This fixes the build of the gemini and the apm821xx target.
The e2fsck application returns an error code now and that makes the
build fail. The tune2fs command adds an extra option and the e2fsck
should later fix the file system. It is intentionally broken in this
place.
e2fsprogs was patched before to ignore this error.
Fixes: 95e4664b5e ("tools: e2fsprogs: drop e2fsck patch")
Link: https://github.com/openwrt/openwrt/pull/16607
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The one for the mx60 was wrong. The LAN MAC is offset by one.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14037
Signed-off-by: Robert Marko <robimarko@gmail.com>
The qca8k driver is upstream, unlike swconfig. This applies to the mx60
and wndr4700 only. Fixed up LED definitions as well.
RTL83xx DSA for WNDAP62300/660 is not working.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14037
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use realtek,extif property instead of realtek,extif0 to extif2
by extending it with the cpu_port parameter.
The extif number is automatically calculated based on cpu_port.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15749
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Drop config+patches for kernel 6.1.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15721
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Switch the apm821xx targets to kernel 6.6.
no complains received.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15721
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Set the appropriate cpu_port value based on the use of realtek,extif0 to extif2
instead of the additional cpu_port parameter.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15033
Signed-off-by: Robert Marko <robimarko@gmail.com>
refreshed kernel config + patches
otherwise same as 6.1/5.15.
Tested on: WNDAP620, WNDAP660, MyBook Live Single, MR24, MX60, WNDR4700
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
With the default BUILD_BOT configuration on a linux 6.6 kernel,
the WNDR4700's kernel no longer fits into the alloted ~3.5MiB,
even with LZMA compression.
Bigger kernels are possible, but there's a problem with Netgear's
"bootcmd":
> if loadn_dniimg 0 0x180000 0x4e0000 && chk_dniimg 0x4e0000; then nand read 0x800000 0x180000 0x20000;bootm 0x500000 - 0x800040;else fw_recovery; fi"
This loads the dni-image starting offset 0x180000 from the NAND
flash (which is the DTB partition) to 0x4e0000 in the RAM. It then
checks whenever the provided image is "valid". If it is then it
reads the DTB again to 0x800000 in the RAM and starts the extraction
and boot process. (If the image wasn't valid then it starts the
automated firmware recovery).
The issues here are that first: the kernel image gets "squeezed"
between 0x500040 and 0x7fffff... And second, the decompressor
only has area 0x0 - 0x500000 for decompression.
Hence the image now requires to update the bootcmd by providing
new values (which have been successfully tested with the original
Netgear WNDR4700 v1.0.0.56 firmware) for the RAM locations and
make full use of the fact that loadn_dniimg loads the DTB as well.
This needs to be done only once. Just connect a serial adapter to
interface with uboot and overwrite (and save) the new bootcmd.
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
Steps:
0. Power-off the WNDR4700
1. Connect the serial interface (you need to open the WNDR4700)
2. Power-up the WNDR4700
3. Monitor the boot-sequence and hit "Enter"-key when it says:
"Hit any key to stop autoboot" (Be quick, you have a ~2 second window)
4. in the Prompt enter the following commands (copy & paste)
setenv bootcmd "if loadn_dniimg 0 0x180000 0xce0000 && chk_dniimg 0xce0000; then bootm 0xd00000 - 0xce0040;else fw_recovery; fi"
saveenv
run bootcmd
Note: This new bootcmd will also unbrick devices that were bricked
by the bigger 4.19-6.1 kernels.
Note2: This method was tested with a WNDR4700. A big kernel with most
debug features enabled on v6.6.22 measured 4.30 MiB when compressed
with lzma. The uncompressed kernel is 12.34 MiB. This is over the 3 MiB,
the device reserves for the kernel... But it booted! For bigger kernels,
the device needs repartitioning of the the ubi partition due to the
kernel+dtb not fitting into the partition.
Note3: For initramfs development. I would advice to load the initramfs
images to 0x800000 (or higher). i.e.: tftp 800000 wndr4700.bin
Note4: the fw_recovery uboot command to transfer the factory image to
the flash still works.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This service was unfunctional due to not having its executable bit set.
Furthermore, sysupgrade complains about the file being present in images.
Also, the tc654 driver doesn't provide pwm1_enable sysfs file, instead its
now called pwm1_mode.
Please note that the fan was always spinning. It should now turn off, when
there's enough the thermal headroom.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
it is possible to boot and run OpenWrt from an image on an USB-Stick
on the MyBook Live DUO. (No, the MyBook Live Single does NOT have an
USB-Port and attempts at enabling it sadly all failed... so far).
To do that:
First, prepare a USB-Stick by writing the raw and uncompressed OpenWRT
factory image for the device onto the stick (i.e.
# gunzip -c openwrt-*wd_mybooklive*-factory.img.gz > /dev/sd$XX).
Then enter the u-boot via an attached TTL/CMOS 3.3V cable adapter and
give the following commands a try in the:
usb start; sata init
ext2load usb 0:1 ${fdt_addr_r} /boot/apollo3g.dtb
ext2load usb 0:1 ${kernel_addr_r} /boot/uImage
setenv bootargs 'root=/dev/sdc2 rw rootfstype=squashfs,ext4 rootdelay=5'
run addtty; bootm ${kernel_addr_r} - ${fdt_addr_r}
Notes:
- booting from USB-Sticks takes a long time! Be prepared to wait a few
minutes. (~3 minutes for 4 MiB /boot/uImage file on a USB 2.0 Stick)
- the bootargs part 'root=/dev/sdX2' depends on how many HDDs/SSDs are
slotted in. (if none: then use sda, if one: sdb. if two: sdc)
- rootdelay is important as the storage on the USB-Sticks do not show
up fast enough. 5 seconds might be excessive though.
- it's possible to concat these commands together in one line and
write it into u-boot's "bootcmd" environment variable and save the
environment to make the device to always boot from USB from then on.
if you have accidentally overridden the 'bootcmd' and want to return
to 'spec' enter the following commands :
setenv bootcmd 'run boot_sata_script_ap2nc'
saveenv
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Note about the MyBook Live.
The MyBook Live didn't have the encompassing fixed-partitions.
This is needed for the u-boot,env compatible to be read as otherwise
the kernel assumes this is a legacy NOR/NAND node and this binding
is unsupported.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
prepend-dtb got extended to handle the Meraki devices too,
the problem here was that the Netgear WNDR4700 expects an
u-boot header in front of the DTB, whereas Meraki devices
don't.
Since the header was dropped, the WNDR4700's uboot started
to complain:
Bad Magic Number,it is forbidden to be written to flash!!
when flashing the factory.img since it expects an u-boot
header there.
Fixes: 5dece2d9355a ("apm821xx: switch over from DTB_SIZE to DEVICE_DTC_FLAGS")
Reported-by: @kisgezenguz
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
though, ata-dwc is built-in on the target already.
Fixes: fd9dc10530 ("apm821xx: make ata-dwc as a standalone module")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
module is only useful for apm821xx targets, so
limit visability to just this target.
Fixes: 55fbcad20a ("apm821xx: make crypto4xx as a standalone module")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Make the crypto4xx crypto accelerator support as a standalone module.
This saves 90kb on a gzipped kernel.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
In order to cut down on the Netgear WNDR4700, the ata
driver can be outsourced. This helps other apm821xx
devices too to save up on kernel size (~200 kb).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
it was reported that this flag caused the mx60
not to boot anymore.
Fixes: f095822699 ("apm821xx: convert legacy nand partition layou")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
specify that this functions adds a Cisco Meraki
special-sauce header for their custom loader/uboot.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
All targets are bumped to 5.15. Remove the old 5.10 patches, configs
and files using:
find target/linux -iname '*-5.10' -exec rm -r {} \;
Further, remove the 5.10 include.
Signed-off-by: Nick Hainke <vincent@systemli.org>
libdeflate's gzip compressor provides a better
compression ratio and uboot's decompressor has
no problem with the data streams.
Tested on MX60, WNDR4700, WNDAP660
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Manually rebased:
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
[Move gro_skip in 680-NET-skip-GRO-for-foreign-MAC-addresses.patch to old position]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
use the toolchain's default CPU (464fp) as the CPU option.
This fixes a CPU selection prompt which shows up now.
CPU selection
> 1. Generic 32 bits powerpc (POWERPC_CPU) (NEW)
2. Rely on the toolchain's implicit default CPU (TOOLCHAIN_DEFAULT_CPU) (NEW)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
All targets expect the malta target already activate the CONFIG_GPIOLIB
option. Move it to generic kernel configuration and also activate it for
malta.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tim Small reported:
| Viewing the 'Network' -> 'Switch' config page in LuCI:
|
| The LuCI LAN 1 port corresponds to the port physically
| labelled 2 at the rear of the device.
| [...]
|
| When a patch cord is attached to the port labelled 1 [...],
| the LED labelled 2 illuminates. [...]
=> Ports, LuCI and LEDs are reversed/don't match.
Reported-by: Tim Small
Fixes: #10111
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This is now built-in, enable so it won't propagate on target configs.
Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca9367069 ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
As per the series:
<https://www.spinics.net/lists/devicetree/msg508906.html>
"Enforce specific naming pattern for children (keys) to narrow the
pattern thus do not match other properties. This will require all
children to be properly prefixed or suffixed (button, event, switch
or key)."
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The MBL has a 512KiB Microchip SST39VF040 chip for uboot and
not much else.
Thanks to Ewald who figured out that the "jedec-probe" vs.
"jedec-flash" was the wrong binding. With this information
and the jedec-probe support enabled => the chip works.
| physmap-flash 4fff80000.nor_flash: physmap platform flash device: [mem 0x4fff80000-0x4ffffffff]
| Found: SST 39LF040
| 4fff80000.nor_flash: Found 1 x8 devices at 0x0 in 8-bit bank
Suggested-by: Ewald Comhaire <e.comhaire@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
