P&W R619AC is a IPQ4019 Dual-Band AC1200 router.
It is made by P&W (p2w-tech.com) known as P&W R619AC
but marketed and sold more popularly as G-DOCK 2.0.
Specification:
* SOC: Qualcomm Atheros IPQ4019 (717 MHz)
* RAM: 512 MiB
* Flash: 16 MiB (NOR) + 128 MiB (NAND)
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN)
* Wireless:
- 2.4 GHz b/g/n Qualcomm Atheros IPQ4019
- 5 GHz a/n/ac Qualcomm Atheros IPQ4019
* USB: 1 x USB 3.0
* LED: 4 x LAN, 1 x WAN, 2 x WiFi, 1 x Power (All Blue LED)
* Input: 1 x reset
* 1 x MicroSD card slot
* Serial console: 115200bps, pinheader J2 on PCB
* Power: DC 12V 2A
* 1 x Unpopulated mPCIe Slot (see below how to connect it)
* 1 x Unpopulated Sim Card Slot
Installation:
1. Access to tty console via UART serial
2. Enter failsafe mode and mount rootfs
<https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset>
3. Edit inittab to enable shell on tty console
`sed -i 's/#ttyM/ttyM/' /etc/inittab`
4. Reboot and upload `-nand-factory.bin` to the router (using wget)
5. Use `sysupgrade` command to install
Another installation method is to hijack the upgrade server domain
of stock firmware, because it's using insecure http.
This commit is based on @LGA1150(at GitHub)'s work
<a4932c8d5a>
With some changes:
1. Added `qpic_bam` node in dts. I don't know much about this,
but I observed other dtses have this node.
2. Removed `ldo` node under `sd_0_pinmux`, because `ldo` cause SD card not
working. This fix is from
<51143b4c75>
3. Removed the 32MB NOR variant.
4. Removed `cd-gpios` in `sdhci` node, because it's reported that it makes
wlan2g led light up.
5. Added ethphy led config in dts.
6. Changed nand partition label from `rootfs` to `ubi`.
About the 128MiB variant: The stock bootloader sets size of nand to 64MiB.
But most of this devices have 128MiB nand. If you want to use all 128MiB,
you need to modify the `MIBIB` data of bootloader. More details can be
found on github:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-818770060>
For instructions on how to flash the MIBIB partition from u-boot console:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-819138232>
About the Mini PCIe slot: (from "ygleg")
"The REFCLK signals on the Mini PCIe slot is not connected on
this board out of the box. If you want to use the Mini PCIe slot
on the board, you need to (preferably) solder two 0402 resistors:
R436 (REFCLK+) and R444 (REFCLK-)..."
This and much more information is provoided in the github comment:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-968054670>
Signed-off-by: Richard Yu <yurichard3839@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
[Added comment about MIBIB+128 MiB variant. Added commit
message section about pcie slot. Renamed gpio-leds' subnodes
and added color, function+enum properties.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Back in the day, the board-2.bin came with ath10k-firmware-qca4019.
This changed with
commit c3b2efaf24 ("linux-firmware: ath10k: add board firmware packages")
which placed the board-2.bin into a separate package: ath10k-board-qca4019.
This was great, because it addressed one of the caveat of the original
ipq-wifi package:
commit fa03d441e9 ("firmware: add custom IPQ wifi board definitions")
| 2. updating ath10k-firmware-qca4019 will also replace
| the board-2.bin. For this cases the user needs to
| manually reinstall the wifi-board package once the
| ath10k-firmware-qca4019 is updated.
This could be extended further so that ipq-wifi packages
no longer use "install-override" and the various QCA4019
variants list the ath10k-board-qca4019 as a CONFLICT
package.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
e983a25 Update regulatory rules for Ecuador (EC)
a0bcb88 wireless-regdb: Update regulatory rules for Norway (NO) on 6 and 60 GHz
cdf854d wireless-regdb: Update regulatory rules for Germany (DE) on 6GHz
86cba52 wireless-regdb: reduce bandwidth for 5730-5850 and 5850-5895 MHz in US
6fa2384 wireless-regdb: remove PTMP-ONLY from 5850-5895 MHz for US
9839e1e wireless-regdb: recent FCC report and order allows 5850-5895 immediately
42dfaf4 wireless-regdb: update 5725-5850 MHz rule for GB
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The official Plasma Cloud firmware adjusted the BDFs to contain new
conformance test limits and target power values. These should be imported
to avoid emissions outside the allowed limits.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The ipq-wifi-netgear_wac510 package is not selected by any device and would
be empty anyway. The default board-2.bin from ath10k-board-qca4019 is
therefore used for this device and the package doesn't provide any visible
features.
Fixes: b126d9c3a3 ("ipq40xx: add netgear wac510 support")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Some devices (such as Extreme Networks WS-AP3959i-ROW) do not contain
precal binaries in ART, and the precal in the cards eeprom causes
firmware load errors.
These firmware files were previously in linux-firmware,
so these are adding them back and renaming to be cleaner.
Signed-off-by: Damien Mascord <tusker@tusker.org>
In there linux-firmware repository located in kernel, there were removed old
broadcom firmware [1] as they seem to be likely vulnerable to KrØØk vulnerability
(CVE-2019-15126), because Cypress released new versions and superseded
by it.
In OpenWrt, there is Makefile for cypress-firmware, which already provides
the same named packages like it was in linux-firmware. For example, cypress-firmware-43455-sdio
provides brcmfmac-firmware-43455-sdio [2].
Changelog between 2020118 and 20210315:
3568f96 (tag: 20210315) linux-firmware: Update firmware file for Intel Bluetooth AX210
9e96e50 linux-firmware: Update firmware file for Intel Bluetooth AX200
c8d0db5 linux-firmware: Update firmware file for Intel Bluetooth AX201
5e2a387 Merge tag 'iwlwifi-fw-2021-03-05-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware into main
b0d3e31 rtw88: 8822c: Update normal firmware to v9.9.6
5a2fd63 iwlwifi: add new FWs from core59-66 release
4f54906 iwlwifi: update 9000-family firmwares
11b7607 iwlwifi: update 7265D firmware
e425f76 Merge branch 'add-silabs-wf200' of github.com:jerome-pouiller/linux-firmware into main
5ecd13f Mellanox: Add new mlxsw_spectrum firmware xx.2008.2406
58fb90a linux-firmware: add frimware for mediatek bluetooth chip (MT7921)
e576a1b rtw89: 8852a: add firmware v0.9.12.2
048a7cb WHENCE: add missing symlink for BananaPi M3
aa6c6e7 Add symlink for BananaPi M2 to brcmfmac43430-sdio config
58825f7 brcm: Fix Raspberry Pi 4B NVRAM file
520f71b silabs: add new firmware for WF200
f7915a0 amdgpu: add initial firmware for green sardine
80cb579 rtw88: RTL8822C: Update normal firmware to v9.9.5
b79d239 (tag: 20210208) Merge branch 'DG1-guc-huc-ADLS-dmc' of git://anongit.freedesktop.org/drm/drm-firmware into main
66970e1 Merge branch 'qcom-rb5' of https://github.com/lumag/linux-firmware into main
cf6fc2b Mellanox: Add new mlxsw_spectrum firmware xx.2008.2304
391fd50 linux-firmware: add firmware for MT7921
c5e3240 rtw88: RTL8821C: Update firmware to v24.8
d33d2d8 linux-firmware: Update firmware file for Intel Bluetooth AX210
3027ae4 linux-firmware: Update firmware file for Intel Bluetooth AX200
13979c3 linux-firmware: Update firmware file for Intel Bluetooth AX201
348d8a9 i915: Add DMC v2.01 for ADL-S
f33f1f7 i915: Add HuC v7.7.1 for DG1
6a422f5 i915: Add GuC v49.0.1 for DG1
df822a8 qcom: Add venus firmware files for VPU-1.0
11a1db1 qcom: Add SM8250 Compute DSP firmware
e55248b qcom: Add SM8250 Audio DSP firmware
da74cc6 qcom: add firmware files for Adreno a650
0578970 brcm: Link RPi4's WiFi firmware with DMI machine name.
d528862 brcm: Add NVRAM for Vamrs 96boards Rock960
870b805 brcm: Update Raspberry Pi 3B+/4B NVRAM for downstream changes
a28a590 cypress: Fix link direction
060ad8b cypress: Link the new cypress firmware to the old brcm files
0f0aefd brcm: remove old brcm firmwares that have newer cypress variants
f580dc2 rtl_bt: Update RTL8822C BT(UART I/F) FW to 0x059A_25CB
7df2220 rtl_bt: Update RTL8822C BT(USB I/F) FW to 0x099a_7253
e79405d rtl_bt: Add firmware and config files for RTL8852A BT USB chip
ef3813d rtl_bt: Update RTL8821C BT(USB I/F) FW to 0x829a_7644
646f159 (tag: 20201218) make AP6212 in bananpi m2 plus/zero work
28185ec linux-firmware: Update firmware file for Intel Bluetooth AX210
23da869 linux-firmware: Update firmware file for Intel Bluetooth AX200
2099248 linux-firmware: Update firmware file for Intel Bluetooth AX201
94de5e2 linux-firmware: Update firmware file for Intel Bluetooth 9560
27a3689 linux-firmware: Update firmware file for Intel Bluetooth 9260
5c3c4af Merge branch 'lt9611uxc' of https://github.com/lumag/linux-firmware into main
aaed4a8 Merge branch 'v1.1.6' of https://github.com/irui-wang/linux_fw_vpu_v1.1.6 into main
d8c9865 Merge branch 'master' of https://github.com/sampnimm/linux-firmware-BT into main
63ab3db linux-firmware: add firmware for Lontium LT9611UXC DSI to HDMI bridge
0fe0fe0 mediatek: update MT8173 VPU firmware to v1.1.6
1a08ec9 QCA : Updated firmware files for WCN3991
7455a36 Merge branch 'guc_v49' of git://anongit.freedesktop.org/drm/drm-firmware into main
7eb7fda linux-firmware: Update firmware file for Intel Bluetooth AX210
5cbf459 linux-firmware: Update firmware file for Intel Bluetooth AX210
c487f7d i915: Add GuC firmware v49.0.1 for all platforms
d9ffb07 i915: Remove duplicate KBL DMC entry
b362fd4 Mellanox: Add new mlxsw_spectrum firmware xx.2008.2018
bc9cd0b linux-firmware: Update AMD SEV firmware
54c797a amdgpu: add sienna cichlid firmware for 20.45
1340e9c amdgpu: update vega20 firmware for 20.45
b260c9c amdgpu: update vega12 firmware for 20.45
d683bd5 amdgpu: update vega10 firmware for 20.45
7c81cc2 amdgpu: update renoir firmware for 20.45
3619e57 amdgpu: update navi14 firmware for 20.45
68ce0fb amdgpu: update navi12 firmware for 20.45
e889b80 amdgpu: update navi10 firmware for 20.45
f4edc15 amdgpu: update raven2 firmware for 20.45
e71210f amdgpu: update raven firmware for 20.45
[1] https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/commit/?id=0f0aefd733f70beae4c0246edbd2c158d5ce974c
[2] eeda8652f1/package/firmware/cypress-firmware/Makefile (L124)
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
This adds support for the Netgear WAC510 Insight Managed Smart Cloud
Wireless Access Point, an indoor dual-band, dual-radio 802.11ac
business-class wireless AP with integrated omnidirectional antennae
and two 10/100/1000 Mbps Ethernet ports.
For more information see:
<https://www.netgear.com/business/wifi/access-points/wac510>
Specifications:
SoC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
Flash1: 2 MiB Winbond W25Q16JV SPI-NOR
Flash2: 128 MiB Winbond W25N01GVZEIG SPI-NAND
Ethernet: Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port,
WAN port active IEEE 802.3af/at PoE in
Wireless1: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
Wireless2: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae
Input: (Optional) Barrel 12 V 2.5 A Power, Reset button SW1
LEDs: Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN
Serial: Header J2
1 - 3.3 Volt (Do NOT connect!)
2 - TX
3 - RX
4 - Ground
WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter!
The Serial settings are 115200-8-N-1.
Installation via Stock Web Interface:
BTW: The default factory console/web interface login user/password are
admin/password.
In the web interface navigating to Management - Maintenance - Upgrade -
'Firmware Upgrade' will show you what is currently installed e.g.:
Manage Firmware
Current Firmware Version: V5.0.10.2
Backup Firmware Version: V1.2.5.11
Under 'Upgrade Options' choose Local (alternatively SFTP would be
available) then click/select 'Browse File' on the right side, choose
openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar
and hit the Upgrade button below. After a minute or two your browser
should indicate completion printing 'Firmware update complete.' and
'Rebooting AP...'.
Note that OpenWrt will use the WAN PoE port as actual WAN port
defaulting to DHCP client but NOT allowing LuCI access, use LAN port
defaulting to 192.168.1.1/24 to access LuCI.
Installation via TFTP Requiring Serial U-Boot Access:
Connect to the device's serial port and hit any key to stop autoboot.
Upload and boot the initramfs based OpenWrt image as follows:
(IPQ40xx) # setenv serverip 192.168.1.1
(IPQ40xx) # setenv ipaddr 192.168.1.2
(IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb
(IPQ40xx) # bootm
Note: This only runs OpenWrt from RAM and has not installed anything
to flash as of yet. One may permanently install OpenWrt as follows:
Check the MTD device number of the active partition:
root@OpenWrt:/# dmesg | grep 'set to be root filesystem'
[ 1.010084] mtd: device 9 (rootfs) set to be root filesystem
Upload the factory image ending with .ubi to /tmp (e.g. using scp or
tftp). Then flash the image as follows (substituting the 9 in mtd9
below with whatever number reported above):
root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi
And reboot.
Dual Image Configuration:
The default U-Boot boot command bootipq uses the U-Boot environment
variables primary/secondary to decide which image to boot. E.g.
primary=0, secondary=3800000 uses rootfs while primary=3800000,
secondary=0 uses rootfs_1.
Switching their values changes the active partition. E.g. from within
U-Boot:
(IPQ40xx) # setenv primary 0
(IPQ40xx) # setenv secondary 3800000
(IPQ40xx) # saveenv
Or from a OpenWrt userspace serial/SSH console:
fw_setenv primary 0
fw_setenv secondary 3800000
Note that if you install two copies of OpenWrt then each will have its
independent configuration not like when switching partitions on the
stock firmware.
BTW: The kernel log shows which boot partition is active:
[ 2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB)
vs.
[ 2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB)
Note: After 3 failed boot attempts it automatically switches partition.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[squashed netgear-tar commit into main and rename netgear-tar for
now, until it is made generic.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This marks all packages which depend on a target with @TARGET nonshared.
If they are not marked nonshared they would be build by the SDK build
and if this happens with a different SDK, then the SDK from the target
the package depends on, the package would not be added to the index.
This should fix the image builder for some of these packages.
This should fix the image builder at least for bcm27xx/bcm2710 and
bcm4908/generic.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD),
an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet
port.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 256 MB
- Storage: 16 MB NOR
- Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae
- Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in
- 1x Ethernet LED (green)
- 7x user-controllable LEDs
· 1x power (blue)
· 1x user (green)
· 5x rssi (green)
Note:
Serial UART is probably available on the board, but it has not been
tested.
Flashing:
Boot via TFTP the initramfs image. Then, upload a sysupgrade image
via SSH and flash it normally. More info at the "Common procedures
for MikroTik products" page https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Add firmware and board file for Qualcomm Atheros QCA9377 802.11ac Wireless
Network Adapter (rev 31) recognized as [168c:0042].
This card supports standard 1x1 802.11ac Wave2, BT5, and MU-MIMO.
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC
(hAP ac²), a indoor dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional antennae, USB port and five
10/100/1000 Mbps Ethernet ports.
See https://mikrotik.com/product/hap_ac2 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 128 MB
- Storage: 16 MB NOR
- Wireless:
· Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
· Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
- Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in
- 1x USB Type A port
Installation:
Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ls-ddr-phy package needs fiptool options that are not
available via the version from arm-trusted-firmware-tools.
This breaks build for layerscape with the recently added LX2160a:
create: unrecognized option '--ddr-immem-udimm-1d'
Use the tfa-layerscape variant again for now, but rename it to
fiptool-layerscape to indicate that it's a specific variant.
This reverts 84bc7d31e0 ("tfa-layerscape: don't build fiptool").
Fixes: f59d7aab2a ("layerscape: add ddr-phy package")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The QorIQ LX2160A reference design board provides a comprehensive platform
that enables design and evaluation of the LX2160A processor.
- Enables network intelligence with the next generation Datapath (DPPA2)
which provides differentiated offload and a rich set of IO, including
10GE, 25GE, 40GE, and PCIe Gen4
- Delivers unprecedented efficiency and new virtualized networks
- Supports designs in 5G packet processing, network function
virtualization, storage controller, white box switching, network
interface cards, and mobile edge computing
- Supports all three LX2 family members (16-core LX2160A; 12-core LX2120A;
and 8-core LX2080A)
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[use AUTORELEASE, add dtb to firmware part]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add ddr-phy package for layerscape. Currently only LX2160ARDB
requires the package.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[use AUTORELEASE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The LS1046A Freeway board (FRWY) is a high-performance computing,
evaluation, and development platform that supports the QorIQ
LS1046A architecture processor capable of support more than 32,000
CoreMark performance. The FRWY-LS1046A board supports the QorIQ
LS1046A processor, onboard DDR4 memory, multiple Gigabit Ethernet,
USB3.0 and M2_Type_E interfaces for Wi-Fi.
The FRWY-LS1046A-TP includes the Coral Tensor Flow Processing Unit
that offloads AI/ML inferencing from the CPU to provide significant
boost for AI/ML applications. The FRWY-LS1046A-TP includes one M.2
TPU module and more modules can easily be added including USB
versions of the module to scale the AI/ML performance.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[rebase, use AUTORELEASE, fix sorting, add dtb to firmware part]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Multiple sources are hosted on OpenWrts source server only. The source
URLs to point to the server vary based on different epochs in OpenWrts
history.
Replace all by @OPENWRT which is an "empty" mirror, therefore using the
fallback servers sources.cdn.openwrt.org and sources.openwrt.org.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This patch adds wil6210 firmware and board files.
Firmware version is not up to date but is only freely redistributable one I found.
Board file is a generic one so most devices and especially those for long distance
PtP links will require so in a ipq-wifi like way.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
FLASH1: 4 MiB NOR
FLASH2: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: Reset
LED: Power, Internet
UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
OTHER: On board with BLE module - by cp210x USB serial chip
On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed
Install via uboot tftp or uboot web failsafe.
By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi
(IPQ40xx) # run lf
By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
The Makefile is rejecting all files with for a given prefix (here
"board-plasmacloud_pa2200") when it didn't match a known suffix. Instead it
stops the build with an error like:
Makefile:135: *** Unrecognized board-file suffix '.ipq4019' for 'board-plasmacloud_pa2200.ipq4019'. Stop.
The correct suffix for the QCA4019/hw1.0 is qca4019 and not ipq4019.
Fixes: 4871fd2616 ("ipq40xx: add support for Plasma Cloud PA2200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The Makefile is rejecting all files with for a given prefix (here
"board-plasmacloud_pa1200") when it didn't match a known suffix. Instead it
stops the build with an error like:
Makefile:135: *** Unrecognized board-file suffix '.ipq4019' for 'board-plasmacloud_pa1200.ipq4019'. Stop.
The correct suffix for the QCA4019/hw1.0 is qca4019 and not ipq4019.
Fixes: ea5bb6bbfe ("ipq40xx: add support for Plasma Cloud PA1200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v71) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8075 (2 ports)
PLC: MaxLinear G.hn 88LX5152
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET, WiFi, PLC Button
LEDS: red/white home, white WiFi
To modify a retail device to run OpenWRT firmware:
1) Setup a TFTP server on IP address 192.168.0.100 and copy the OpenWRT
initramfs (initramfs-fit-uImage.itb) to the TFTP root as 'uploadfile'.
2) Power on the device while pressing the recessed reset button next to
the Ethernet ports. This causes the bootloader to retrieve and start
the initramfs.
3) Once the initramfs is booted, the device will come up with IP
192.168.1.1. You can then connect through SSH (allow some time for
the first connection).
4) On the device shell, run 'fw_printenv' to show the U-boot environment.
Backup this information since it contains device unique factory data.
5) Change the boot command to support booting OpenWRT:
# fw_setenv bootcmd 'sf probe && sf read 0x84000000 0x180000 0x400000 && bootm'
6) Change directory to /tmp, download the sysupgrade (e.g. through wget)
and install it with sysupgrade. The device will reboot into OpenWRT.
Notice that there is currently no support for booting the G.hn chip.
This requires userland software we lack the rights to share right now.
Signed-off-by: Stefan Schake <stefan.schake@devolo.de>
Device specifications:
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200
* GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE
* GPIO-LEDs for power (orange) and status (blue)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3at POE+
+ used as WAN interface
* 12V 2A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
* QCA IPQ4018
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200
* 3x GPIO-LEDs for status (cyan, purple, yellow)
* 1x GPIO-button (reset)
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio4:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio3:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3af/at POE(+)
+ used as WAN interface
* 12V/24V 1A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All firmwares were added to linux-firmware, so there's no need to keep this
package definitions.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Instead of duplicating board firmware binaries, which are exactly the same
as the ones from linux-firmware, add dependencies and remove duplicated
downloads.
Runtime-tested on ath79 (TP-Link Archer C7 v2) and ipq806x (Netgear R7800).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Split ath10k firmwares into board and firmware packages.
This way we can add dependencies to ath10k-ct firmware packages.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
There are linux firmwares packages for 43362, 43430 and 43455 which shouldn't
be installed at the same time as Cypress firmwares.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This expands packages to define not only provides but also conflicts.
These packages provides same files so they should specify conflicts.
Second expansion is that *-ct-htt and *-ct-full-htt firmwares can also
provide *-ct variant as that allows explicit dependency on CT variant
with various firmware modifications.
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
[Bump PKG_RELEASE and format PROVIDES/CONFLICTS]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This patch add missing support of SC16IS740 serial controller, installed
on LS1012A-FRDM board.
It was required to change RCW bits, because SPI was disabled by default.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Update ls-rcw to LSDK-20.04-update-290520.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[rebase, fix PKG_RELEASE change]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds several stylistic and functional improvements of the recently
added Edgecore ECW5211, especially:
* Drop the local BDFs as those are already in the upstream under different names
* Add SPDX tag to DTS
* Add label MAC address
* Move LED trigger to DTS
* Remove unnecessary status="okay"
* Disable unused SS USB phy as the USB port only supports USB 2.0
* Make uboot-env partition writable
* Remove qcom,poll_required_dynamic property as the driver does not use it
* Tidy up the device recipe
Fixes: 4488b260a0 ("ipq40xx: add Edgecore ECW5211 support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Acked-by: Robert Marko <robert.marko@sartura.hr>
00a84c5 linux-firmware: Update AMD SEV firmware
71338c2 Merge branch 'for-master' of https://github.com/CosmicPenguin/linux-firmware into main
07367b9 linux-firmware: Update firmware file for Intel Bluetooth AX200
1d1586a linux-firmware: Update firmware file for Intel Bluetooth AX201
28b333d linux-firmware: Update firmware file for Intel Bluetooth 9560
db30380 linux-firmware: Update firmware file for Intel Bluetooth 9260
eb3aa1f Mellanox: Add new mlxsw_spectrum firmware xx.2008.1310
ec88f05 mediatek: update MT7915 firmware to 20200819
a9993f8 brcm: Fix a stale symlink for RPi3 model b+
f48fec4 qcom: Add updated a5xx and a6xx microcode
d5f9eea wl18xx: update firmware file 8.9.0.0.83
7a237c6 linux-firmware: mt7615: update firmware to 20200814 version
74bd44f amdgpu: add navi12 firmware from 20.30
b9f69cd amdgpu: update navi10 firmware for 20.30
Signed-off-by: David Bauer <mail@david-bauer.net>
The firmware for Wave1 chips was updated to the latest release
10.2.4-1.0-00047 at the end of 2019 (commit 513d70cc50b).
Package firmware for these chips from linux-firmware.
This avoids downloading the ath10k-firmware repository.
Signed-off-by: David Bauer <mail@david-bauer.net>
The Linksys MR8300 is based on QCA4019 and QCA9888
and provides three, independent radios.
NAND provides two, alternate kernel/firmware images
with fail-over provided by the OEM U-Boot.
Hardware Highlights:
SoC: IPQ4019 at 717 MHz (4 CPUs)
RAM: 512MB RAM
SoC: Qualcomm IPQ4019 at 717 MHz (4 CPUs)
RAM: 512M DDR3
FLASH: 256 MB NAND (Winbond W29N02GV, 8-bit parallel)
ETH: Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks)
BTN: Reset and WPS
USB: USB3.0, single port on rear with LED
SERIAL: Serial pads internal (unpopulated)
LED: Four status lights on top + USB LED
WIFI1: 2x2:2 QCA4019 2.4 GHz radio on ch. 1-14
WIFI2: 2x2:2 QCA4019 5 GHz radio on ch. 36-64
WIFI3: 2x2:2 QCA9888 5 GHz radio on ch. 100-165
Support is based on the already supported EA8300.
Key differences:
EA8300 has 256MB RAM where MR8300 has 512MB RAM.
MR8300 has a revised top panel LED setup.
Installation:
"Factory" images may be installed directly through the OEM GUI using
URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1)
Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com>
[copied Hardware-highlights from EA8300. Fixed alphabetical order.
fixed commit subject, removed bogus unit-address of keys,
fixed author (used Signed-off-By to From:) ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Luma Home WRTQ-329ACN, also known as Luma WiFi System, is a dual-band
wireless access point.
Specification
SoC: Qualcomm Atheros IPQ4018
RAM: 256 MB DDR3
Flash: 2 MB SPI NOR
128 MB SPI NAND
WIFI: 2.4 GHz 2T2R integrated
5 GHz 2T2R integrated
Ethernet: 2x 10/100/1000 Mbps QCA8075
USB: 1x 2.0
Bluetooth: 1x 4.0 CSR8510 A10, connected to USB bus
LEDS: 16x multicolor LEDs ring, controlled by MSP430G2403 MCU
Buttons: 1x GPIO controlled
EEPROM: 16 Kbit, compatible with AT24C16
UART: row of 4 holes marked on PCB as J19, starting count from the side
of J19 marking on PCB
1. GND, 2. RX, 3. TX, 4. 3.3V
baud: 115200, parity: none, flow control: none
The device supports OTA or USB flash drive updates, unfotunately they
are signed. Until the signing key is known, the UART access is mandatory
for installation. The difficult part is disassembling the casing, there
are a lot of latches holding it together.
Teardown
Prepare three thin, but sturdy, prying tools. Place the device with back
of it facing upwards. Start with the wall having a small notch. Insert
first tool, until You'll feel resistance and keep it there. Repeat the
procedure for neighbouring walls. With applying a pressure, one edge of
the back cover should pop up. Now carefully slide one of the tools to
free the rest of the latches.
There's no need to solder pins to the UART holes, You can use hook clips,
but wiring them outside the casing, will ease debuging and recovery if
problems occur.
Installation
1. Prepare TFTP server with OpenWrt initramfs image.
2. Connect to UART port (don't connect the voltage pin).
3. Connect to LAN port.
4. Power on the device, carefully observe the console output and when
asked quickly enter the failsafe mode.
5. Invoke 'mount_root'.
6. After the overlayfs is mounted run:
fw_setenv bootdelay 3
This will allow to access U-Boot shell.
7. Reboot the device and when prompted to stop autoboot, hit any key.
8. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use
'setenv' to do that, then run following commands:
tftpboot 0x84000000 <openwrt_initramfs_image_name>
bootm 0x84000000
and wait till OpenWrt boots.
9. In OpenWrt command line run following commands:
fw_setenv openwrt "setenv mtdids nand1=spi_nand; setenv mtdparts mtdparts=spi_nand:-(ubi); ubi part ubi; ubi read 0x84000000 kernel; bootm 0x84000000"
fw_setenv bootcmd "run openwrt"
10. Transfer OpenWrt sysupgrade image to /tmp directory and flash it
with:
ubirmvol /dev/ubi0 -N ubi_rootfs
sysupgrade -v -n /tmp/<openwrt_sysupgrade_image_name>
11. After flashing, the access point will reboot to OpenWrt, then it's
ready for configuration.
Reverting to OEM firmware
1. Execute installation guide steps: 1, 2, 3, 7, 8.
2. In OpenWrt command line run following commands:
ubirmvol /dev/ubi0 -N rootfs_data
ubirmvol /dev/ubi0 -N rootfs
ubirmvol /dev/ubi0 -N kernel
ubirename /dev/ubi0 kernel1 kernel ubi_rootfs1 ubi_rootfs
ubimkvol /dev/ubi0 -S 34 -N kernel1
ubimkvol /dev/ubi0 -S 320 -N ubi_rootfs1
ubimkvol /dev/ubi0 -S 264 -N rootfs_data
fw_setenv bootcmd bootipq
3. Reboot.
Known issues
The LEDs ring doesn't have any dedicated driver or application to control
it, the only available option atm is to manipulate it with 'i2cset'
command. The default action after applying power to device is spinning
blue light. This light will stay active at all time. To disable it
install 'i2c-tools' with opkg and run:
i2cset -y 2 0x48 3 1 0 0 i
The light will stay off until next cold boot.
Additional information
After completing 5. step from installation guide, one can disable asking
for root password on OEM firmware by running:
sed -e 's/root❌/root::/' -i /etc/passwd
This is useful for investigating the OEM firmware. One can look
at the communication between the stock firmware and the vendor's
cloud servers or as a way of making a backup of both flash chips.
The root password seems to be constant across all sold devices.
This is output of 'led_ctl' from OEM firmware to illustrate
possibilities of LEDs ring:
Usage: led_ctl [status | upgrade | force_upgrade | version]
led_ctl solid COLOR <brightness>
led_ctl single COLOR INDEX <brightness 0 - 15>
led_ctl spinning COLOR <period 1 - 16 (lower = faster)>
led_ctl fill COLOR <period 1 - 16 (lower = faster)>
( default is 5 )
led_ctl flashing COLOR <on dur 1 - 128> <off dur 1 - 128>
(default is 34) ( default is 34 )
led_ctl pulsing COLOR
COLOR: red, green, blue, yellow, purple, cyan, white
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[squash "ipq-wifi: add BDFs for Luma Home WRTQ-329ACN" into commit,
changed ubi volumes for easier integration, slightly reworded
commit message, changed ubi volume layout to use standard names all
around]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
amd64-microcode (3.20191218.1)
* New microcode update packages from AMD upstream:
+ Removed Microcode updates (known to cause issues):
sig 0x00830f10, patch id 0x08301025, 2019-07-11
* README: update for new release
amd64-microcode (3.20191021.1)
* New microcode update packages from AMD upstream:
+ New Microcodes:
sig 0x00830f10, patch id 0x08301025, 2019-07-11
+ Updated Microcodes:
sig 0x00800f12, patch id 0x08001250, 2019-04-16
sig 0x00800f82, patch id 0x0800820d, 2019-04-16
amd64-microcode (3.20181128.1)
* New microcode update packages from AMD upstream:
+ New Microcodes:
sig 0x00800f82, patch id 0x0800820b, 2018-06-20
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
flashing the unit
* first update to latest edcore FW as per the PDF instructions
* boot the initramfs
- tftpboot 0x88000000 openwrt-ipq40xx-generic-edgecore_oap100-initramfs-fit-uImage.itb; bootm
* inside the initramfs call the following commiands
- ubiattach -p /dev/mtd0
- ubirmvol /dev/ubi0 -n0
- ubirmvol /dev/ubi0 -n1
- ubirmvol /dev/ubi0 -n2
* scp the sysupgrade image to the board and call
- sysupgrade -n openwrt-ipq40xx-generic-edgecore_oap100-squashfs-nand-sysupgrade.bin
Signed-off-by: John Crispin <john@phrozen.org>
This patch adds support for the Edgecore ECW5211 indoor AP.
Specification:
- SoC: Qualcomm Atheros IPQ4018 ARMv7-A 4x Cortex A-7
- RAM: 256MB DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB MX35LFxGE4AB SPI-NAND
- Ethernet: 2 x 1G via Q8075 PHY connected to ethernet adapter via PSGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: Built-in IPQ4018 (2x2 802.11bng, 2x2 802.11 acn)
- CC2540 BLE connected to USB 2.0 port
- Atmel AT97SC3205T I2C TPM
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This patch adds support for the Edgecore ECW5410 indoor AP.
Specification:
- SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15
- RAM: 256MB(225 usable) DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB S34MS01G2 Parallel NAND
- Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn)
- CC2540 BLE
- UART console on RJ45 next to ethernet ports exposed.
Its Cisco pin compatible, 115200 8n1 baud.
Installation instructions:
Through stock firmware or initramfs.
1.Connect to console
2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe.
3. Transfer factory image
4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path>
This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0
Note
Initramfs:
1. Connect to console
2. Transfer the image from TFTP server with tftpboot,
or by using DHCP advertised image with dhcp command.
3. bootm
4. Run ubiformat /dev/mtd1
You need to interrupt the bootloader after rebooting and run:
run altbootcmd
This will switch your active rootfs partition to one you wrote to and boot from it.
So if rootfs1 is active, then it will change it to rootfs2.
This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0
If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those.
This will result in wrong ordering and OpenWrt will panic on boot.
5. Transfer sysupgrade image
6. Flash with sysupgrade -n.
Note that sysupgrade will write the image to rootfs partition that is not currently in use.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This enables the ipq-wifi package to be used on IPQ806x target.
Its needed for boards using a different BDF than one shipped in the upstream board-2.bin.
Currently needed for Edgecore ECW5410.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Instead of using http and https for source downloads from
downloads.openwrt.org, always use https for it's better security.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This target has been mostly replaced by ath79 and won't be included
in the upcoming release anymore. Finally put it to rest.
This also removes all references in packages, tools, etc. as well as
the uboot-ar71xx and vsc73x5-ucode packages.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For example, Turris MOX SDIO card is using Marvell (NXP) 88W8997 chip.
Technical specs of 88W8997:
- 28nm
- 802.11 ac wave-2
It should support simultaneous dual-band 2.4 GHz and 5 GHz,
but it requires to support multiSSID for one Wi-Fi card [1], which is
not supported in OpenWrt, yet and if we tried to run two instances of
hostapd, it didn't work well, so it's 2.4 GHz or 5 GHz.
- 2x2 MU-MIMO
- Bluetooth 5.1 with LE support
- Unfortunately, there can be connected only 8 clients at the same time
(limited by FW, however, there exists "enterprise" chip, its equal chip,
it is just different that it uses different FW)
Symlink is necessary as mwifiex_sdio tries to load sd8997_uapsta.bin
[ 13.651182] mwifiex_sdio mmc0:0001:1: Direct firmware load for mrvl/sd8997_uapsta.bin failed with error -2
[ 13.661065] mwifiex_sdio mmc0:0001:1: Falling back to user helper
[ 13.684880] firmware mrvl!sd8997_uapsta.bin: firmware_loading_store: map pages failed
[ 13.695910] mwifiex_sdio mmc0:0001:1: Failed to get firmware mrvl/sd8997_uapsta.bin
[ 13.703774] mwifiex_sdio mmc0:0001:1: info: _mwifiex_fw_dpc: unregister device
Pali Rohár sent two patches [2] [3] into kernel to fix default firmware name for SD8997, so
the symlink will not be required in the future versions of kernel, which
was accepted and right now, according to my details it was backported to 5.8, 5.7 and 5.4
[1] https://bugs.openwrt.org/index.php?do=details&task_id=3243
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=00eb0cb36fad5
[3] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=2e1fcac52a9ea
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Not a large change from last time, but should fix at least one rare wave-2
crash. The htt-mgt-community builds are trimmed for supporting lots of
stations (typically 150+ stations per radio).
Tested on Netgear R7800.
Signed-off-by: Michael Yartys <michael.yartys@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
OpenWrt lately has harmonized device (definition) names to the
pattern vendor_model to improve overall consistency, also with
other values like the DTS compatible.
This patch applies that scheme to the layerscape target.
Since this (intentionally) creates a bigger overlap between DTS names,
compatible, and device definition name, it also moves DEVICE_DTS and
SUPPORTED_DEVICES definitions to the Device/Default blocks.
Apart from that, it also modifies several packages to use consistent
naming in order to keep the $(1) file references working.
While at it, remove one layer of complexity for the setup in
tfa-layerscape package.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Quoting part of original message from eefb5f741015 commit in
linux-firmware repository:
This adds the "minifw" version of the EIP197 firmware, which the inside-
secure driver will use as a fallback if the original full-featured
firmware cannot be found. This allows for using the inside-secure driver
and hardware without access to "official" firmware only available under
NDA.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019.
Specification
-------------
- SoC: Qualcomm IPQ4019
- RAM: 512MiB
- Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC)
- Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch)
- Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch)
- Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN)
- LED: 4x white LED, 4x orange LED, 1x blue LED
- USB: 1x USB 3.0 port
- Input: 2x tactile switch, 2x slide switch (2x SP3T)
- Serial console: 115200bps, pinheader JP5 on PCB
- Power: DC 12V 2A
Flash instruction
-----------------
1. Set up a TFTP server (IP address: 192.168.11.10)
2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage"
and put it into the TFTP server directory.
3. Connect the TFTP server and WTR-M2133HP.
4. Hold down the AOSS button, then power on the router.
5. After booting OpenWrt initramfs image, connect to the router by SSH.
6. Transfer "squashfs-nand-factory.ubi" to the router.
7. Execute the following commands.
# ubidetach -p /dev/mtd15
# ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi
# fw_setenv bootcmd bootipq
8. Perform reboot.
Recover to stock firmware
-------------------------
1. Execute the following command.
# fw_setenv bootcmd bootbf
2. Reboot and wait several minutes.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Specifications:
SOC: Qualcomm IPQ4029 (DAKOTA) ARM Quad-Core
RAM: 512 MiB
FLASH1: 16 MiB NOR - SPI0
FLASH2: 8 GiB eMMC
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4029 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4029 5GHz 802.11n/ac W2 2x2
INPUT: Reset, WPS
LED: Power, Mesh, WLAN
UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
UART2: On board with BLE module
SPI1: On board socket for Zigbee module
Install via tftp
- NB: need to flash transition image firstly
Firstly install transition image:
(IPQ40xx) # tftpboot 0x84000000 s1300-factory-to-openwrt.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script
Secondly install openwrt sysupgrade bin:
(IPQ40xx) # run lf
Revert to factory image:
(IPQ40xx) # tftpboot 0x84000000 s1300-openwrt-to-factory.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script
The kernel and rootfs of factory firmware are on eMMC, and openwrt
firmware is on NOR flash. The transition image includes U-boot
and partition table, which decides where to load kernel and rootfs.
After you firstly install openwrt image, you can switch between
factory and openwrt firmware by flashing transition image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8072 (2 ports)
USB: 1 x 2.0 (Host controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button
LEDS: White, Blue, Red, Orange
Flash instruction:
From EnGenius firmware to OpenWrt firmware:
In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emr3500-squashfs-factory.bin directly.
From OpenWrt firmware to EnGenius firmware:
1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
Put the EnGenius firmware in the TFTP server directory on your computer.
2. Power up EMR3500. Press 4 and then press any key to enter u-boot.
3. Download EnGenius firmware
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emr3500-nor-fw-s.img
4. Flash the firmware
(IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script
5. Reboot
(IPQ40xx) # reset
Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com>
[squashed update patch, updated to 5.4, dropped BOARD_NAME,
migrated to SOC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
We do not have to define package for each board, and
consider variant's installing.
It is easier to maintain ls-dpl with only one package
installing all 4 files as intermediate files.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
We do not have to define package for each board, and
consider variant's installing.
It is easier to maintain ls-mc with only one package
installing all two images as intermediate files.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
We do not have to define package for each board, and
consider variant's installing.
It is easier to maintain fman-ucode with only one package
installing all two binaries as intermediate files.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Update ls-rcw to latest LSDK-20.04.
Update patch 0001 with a new one.
Drop patch 0002 since it had been integrated.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
We do not have to define package for each board, and
consider variant's building/installing.
It is easier to maintain ls-rcw with only one package
installing all boards RCW binaries as intermediate
files, each of which is just about hundreds of bytes.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
For wave-2, there is now a new variant: htt-mgt-community (vs the old
full-htt-mgt-community).
The non-full one (hence forth 'diet') compiles out a lot of firmware features
that ath10k does not use. This saves a lot of resources and lets one
configure more stations/vdevs/etc using fwcfg.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Another release is overdue for quite some time, so I'm backporting three
fixes from upstream which I plan to backport into 19.07 as well.
Ref: FS#2880
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Cell C RTL30VW is a LTE router with tho gigabit ethernets and integrated
QMI mPCIE modem.
This is stripped version of ASKEY RTL0030VW.
Hardware:
Specification:
-CPU: IPQ4019
-RAM: 256MB
-Flash: NAND 128MB + NOR 16MB
-WiFi: Integrated bgn/ac
-LTE: mPCIe card (Modem chipset MDM9230)
-LAN: 2 Gigabit Ports
-USB: 2x USB2.0
-Serial console: RJ-45 115200 8n1
-Unsupported VoIP
Known issues:
None so far.
Instruction install:
There are two methods: Factory web-gui and serial + tftp.
Web-gui:
1. Apply factory image via stock web-gui.
Serial + initramfs:
1. Rename OpenWrt initramfs image to "image"
2. Connect serial console (115200,8n1)
3. Set IP to different than 192.168.1.11, but 24 bit mask, eg. 192.168.1.4.
4. U-Boot commands:
sf probe && sf read 0x80000000 0x180000 0x10000
setenv serverip 192.168.1.4
set fdt_high 0x85000000
tftpboot 0x84000000 image
bootm 0x84000000
5. Install sysupgrade image via "sysupgrade -n"
Back to stock:
All is needed is swap 0x4c byte in mtd8 from 0 to 1 or 1 to 0,
do firstboot and factory reset with OFW:
1. read mtd8:
dd if=/dev/mtd8 of=/tmp/mtd8
2. go to tmp:
cd /tmp/
3. write first part of partition:
dd if=mtd8 of=mtd8.new bs=1 count=76
4. check which layout uses bootloader:
cat /proc/mtd
5a. If first are kernel_1 and rootfs_1 write 0:
echo -n -e '\x00' >> mtd8.new
5b. If first are kernel and rootfs write 1:
echo -n -e '\x01' >> mtd8.new
6. fill with rest of data:
dd if=mtd8 bs=1 skip=77 >> mtd8.new
7. CHECK IF mtd8.new HAVE CHANGED ONLY ONE BYTE! e.g with:
hexdump mtd8.new
8. write new mtd8 to flash:
mtd write mtd8.new /dev/mtd8
9. do firstboot
10.reboot
11. Do back to factory defaults in OFW GUI.
Based on work: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
MobiPromo CM520-79F is an AC1300 dual band router based on IPQ4019
Specification:
SoC/Wireless: QCA IPQ4019
RAM: 512MiB
Flash: 128MiB SLC NAND
Ethernet PHY: QCA8075
Ethernet ports: 1x WAN, 2x LAN
LEDs: 7 LEDs
2 (USB, CAN) are GPIO
other 5 (2.4G, 5G, LAN1, LAN2, WAN) are connected to a shift register
Button: Reset
Flash instruction:
Disassemble the router, connect UART pins like this:
GND TX RX
[x x . . x .]
[. . . . . .]
(QCA8075 and IPQ4019 below)
Baud-rate: 115200
Set up TFTP server: IP 192.168.1.188/24
Power on the router and interrupt the booting with UART console
env backup (in case you want to go back to stock and need it there):
printenv
(Copy the output to somewhere save)
Set bootenv:
setenv set_ubi 'set mtdids nand0=nand0; set mtdparts mtdparts=nand0:0x7480000@0xb80000(fs); ubi part fs'
setenv bootkernel 'ubi read 0x84000000 kernel; bootm 0x84000000#config@1'
setenv cm520_boot 'run set_ubi; run bootkernel'
setenv bootcmd 'run cm520_boot'
setenv bootargs
saveenv
Boot initramfs from TFTP:
tftpboot openwrt-ipq40xx-generic-mobipromo_cm520-79f-initramfs-fit-zImage.itb
bootm
After initramfs image is booted, backup rootfs partition in case of reverting to stock image
cat /dev/mtd12 > /tmp/mtd12.bin
Then fetch it via SCP
Upload nand-factory.ubi to /tmp via SCP, then run
mtd erase rootfs
mtd write /tmp/*nand-factory.ubi rootfs
reboot
To revert to stock image, restore default bootenv in uboot UART console
setenv bootcmd 'bootipq'
printenv
use the saved dump you did back when you installed OpenWrt to verify that
there are no other differences from back in the day.
saveenv
upload the backed up mtd12.bin and run
tftpboot mtd12.bin
nand erase 0xb80000 0x7480000
nand write 0x84000000 0xb80000 0x7480000
The BOOTCONFIG may have been configured to boot from alternate partition (rootfs_1) instead
In case of this, set it back to rootfs:
cd /tmp
cat /dev/mtd7 > mtd7.bin
echo -ne '\x0b' | dd of=mtd7.bin conv=notrunc bs=1 count=1 seek=4
for i in 28 48 68 108; do
dd if=/dev/zero of=mtd7.bin conv=notrunc bs=1 count=1 seek=$i
done
mtd write mtd7.bin BOOTCONFIG
mtd write mtd7.bin BOOTCONFIG1
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[renamed volume to ubi to support autoboot,
as per David Lam's test in PR#2432]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Release notes for 017:
Wave-1:
* March 19, 2020: Fix problem where power-save was not enabled when going off-channel to scan.
The problem was a boolean logic inversion in the chmgr code, a regression I introduced
a long time ago.
* March 19, 2020: When scanning only on current working channel, do not bother with disable/enable
powersave. This should make an on-channel scan less obtrusive than it was previously.
* March 23, 2020: Fix channel-mgr use-after-free problem that caused crashes in some cases. The crash
was exacerbated by recent power-save changes.
* March 23, 2020: Fix station-mode power-save related crash: backported the fix from 10.2 QCA firmware.
* March 23, 2020: Attempt to better clean up power-save objects and state, especially in station mode.
Release notes for 016:
Wave-1 changes, some debugging code for a crash someone reported, plus:
* February 28, 2020: Fix custom-tx path when sending in 0x0 for rate-code. Have tries == 0 mean
one try but NO-ACK (similar to how wave-2 does it).
wave-2:
* Fixed some long-ago regressions related to powersave and/or multicast. Maybe fix some
additional multicast and/or tx-scheduling bugs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
Re-add support for NXP FRDM-LS1012A, which mimics the flash layout of the
rest boards supported by LSDK.
0x000000000000-0x000000100000 : "bl2"
0x000000100000-0x000000500000 : "fip"
0x000000500000-0x000000600000 : "u-boot-env"
0x000000600000-0x000000a00000 : "reserved-1"
0x000000a00000-0x000000d00000 : "pfe"
0x000000d00000-0x000000f00000 : "reserved-2"
0x000000f00000-0x000001000000 : "dtb"
0x000001000000-0x000002000000 : "kernel"
0x000002000000-0x000004000000 : "ubifs"
Specification
SoC: LS1012A single core 800MHz
RAM: 512 MB DDR3
Flash: 64 MB QSPI NOR
Ethernet: 2x 10/100/1000 Mbps
Connectors: µUSB 3.0 OTG
µUSB 2.0 (debugging & power input)
2x 3.5mm jack for microphone & headphone (SGTL5000)
Arduino Shield expansion with I2C, SPI, UART, and GPIO
JTAG
LEDS: 3x (non-configurable)
Buttons: 1x (reset, non-configurable)
Be advised that erasing or writing 64MB flash takes some time to finish.
Do not reset the board until all operations end with success, otherwise
You'll need external tools to re-program the flash chip.
Installation
Follow the QSPI programing procedure for LS1012AFRWY board in
target/linux/layerscape/README, point 3.3.
Don't forget about updating U-Boot environment with MAC addresses of
ethernet interfaces, variable 'ethaddr' for eth0 and 'eth1addr' for eth1.
As the LSDK images do not support sysupgrade, nor do changes in this
commit, it's planed in upcoming submissions.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This patch adds support for the 8devices Habanero development board.
Specs are:
CPU: QCA IPQ4019
RAM: DDR3L 512MB
Storage: 32MB SPI-NOR and optional Parallel SLC NAND(Some boards ship with it and some without)
WLAN1: 2.4 GHz built into IPQ4019 (802.11n) 2x2
WLAN2: 5 GHz built into IPO4019 (802.11ac Wawe-2) 2x2
Ethernet: 5x Gbit LAN (QCA 8075)
USB: 1x USB 2.0 and 1x USB 3.0 (Both built into IPQ4019)
MicroSD slot (Uses SD controller built into IPQ4019)
SDIO3.0/EMMC slot (Uses the same SD controller)
Mini PCI-E Gen 2.0 slot (Built into IPQ4019)
5x LEDs (4 GPIO controllable)
2x Pushbutton (1 is connected to GPIO, other to SoC reset)
LCD ZIF socket (Uses the LCD controller built into IPQ4019 which has no driver support)
1x UART 115200 rate on J18
2x breakout development headers
12V DC Jack for power
DIP switch for bootstrap configuration
Installation instructions:
Since boards ship with vendors fork of OpenWrt sysupgrade can be used.
Signed-off-by: Robert Marko <robimarko@gmail.com>
SOC: IPQ4019 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB
FLASH: NOR 4 MiB + NAND 128 MiB
ETH: Qualcomm Atheros QCA8072
WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11a/n/ac 2:2x2
WLAN2: Qualcomm Atheros QCA9888 5GHz 802.11a/n/ac 2:2x2
INPUT: WPS Button
LEDS: Power, LAN1, LAN2, WLAN 2.4GHz, WLAN 5GHz-1, WLAN 5GHz-2, OPMODE
1. Load Ramdisk via U-Boot
To set up the flash memory environment, do the following:
a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters:
* 115200bps
* 8N1
b. Confirm that the PC is connected to the board using one of the Ethernet ports.
c. Set a static ip 192.168.99.8 for Ethernet that connects to board.
d. The PC must have a TFTP server launched and listening on the interface to which the board is connected.
e. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown.
U-BOOT> set serverip 192.168.99.9 && tftpboot 0x84000000 192.168.99.8:openwrt.itb && bootm
Signed-off-by: Steven Lin <steven.lin@senao.com>
[copied 4.19 dts to 5.4]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.
Despite, since subtargets range from bcm2708 to bcm2711, it seems
appropriate to use bcm27xx instead of bcm2708 (again, as already done
for BOARDNAME).
This also renames the packages brcm2708-userland and brcm2708-gpu-fw.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
This supports better per-chain noise floor reporting, which in turn allows for
better RSSI reporting in the driver.
Wave-2 fixes a long-standing rate-ctrl problem when connected to xbox (and probably other devices).
Wave-2 has fix for crash likely related to rekeying.
Wave-1 has some debugging code added where a user reported a crash.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq806x+qca9984,ipq4019+qca9986]
Signed-off-by: Michael Yartys <michael.yartys@protonmail.com>
This patch converts the Qxwlan E2600AC image away from
the deprecated .bin file and to the new .qca4019 method.
As a result, we no longer need to carry around the
legacy support for handling .bin files.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8072 (1 port)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button
LEDS: White, Blue, Red, Orange
Flash instruction:
From EnGenius firmware to OpenWrt firmware:
In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emd1-squashfs-factory.bin directly.
From OpenWrt firmware to EnGenius firmware:
1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
Put the EnGenius firmware in the TFTP server directory on your computer.
2. Power up EMD1. Press 4 and then press any key to enter u-boot.
3. Download EnGenius firmware
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emd1-nor-fw-s.img
4. Flash the firmware
(IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script
5. Reboot
(IPQ40xx) # reset
Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com>
[removed BOARD_NAME]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Specifications
==============
- SOC: IPQ4018
- RAM: DDR3 256MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: IPQ4018, 2x2, front end SKY85303-11
- 5GHz: IPQ4018, 2x2, front end SKY85717-21
- Ethernet: 1x 10/100/1000Mbps, POE 802.3af
- PHY: QCA8072
- UART: GND, blocked, 3.3V, RX, TX / 115200 8N1
- LED: 1x red / green
- Button: 1x reset / factory default
- U-Boot bootloader with tftp and "emergency web server" accessible
using serial port.
Installation
============
Flash factory image from D-Link web UI. Constraints in the D-Link web UI
makes the factory image unnecessarily large. Flash again using
sysupgrade from inside OpenWrt to reclaim some flash space.
Return to stock D-Link firmware
===============================
Partition layout is preserved, and it is possible to return to the stock
firmware simply by downloading it from D-Link and writing it to the
firmware partition.
# mtd -r write dap2610-firmware.bin firmware
Quirks
======
To be flashable from the D-Link http server, the firmware must be larger
then 6MB, and the size in the firmware header must match the actual file
size. Also, the boot loader verifies the checksum of the firmware before
each boot, thus the jffs2 must be after the checksum covered part. This
is solved in the factory image by having the rootfs at the very end of
the image (without pad-rootfs).
The sysupgrade image which does not have to be flashable from the D-Link
web UI may be smaller, and the checksum in the firmware header only
covers the kernel part of the image.
Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
[added WRGG Variables to DEVICE_VARS, squashed spi pinconf/mux,
added emd1's gmac0 config,fix dtc warnings]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware:
SOC: Qualcomm IPQ4018
RAM: 128 MB Nanya NT5CC64M16GP-DI
FLASH: 16 MB Macronix MX25L12805D
ETH: Qualcomm QCA8075 (4 Gigabit ports, 3xLAN, 1xWAN)
WLAN: Qualcomm IPQ4018 (2.4 & 5 Ghz)
BUTTON: Shared WPS/Reset button
LED: RGB Status/Power LED
SERIAL: Header J8 (UART, Left side of board). Numbered from
top to bottom:
(1) GND, (2) TX, (3) RX, (4) VCC (White triangle
next to it).
3.3v, 115200, 8N1
Tested/Working:
* Ethernet
* WiFi (2.4 and 5GHz)
* Status LED
* Reset Button (See note below)
Implementation notes:
* The shared WPS/Reset button is implemented as a Reset button
* I could not find a original firmware image to reverse engineer, meaning
currently it's not possible to flash OpenWrt through the Web GUI.
Installation (Through Serial console & TFTP):
1. Set your PC to fixed IP 192.168.1.12, Netmask 255.255.255.0, and connect to
one of the LAN ports
2. Rename the initramfs image to 'C0A8010B.img' and enable a TFTP server on
your pc, to serve the image
2. Connect to the router through serial (See connection properties above)
3. Hit a key during startup, to pause startup
4. type `setenv serverip 192.168.1.12`, to set the tftp server address
5. type `tftpboot`, to load the image from the laptop through tftp
6. type `bootm` to run the loaded image from memory
6. (If you want to return to stock firmware later, create an full MTD backup,
e.g. using instructions here https://openwrt.org/docs/guide-user/installation/generic.backup#create_full_mtd_backup)
7. Transfer the 'sysupgrade' OpenWrt firmware image from PC to router, e.g.:
`scp xxx-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/upgrade.bin`
8. Run sysupgrade to permanently install OpenWrt to flash: `sysupgrade -n /tmp/upgrade.bin`
Revert to stock:
To revert to stock, you need the MTD backup from step 6 above:
1. Unpack the MTD backup archive
2. Transfer the 'firmware' partition image to the router (e.g. mtd8_firmware.backup)
3. On the router, do `mtd write mtd8_firmware.backup firmware`
Signed-off-by: Tom Brouwer <tombrouwer@outlook.com>
[removed BOARD_NAME, OpenWRT->OpenWrt, changed LED device name to board name]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This target is still on kernel 4.9, and it looks like there is no
active maintainer for this target anymore.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The release notes since last time for wave-1:
* No changes to wave-1, but I make a version .014 copy anyway to keep
the makefile in sync.
The release notes since last time for wave-2:
* December 16, 2019: Wave-2 has a fix to make setting txpower work
better. Before setting the power was ignored at
least some of the time (it also appeared to work
mostly, so I guess it was being correctly set in
other ways).
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
This package contains nvram files for brcmfmac, a mac80211 driver for FullMAC
Cypress devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The release notes since last time for wave-1:
* November 29, 2019: Fix IBSS merge issue, related to TSF id leakage bug in firmware code.
Thanks for Ahmed Zaki @ Mage-Networks for helping to diagnose and test.
The release notes since last time for wave-2:
* December 6, 2019: Fix 160Mhz problem caused by logic that did not take into account the fact that
160Mhz has only 1/2 of the NSS of lower bandwidths in the rate table.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This backports a patch to build it work with python2 in addition to
python3.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Petr Štetiar <ynezz@true.cz>
The release notes since last time for wave-1:
* October 5, 2019: Fix too-short msg caused by invalid use of PayloadLen in receive path.
This appears to resolve the issue of getting (and ignoring) too-short commands
when we detect loss of CE interrupts and go into polling mode.
* October 12, 2019: Fix regression in IBSS mode that caused SWBA overrun issues. Related to
regression added during the ct-station logic, specifically TSF allocation.
Thanks for Ahmed Zaki @ Mage-Networks for helping to diagnose and test.
* October 15, 2019: Only send beacon tx completion events if we can detect CT driver is being
used (based on CT_STATS_OK flag being set). This should help CT firmware work
better on stock driver.
The release notes since last time for wave-2:
* October 15, 2019: Only send beacon tx completion events if we can detect CT driver is being
used (based on ATH10k_USE_TXCOMPL_TXRATE2 | ATH10k_USE_TXCOMPL_TXRATE1 flags being set).
This should help CT firmware work better on stock driver.
* October 31, 2019: Compile out peer-ratecode-list-event. ath10k driver ignores the event.
* November 1, 2019: Fix rate-ctrl related crash when nss and other things were changed while
station stays associated. See bug: https://github.com/greearb/ath10k-ct/issues/96
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This fixes frequent crashes observed on a UniFi AC Mesh using OpenWrt
master and 19.07. 18.06 seems not affected from our testing.
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit changes the source of the Wave 1 ath10k-firmware
from linux-firmware to Kall Valos ath10k-firmware repository.
This is necessary as the firmware selected in linux-firmware produces
frequent crashes in some circumstances.
This patch can be removed as soon as linux-firmware carries
10.2.4-1.0-00047 firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds packages for the Realtek RTl8822BE/RTL8822CE firmware
to be used with the rtw88 driver.
Signed-off-by: David Bauer <mail@david-bauer.net>
This enables a feature flag in the wave-2 firmware wmi-services indicating it can send
software-encrypted raw frames. This should in turn allow the AP-VLAN feature to work.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This should fix a problem with 1560 MTU, 160Mhz on DFS channels,
some other small issues on < 5.2 kernels, and for 5.2 driver,
it pulls in some upstream stable fixes.
wave-1 firmware changes since last update:
* June 24, 2019: Try allocating low-priority WMI msgs if high-prio are not available.
* June 24, 2019: Init rate-ctrl to start at lowest rate instead of in the middle. Hoping
this helps DHCP when station connects from a long distance.
wave-2:
* June 24, 2019 Start rate-ctrl at minimal values to help DHCP work better for far-away peers.
* July 24, 2019 Fix old regression that made /a (and probably /b/g) perform poorly, at least on
diet-compiled images.
* Aug 8, 2019 Improve a/b/g rate-ctrl by damping the PER swings caused by the all-or-nothing logic
of transmitting non-block-ack frames one at a time.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
iwlwifi from the new backports also supports more recent FW versions,
update to the most recent versions for already supported devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The BDFs for the:
ALFA Network AP120C-AC
ASUS Lyra
AVM FRITZ!Box 7530
AVM FRITZ!Repeater 3000
EnGenius EAP1300
EnGenius ENS620EXT
Netgear Orbi Pro SRK60
boards were upstreamed to the ath10k-firmware repository
and linux-firmware.git.
Furthermore the BDFs for the:
OpenMesh A42 specific BDFs
OpenMesh A62 specific BDFs
Linksys EA6350v3
have been updated.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
wireless-regdb fails to build if there is python2 installed from package
feeds, as staging_dir/hostpkg/bin/python is python2 and
staging_dir/hostpkg/bin takes precedence over staging_dir/host/bin
(proper place with python -> python3 symlink) which leads to the build
failure of wireless-regdb, so this patch makes it explicit which python
should be used.
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Russell Senior <russell@personaltelco.net>
Tested-by: Lucian Cristian <lucian.cristian@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fixes build issues on a python3 host (issues with the print statement
formatting in the current build).
Includes 100-regdb-write-firmware-file-format-version-code-20.patch and
other fixes.
Closes bugs.openwrt.org/index.php?do=details&task_id=1605.
Uses the tarball as requested.
Signed-off-by: Zachary Riedlshah <git@zacharyrs.me>
Python 2.7 will not be maintained past 2020. Let's convert
to python3 for rcw. Also drop byte swapping since TF-A had
been already used which handled byte swapping instead.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch updates the board-2.bin for the default
IPQ4019, QCA9984 and QCA9888 ath10k-firmware-xyz-ct
and -ct-htt firmwares.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
bnx2x driver support for the x86 architecture. Includes module and
firmware for Broadcom QLogic 5771x/578xx 10/20-Gigabit ethernet
adapters.
Signed-off-by: Petko Bordjukov <bordjukov@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added +kmod-lib-zlib-inflate as well]
wave-1:
2019-05-09: Tweak rate-ctrl: Ramp PER up faster, down slower. This
helps throughput in rate-vs-range test, especially with
nss1.
2019-05-20: Disable adaptive-CCA. I am not sure it helps, and it may
make it slower to detect noise that should tell the system
to stop transmitting. If someone has means to test this
properly, I'd be happy to work with them.
wave-2:
2019-05-15: Fix problem where rate-ctrl sometimes used rix of 0x0.
2019-05-15: Allow raw-tx of encrypted frame. Requires a patch to the
driver to use raw mode when skb has WEP flag enabled AND
skb is flagged to not be encrypted. Lightly tested.
2019-05-16: Fix tx-hang that happened when rate-ctrl chose an OFDM rate
for 20Mhz and sent that as AMPDU. To fix, limit to (V)HT
rates if peer is (V)HT. It seems that MCS0 (V)HT20 should
have as good of a chance of being detected as CCK or OFDM.
2019-06-06: Disable TX-BFEE, TX-BFER for IBSS connections. I suspect
this is part of the tx-hang issue seen with IBSS between
two 9984 radios.
2019-06-12: Fix rx-rate reporting in 'fw_stats' logic. This was at
least partly due to regressions I had added earlier when
working on some multi-vdev enhancements.
2019-6-12: Fix case where extd peer-stats were not always populated.
The stats gathering code did not handle error conditions
well.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This patch is to convert to use TF-A for firmware.
- Use un-swapped rcw since swapping will be done in TF-A.
- Use u-boot with TF-A defconfig.
- Rework memory map for TF-A introduction.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The Linksys EA8300 is based on QCA4019 and QCA9888 and provides three,
independent radios. NAND provides two, alternate kernel/firmware
images with fail-over provided by the OEM U-Boot.
Installation:
"Factory" images may be installed directly through the OEM GUI.
Hardware Highlights:
* IPQ4019 at 717 MHz (4 CPUs)
* 256 MB NAND (Winbond W29N02GV, 8-bit parallel)
* 256 MB RAM
* Three, fully-functional radios; `iw phy` reports (FCC/US, -CT):
* 2.4 GHz radio at 30 dBm
* 5 GHz radio on ch. 36-64 at 23 dBm
* 5 GHz radio on ch. 100-144 at 23 dBm (DFS), 149-165 at 30 dBm
#{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1
* All two-stream, MCS 0-9
* 4x GigE LAN, 1x GigE Internet Ethernet jacks with port lights
* USB3, single port on rear with LED
* WPS and reset buttons
* Four status lights on top
* Serial pads internal (unpopulated)
"Linksys Dallas WiFi AP router based on Qualcomm AP DK07.1-c1"
Implementation Notes:
The OEM flash layout is preserved at this time with 3 MB kernel and
~69 MB UBIFS for each firmware version. The sysdiag (1 MB) and
syscfg (56 MB) partitions are untouched, available as read-only.
Serial Connectivity:
Serial connectivity is *not* required to flash.
Serial may be accessed by opening the device and connecting
a 3.3-V adapter using 115200, 8n1. U-Boot access is good,
including the ability to load images over TFTP and
either run or flash them.
Looking at the top of the board, from the front of the unit,
J3 can be found on the right edge of the board, near the rear
|
J3 |
|-| |
|O| | (3.3V seen, open-circuit)
|O| | TXD
|O| | RXD
|O| |
|O| | GND
|-| |
|
Unimplemented:
* serial1 "ttyQHS0" (serial0 works as console)
* Bluetooth; Qualcomm CSR8811 (potentially conected to serial1)
Other Notes:
https://wikidevi.com/wiki/Linksys_EA8300 states
FCC docs also cover the Linksys EA8250. According to the
RF Test Report BT BR+EDR, "All models are identical except
for the EA8300 supports 256QAM and the EA8250 disable 256QAM."
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
This package provides board-specific reference ("cal") data
on an interim basis until included in the upstream distros
While originally conceived for IPQ4019-based boards, similar needs
are appearing with three-radio devices. For some of these devices,
both a board-2.bin file needs to be supplied both for the IPQ4019
as well as for the other radio on the board.
This patch allows new or multiple overrides to be specified by:
* Adding board name to ALLWIFIBOARDS
* Placing file(s) in this directory named as
board-<devicename>.<qca4019|qca9888|qca9984>
* Adding
$(eval $(call generate-ipq-wifi-package,<device>,<display name>))
(along with suitable package selection for the board)
At this time, QCA4019, QCA9888, and QCA9984 are supported.
Extension to other chips should be straightforward.
The existing files, board-*.bin, are "grandfathered" as QCA4019.
The package name has been retained for compatability reasons.
At this time it DEPENDS:=@TARGET_ipq40xx, limiting its visibility.
Build-tested-on: asus_map-ac2200, alfa-network_ap120c-ac,
avm_fritzbox-7530, avm_fritzrepeater-3000, engenius_eap1300,
engenius_ens620ext, linksys_ea6350v3, qxwlan-e2600ac-c1/-c2
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Update linux-firmware to 20190416, which includes updated firmwares e.g. for ath10k
Also switch to official tarball source.
The following firmware files we use are updated in this change:
ath10k/QCA6174/hw3.0/board-2.bin
ath10k/QCA9888/hw2.0/firmware-5.bin
ath10k/QCA988X/hw2.0/firmware-5.bin
ath10k/QCA9984/hw1.0/firmware-5.bin
mrvl/sd8887_uapsta.bin
mrvl/pcie8897_uapsta.bin
iwlwifi-8000C-36.ucode
iwlwifi-8265-36.ucode
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Release notes since last time:
Release notes for wave-1:
2019-04-02: Support some get/set API for eeprom rate power tables.
Mostly backported from 10.2
2019-04-02: Support adaptive-CCA, backported from 10.2
2019-04-02: Support adding eeprom configAddr pairs via the
set-special API. These configAddrs can be used to change
the default register settings for up to 12 registers.
2019-05-03: Fix tx-power settings for 2x2, 3x3 rates.
Original logic I put in back in 2016 set 2x2 and 3x3 lower
than the needed to be when using most NICs (very high
powered NICs would not have been affected I think, not sure
any of those exist though.)
This improves throughput for 2x2 and 3x3 devices,
especially when the signal is weaker.
Release notes for wave-2:
2019-04-08: When setting keys, if high bit of high value of
key_rsc_counter is set to 0x1, then the lower 48 bits will
be used as the PN value. By default, PN is set to 1 each
time the key is set.
2019-04-08: Pack PN into un-used 'excretries' aka
'num_pkt_loss_excess_retry' high 16 bits.
This lets us report peer PN, but *only* if driver has
previously set a PN when setting key (or set-special cmd is
used to enable PN reporting).
This is done so that we know the driver is recent
enough to deal with the PN stat reporting.
2019-04-16: Support specifying tx rate on a per-beacon packet.
See ath10k_wmi_op_gen_beacon_dma and
ath10k_convert_hw_rate_to_rate_info for API details.
Driver needs additional work to actually enable this
feature currently.
2019-04-30: Compile out tx-prefetch caching logic.
It is full of tricky bugs that cause tx hangs.
I fixed at least one, but more remain and I have wasted too
much time on this already.
2019-05-08: Start rate-ctrl at mcs-3 instead of mcs-5.
This significantly helps DHCP happen quickly, probably
because the initial rate being too high would take a while
to ramp down, especially since there are few packets sent
by the time DHCP needs to start.
This bug was triggered by me decreasing retries of 0x1e
(upstream default) to 0x4. But, I think it is better to
start with lower initial MCS instead of always having a
very high retry count.
Tested on 8devices Jalapeno dev board(IPQ4019)
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [neatify]
Release notes since last time:
Release notes for wave-1 / 10.1:
2019-03-28: Fix sometimes using bad TID for management frames
in htt-mgt mode. (Backported from wave2, looks
like bug would be the same though.)
Release notes for wave-2 / 10.4:
2019-03-28: Fix off-channel scanning while associated in
proxy-station mode.
2019-03-29: Fix sometimes sending mgt frames on wrong tid when
using htt-mgt. This bug has been around since I first
enabled htt-mgt mode.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Release notes since last time:
Release notes for wave-1:
- 2019-03-12: Add btcoex feature flag for 2.4Ghz only adapters,
backported from upstream 10.2 firmware.
- 2019-03-12: Support offloading decrypt of PMF blockack frames
to the host. This lets us do blockack with PMF and
rx-sw-crypt. Normal hwcrypt scenarios would not need this.
Release notes for wave-2:
- 2019-03-12: Fix crash when tearing down VI TID when pending frames
exist. Could reproduce this while doing rmmod when VI
traffic was flowing and PMF was enabled but broken.
Bad luck could rarely cause it to happen in more normal
config too.
- 2019-03-12: Support offloading decrypt of PMF blockack frames to
the host. This lets us do blockack with PMF and
rx-sw-crypt. Normal hwcrypt scenarios would not need this.
- 2019-03-12: Re-work problematic patch that attempted to fix transmit
on non-QOS tids. It appears buggy in several ways,
hopefully improved now. This was introduced last fall.
See github bug 78.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware
--------
CPU: Qualcomm IPQ4018
RAM: 256M
FLASH: 32M SPI NOR W25Q256
ETH: QCA8075
WiFi2: IPQ4018 2T2R 2SS b/g/n
WiFi5: IPQ4018 2T2R 2SS n/ac
LED: - Power amber
- LAN1(PoE) green
- LAN2 green
- Wi-Fi 2.4GHz green
- Wi-Fi 5GHz green
BTN: - WPS
UART: 115200n8 3.3V J1
VCC(1) - GND(2) - TX(3) - RX(4)
Added basic support to get the device up and running for a sysupgrade
image only.
There is currently no way back to factory firmware, so this is a one-way
street to OpenWRT.
Install from factory condition is convoluted, and may brick your device:
1) Enable SSH and disable the CLI on the factory device from the web user
interface (Management->Advanced)
2) Reboot the device
3) Override the default, limited SSH shell:
a) Get into the ssh shell:
ssh admin@192.168.1.1 /bin/sh --login
b) Change the dropbear script to disable the limited shell. At the
empty command prompt type:
sed -i '/login_ssh/s/^/#/g’ dropbear
/etc/init.d/dropbear restart
exit
4) ssh in to a (now-) normal OpenWRT SSH session
5) Flash your built image
a) scp openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin
admin@192.168.1.1:/tmp/
b) ssh admin@192.168.1.1
c) sysupgrade -n
/tmp/openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin
6) After flash completes (it may say "Upgrade failed" followed by
"Upgrade completed") and device reboots, log in to newly flashed
system. Note you will now need to ssh as root rather than admin.
Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
[whitespace fixes, reordered partitions, removed rng node from 4.14,
fixed 901-arm-boot-add-dts-files.patch]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware
--------
CPU: Qualcomm IPQ4019
RAM: 256M (NANYA NT5CC128M16JR-EK)
FLASH: 128M NAND (Macronix MX30LF1G18AC-XKI)
ETH: Qualcomm QCA8072
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
WiFi5: QCA9984 4T4R 4SS n/ac
LED: - Connect green/blue/red
- Power green
BTN: WPS/Connect
UART: 115200n8 3.3V
VCC - RX - TX - GND (Square is VCC)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz3000'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ3000.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz3000.bin uboot0
> mtd write /path/to/uboot-fritz3000.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
Add specific 'variant' for 'bus=ahb,bmi-chip-id=0,bmi-board-id=25' BDF.
Use the same value ('ALFA-Network-AP120C-AC') as sent upstream.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Release notes since last update:
wave-1 firmware:
* Feb 14, 2019: Remove logic that causes assert when swba logic is not
initialized. This was seen when trying to bring up 6 VAP
vdevs. A similar fix went into wave-2 firmware some time
ago.
* Feb 27, 2019: Support up to 32 vAP vdevs, fix stack corruption when
driver requests too many vAP.
* Feb 28, 2019: Support beacon-tx-wmi callback message. This lets driver
properly clean up beacon buffers so we don't crash
(somethings the entire OS/system) due to DMA errors.
wave-2 firmware:
* Feb 27. 2019: Support up to 32 AP vdevs. Previous to this, stack would
be corrupted if you went past 16 AP vdevs.
* Feb 28, 2019: Support beacon-tx-wmi callback message. This lets driver
properly clean up beacon buffers. In wave-1, this could
crash the entire OS, but I didn't see the same crashes
in wave-2, so maybe it is fixed in some other way. Add
the feature regardless as it seems proper.
Signed-off-by: Michael Yartys <michael.yartys@gmail.com>
Hardware
--------
CPU: Qualcomm IPQ4019
RAM: 256M
FLASH: 128M NAND
ETH: QCA8075
VDSL: Intel/Lantiq VRX518 PCIe attached
currently not supported
DECT: Dialog SC14448
currently not supported
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
LED: - Power/DSL green
- WLAN green
- FON/DECT green
- Connect/WPS green
- Info green
- Info red
BTN: - WLAN
- FON
- WPS/Connect
UART: 115200n8 3.3V (located under the Dialog chip)
VCC - RX - TX - GND (Square is VCC)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz7530'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ7530.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz7530.bin uboot0
> mtd write /path/to/uboot-fritz7530.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
[removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Qxwlan E2600AC C1 based on IPQ4019
Specifications:
SOC: Qualcomm IPQ4019
DRAM: 256 MiB
FLASH: 32 MiB Winbond W25Q256
ETH: Qualcomm QCA8075
WLAN: 5G + 5G/2.4G
* 2T2R 2.4/5 GHz
- QCA4019 hw1.0 (SoC)
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
INPUT: Reset buutton
LED: 1x Power ,6 driven by gpio
SERIAL: UART (J5)
UUSB: USB3.0
POWER: 1x DC jack for main power input (9-24 V)
SLOT: Pcie (J25), sim card (J11), SD card (J51)
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Qxwlan E2600AC C2 based on IPQ4019
Specifications:
SOC: Qualcomm IPQ4019
DRAM: 256 MiB
NOR: 16 MiB Winbond W25Q128
NAND: 128MiB Micron MT29F1G08ABAEAWP
ETH: Qualcomm QCA8075
WLAN: 5G + 5G/2.4G
* 2T2R 2.4/5 GHz
- QCA4019 hw1.0 (SoC)
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
INPUT: Reset buutton
LED: 1x Power, 6 driven by gpio
SERIAL: UART (J5)
USB: USB3.0
POWER: 1x DC jack for main power input (9-24 V)
SLOT: Pcie (J25), sim card (J11), SD card (J51)
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "ubi" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[ added rng node. whitespace fixes, ported 02_network,
ipq-wifi Makefile, misc dts fixes, trivial message changes ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit updates the file "board-linksys_ea6359v3".
Without this commit, the Linksys EA6350v3 will experience poor wireless
performance in both bands. With this patch, wireless performace will be
comparable to the performance of the stock firmware.
Signed-off-by: Oever González <notengobattery@gmail.com>
The board-files are specific to the target and device. Hence
they need to be set as nonshared. Otherwise they do not show
up on the package repository. This causes problems for
imagebuilder, if it needs to build a image for a specific
device that hasn't had the time to have get its boardfile
upstream.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
SoC: Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores
RAM: 256 MiB (Nanya NT5CC128M16IP-DI)
FLASH: 128 MiB (Macronix NAND)
WiFi0: Qualcomm IPQ4019 b/g/n 2x2
WiFi1: Qualcomm IPQ4019 a/n/ac 2x2
WiFi2: Qualcomm Atheros QCA9886 a/n/ac
BT: Atheros AR3012
IN: WPS Button, Reset Button
OUT: RGB-LED via TI LP5523 9-channel Controller
UART: Front of Device - 115200 N-8
Pinout 3.3v - RX - TX - GND (Square is VCC)
Installation:
1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp.
Login credentials are identical to the Web UI.
2. Login to the device via SSH.
3. Flash the initramfs image using
> mtd-write -d linux -i openwrt-image-file
4. Power-cycle the device and wait for OpenWRT to boot.
5. From there flash the OpenWRT-sysupgrade image.
Ethernet-Ports: Although labeled identically, the port next to
the power socket is the LAN port and the other one is WAN. This
is the same behavior as in the stock firmware.
Signed-off-by: Marius Genheimer <mail@f0wl.cc>
[Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh,
reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79,
minor dts touchup, added rng to 4.19 dts]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Release notes since last time:
2019-02-08:
Fix rate-ctrl assert related to bad logic that tried to guess
that lower bandwidth probes were automatically successful if
higher was. The NSS mismatch that can happen here caused the
assert. Just comment out the offending code
(per comment from original QCA code). This is bug 69.
2019-02-10:
Fix bssid mis-alignment that broke 4-addr vlan mode (bug 67).
Original buggy commit was
commit 2bf89e70ecd1 ("dev-ds: Better packing of wal_vdev struct.")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* Jan 2, 2019
Rebase patches to make 9980 bisectable.
* Jan 2, 2019
Fix scheduling related assert when wal-peer is deleted with pending
tx buffers (bug 54, and others)
* Jan 7, 2019:
Fix specifying retransmits for AMPDU frames. It was previously ignored
since it is a 'software' retransmit instead of a hardware retransmit.
* Jan 9, 2019
Fix potential way to get zero rates selected (and then assert)
* Jan 18, 2019
pfsched has specific work-around to just return if we find invalid flags AND
if we are in an out-of-order situation. Maybe this is last of the pfsched
related issues (bug 54 and similar).
* Jan 24, 2019
The rcSibUpdate method can be called concurrently with IRQ tx-completion callback,
and that could potentially allow the tx-completion callback to see invalid state
and assert or otherwise mess up the rate-ctrl logic. So, disable IRQs in
rcSibUpdate to prevent this. Related to bug 58.
* Jan 28, 2019
Ensure that cached config is applied to ratectrl objects when fetched from
the cache. This should fix part of bug 58.
* Jan 28, 2019
Ensure that ratectrl objects from cachemgr are always initialized. This fixes
another part of bug 58.
* Jan 30, 2019
Better use of temporary rate-ctrl object. Make sure it is initialized, simplify
code path. This finishes up porting forward similar changes I made for wave-1
firmware long ago, and fixes another potential way to hit bug-58 issues.
* Jan 30, 2019
Cachemgr did not have a callback for when memory was logically freed. This means
that peers could keep stale references to rate-ctrl objects that were in process
of being DMA'd into to load a different peer's rate-ctrl state. This was causing
the bugcheck logic to fail early and often, and I suspect it might be a root cause
of bug 58 as well. The fix is to add a callback and set any 'deleted' memory references
to NULL so that we cannot access it accidentally. Thanks to excellent logs and patience
from the bug-58 reporter!
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This commit adds support for the Linksys EA6350v3 device in the ipq-wifi
target.
Without this patch, the Linksys EA6350v3 won't be hable to have fully
functional wireless interfaces. This is not permanent: the board data has
already been sent to ath10k _at_ lists _dot_ infradead _dot_ org
Signed-off-by: Ryan Pannell <ryan@osukl.com>
Signed-off-by: Oever González <notengobattery@gmail.com>
This now matches what was generated locally on my PC and the file on the
mirror server.
Fixes: 575d0240f9 ("ath10k-firmware: update board-2.bin for community firmwares")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button
LEDS: Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz
1. Load Ramdisk via U-Boot
To set up the flash memory environment, do the following:
a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters:
* 115200bps
* 8N1
b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown.
U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm
2. Load image via GUI
a. Upgrade EAP1300 to FW v3.5.3.2
In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade.
b. Transfer to OpenWrt from EnGenius.
In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin.
3. Revert to EnGenius EAP1300
To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration.
$ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin
Signed-off-by: Steven Lin <steven.lin@senao.com>
It is not necessary to have iucode-tool present on target system to have
functional intel-microcode package. The build time dependency is kept.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The BDFs for all boards were upstreamed to the ath10k-firmware
repository and linux-firmware.git.
We switched to the upstream board-2.bin, hence the files can be removed
here.
Keep the ipq-wifi package in case new boards are added. It might take
some time till board-2.bins send upstream are merged.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch updates the board-2.bin for the default
IPQ4019, QCA9984 and QCA9888 ath10k-firmware-xyz-ct
and -ct-htt firmwares.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Add the most recent supported firmware file for the Intel 9000 and
9260 wireless chips. The API version 41 is not yet supported by the driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Kalles ath10k PR was finally merged so update linux-firmware to
include those changes.
This is needed since disabling ath10k-firmware a lot of custom BDF-s
in board-2.bin-s are not available in previously outdated linux-firmware
board-2.bin-s.
This also includes support for boards currently using ipq-wifi and other
WIP ones.
Runtime tested on 8devices Jalapeno.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Building ls-dpl package requires the dtc tool. This patch
is to support using linux dtc tool for ls-dpl package.
This avoids compile issue when host system doesn't have
the dtc tool.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
ls1012afrdm was no longer supported in NXP Layerscape SDK.
Instead a new board ls1012afrwy was introduced in LSDK.
This patch is to drop ls1012afrdm and add ls1012afrwy support.
Since only 2MB NOR flash could be used, we just put u-boot
and firmware on NOR flash, and put kernel/dtb/rootfs on SD
card.
The Layerscape FRWY-LS1012A board is an ultra-low-cost
development platform for LS1012A Series Communication
Processors built on Arm Cortex-A53. This tool refines the
FRDM-LS1012A with more features for a better hands-on experience
for IoT, edge computing, and various advanced embedded
applications. Features include easy access to processor I/O,
low-power operation, micro SD card storage, an M2 connector, a
small form factor, and expansion board options via mikroBUS Click
Module. The MicroBUS Module provides easy expansion via hundreds
of powerful modules supporting sensors, actuators, memories,
and displays.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
NOR/QSPI Flash on Layerscape board only has limited 64MB memory size.
Since some boards (ls1043ardb/ls1046ardb/ls1088ardb/ls1021atwr)
could support SD card boot, we added SD boot support for them to put
all things on SD card to meet large memory requirement.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The NXP TWR-LS1021A module is a development system based
on the QorIQ LS1021A processor.
- This feature-rich, high-performance processor module can
be used standalone or as part of an assembled Tower System
development platform.
- Incorporating dual Arm Cortex-A7 cores running up to 1 GHz,
the TWR-LS1021A delivers an outstanding level of performance.
- The TWR-LS1021A offers HDMI, SATA3 and USB3 connectors as
well as a complete Linux software developer's package.
- The module provides a comprehensive level of security that
includes support for secure boot, Trust Architecture and
tamper detection in both standby and active power modes,
safeguarding the device from manufacture to deployment.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to update ls-ppa to LSDK-18.06 release
and to rework ls-ppa makefile to make it more readable.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The rcw source code had been migrated to codeaurora
for LSDK-18.06 release and the future release. The
source code had also involved ls1012ardb/ls1012afrdm/
ls1088ardb/ls2088ardb rcw, so we updated ls-rcw to
LSDK-18.06, reworked the makefile and dropped ls-rcw-bin
package in this patch. Also reworked ls-rcw patch to
adapt to the latest source code.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The dpl-examples source code had been migrated to
codeaurora for LSDK-18.06 release and the future
release. This patch is to update this package to
LSDK-18.06.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Actually there was no change for fman-ucode in LSDK-18.06
just tagged with LSDK-18.06. This patch is to rework the
fman-ucode makefile to make it more readable, and to use
lsdk-1806 as the PKG_VERSION.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
