A device COMPILE target should not depend on another COMPILE.
Otherwise race condition may happen.
The loader is very small. Compiling it twice shouldn't
have a huge impact.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
As described in commit 97c77fff28
MV88E6xxx driver (NET_DSA_MV88E6XXX) cannot be built-in when PTP
(PTP_1588_CLOCK) is a module in Linux 5.15. But actually it should be
allowed to be built-in when its PTP support (NET_DSA_MV88E6XXX_PTP) is
disabled.
This adds a patch to fix that.
Signed-off-by: Johnny S. Lee <foss@jsl.io>
General specification:
- SoC Type: MediaTek MT7620N (580MHz)
- ROM: 8 MB SPI-NOR (W25Q64FV)
- RAM: 64 MB DDR (M13S5121632A)
- Switch: MediaTek MT7530
- Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
- Wireless 2.4 GHz: b/g/n
- Buttons: 1 button (RESET)
- Bootloader: U-Boot 1.1.3, MediaTek U-Boot: 5.0.0.5
- Power: 12 VDC, 1.0 A
Flash by the native uploader in 2 stages:
1. Use the native uploader to flash an initramfs image. Choose
openwrt-ramips-mt7620-snr_cpe-w4n-mt-initramfs-kernel.bin file by
"Administration/Management/Firmware update/Choose File" in vendor's
web interface (ip: 192.168.1.10, login: Admin, password: Admin).
Wait ~160 seconds.
2. Flash a sysupgrade image via the initramfs image. Choose
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
file by "System/Backup/Flash Firmware/Flash image..." in
LuCI web interface (ip: 192.168.1.1, login: root, no password).
Wait ~240 seconds.
Flash by U-Boot TFTP method:
1. Configure your PC with IP 192.168.1.131
2. Set up TFTP server and put the
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
image on your PC
3. Connect serial port (57600 8N1) and turn on the router.
Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2:
Load system code then write to Flash via TFTP.").
Press Y key when show "Warning!! Erase Linux in Flash then burn
new one. Are you sure? (Y/N)"
Input device IP (192.168.1.1) ==:192.168.1.1
Input server IP (192.168.1.131) ==:192.168.1.131
Input Linux Kernel filename () ==:
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
3. Wait ~120 seconds to complete flashing
Signed-off-by: Alexey Bartenev <41exey@proton.me>
KuWFi C910 is an 802.11n (300N) indoor router with LTE support.
I can't find anywhere the OEM firmware. So if you want to restore the
original firmware you must do a dump before the OpenWrt flash.
According to the U-Boot, the board name is Iyunlink MINI_V2.
Hardware
--------
SoC: Qualcomm QCA9533 650/400/200/25/25 MHz (CPU/RAM/AHB/SPI/REF)
RAM: 128 MB DDR2 16-bit CL3-4-4-10 (Nanya NT5TU64M16HG-AC)
FLASH: 16 MB Winbond W25Q128
ETH:
- 2x 100M LAN (QCA9533 internal AR8229 switch, eth0)
- 1x 100M WAN (QCA9533 internal PHY, eth1)
WIFI:
- 2.4GHz: 1x QCA9533 2T2R (b/g/n)
- 2 external non detachable antennas (near the power barrel side)
LTE:
- Quectel EC200T-EU (or -CN or -AU depending on markets)
- 2 external non detachable antennas (near the sim slot side)
BTN:
- 1x Reset button
LEDS:
- 5x White leds (Power, Wifi, Wan, Lan1, Lan2)
- 1x RGB led (Internet)
UART: 115200-8-N-1 (Starting from lan ports in order: GND, RX, TX, VCC)
Everything works correctly.
MAC Addresses
-------------
LAN XX:XX:XX:XX:XX:48 (art@0x1002)
WAN XX:XX:XX:XX:XX:49 (art@0x1002 + 1)
WIFI XX:XX:XX:XX:XX:48
LABEL XX:XX:XX:XX:XX:48
Installation
------------
Turn the router on while pressing the reset button for 4 seconds.
You can simply count the flashes of the first lan led. (See notes)
If done correctly you should see the first lan led glowing slowly and
you should be able to enter the U-Boot web interface.
Click on the second tab ("固件") and select the -factory.bin firmware
then click "Update firmware".
A screen "Update in progress" should appear.
After few minutes the flash should be completed.
This procedure can be used also to recover the router in case of soft
brick.
Backup the original firmware
----------------------------
The following steps are intended for a linux pc. However using the
right software this guide should also work for Windows and MacOS.
1) Install a tftp server on your pc. For example tftpd-hpa.
2) Create two empty files in your tftp folder called:
kuwfi_c910_all_nor.bin
kuwfi_c910_firmware_only.bin
3) Give global write permissions to these files:
chmod 666 kuwfi_c910_all_nor.bin
chmod 666 kuwfi_c910_firmware_only.bin
4) Start a netcat session on your pc with this command:
nc -u -p 6666 192.168.1.1 6666
5) Set the static address on your pc: 192.168.1.2. Connect the router
to your pc.
6) Turn the router on while pressing the reset button for 8-9 seconds.
You can simply count the flashes of the first lan led. If you
press the reset button for too many seconds it will continue
the normal boot, so you have to restart the router. (See notes)
7) If done correctly you should see the U-Boot network console and you
should see the following lines on the netcat session:
Version and build date:
U-Boot 1.1.4-55f1bca8-dirty, 2020-05-07
Modification by:
Piotr Dymacz <piotr@dymacz.pl>
https://github.com/pepe2k/u-boot_mod
u-boot>
8) Start the transfer of the whole NOR:
tftpput 0x9f000000 0x1000000 kuwfi_c910_all_nor.bin
9) The router should start the transfer and it should end with a
message like this (pay attention to the bytes transferred):
TFTP transfer complete!
Bytes transferred: 16777216 (0x1000000)
10) Repeat the same transfer for the firmware:
tftpput 0x9f050000 0xfa0000 kuwfi_c910_firmware_only.bin
11) The router should start the transfer and it should end with a
message like this (pay attention to the bytes transferred):
TFTP transfer complete!
Bytes transferred: 16384000 (0xfa0000)
12) Now you have the backup for the whole nor and for the firmware
partition. If you want to restore the OEM firmware from OpenWrt
you have to flash the kuwfi_c910_firmware_only.bin from the
U-Boot web interface.
WARNING: Don't use the kuwfi_c910_all_nor.bin file. This file
is only useful if you manage to hard brick the router or you
damage the art partition (ask on the forum)
Notes
-----
This router (or at least my unit) has the pepe2k's U-Boot. It's a
modded U-Boot version with a lot of cool features. You can read more
here: https://github.com/pepe2k/u-boot_mod
With this version of U-Boot, pushing the reset button while turning on
the router starts different tools:
- 3-5 seconds: U-Boot web interface that can be used to replace the
firmware, the art or the U-Boot itself
- 5-7 seconds: U-Boot uart console
- 7-10 seconds: U-Boot network console
- 11+ seconds: Normal boot
The LTE modem can be used in cdc_ether (ECM) or RNDIS mode.
The default mode is ECM and in this commit only the ECM software is
included. In order to set RNDIS mode you must use this AT command:
AT+QCFG="usbnet",3
In order to use again the ECM mode you must use this AT command:
AT+QCFG="usbnet",1
Look for "Quectel_EC200T_Linux_USB_Driver_User_Guide_V1.0.pdf" for
other AT commands
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
1. Use ARTIFACTS to build factory image. This change allows users to
generate initramfs factory image using OpenWrt ImageBuilder.
2. Override the default bootargs property defined in "mt7621.dtsi".
Although we use the "bootargs-override" property to set bootargs,
the default "bootargs" property will still be written into the
device tree, so it is better to override it.
Tested on SIM SIMAX1800T
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
1. Explicitly declare gpio pin groups to ensure that gpio works properly.
2. Override bootargs in device tree to avoid modifying u-boot envs during
initial installation.
Tested on H3C TX1801 Plus
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The compatible in the device tree is "haoyu,a10-marsboard",
modify the board_name to keep it consistent.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The kmod prefix for sound-soc-sunxi is missing, fix it.
Also add kmod-sound-core as dependence.
Fixes: 6a35659 ("sunxi: Added profile for HAOYU Electronics Marsboard A10")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
While working on it remove stale uboot partition label and merge art
into partition node.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Merge art into partition node.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Merge art into partition node.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Merge art into partition node.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Merge art into partition node.
Signed-off-by: Nick Hainke <vincent@systemli.org>
'cs-gpios = <0>, <0>' is a hack in ath79 to override the incorrectly
specified maximum number of chipselects available in spi-ath79.c.
It's not needed here and must have been copied here by mistake.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
In this implementation, the flash partition layout is adjusted to avoid
modifying the uboot environment of mtdparts. This ensures that the 30M
ubi_kernel partition remains aligned with the stock ubi partition, and
the kernel volume is placed in it. This allows the stock uboot to boot
from it without changing the mtdparts, which is useful for reverting back
to the stock firmware using Xiaomi Firmware Tools. In actual testing,
modifying mtdparts has been found to break Xiaomi Firmware Tools.
1. use ARTIFACTS to generate initramfs-factory.ubi for easy installation.
2. The NAND flash layout is changed to allow for reverting back to the
stock firmware.
3. Before performing sysupgrade, do some cleanup in platform_pre_upgrade
to ensure a clean installation of OpenWRT.
4. Setup the uboot env to ensure that the system always boot, which can
be helpful for users who may forget to do this before sysupgrade in
the initramfs.
New flash instructions:
1. Gain ssh access. Please refer to:
https://openwrt.org/toh/xiaomi/redmi_ax6000#installation)
2. Check which system current u-boot is loading from:
COMMAND: `cat /proc/cmdline`
sample OUTPUT: `console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1`
if firmware=1, current system is ubi1
if firmware=0, current system is ubi0
3. Setup nvram and write the firmware:
If the current system is ubi1, please set it up so that the next time
it will boot from ubi, and write the firmware to ubi:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=0
nvram set flag_last_success=0
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd8 -y -f /tmp/initramfs-factory.ubi
```
If the current system is ubi, please set it up so that the next time
it will boot from ubi1, and write the firmware to ubi1:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=1
nvram set flag_last_success=1
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd9 -y -f /tmp/initramfs-factory.ubi
```
4. After rebooting, the system should now boot into the openwrt initramfs.
Flash the squashfs-sysupgrade.bin via using ssh or luci.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Done.
For existing users of the Redmi AX6000 running OpenWrt, here are the steps to
switch to this new layout:
1. Flash initramfs-factory.ubi
```
mtd -r -e ubi write /tmp/initramfs-factory.ubi ubi
```
2. After rebooting, the system will boot into the new openwrt-initramfs.
Log in and perform a sysupgrade to complete the process.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Add support for EON EN25QX128A spi nor flash with no flags as it does
support SFDP parsing.
Fixes: #9442
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Tested-by: Szabolcs Hubai <szab.hu@gmail.com> [ramips/mt7621: xiaomi_mi-router-4a-gigabit]
add DT nodes and default package for the LEDs on Redmi AX6000
Signed-off-by: Furong Xu <xfr@outlook.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Without explicitly enabling sel_clk, clk_disable_unused() will disable
it when boot is done, causing CPU hang on SPI1 register access on MT7986.
Explicitly enable sel_clk to make SPI1 functional.
Signed-off-by: Furong Xu <xfr@outlook.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
- rtl83xx_vlan_filtering()
"struct switchdev_trans *trans" parameter was removed[1] and
"struct netlink_ext_ack *extack" was added[2].
[1]: https://www.spinics.net/lists/netdev/msg712250.html
[2]: https://www.spinics.net/lists/netdev/msg722496.html
- rtl83xx_vlan_add/del()
vlan->vid_begin and vlan->vid_end were removed and vlan->vid was
added[3].
[3]: https://www.spinics.net/lists/netdev/msg712248.html
- rtl83xx_vlan_prepare()
"port_vlan_prepare" member was removed from "dsa_switch_ops" struct
in dsa.h[4] and vlan_prepare function should be called from vlan_add
function. Also, change return type of vlan_add function to int.
[4]: https://www.spinics.net/lists/netdev/msg712252.html
- rtl83xx_port_mdb_add()
"port_mdb_prepare" member in "dsa_switch_ops" struct was removed and
preparation need to be done in the function of "port_mdb_add" member
instead. And also, int type need to be returned on "port_mdb_add"
member[5].
[5]: https://www.spinics.net/lists/netdev/msg712251.html
- rtl83xx_port_pre_bridge_flags(), rtl83xx_port_bridge_flags()
The current "port_pre_bridge_flags" member and "port_bridge_flags"
member in "dsa_switch_ops" in dsa.h has flags of
"struct switchdev_brport_flags" type instead[6], so adjust to it.
And, the changed features are passed by flags.mask[7] in
rtl83xx_port_bridge_flags(), so check it before calling function
to enable/disable fieature.
[6]: https://lore.kernel.org/lkml/20210212151600.3357121-7-olteanv@gmail.com/
[7]: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e18f4c18ab5b0dd47caaf8377c2e36d66f632a8c
Suggested-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[shorten final return statement of rtl83xx_port_mdb_add()]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
- 007-5.16-gpio-realtek...: upstreamed on 5.16 and backported to 5.15.3
- 708-brflood-spi.patch : upstreamed
- 709-lag-offloading.patch: upstreamed
- 713-v5.12-net-dsa-... : upstreamed and some implementations are
replaced
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The following drivers were upstreamed and available on 5.15, so drop
from OpenWrt tree.
- realtek-otto-gpio (5.13)
- realtek-rtl-spi (5.12)
- realtek-rtl-intc (5.12)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|109.3-19: Warning (reg_format): macaddr@0:reg:property has invalid length (8 bytes)
|113.3-24: Warning (reg_format): calibration@1000:reg: property has invalid length (8 bytes)
|117.3-24: Warning (reg_format): calibration@5000:reg: property has invalid length (8 bytes)
also integrate the art-nodes nodes back into the partition-subnode
and change the calibration labels to match what everyone else is
doing.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|109.3-19: Warning (reg_format): macaddr@0:reg:property has invalid length (8 bytes)
|113.3-24: Warning (reg_format): calibration@1000:reg: property has invalid length (8 bytes)
|117.3-24: Warning (reg_format): calibration@5000:reg: property has invalid length (8 bytes)
also integrate the art-nodes nodes back into the partition-subnode
and change the calibration labels to match what everyone else is
doing.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(removed mtd-cal-data property, merged art + addr nodes back into
partition)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(merged art node back into partition-node)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(merged art into partition node, removed stale uboot label)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Remove the caldata extraction in userspace. The board already uses
nvmem-cells since
commit e354b01baf ("ath79: calibrate all ar9344 tl-WDRxxxx with nvmem")
Signed-off-by: Nick Hainke <vincent@systemli.org>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(merged art-node back into partition-node)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Some carrier boards [1][2] for the Raspberry Pi CM4 that are specifically
designed to be used as routers come with secondary NICs using a Realtek
RTL8111 Gigabit Ethernet chip.
When using such a board as a router with OpenWrt, it is very helpful
when both NICs are working by default. Since the Raspberry Pi 4 and the
CM4 have plenty of disk space, it should cause no harm to include the
kmod-r8169.
[1] https://wiki.dfrobot.com/Compute_Module_4_IoT_Router_Board_Mini_SKU_DFR0767
[2] https://www.waveshare.com/wiki/CM4-DUAL-ETH-MINI
Signed-off-by: Johannes Heimansberg <git@jhe.dedyn.io>
(r8169 should pull in the necessary dependencies.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
A backported patch to the BCMA driver necessary to support the
DWL-8610AP and DIR-890L. Patch will be in upstream v6.2.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Kernel 5.10.158 added a prompt for the FUNCTION_ERROR_INJECTION symbol.
This is exposed in builds with CONFIG_KERNEL_KPROBES enabled, causing
those builds to fail due to a missing symbol. Add the symbol to fix
this.
Fixes: 6801c460b6 ("kernel: bump 5.10 to 5.10.158")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Kernel 5.15.82 added a prompt for the FUNCTION_ERROR_INJECTION symbol.
This is exposed in builds with CONFIG_KERNEL_KPROBES enabled, causing
those builds to fail due to a missing symbol. Add the symbol to fix
this.
Fixes: 68426e54ed ("kernel: bump 5.15 to 5.15.82")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The testing kernel has been running fine for months on a rather complex
network setup, with one exception being a crash in
__xfrm_state_delete(). This crash has been fixed in kernel 5.15.82, so
let's switch the qoriq target to kernel 5.15 by default.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Compex WPQ864 contains a non standard partition table. Each partition
node should be named partition and should contain a valid reg.
Fix an extra "-" present after the reg for SBL2_1 partition.
Also add "0:" to each qcom default partition following smem naming.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The refreshed patch actually use the format of <start size start size>
instead of <start end start end>. This cause boot fail since the rootfs
can't be mounted with these wrong values.
Fix it to the correct format in each affected dts.
Fixes: #11498
Fixes: 6134ba4a34 ("ipq806x: 5.15: add boot-partitions binding to fix block warning")
Tested-by: Matt Buczko <mbuczko@hotmail.com> # Askey RT4230W
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
TP-Link CPE605-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
- 560/450/225 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of DDR2 RAM
- 8 MB of SPI-NOR Flash
- 23dBi high-gain directional antenna and a dedicated metal reflector
- Power, LAN, WLAN5G green LEDs
- 3x green RSSI LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
