Kernel interface changed with kernel 4.19, it does not accept raw GPIO
numbers any more. Deactivate these drivers on kernel 4.19 for now.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The r8169 driver uses the phy lib with the realtek phy driver in kernel
4.19 instead of integrating the phy driver into the mac driver.
Add the new phy driver and add this missing dependency.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This makes the patches which were just copied in the previous commit
apply on top of kernel 4.19.
The patches in the backports-4.19 folder were checked if they are really
in kernel 4.19 based on the title and only removed if they were found in
the upstream kernel.
The following additional patches form the pending folder went into
upstream Linux 4.19:
pending-4.19/171-usb-dwc2-Fix-inefficient-copy-of-unaligned-buffers.patch
pending-4.19/190-2-5-e1000e-Fix-wrong-comment-related-to-link-detection.patch
pending-4.19/478-mtd-spi-nor-Add-support-for-XM25QH64A-and-XM25QH128A.patch
pending-4.19/479-mtd-spi-nor-add-eon-en25qh32.patch
pending-4.19/950-tty-serial-exar-generalize-rs485-setup.patch
pending-4.19/340-MIPS-mm-remove-mips_dma_mapping_error.patch
Bigger changes were introduced to the m25p80 spi nor driver, as far as I
saw it in the new code, it now has the functionality provided in this
patch:
pending-4.19/450-mtd-m25p80-allow-fallback-from-spi_flash_read-to-reg.patch
Part of this patch went upstream independent of OpenWrt:
hack-4.19/220-gc_sections.patch
This patch was reworked to match the changes done upstream.
The MIPS DMA API changed a lot, this patch was rewritten to match the
new DMA handling:
pending-4.19/341-MIPS-mm-remove-no-op-dma_map_ops-where-possible.patch
I did bigger manual changes to the following patches and I am not 100% sure if they are all correct:
pending-4.19/0931-w1-gpio-fix-problem-with-platfom-data-in-w1-gpio.patch
pending-4.19/411-mtd-partial_eraseblock_write.patch
pending-4.19/600-netfilter_conntrack_flush.patch
pending-4.19/611-netfilter_match_bypass_default_table.patch
pending-4.19/670-ipv6-allow-rejecting-with-source-address-failed-policy.patch
hack-4.19/211-host_tools_portability.patch
hack-4.19/221-module_exports.patch
hack-4.19/321-powerpc_crtsavres_prereq.patch
hack-4.19/902-debloat_proc.patch
This is based on patchset from Marko Ratkaj <marko.ratkaj@sartura.hr>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This just copies the files from the kernel 4.14 specific folders into
the kernel 4.19 specific folder, no changes are done to the files in
this commit.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The b53 driver was added as a dsa driver into the mainline Linux kernel,
but we still use the swconfig based driver. The header file b53.h is
used by both drivers, but the swconfig one needs an extra member, add
this one in a patch to not overwrite the version shipped with the
mainline kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ledtrig-netdev was added to upstream Linux kernel 4.16, replace our
own version with the patch based on the upstream version.
This will remove the ledtrig-netdev support from kernel 3.18, because I
not want to spend time on backporting it to 3.18. This will make it
easier to use the upstream version with kernel 4.19, by just not
applying this patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
63843750 Update manual pages
27801e98 Bump up version number to 1.35.1
60e020a8 nghttpx: Fix broken trailing slash handling
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The above options were incorrectly changed to required tags. Make them
optional again.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
f6d0e8c36f Fix rwlock stall with PREFER_WRITER_NONRECURSIVE_NP (bug 23861)
2794474c65 powerpc: Add missing CFI register information (bug #23614)
d8ca7a0c71 Fix _dl_profile_fixup data-dependency issue (Bug 23690)
f1e211096b inet/tst-if_index-long: New test case for CVE-2018-19591 [BZ #23927]
4e9f34e54f support: Implement <support/descriptors.h> to track file descriptors
e75481a7a7 support: Close original descriptors in support_capture_subprocess
0f79dc0be3 support_quote_string: Do not use str parameter name
6b2dd53aa0 support: Implement support_quote_string
50477165b9 malloc: Add another test for tcache double free check.
4b246928bd malloc: tcache double free check
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Backport upstream patch fixing incorrect passing of -lxtables to
LDFLAGS instead of LDLIBS in the tc/Makefile
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This updates the backports package used in mac80211 to version 4.19.7-1
which is based on kernel 4.19.7. This integrates all the stable fixes
introduces in this kernel version.
The deleted patches are not needed any more because they are either
included in the upstream Linux kernel 4.19.7 or in backports 4.19.7-1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It's no longer needed as all mt7621 devices use DT binding (supported by
upstream mtd code) for specifying "firmware" part format explicitly.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
In hack/904-debloat_dma_buf.patch, DMA_SHARED_BUFFER is changed from
bool to tristate. As this patch is not applied to external kernel
sources, build fails if kmod-dma-buf is enabled. Fix this by only
including the module file if CONFIG_EXTERNAL_KERNEL_TREE and
CONFIG_KERNEL_GIT_CLONE_URI are not enabled.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
3aa81d0 file: access exec timeout via daemon ops structure
7235f34 plugin: store pointer to exec timeout value in the ops structure
ccd7c0a treewide: rename exec_timeout to rpc_exec_timeout
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
During upstream removal of conditional ipv6 support an order swap error
was made in a ternary operator usage.
This patch sent upstream.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The argument to print_0xhex is converted to unsigned long long
so the format string give for normal printout has to be some
variant of %llx. Backport the patch as otherwise, bogus values
will be printed on 32 bit platforms.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This partitialy reverts commit ccab68f2d3.
Registering the GPIO chip without a parent device completely breaks the
ath9k GPIOs for device tree targets.
As long as boards using the devicetree don't have the gpio-controller
property set for the ath9k node, the unloading of the driver works as
expected.
Register the GPIO chip with the ath9k device as parent only for OF
targets to find a trade-off between the needs of driver developers and
the broken LEDs and buttons seen by users.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The qca9557/qca956x reset-controller aren't a simple bus. A simple bus
would require node unit addresses.
Add the node unit addresses for the qca9557 usb phys. Add the regs for
the USB_PWRCTL and USB_CONFIG registers even not yet used.
Fix the wrong ar7100 pcie controller node unit address as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to the enforced image metadata we ensure that the correct image is
uploaded. Checks based on a magic arn't required any more.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Beside one exception, no one took care of these two remaining boards
still using the legacy image build code during the last two years.
Since OpenWrt 14.07 the ALLNET ALL0239-3G image building is broken.
The Sitecom WL-341 v3 image build code looks pretty hackish and broken.
It's questionable if the legacy image works as all.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Drop the factory images and the firmware tool to create them. They don't
work any more, since the factory image has an uImage header covering the
whole kernel + rootfs. This way the uImage splitter will not be able to
find the rootfs and the kernel will panic later on.
The factory images were most likely added at a time the board had
distinct partitions for kernel and rootfs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Support other packages using pkg-config to query existence and details of
libelf and libdw libraries at build time.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
similar to hostapd, also add a ubus interface for wpa_supplicant
which will allow handling WPS push-button just as it works for hostapd.
In order to have wpa_supplicant running without any network
configuration (so you can use it to retrieve credentials via WPS),
configure wifi-iface in /etc/config/wireless:
config wifi-iface 'default_radio0'
option device 'radio0'
option network 'wwan'
option mode 'sta'
option encryption 'wps'
This section will automatically be edited if credentials have
successfully been acquired via WPS.
Size difference (mips_24kc): roughly +4kb for the 'full' variants of
wpa_supplicant and wpad which do support WPS.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch updates the uboot-fritz4040 package to the latest version.
The portability and private-libgcc patches, as well as the
upload-to-f4040.sh script have been added to the upstream repository.
Furthermore, the upload-to-f4040 has been updated to take the first
parameter as the file it is supposed to flash, otherwise it defaults
to the previous "uboot-fritz4040.bin". Furthermore the error messages
have been improved and ftp will now dump some "progress information"
to the user's console.
Also included is support for gcc 8+ and a fix for the obnoxous error
that currently breaks the builders:
| fritz/src/lzma2eva.c:23:30: fatal error: zlib.h: No such file or directory
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Fix the imagetag on the HG655b to allow a correct partition detection at boot time.
It turns out that it was defined at the wrong partition. Just move the imagetag to
the linux firmware partition.
The bug is present since the 18.06 release. Without this fix, the board won't boot.
Fixes: a27d59bb42 ("brcm63xx: switch to new partition layout specification")
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The reset mask for the bcm6368 switch core was left at 0 due to a copy &
paste error. Fix this by setting it to the correct value.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Remove the sky.mk causing a duplicate device profile to be added in
image builder. The generic device code already generates a profile for
the device.
Fixes FS#1780.
Fixes: d591260407 ("brcm63xx: initial support for Sky SR102 router")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Buildbot revealed some subtargets are still missing the new symbol.
Fixes: dfbf836a52 ("kernel: bump 4.9 to 4.9.143")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Backport upstream commits. Most interesting 122392e which changes how
SERVFAIL is handled especially in event of genuine server down/failure
scenarios with multiple servers. a799ca0 also interesting in that
answered received via TCP are now cached, DNSSEC typically using TCP
meant until now answers weren't cached, hence reducing performance.
59e4703 Free config file values on parsing errors.
48d12f1 Remove the NO_FORK compile-time option, and support for uclinux.
122392e Revert 68f6312d4bae30b78daafcd6f51dc441b8685b1e
3a5a84c Fix Makefile lines generating UBUS linker config.
24b8760 Do not rely on dead code elimination, use array instead. Make options bits derived from size and count. Use size of option bits and last supported bit in computation. No new change would be required when new options are added. Just change OPT_LAST constant.
6f7812d Fix spurious AD flags in some DNS replies from local config.
cbb5b17 Fix logging in cf5984367bc6a949e3803a576512c5a7bc48ebab
cf59843 Don't forward *.bind/*.server queries upstream
ee87504 Remove ability to compile without IPv6 support.
a220545 Ensure that AD bit is reset on answers from --address=/<domain>/<address>.
a799ca0 Impove cache behaviour for TCP connections.
Along with an additional patch to fix compilation without DHCPv6, sent
upstream.
I've been running this for aaaages without obvious issue hence brave
step of opening to wider openwrt community.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This reverts commit a6a8fe0be5.
buildbot found an error
option.c: In function 'dhcp_context_free':
option.c:1042:15: error: 'struct dhcp_context' has no member named 'template_interface'
free(ctx->template_interface);
revert for the moment
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Backport upstream commits. Most interesting 122392e which changes how
SERVFAIL is handled especially in event of genuine server down/failure
scenarios with multiple servers. a799ca0 also interesting in that
answered received via TCP are now cached, DNSSEC typically using TCP
meant until now answers weren't cached, hence reducing performance.
59e4703 Free config file values on parsing errors.
48d12f1 Remove the NO_FORK compile-time option, and support for uclinux.
122392e Revert 68f6312d4bae30b78daafcd6f51dc441b8685b1e
3a5a84c Fix Makefile lines generating UBUS linker config.
24b8760 Do not rely on dead code elimination, use array instead. Make options bits derived from size and count. Use size of option bits and last supported bit in computation. No new change would be required when new options are added. Just change OPT_LAST constant.
6f7812d Fix spurious AD flags in some DNS replies from local config.
cbb5b17 Fix logging in cf5984367bc6a949e3803a576512c5a7bc48ebab
cf59843 Don't forward *.bind/*.server queries upstream
ee87504 Remove ability to compile without IPv6 support.
a220545 Ensure that AD bit is reset on answers from --address=/<domain>/<address>.
a799ca0 Impove cache behaviour for TCP connections.
I've been running this for aaaages without obvious issue hence brave
step of opening to wider openwrt community.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Openwrt no longer uses and has not used since 5acfe55d71 Jun 2016 the
timestamp file (/etc/dnsmasq.time) method of resolving the dnssec/ntp
dnslookup chicken/egg problem, having used signals from ntp since that
change.
Drop the 'dnssec-improve-timestamp-heuristic' patch since it is neither
used nor sent upstream. One less thing to refresh & maintain.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
