Now that omnia-eeprom is marked nonshared building the cortex-a9 mvebu
subtarget will fail with:
ERROR: unable to select packages:
omnia-eeprom (no such package):
required by: world[omnia-eeprom]
This is because omnia-eeprom depends on TARGET_mvebu_cortexa9_DEVICE_cznic_turris-omnia
which will not be satisfied in buildbots since CONFIG_TARGET_ALL_PROFILES
and CONFIG_TARGET_PER_DEVICE_ROOTFS are set in which case
CONFIG_TARGET_mvebu_cortexa9_DEVICE_cznic_turris-omnia is not set.
So, lets simply depend on the mvebu/cortex-a9 subtarget.
Fixes: 371e7bef40 ("omnia-eeprom: Mark it nonshared")
Link: https://github.com/openwrt/openwrt/pull/17007
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 90de3b277b)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
CONFIG_FB_INTEL is now visible on x86 since i915 driver is packaged as kmod
now and it stops compilation, so add it to the generic config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 57daea682e)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The config_get_bool also works with on/off, yes/no, true/false.
Add 'main' section name. This will make it easier to change settings from uci.
Add a link to documentation.
Signed-off-by: Sergey Ponomarev <stokito@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15579
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 4511fa4b30)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This tool was build in the phase 2 build, there the
TARGET_mvebu_cortexa9_DEVICE_cznic_turris-omnia dependecy was probably
not meat. Mark it as non shared to build it together with the target
where this option is set.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/16975
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 371e7bef40)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
All ipq807x devices that were using the legacy 'mmc_do_upgrade' eMMC
sysupgrade code were ported to the replacement 'emmc_do_upgrade' code.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 491121288e)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Note that the old ad-hoc method did not explicitly align backup data
to 64 KiB boundaries.
Also note that the qnap 301w has a 'rootfs_data' partition in the eMMC
that is being ignored by fstools during boot, presumably due to a bug.
This is why the partition is also ignored in the sysupgrade code and
there is no definition of CI_DATAPART="rootfs_data".
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit fe481c9c47)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
On aarch64 musl gcc 14.x compiler, trying compiling elfutils 0.192 with
lto option enabled will cause null-dereference error.
Example error message:
...
elf_compress.c: In function 'elf_compress':
elf_compress.c:675:26: error: potential null pointer dereference [-Werror=null-dereference]
675 | shdr->sh_flags |= SHF_COMPRESSED;
| ^
elf_compress_gnu.c: In function 'elf_compress_gnu':
elf_compress_gnu.c:127:25: error: potential null pointer dereference [-Werror=null-dereference]
127 | shdr->sh_size = new_size;
| ^ ^
...
This is a false postive warning but will abort compilation if gcc has
`-Werror` flag. This commit add a patch for this, see the bugzilla
report below.
This commit backports a series of patches to fix some errors.
Add patch:
- 007-add-libeu-symbols-to-libelf.patch
- 008-fix-autoconf-ENABLE_IMA_VERIFICATION.patch
- 009-fix-null-dereference-with-lto.patch
Link: https://sourceware.org/bugzilla/show_bug.cgi?id=32311
Signed-off-by: Ryan Keane <the.ra2.ifv@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16886
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit afffcd09e5)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since the start of the Realtek target OpenWrt works with RTL83XX as the
target architecture. Upstream is using MACH_REALTEK_RTL instead. To
simplify further development align that.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16963
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 65964c42f8)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Currently, libreadline only installs
```
/usr/lib/libhistory.so.8 -> libhistory.so.8.2
/usr/lib/libhistory.so.8.2
/usr/lib/libreadline.so.8 -> libreadline.so.8.2
/usr/lib/libreadline.so.8.2
```
But there is no `libreadline.so` or `libhistory.so` available.
So this happens:
```
root@OpenWRT:~# cat a.c
int main() {
}
root@OpenWRT:~# gcc a.c -lreadline
/usr/bin/ld: cannot find -lreadline: No such file or directory
collect2: error: ld returned 1 exit status
```
Unless, of course, one uses `-l:libreadline.so.8`... But that
doesn't help with binaries that try to dynamically open
`libreadline.so`. I have one of those here (the STklos Scheme
compiler -- I didn't make a PR for it because it's far from
being ready, but one issue is that it does use dlopen to use
readline...)
With the symlink, it works:
```
root@OpenWRT:~# ln -s /usr/lib/libreadline.so.8 /usr/lib/libreadline.so
root@OpenWRT:~#
root@OpenWRT:~# gcc a.c -lreadline
root@OpenWRT:~#
```
Another example: when trying to package rlwrap, the build failed
complaining it could not find readline (using `-lreadline`).
It would then be necessary to change rlwrap's `configure.ac`
(and also in all packages that use readline), but it seems
simpler to add the symlinks...
This PR changes the Makefile so it will include the links.
Signed-off-by: Jeronimo Pellegrini <j_p@aleph0.info>
Link: https://github.com/openwrt/openwrt/pull/16445
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 0000ba6ab8)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit fixes and closes#16313.
Switch the x86 kernel's timer to tickless operation which is
more power efficient since it is not woken up by periodic timer
interrupts when idle. Also add several other options for CPU
idle governors particularly the upstream default for tickless
kernels, CONFIG_CPU_IDLE_GOV_MENU. Without this commit, my AMD
Ryzen 7 5800U can only achieve a minimum core frequency of 1,384
MHz which is over 3x higher than the processor's minimum
frequency of 400 MHz which is accessible with this modification.
In addition to the lower clock rate, I have seen a concomitant
reduction in both idle temps and at-the-wall power consumption.
Summary:
* Idle CPU freqs dropped from 1,384 MHz to 400 Mhz.
* Idle power consumption dropped from 7 W avg to 5 W.
* Idle temps have dropped from 50C on avg to 43C.
There are other well known reasons to switch to a tickless
timer including: reduced interrupt overhead, better use of CPU
resources, and reduced latency to name a few.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16317
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 31111680f6)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The ppp package can support all features since Linux 4.7.0 kernel.
Therefore, most kernel version checks can pass unconditionally on
OpenWrt v18.06 and later version. This patch can reduce the size
of ppp package by approximately 2.5 KB.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16695
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3dbe730080)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
These permissions are not needed. Systemd also mounts these file systems
without these permissions on other Linux distributions.
Dropping these permissions should make the system more secure.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/16960
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit b88d51898d)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Create the folder /run and /run/lock using symlinks. Other Linux
distributions also have these folders and some applications might already
depend on them. Just create symlinks pointing to the older folder.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/16961
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3b710375dd)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
i915 driver requires to load correct firmware to work on latest x86
GPU, it is more reasonable to make it as a kernel module, so that
initramfs is not required, and it can also save some space from the
kernel image comparing being a built-in driver
Signed-off-by: Joe Zheng <joe.zheng@intel.com>
Link: https://github.com/openwrt/openwrt/pull/16276
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 77cfe8fd15)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Change the package name from intel-igpu-firmware-* to i915-firmware-*,
the prefix "intel-igpu" is misleading, i915 firmware is not only for
iGPU but also for dGPU now.
Remove the redundant "intel" as i915 is already well known.
More accurate file classification to handle following files correctly:
adlp_dmc.bin
mtl_huc.bin
mtl_huc_gsc.bin
mtl_gsc_1.bin
The pattern in regex is "([[:alnum:]]+)_([[:alnum:]]+)(_[\w-.]+)?\.bin",
where $1 is the platform, $2 is the firmware type (dmc, guc, huc, etc.),
and the optional $3 which is revision or other suffix.
Glob first to narrow down the target file set, and then split with "_"
to extract the firmware type (remove the ".bin" in case there is no $3)
Add package "i915-firmware" as a meta package to install all the i915
firmwares, it is a balance between simplicity and optimization.
* Installing all the available firmwares as a whole, can support all the
platforms, not only the current one but also the future ones. The
price to pay is the increased size.
* If we want to minimize the storage, we can customize to install the
necessary ones only, even for the target platform only (e.g. ADL) and
skip the others. The price to pay is the time to tune.
What I am going to do is:
* Let drm-i915 driver depend on i915-firmware-dmc, which is small and
can cover most of the old platforms
* Let the user select i915-firmware to install all the i915 firmwares as
a whole to cover the latest or future platforms
Signed-off-by: Joe Zheng <joe.zheng@intel.com>
Link: https://github.com/openwrt/openwrt/pull/16276
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit ca00bafd7e)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add a new utility, `omnia-eeprom`, which can be used to print / set
EEPROM fields on Turris Omnia.
One example when this utility might be useful is if the board
experiences random crashes due to newer versions of the DDR training
algorithm in newer U-Boot. The user can change the DDR speed from 1600K
to 1333H to solve these issues, with
```
omnia-eeprom set ddr_speed 1333H
```
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/16264
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 749a43325b)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The GatoNetworks GDSP is a re-branded version of the R5000 5G Industrial
router from Yinghua Technologies.
The re-branded device comes with OpenWrt preinstalled, and an OpenWrt-based
U-Boot bootloader version. While the flash layout has been kept compatible
with the OpenWrt version found on the stock device (see [5]), the image format
changed, making a bootloader upgrade necessary.
Specifications:
SoC: Mediatek MT7981BA
RAM: 256MB
Flash: SPI-NOR 32 MiB (Winbond W25Q256)
WLAN: MT7976CN DBDC AX Wi-Fi
Switch: MT7531AE (4x LAN Gigabit ports, 1x WAN Gigabit port)
5G: Quectel RM520N modem
Watchdog: an external WDT connected to GPIO 6 is present and always running;
the built-in Mediatek watchdog is also present and effective, but
not used at the moment.
This porting has been tested only with 1x 5G modems installed (the device
supports up to two).
Installation:
Installation is possible via sysupgrade both in the stock device and
re-branded version. However, in the former case, updating the bootloader is
required.
OpenWrt-based U-Boot Bootloader installation
--------------------------------------------
The firmware flashed in the re-branded device at manifacturing time will
flash an OpenWrt-based U-Boot bootloader with some extra recovery features
(see [1]) at first boot.
To update the bootloader, you need to install the mtd-rw module and
insmod it:
insmod mtd-rw i_want_a_brick=1
Then update relevant flash partitions:
mtd erase u-boot-env
mtd erase BL2
mtd erase FIP
mtd write openwrt-mediatek-filogic-gatonetworks_gdsp-preloader.bin BL2
mtd write openwrt-mediatek-filogic-gatonetworks_gdsp-bl31-uboot.fip FIP
And reboot, making sure all previous commands ran succesfully.
If something goes wrong, you can recover your device via the mtk_uartboot
tool.
In my testing, it was possible to start the process even without (un)-plugging
the device, may be handy for remote recovery.
Installation from stock device and firmware
-------------------------------------------
To install vanilla OpenWrt in the stock device (R5000 5G Industrial router
from Yinghua Technologies) running the stock vendor firmware, you will need
to update your bootloader as described in previous section. Remember to use
-F (force upgrade) and -n (not keeping settings).
U-Boot Recovery
---------------
This procedure has been tested only with the OpenWrt-based U-boot bootloader.
Assign your system static IP address 192.168.1.1 and start a TFTP server. The
device will look for an initramfs image named
openwrt-mediatek-filogic-gatonetworks_gdsp-initramfs-kernel.bin
(so you may use openwrt/bin/targets/mediatek/filogic as root dir for your
TFTP server).
Power on the device while keeping the reset button pressed, until you see
a TFTP request from 192.168.1.10. Your environment will be restored to it's
default state.
MAC addresses assignment
------------------------
MAC addresses are assigned slightly differently than in stock firmware. In
particular, the 5 GHz Wi-Fi uses 2.4 GHZ MAC + 1, rather than reusing it with
LA bit set as done in stock firmware. This MAC address is allocated to the
device, so it can be used.
The 2.4 GHz Wi-Fi MAC address is the label MAC. LAN MAC is used to set the
special U-Boot environment ethaddr variable.
device MAC address U-Boot env variable factory partition offset
2.4 GHz Wi-Fi :84 wifi_mac 0x4
5.8 GHz Wi-Fi :85 not present not present
WAN :86 wan_mac 0x24
LAN :87 lan_mac 0x2A
Notes
-----
[1]: the OpenWrt-based U-Boot bootloader you will find installed in the
re-branded device is configured to request for the initramfs image via
TFTP for $gdsp_tftp_tries times before trying normal boot from NOR flash.
Setting this U-Boot environment variable to 0x0 will disable the feature,
which is not implemented in this patch.
[2]: the exposed UART port is connected to ttyS1; the ttyS0 console port is
not exposed.
[3]: the provided bootloader environment has no provision for operating on
BL2 and the FIP partitions. This is an intentional choice to make it
(slightly) more difficult to brick the device.
[4]: it seems GPIO 6 is used both for the "SYS" LED and external WDT.
[5] BL2 expects to find FIP payload at a fixed offset, so some constraints
apply.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
(cherry picked from commit b43194e041)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This configuration should work with both stock and OpenWrt-based U-Boot.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
(cherry picked from commit 785ebf2baf)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The GatoNetworks GDSP is a re-branded version of the R5000 5G Industrial
router from Yinghua Technologies.
Advantages over stock bootloader:
1. supports serving the external GPIO WDT, allowing for easier work in U-Boot
shell
2. supports cool features like netconsole, easy recovery, scripting and so on
3. allows using FIT image and image integrity validation
and ultimately gives you much more flexibility to implement your tweaks.
Known issues
------------
To make it easier to operate the device, console I/O multiplexing support has
been enabled in U-Boot configuration. Setting I/O related U-Boot environment
variables to something like "serial,nc" will have the desired effect. Still,
setting these variables to such a value in the persistent environment will
lead to a crash and make it impossible to boot the system or recover it. I
decided to leave it on anyway since I think it can be very practical in
development.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
(cherry picked from commit 7f2c7b3238)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fixes following shellcheck's recommendations:
In scripts/download-check-artifact.sh line 24:
exit $1
^-- SC2086 (info): Double quote to prevent globbing and word splitting.
In scripts/download-check-artifact.sh line 53:
local sum="$(shasum -a 256 "$image_file")";
^-^ SC2155 (warning): Declare and assign separately to avoid masking return values.
In scripts/download-check-artifact.sh line 72:
cd "/tmp/verify.$$"
^-----------------^ SC2164 (warning): Use 'cd ... || exit' or 'cd ... || return' in case cd fails.
In scripts/download-check-artifact.sh line 114:
printf "Keyserver to use? [$keyserver_url] > "
^-- SC2059 (info): Don't use variables in the printf format string. Use printf '..%s..' "$foo".
In scripts/download-check-artifact.sh line 115:
read url; case "${url:-$keyserver_url}" in
^--^ SC2162 (info): read without -r will mangle backslashes.
While at it make it clear, that it is possible to download/check any
build artifacts like even SDK or ImageBuilder.
Link: https://github.com/openwrt/openwrt/pull/16871
(cherry picked from commit 27c2c140b1)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
While checking wiki documentation about GPG signatures checking I found
this nice script and I've thought, that it would be nice to provide it
officially instead of some random internet site.
Usage example:
$ ./scripts/download-check-artifact.sh https://downloads.openwrt.org/snapshots/targets/mediatek/filogic/openwrt-mediatek-filogic-openwrt_one-squashfs-sysupgrade.itb
1) Downloading image file
=========================
########################################### 100.0%
2) Downloading checksum file
============================
########################################### 100.0%
3) Downloading the GPG signature
================================
########################################### 100.0%
4) Verifying GPG signature
==========================
gpg: Signature made Tue 05 Nov 2024 05:21:50 PM UTC
gpg: using EDDSA key 92C561DE55AE6552F3C736B82B0151090606D1D9
gpg: Good signature from "OpenWrt Build System (Nitrokey3) <contact@openwrt.org>" [ultimate]
Primary key fingerprint: 8A8B C12F 46B8 36C0 F9CD B36F 1D53 D187 7742 E911
Subkey fingerprint: 92C5 61DE 55AE 6552 F3C7 36B8 2B01 5109 0606 D1D9
5) Verifying SHA256 checksum
============================
openwrt-mediatek-filogic-openwrt_one-squashfs-sysupgrade.itb: OK
Verification done!
==================
Downloaded artifact placed in '/var/home/ynezz/dev/openwrt/openwrt.git/openwrt-mediatek-filogic-openwrt_one-squashfs-sysupgrade.itb'
Cleaning up.
Adding file in a state as downloaded from https://www.abitare.org/bin/download.sh
References: https://openwrt.org/docs/guide-quick-start/verify_firmware_checksum?s[]=gpg#linux
Signed-off-by: David S. H. Rosenthal <dshr@abitare.org>
Link: https://github.com/openwrt/openwrt/pull/16871
(cherry picked from commit 4c9031fda2)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add comments to build system makefile functions and variables to help
developers in understanding build system internals and ease the
development process.
This patch adds some documentation examples with proposed doxygen-like
syntax. Hopefully, this would start the discussion and result in
generation of the makefile documentation guidelines.
Signed-off-by: Sergey Matsievskiy <matsievskiysv@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16888
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a72c8c7705)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Most links and info on the org page are broken or defunct, and all new
versions are available on the github based repo anyway.
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16910
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit ce0b843ac7)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
i2c_add_numbered_adapter is the wrong function to use here. It requires
setting nr to some value, otherwise it behaves the same as
i2c_add_adapter. nr is not set.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16825
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 44824f0b78)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
What seems to be happening is that the kernel requests an ACTIVE_LOW
gpio initially and sets it to high later based on gpios in dts.
This seems to break some devices where the bootloader sets it to high.
Fixes: e612900ae0 ("ramips: mt7621: convert usb power to regulators")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16877
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a7bc6bf7db)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Edgerouter-X factory images have not built automatically since 19.x due
to images being over 3MB. While it was possible to build custom images
with very stripped down config, this is no longer possible with the size
increases of linux 6.1 and 6.6.
Drop code for generation of factory images, if some dev later wishes to
try custom images they can revert this commit.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 4d90b79704)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
With the new layout providing 6MB for kernel there will be no issues
with kernel size affecting build of images.
Re-enable image builds for Edgerouter-X and X-SFP.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 71b4842e3b)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Use compat version to indicate that the new layout for larger kernels
is in place. This handled by the patch to ubnt.sh to always select
the kernel1 slot for flashing and as active kernel slot.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 1bdbd511b2)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
With the updated partition layout set in dts, set the KERNEL_SIZE
parameter to 6MB allowing builds of Linux 6.1 and later to fit.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 09a6bffb6e)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
