
release which is pretty solid for the brcm47xx.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: Paul Wassi <p.wassi@gmx.at>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Optimize the compiler output for larger cache blast cases that are
common for DMA-based networking.
On ar71xx, I measured a routing throughput increase of ~8%
Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It's a device based on BCM5365P (0x5365 package 0x00). This SoC has
USB 1.1 controller but device has two USB 2.0 parts. They are handled by
PCI-based controllers: 1106:3038 UHCI and 1106:3104 EHCI.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The target name does not need to included a revision
if all revisions are supported.
This target supports all revisions (v1, v2, v2.1).
Signed-off-by: Moritz Warning <moritzwarning@web.de>
[Keep the version numbers in the device title, it doesn't harm]
Signed-off-by: Mathias Kresin <dev@kresin.me>
D-Link DIR-330 is clone of ASUS WL500GP2, by default conf the WAN port is
eth1, it's not working cus eth1 not soldered and wan port function
performs 5th port of the switch.
Signed-off-by: Antony Black <gtrtfm@gmail.com>
On the Asus RT-N16, the ports are not mapped the in the same way as
the RT-N12. It is, however, the same as the Linksys E3000v1.
Signed-off-by: Tim Thorpe <timfthorpe@gmail.com>
Kernel 4.9 is now working on the brcm47xx boards, we just recently fixed
the problem that some boards did not boot at all, by changing the memory
regions used to relocate the kernel to in the loader.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
By default we are reusing the stack provided by CFE, like it is intended
by CFE. On my WRT54GS it is located at 0x8043BF30, so a big kernel image
could overwrite it. Relocate it to a different memory region which is
still under the 8MB RAM, but in the higher area. We only need this
memory region for the stack of the loader, Linux will set up this
for its own.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The boot process on a WRT54GL works the following way:
1. CFE gets loaded by the boot rom from flash
2. CFE loads the loader from the flash and gzip uncompresses it
3. CFE starts the loader
4. The loader stores the FW arguments and relocates itself to
BZ_TEXT_START (now 0x80600000)
5. The loader reads the Linux image from flash
6. The loader lzma decompresses the Linux image to LOADADDR (0x80001000)
7. The loader executes the uncompress Linux image at LOADADDR
The BZ_TEXT_START was set to 0x80400000 before. When the kernel gets
uncompressed and is bigger than BZ_TEXT_START - LOADADDR it overwrote
the loader which was currently uncompressing it and made the board
crash. Increase the BZ_TEXT_START my 2 MB to have more space for the
kernel. Even on 16MB RAM devices the memory goes till 0x80FFFFFF so this
should not be a problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit 31e9445b7e.
"Linksys E1200 V1" is not a valid board name, as the brcm47xx arch code
can not detect this device. Stefan Lippers-Hollmann also found a typo in
this patch "cybetran" instead of "cybertan".
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On Asus RT-N12 and RT-N16 models, the WAN and LAN4 ports are swapped in the
initial switch configuration since the presets present in nvram appear to be
wrong.
Add special casing for these models to detect_by_model() in order to ensure
a proper switch configuration.
Fixes FS#502.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not parse /tmp/sysinfo/board_name, /proc/cpuinfo or the device tree
compatible string directly. Always use the board_name function to get
the board name.
The admswconfig package still reads /proc/cpuinfo directly. The code
looks somehow broken and the whole adm5120 which uses this package
looks unmaintained. Leave it as it is for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
I tested this on a WRT54GS and a WRT610N V1.
The WRT610N does not boot when the kernel is too big, so I deactivated KALLSYMS
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On the Linksys WRT54GSv1, the Power LED flickers in the "off" state.
Indicate status using the DMZ LED if available, since it has solid "on" and
"off" states.
This change was tested on the WRT54GSv1, but may also affect other brcm47xx
devices.
Fixes FS#793.
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
On the Linksys WRT54GSv1, the adm6996 switch driver and the
gpio_button_hotplug module both claim GPIO 6, which is connected to the
Reset button. When the switch driver's request wins, the Reset button
cannot work. This makes it impossible to enter failsafe mode without a
serial console.
Stop requesting the "adm_rc" GPIO in the switch driver, since it is not
used anywhere.
Fixes FS#792.
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
The generic preinit code is now able to setup network and switch vlan settings
from the /etc/board.json file, therefor drop the target specific code.
Fixes FS#790.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Bump kernel from 4.4.49 to 4.4.50
Compile tested: All targets
Run tested: ar71xx Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
The Asus WL-500W buttons are active high,
but the software treats them as active low.
Fix the inverted logic.
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
BCM4704 SoC has only USB 1.1 core:
ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x03, vendor 0x4243)
but this device actually comes with two USB 2.0 ports.
It appears embedded controller isn't used but instead there are two PCI
attached controllers (next to the BCM4321 wireless card):
1106:3038 VT82xx/62xx UHCI USB 1.1 Controller
1106:3104 USB 2.0
Choose a set of USB drivers which actually support this hardware.
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Prevents crashes when IRQs arrive when the current kernel stack context
already contains deeply nested function calls, e.g. when stacking lots
of network devices on top of each other
Signed-off-by: Felix Fietkau <nbd@nbd.name>
WL500GPv1 profile included ath5k which made it usable only for people
who decided to replace default BCM4318 card with Atheros one. We can't
have profile for every possible configuration. If someone adjusts hw in
such a way he can always install a proper package.
WRTSL54GS profile got extra packages for a specific USB usage. Our
standard profile provides basic USB and we should stick to this. We
can't make everyone happy by including packages for all common USB use
cases and all common filesystems.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
