Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration
data from the nvmem subsystem.
This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.
wmac's nodes are also changed over to use nvmem-cells over OpenWrt's
custom mtd-cal-data property.
The wifi mac address remains correct after these changes, because When both
"mac-address" and "calibration" are defined, the effective mac address
comes from the cell corresponding to "mac-address" and
mac-address-increment.
Test passed on my tplink tl-wdr4310.
Signed-off-by: Edward Chow <equu@openmail.cc>
The uart node is enabled on all devices except one (GL-USB150 *).
Thus, let's not have a few hundred nodes to enable it, but do not
disable it in the first place.
Where the majority of devices is using it, also move the serial0
alias to the DTSI.
*) Since GL-USB150 even defines serial0 alias, the missing uart
is probably just a mistake. Anyway, disable it for now so this
patch stays cosmetic.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
None of the spi drivers on ath79 uses the num-cs property.
Cc: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Chuanhong Guo <gch981213@gmail.com>
Currently, we request LED labels in OpenWrt to follow the scheme
modelname:color:function
However, specifying the modelname at the beginning is actually
entirely useless for the devices we support in OpenWrt. On the
contrary, having this part actually introduces inconvenience in
several aspects:
- We need to ensure/check consistency with the DTS compatible
- We have various exceptions where not the model name is used,
but the vendor name (like tp-link), which is hard to track
and justify even for core-developers
- Having model-based components will not allow to share
identical LED definitions in DTSI files
- The inconsistency in what's used for the model part complicates
several scripts, e.g. board.d/01_leds or LED migrations from
ar71xx where this was even more messy
Apart from our needs, upstream has deprecated the label property
entirely and introduced new properties to specify color and
function properties separately. However, the implementation does
not appear to be ready and probably won't become ready and/or
match our requirements in the foreseeable future.
However, the limitation of generic LEDs to color and function
properties follows the same idea pointed out above. Generic LEDs
will get names like "green:status" or "red:indicator" then, and
if a "devicename" is prepended, it will be the one of an internal
device, like "phy1:amber:status".
With this patch, we move into the same direction, and just drop
the boardname from the LED labels. This allows to consolidate
a few definitions in DTSI files (will be much more on ramips),
and to drop a few migrations compared to ar71xx that just changed
the boardname. But mainly, it will liberate us from a completely
useless subject to take care of for device support review and
maintenance.
To also drop the boardname from existing configurations, a simple
migration routine is added unconditionally.
Although this seems unfamiliar at first look, a quick check in kernel
for the arm/arm64 dts files revealed that while 1033 lines have
labels with three parts *:*:*, still 284 actually use a two-part
labelling *:*, and thus is also acceptable and not even rare there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The "/dts-v1/;" identifier is supposed to be present once at the
top of a device tree file after the includes have been processed.
In ath79, we therefore requested to have in the DTS files so far,
and omit it in the DTSI files. However, essentially the syntax of
the parent ath79.dtsi file already determines the DTS version, so
putting it into the DTS files is just a useless repetition.
Consequently, this patch puts the dts-v1 statement into the parent
ath79.dtsi, which is (indirectly) included by all DTS files. All
other occurences are removed.
Since the dts-v1 statement needs to be before any other definitions,
this also moves the includes to make sure the ath79.dtsi or its
descendants are always included first.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
SPI Flash chip supports up to 33 MHz wihout fast read opcode.
Available frequencies are 112.5, 56.25, 37.5, 28.125, 22.5 etc.
This patch increases the nominal maximum frequency to 33 MHz,
reaching an effective increase from 22.5 to 28.125 MHz.
Formula to calculate SPI frequency:
Freq = 225 MHz / 2 / div
Before:
$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real 0m 3.58s
user 0m 0.00s
sys 0m 3.57s
After:
$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real 0m 2.95s
user 0m 0.00s
sys 0m 2.93s
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This applies several style adjustments that have been requested in
recent reviews to older DTS files. Despite making the code base more
consistent, this will also help to reduce review time when DTSes
are copy/pasted.
Applied changes:
- Rename gpio-keys/gpio-leds to keys/leds
- Remove node labels that are not used
- Use label property for partitions
- Prefix led node labels with "led_"
- Remove redundant includes
- Harmonize new lines after status property
- Several smaller style fixes
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware:
SoC: AR9344
CPU: 560 MHz
Flash: 8 MiB
RAM: 128 MiB
WiFi: Atheros AR9340 2.4GHz 802.11bgn
Atheros AR9300 5GHz 802.11an
Ethernet: AR934X built-in switch, WAN on separate physical interface
USB: 1x 2.0
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to
wdr3500v1_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[removed stray newline]
Signed-off-by: David Bauer <mail@david-bauer.net>
