This commit adds support for Xiaomi Mi WiFi Router 3G.
Short specification:
- MT7621AT + MT7603EN + 7612EN
- 256MB DDR3 RAM
- 128MB NAND flash
- 1+2 x 1000M Ethernet
- 1x USB 3.0 port
- reset button
- yellow, blue, red leds
Installation through telnet/ssh:
- copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and
lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it
from LEDE download site to /tmp
- switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if
wgetted from LEDE download site
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0
- run: mtd erase kernel0
- run: reboot
Originally stock firmware has following partitions:
- ...
- kernel0 (primary kernel image)
- kernel1 (secondary kernel image, used by u-boot in failsafe routine)
- rootfs0 (primary rootfs)
- rootfs1 (secondary rootfs in case primary fails)
- overlay (used as ubi overlay)
This commit squashes rootfs0, rootfs1 and overlay partitions into 1, so
it can be used by LEDE fully for package installation, resulting in 117,5MiB.
This device lacks hw watchdog, so adding softdog instead (stock does the same).
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The VoCore2 Lite uses the same PCB as the Vocore2.
This patch moves the common VoCore2 parts into dtsi.
Removed memory node in the device tree source file.
Memory is detected automatically.
http://vocore.io/http://vonger.net/http://vonger.cn/
Specifications:
- SoC: MediaTek MT7688AN
- RAM: 64MB DDR2 EtronTech EM68B16CWQH-25H
- Flash: 8MB NOR SPI Flash GigaDevice GD25Q64CWIG
- Wireless: Built into MT7688AN with onboard IPEX connector
Firmware installation:
- VoCore2-Lite ships with firmware forked from OpenWrt.
- Installation from the bootloader is recommended.
- If using luci/sysupgrade use the -n option (do not keep settings)
original firmware uses a modified proprietary MediaTek wireless driver.
- The wireless is disabled by default in LEDE.
- If reverting to factory firmware using the bootloader is recommended.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Tested by: Noble Pepper <noblepepper@gmail.com>
The Netgear EX3800 is essentially an EX3700 with a mains output socket.
Both devices use the exact same firmware image (original firmware is named
EX3700-EX3800-version.chk).
This patch adds suport by renaming the EX3700 device to EX3700/EX3800 and
updating the necessary glue.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Cleanup the dtsi files and remove one layer of dtsi. Set the size of
the firmware partition to a value matching the flash size from the
board (variant) name.
Remove the usb led trigger. There is neither a default config for the
usb led trigger nor a LED for usb activity indication.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Reference the Omnima MiniEMBWiFi device tree source file in the image
build code. Otherwise the dts of the image processed before is used.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With d2b6bf1416 ("ramips: fix image validation errors") the board
name was changed to fix an image validation error. But this change
wasn't applied to all other files using the board name, which broke
sysupgrade.
Revert this change and use the former board name in the metadata
instead.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The WMDR-143N is a small module originally used as a Wifi client
in some Loewe smart TV sets. It is sold cheaply at german surplus
shops. The module contains a RT3662 SOC.
Specifications:
- 500 MHz CPU Clock
- 1x 10/100Mbps Ethernet (pin header)
- 32 MB of RAM
- 8 MB of FLASH
- 2T3R 2.4/5 GHz (SOC internal)
- 3 Antennas on PCB
- UART pads on PCB (J3: 1 = +3.3V, 2 = RX, 3 = TX, 4 = GND), TX
and RX are 3,3V only! The square hole is pin 1
- Power supply pads on PCB (J6: 1 and 2 = +5V, 3 and 4 = GND)
The square hole is pin 1
The original firmware has two identical kernel/rootfs images and
two "Factory" calibration data blocks in flash. The LEDE image
leaves only the first "Factory" block in place and uses both
"Kernel" blocks and the redundant "Factory" block together to gain
enough space for the jffs2 partition.
Flash instructions:
You need UART and Ethernet connections to flash the board. Use
the LEDE "sysupgrade.bin" image with tftp.
Apply power to the board and in the first 5 seconds, hit 2 to
select TFTP upload. The bootloader asks for board- and server IP
addresses and filename.
Alternate method: With the vendor firmware running, assign an IP
address to the ethernet port, tftp the firmware image to
/tmp and write to mtd4 ("KernelA").
Signed-off-by: Oliver Fleischmann <ogf@bnv-bamberg.de>
[remove pinctrl node from dts, no pin is used as GPIO]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The GnuBee Personal Cloud One crowdfunded on https://www.crowdsupply.com
It is a low-cost, low-power, network-attached storage device.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: DDR3 512 MB
- Flash: 32 MB
- Six SATA ports for 2.5" Drives
- One micro SDcard
- One USB 3.0
- Two USB 2.0
- Gigabit Ethernet: 1 x WAN and 1 x LAN
- UART 3.5mm Audio Jack or 3 pin header - 57600 8N1
- Four GPIOs available on a pin header
Flash instructions:
The GnuBee Personal Cloud One ships with libreCMC installed.
libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt.
As such one can upgrade using the webinterface or sysupgrade.
Das U-Boot has multiple options for recovery or updates including :
- USB
- http
- tftp
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
[use switchdev led trigger, all interfaces are in vlan1; rename leds
according to board.d setting; remove ge2 group from the pinmux, this
group doesn't exist in the driver]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The TP-Link RE350 is a wall-wart AC1200 range extender/access point with
a single gigabit ethernet port and two non-detachable antennas, based on
the MT7621A SoC with MT7603E and MT7612E radios.
Firmware wise it is very similar to the QCA based RE450.
SoC: MediaTek MT7621A (880MHz)
Flash: 8MiB (Winbond W25Q64)
RAM: 64MiB (DDR2)
Ethernet: 1x 1Gbit
Wireless: 2T2R 2.4Ghz (MT7603E) and 5GHz (MT7612E)
LEDs: Power, 2.4G, 5G (blue), WPS (red and blue), ethernet link/act
(green)
Buttons: On/off, LED, reset, WPS
Serial header at J1, 57600 8n1:
Pin 1 TX
Pin 2 RX
Pin 3 GND
Pin 4 3.3V
Factory image can be uploaded directly through the stock UI.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
It uses one MT7615D radio chip with DBDC mode enabled. This mode allows
this single chip act as an 2x2 11n radio and an 2x2 11ac radio at the
same time. However mt76 doesn't support it currently so there is no
wireless available.
Specification:
- SoC: MediaTek MT7621AT
- Flash: 16 MB
- RAM: 128 MB
- Ethernet: 1 x WAN (10/100/1000Mbps) and 4 x LAN (10/100/1000 Mbps)
- Wireless radio: MT7615D on PCIE0
- UART: 1 x UART on PCB - 57600 8N1
Issue:
- Wireless radio doesn't work due to the lack of driver.
Flash instruction:
Using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press 2,then follow the instruction to
set device and tftp server IP address and input the firmware
file name.U-boot will then load the firmware and write it into
the flash.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Most of the ubnt-erx definition can be reused; the package removals in
DEVICE_PACKAGES have become redundant after d17cb4a68a "ramips: purge
default packages on MT7621".
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with
5-port FE switch and non-detachable antennas. Both are very similar
and are based on MediaTek MT7628NN (aka MT7628N) WiSoC.
The difference between these two models is in number of available
LEDs, buttons and power input switch.
This work is partially based on GitHub PR#974.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- TL-WR840N v4: 5x LED (GPIO-controlled), 1x button
- TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input
switch
* WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Factory image notes:
These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device ("0x4"/"0x13" for these devices) but it seems
that anything other than "0" is correct.
We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash.
Tests showed that the GUI upgrade routine copies value of "Additional
Hardware Version" from existing firmware into offset "0x2023c" in
provided file, _before_ storing it in flash. In case of vendor firmware
upgrade files (which all include U-Boot image and two headers), this
offset points to the matching field in kernel+rootfs firmware part
header. Unfortunately, in case of LEDE factory image file which contains
only one header, it points to the offset "0x2023c" in kernel image. This
leads to a corrupted kernel and ends up with a "soft-bricked" device.
The good news is that U-Boot in these devices contains well known tftp
recovery mode, which can be triggered with "reset" button. What's more,
in comparison to some of older MediaTek based TP-Link devices, this
recovery mode doesn't write whole file at offset "0x0" in flash, without
verifying provided file in advance. In case of recovery mode in these
devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes
from rest of the file are stored in flash at offset "0x20000".
Flash instruction:
Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
To access U-Boot CLI, keep pressed "4" key during boot.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
There are already two targets (lantiq, ramips) which use mktplinkfw2
tool for creating images. This de-duplicates code, introduces two new
build commands: tplink-v2-header, tplink-v2-image and makes use of
them in place of old, (sub)target specific ones.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This patch adds support for the Ubiquiti EdgeRouter X-SFP and
improves support for the EdgeRouter X (PoE-passthrough).
Specification:
- SoC: MediaTek MT7621AT
- Flash: 256 MiB
- RAM: 265 MiB
- Ethernet: 5 x LAN (1000 Mbps)
- UART: 1 x UART on PCB (3.3V, RX, TX, GND) - 57600 8N1
- EdgeRouter X:
- 1 x PoE-Passtrough (Eth4)
- powered by Wallwart or passive PoE
- EdgeRouter X-SFP:
- 5 x PoE-Out (24V, passive)
- 1 x SFP (unknown status)
- powered by Wallwart (24V)
Doesn't work:
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
nand/spi drivers do not support pin sharing,
so it is not accessable and disabled. Stock
firmware could read it and it was empty.
Installation
via vendor firmware:
- build an Initrd-image (> 3MiB) and upload the factory-image
- initrd can have luci-mod-failsafe
- flash final firmware via LuCI / sysupgrade on rebooted system
via TFTP:
- stop uboot into tftp-load into option "1"
- upload factory.bin image
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
This patch adds supports for the GL-inet GL-MT300N-V2.
Specification:
- SoC: MediaTek MT7628AN
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR
- Ethernet: 1 x WAN (100 Mbps) and 1 x LAN (100 Mbps)
- USB: 1 x USB 2.0 port
- Button: 1 x switch button, 1 x reset button
- LED: 3 x LEDS (system power led is not GPIO controller)
- UART: 1 x UART on PCB (JP1: 3.3V, RX, TX, GND)
Installation through Luci:
- The original firmware is LEDE, so both LuCI or sysupgrade can be used.
- Do not keep settings, for sysupgrade please use the -n option.
Installation through bootloader webserver:
- Plug power and hold reset button until red LED blink to bright.
- Install sysupgrade image using web interface on 192.168.1.1.
Signed-off-by: Kyson Lok <kysonlok@gmail.com>
[match maximum image size with firmware partition]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This PR allow the 3G modem embedded in the DWR-512 to be managed
by the wwan-ncm scripts. The modem will use the usb-option and
usb-cdc-ether drivers.
The DWR-512 DT is updated accordingly.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
Specification:
- SoC: MediaTek MT7620A (580 MHz)
- RAM: 64 MiB (Winbond W9751G6JB-25)
- Flash: 16 MiB (Spansion S25FL128SAIF00)
- LAN: x4 100M
- WAN: x1 100M
- Others: USB 2.0, reset button, wps button and 9 LEDs
Issues:
- 5 GHz band is not functional (missing driver support)
Installation:
Asus windows recovery tool:
- install the Asus firmware restoration utility
- unplug the router, hold the reset button while powering it on
- release when the power LED flashes slowly
- specify a static IP on your computer:
IP address: 192.168.1.75;
Subnet mask 255.255.255.0
- Start the Asus firmware restoration utility, specify the sysupgrade
image, and press upload
TFTP Recovery method:
- set computer to a static ip, 192.168.1.75
- connect computer to the LAN 1 port of the router
- hold the reset button while powering on the router for a few seconds
- send firmware image using a tftp client; i.e from linux:
$ tftp
tftp> binary
tftp> connect 192.168.1.1
tftp> put lede-ramips-mt7620-rt-ac51u-squashfs-sysupgrade.bin
tftp> quit
Signed-off-by: Ørjan Malde <foxyred333@gmail.com>
This device exactly same as NBG-419N but with USB port and USB Led.
Specification:
- SoC: Ralink RT3052 (MIPS24Kc) @384MHz
- RAM: 32 MiB
- Flash: 8 MiB
- WLAN: WiSoC 2T2R/300Mbps (2.4GHz)
- LAN: 4x100M
- WAN: 1x100M
- USB: 1x2.0
Installation via serial console (57600 8N1) from TFTP server
- rename the firmware to something shorter, for example
"sysupgrade.bin" (max. 32 chars)
- copy firmware TFTP server's directory
- when you power on device, and see U-Boot log, immediatly push "2"
once.
- You will see this message:
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?
- Push "y", and enter: device IP, then TFTP server's IP, and then
image firmware file name.
The firmware will be downloaded within ~30 seconds and flashed to the
device (It will take about 2 minutes).
Signed-off-by: Alexey Belyaev <spider@spider.vc>
[squash commits, compact commit message, fix compatible string, remove
superfluous pinmuxes]
Signed-off-by: Mathias Kresin <dev@kresin.me>
In order to have a smaller initramfs image remove all packages not
needed on all devices and add them explicitely for those actually
needing them. Also remove wpad-mini from ramips default package set
and add it to all sub-targets except for MT7621.
While at it reorder packages alphabetically and replace kmod-mt76 with
kmod-mt7603 and/or kmod-mt76x2 depending on the chip actually used on
a specific board.
Hopefully fixes FS#758
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The ZBT-WG826 is available with 16 or 32 MByte of flash. Split the
device tree source file, rename the currently supported 16 MByte
version and add the 32 MByte variant.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Digineo AC1200 Pro is the 32MB flash variant of the ZBT-WG3526 with
unpopulated/exposed sdhci slot. Rename to board to the OEM/ODM name and
add the sdhci kernel module to use it for multiple clones.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The ZBT-WG3526 is available with 16 or 32 MByte of flash. Rename the
current supported 16MByte version to indicate which flash size variant
is supported.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Specification:
- SoC: MT7621AT, MT7603EN and MT7612EN
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 512 MiB (EM6GE16EWXD-12H)
- Ethernet: 1 x WAN (10/100/1000Mbps) and 4 x LAN (10/100/1000 Mbps)
- Others: USB 2.0, micro SD slot, reset button and 8 x LEDs
Issues:
- Two LEDs for 2.4 GHz and 5 GHz Wi-Fi do not work, can't find GPIOs.
- The pwr LED is not GPIO controllable
How to install:
- The original firmware is OpenWrt, so both LuCI or sysupgrade can be used.
- Do not keep settings, for sysupgrade please use the -n option.
Signed-off-by: Jiawei Wang <buaawjw@gmail.com>
We need to keep the former used (unmodified) boardname in the metadata.
Otherwise an upgrade from an board using the old boardname will be
refused.
Fixes: a75ce960ac ("ramips: use different board names for variants")
Signed-off-by: Mathias Kresin <dev@kresin.me>
PSG1218 got only 4 Ethernet ports and WAN on port 3 while
PSG1218K2C got 5 Ethernet ports and WAN on port 4
Switch to use kmod-kt76x2 instead of kmod-mt76 for both devices while
at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Netgear R6220 requires the kmod-usb3 package and misses
kmod-usb-ledtrig-usbport package to setup the configured usb led
trigger.
Drop the already target selected kmod-mt76.
Fixes: FS#686
Fixes: 38bee61dab ("ramips: add support for Netgear R6220")
Signed-off-by: Mathias Kresin <dev@kresin.me>
The factory image has an uImage header covering the entire image and
not only the kernel. The original uImage header which covers only the
kernel is appended to the end of the image.
During LEDE boot the uImage rootfs splitter skips the whole filesystem,
can't find a valid filesystem magic and panics.
The last known working version was OpenWrt 14.07, which simply kept on
searching for an uImage header if the first found didn't resulted into
a working rootfs. This behaviour is kind of error prone since it could
produce false positives.
Since the sysupgrade image works fine in combination with the tftp
recovery for doing the initial installation of LEDE, simply drop the
factory image.
Related: FS#462
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for the Zbtlink ZBT-WE2026.
Specification:
- SoC: MediaTek MT7620N (580MHz)
- RAM: 64 MiB
- Flash: 8 MiB SPI
- LAN: 4x100M
- WAN: 1x100M
Installation through bootloader webserver:
- With the power unplugged press and hold reset button.
- Plug power and hold reset button until LED starts to blink.
- Install sysupgrade image using web interface on 192.168.1.1.
Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M
The -factory images can be flashed from the device's web
interface or via nmrpflash.
Co-authored-by: Paul Oranje <por@xs4all.nl>
Signed-off-by: Paul Oranje <por@xs4all.nl>
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
This patch adds support for the Netgear R6220, aka Netgear AC1200 and
R6220-100NAS.
Specification:
- SoC: MediaTek MT7621ST (880 MHz)
- Falsh: 128 MiB (Macronix MX30LF1G08AA-TI)
- RAM: 128 MiB (Nanya NT5CB64M16FP-DH)
- Wireless: MediaTek MT7603EN b/g/n , MediaTek MT7612EN an+ac
- LAN speed: 10/100/1000
- LAN ports: 4
- WAN speed: 10/100/1000
- WAN ports: 1
- Serial baud rate of Bootloader and factory firmware: 57600
Installation through telnet:
- Copy kernel.bin and rootfs.bin to a USB flash disk, plug to usb port
on the router.
- Enable telnet with link: http://192.168.1.1/setup.cgi?todo=debug
(login if required, default: admin password)
- You will see "Debug Enabled!"
- Telnet 192.168.1.1 and login with "root"
- ls /mnt/shares/ to find out path of your USB disk. 'myUdisk' for
example.
- cd /mnt/shares/myUdisk
- mtd_write write rootfs.bin Rootfs
- mtd_write write kernel.bin Kernel
- reboot
nmrpflash can be used to recover to the netgear firmware if a broken
image was flashed.
Signed-off-by: Hanqing Wong <hquu@outlook.com>
* The left most mini-PCIe slot (the one attached to SIM2) can be
power-cycled by setting GPIO 0 to high/low.
* The D240 only needs the MT76x2 module, so update makefile to reflect this.
Note that until the default mt7620 target is updated, then kmod-mt76 (and thus
kmod-mt7603) will be selected by default.
v2->v3:
* Indentation error.
v1->v2:
* Rename gpio and remove redundant comment (thanks Piotr Dymacz)
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
mtk-mmc/mtk_sd.ko only depends on mmc_core and mmc_block.
And, we remove kmod-sdhci dependence assignment from all related target devices.
Signed-off-by: Furong Xu <xfr@outlook.com>
These modules are not needed by the EX2700, since it does not
have an external wifi chip (MT7620A is covered by rt2x00).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
This device features both a 2.4 and 5Ghz radio, and supports
802.11a/b/g/n/ac modes.
It has 5 Gb-Ethernet ports and a USB 3.0 host port.
It is powered by the Mediatek MT7621 SoC, and the MT7602E and MT7612E wifi
chipsets, together with 128MB of RAM and 16 MB of SPI Flash.
The stock firmware is in fact based on some openwrt barrier breaker, with a
mediatek SDK kernel, and an afoundry custom made web interface (not LuCI
based).
Firmware update page on the stock web interface can not accept sysupgrade
images, it bricks the device.
At this point, the only working solution I found was to connect to the
serial console port (available on J4 header) and to use opkg to install
dropbear.
Then scp the sysupgrade file in the device's /tmp and run sysupgrade from
console without preserving configuration files.
Signed-off-by: Francois Goudal <francois@goudal.net>
This patch adds supports for the HiWiFi HC5962(gee4) http://www.hiwifi.com
Short specification:
- MT7621AT + MT7612EN + 7603EN
- 256MB DDR3 RAM
- 128MB NAND flash
- 1+3 x 1000M Ethernet
- 1x USB 2.0 port. 1x USB 3.0 port.
- reset button
- UART pad on PCB (JP3: TX, RX, GND, 3.3V)
Flash instruction:
1, Download lede-ramips-mt7621-hc5962-squashfs-factory.bin
2, Login as root via SSH on 192.168.199.1 and then copy factory.bin(using wget or nc or...) to /tmp/
3, use the following commands:
$ mtd write /tmp/lede-ramips-mt7621-hc5962-squashfs-factory.bin firmware
$ mtd erase firmware_backup && reboot
After reboot you should be able to login as root via SSH on 192.168.1.1
Signed-off-by: ZengFei Zhang <zhangzengfei@kunteng.org>
HC5661A is almost the same as HC5661 but MT7628AN is used instead of MT7620A.
- MT7628AN
- 128 MiB DDR2 RAM (W971GG6KB-25)
- 16 MiB SPI NOR flash (W25Q128)
- SD slot (not work yet)
- 1+4 x 100M Ethernet
- 802.11 b/g/n Wi-Fi
- 3 x LED
- 1 x button
- UART pad on PCB (JP1: TX, RX, GND, 3.3V)
The factory flash layout seems different from HC5661.
"hwf_config" is renamed to "oem" and its size changes to 0x20000.
It is modified accordingly in the dts file.
0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "hw_panic"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000160000 : "kernel"
0x000000160000-0x000000fc0000 : "rootfs"
0x000000bb0000-0x000000fc0000 : "rootfs_data"
0x000000fc0000-0x000000fe0000 : "oem"
0x000000fe0000-0x000000ff0000 : "bdinfo"
0x000000ff0000-0x000001000000 : "backup"
0x000000050000-0x000000fc0000 : "firmware"
To install LEDE, enabled the "developer mode",
which will *void your warranty* and open the SSH server at port 1022.
sysupgrade -n -F lede-ramips-mt7628-hc5661a-squashfs-sysupgrade.bin
SD slot:
- Tried to add modules kmod-sdhci kmod-sdhci-mt7620, and corresponding dts block.
- It will block WAN + 3xLAN ports, only one LAN works.
- I'm not sure why, everything else works fine.
Signed-off-by: Wang JiaWei <buaawjw@gmail.com>
This patch frees up flash space on the EX2700, by
removing unused mt76 drivers and firmware.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
mtdsplit_lzma requires that the rootfs be aligned to a block boundary.
Pad the kernel partition to make this so.
Signed-off-by: Claudio Leite <leitec@gmail.com>
The Sanlinking Technologies D240
(http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same
device as the ZBT WE826, so adding support for it in LEDE is straight forward.
The differences is that the D240 has two mini-PCIe slots (instead of one), blue
LEDs and supports PoE.
Specification:
* CPU: MT7620A
* 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps.
* 16 MB Flash.
* 128 MB RAM.
* 1x USB 2.0 port.
* 2x mini-PCIe slots.
* 2x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.
Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to
test the SD card reader.
The device comes pre-installed with an older version of OpenWRT, including Luci.
In order to install LEDE, you need to follow the existing procedure for updating
OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to keep
existing settings. The default router address is 192.168.10.1 and
username/password admin/root (at least on my devices).
If you brick the device, the procedure for recovery is the same as for the
WE826. Please see the wiki page for that device for instructions.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
This patch moves the fakeroot code required by some devices to
`image-commands.mk`.
Create the fakeroot on the fly by using the undocumented -s (skip copy)
parameter of mkimage.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
[remove unused NETGEAR_KERNEL_MAGIC, remove workarounds to have a dummy
rootfs for mkimage]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The factory image can't be bigger than 3328 KByte. If the image is
bigger than that, the gemtek-header tool throws an error and breaks
the build.
Make sure the output file to which the gemtek header should be added
exists and wasn't removed during the check-size step because of it
size. This will prevent hard errors in case the factory image is to big
similar to what is done for sysupgrade images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This activates the CONFIG_MIPS_APPENDED_RAW_DTB kernel configuration and
configures the F5D8235 V1 target to use append-dtb for kernel creation
instead of OWRTDTB.
Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
[Jo-Philipp Wich: rewrap commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Buffalo WCR-1166DS is a small wireless router with
- MT7628AN + MT7612E
- 64MiB DDR2 SDRAM
- 16MiB SPI flash
- 2T2R 11ac/a/b/g/n Wi-Fi
- 2x 10/100M ethernet switch
- 8x programmable LED
- 3x button
- UART pad on PCB (J2: 3.3V, GND, TX, RX)
factory image can be installed via stock web UI.
due to the "dual image" function in the bootloader, the second half of
the SPI flash ("firmware2" partition) cannot be used as a part of the
file system.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
ramips/rt288x WLI-TX4-AG300N was missing support for its 100Mbit switch which
should be included by default.
Signed-off-by: Yo Abe <abe.geel@gmail.com>
[Jo-Philipp Wich: picked from OpenWrt PR#359, rewrap commit msg, fix Sob]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This patch adds support for the Netgear WN3000RPv3
http://www.netgear.com/support/product/wn3000rpv3.aspx
Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Serial: JP1 header, 57600-8N1
- Stock firmware based on OpenWRT Kamikaze
Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This is why the same fakeroot image is used for the WN3000
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io)
Specifications:
- SoC: MediaTek MT7688AN (580MHz, ramips)
- Omega2
- RAM: 64MB DDR
- Storage: 16MB NOR SPI flash onboard
- Omega2+
- RAM: 128MB DDR
- Storage: 32MB NOR SPI flash onboard + microSD slot
- Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter
- Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port
- Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock)
- All Docks Provide:
- Micro-USB port to provide power to the Omega
- On the Expansion and Mini Docks, can also access the terminal (UART0) via serial
- USB 2.0 socket connected to Omega
- Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide:
- Omega GPIO breakout
- Allows for connection of Omega Expansions:
- Ethernet Expansion
- Relay Expansion
- PWM Expansion
- OLED Expansion
- Ethernet Expansion
- Proto Expansion
- Cellular Expansion
Signed-off-by: Lazar Demin <lazar@onion.io>
I made a commit that added the RTC driver to the kernel config with
the intent that it would fix hctosys. Unfortunately while the RTC
driver is in there, it's connected through I2C, the driver for which
comes in module form and is thus loaded late. After this commit, it
works fine.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This patch adds support for the VoCore VoCore2 and its complementary
"ultimate" dock.
Specifications:
- SoC: MediaTek MT7628AN (580MHz, ramips)
- RAM: 128MB DDR2 166MHz
- Storage: 16MB NOR SPI flash onboard + microSD slot on dock
- Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2
boards with onboard 1x chip antenna
- Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header
- Dock hardware:
- USB 2.0 socket
- MicroSD socket
- 100Mbps Ethernet x1
- 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S
DAC/ADC (support WIP)
- Micro USB for power and console (UART2)
Initial installation:
- VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on
SSID "VoCore2"
- Connect to VoCore2 by Ethernet or Wi-Fi
- `ssh root@192.168.1.1` (password is "vocore")
- scp/wget/etc. LEDE sysupgrade.bin to VoCore2
- `sysupgrade -n <your image>.bin` (don't keep old config, as the
original firmware uses Ralink SDK Wi-Fi drivers and not
mt76+mac80211)
- after sysupgrade completes, Wi-Fi will be disabled by default so use
Ethernet or the micro USB console to configure Wi-Fi again
Signed-off-by: Andrew Yong <me@ndoo.sg>
There was a typo in Makefile that prevented using these profiles.
Fixes: a75ce960ac ("ramips: use different board names for variants")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Use different names for flash size related board variants, to make sure
that only images for the actual flash size are considered as valid by
the image validation code.
Remove the flash size suffix from the string returned by
ramips_board_detect() to ensure that existing scripts relying on the
former used boardname are still working.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The name from the Device define will be used in the metadata. Due to
typos/different spelling, this name might not match the one exported in
/lib/ramips.sh.
Fix all name mismatches which were found by checking if the name used
in the metadata exists in /lib/ramips.sh.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Dlink DWR-512-B modem is a ralink 5350 processor based embedding
a 3G mini-pcie router.
The oem JBOOT bootloader has to be replaced by a RT5350 SDK
U-Boot such as https://github.com/stevenylai/ralink_sdk - U-Boot
configured for the RT5350 256MiB SDR.
Main reason to change the bootloader is the encrypted header used to
store the kernel image. In this way an image can only be generated
using the propietary binboy tool (included in the GPL distribution
from Dlink). The binboy tool doesn't allow to modify the kernel/rootfs
partition scheme. This is considered a big constraint (limited kernel
size and inefficient usage of flash space).
For interested people I pubblished the details of my investigation
about the encrypted firmware header here:
http://lists.infradead.org/pipermail/lede-dev/2016-October/003435.html
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
Factory image can be installed via Zyxel WebUI.
Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
[removed linux,modalias parameter from flash node in dts]
[removed sdhci node from dts; no sd card slot here]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Sitecom firmware upgrade file has SENAO_FIRMWARE_TYPE 2 set. This
looks rather wrong since SENAO_FIRMWARE_TYPE 2 is kernel only but the
file is way to big for only including a kernel.
The factory image need to have the dlf file extension. Otherwise the
Sitecom firmware rejects the file.
The stock firmware uses the following mac addresses:
LAN: 00:0C:F6:AA:BB:D8 (u-boot env: ethaddr)
2,4: 00:0C:F6:AA:BB:D8 (EEPROM)
5: 00:0C:F6:AA:BB:DC (EEPROM)
WAN: 00:0C:F6:AA:C8:43 (u-boot env: wanaddr)
Assuming the mac address range :D8 to :DC is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:
2.4GHz: 00:0C:F6:AA:BB:D8
LAN: 00:0C:F6:AA:BB:D9
WAN: 00:0C:F6:AA:BB:DA
5 GHz: 00:0C:F6:AA:BB:DC
The first MAC is assigned to the 2.4GHz WiFi interface
to keep compatibility with the SSIDs printed on the case, which have
the last three sextets of the MAC address appended.
There are still issues with the rt2x00 driver. It is not possible to
use both wireless interfaces at the same time. The 2.4 GHz
wireless (PCIe) only works if the internal 5GHz wireless is/has been
enabled or used for scanning. The internal 5GHz wireless only works if
the 2.4GHz wireless (PCIe) was never enabled. Disabling the 2.4Ghz
after it was enabled will result in stations seeing the 5Ghz AP but are
unable to connect.
Due to the not optimal working wifi the manufacture, backup and storage
partitions of the OEM firmware are kept for now to allow an easy switch
back to the Sitecom firmware.
Signed-off-by: Jasper Scholte <NightNL@outlook.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz).
RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot.
Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware.
The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices.
A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware.
Signed-off-by: Andrew Yong <me@ndoo.sg>
This patch adds the kmod-usb3 and kmod-usb-ledtrig-usbport packages to the
DIR-860L B1 profile. The DIR-860L B1 has a USB 3 port.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Images installed via TFTP recovery or the Edimax webinterface of the
3g-6200n(l) are writting with the edimax header to flash.
Use only one image type for these boards. The migration to the
factory only images need to be done via TFTP recovery.
Use the same start address for the 3g-6200n(l) factory images as the
stock firmware images.
Thanks to Jan Dostrasil for reporting all the issues of the 3g-6200nl
and the patient testing of all changes.
Signed-off-by: Mathias Kresin <dev@kresin.me>
applied bb-final-ramips-add-zyxel-nbg-419n2.patch from
123serge123, found at https://yadi.sk/d/1ZV0lKJwbTE65;
see https://forum.openwrt.org/viewtopic.php?pid=246905#p246905,
modified slightly to fit to CC release and to new lede build
system: image/rt305x.mk include file is used now
changed NBG-419N2.dts format to fit style of other dts files
Signed-off-by: Klaus <k-laus@quantentunnel.de>
- CPU: MT7620A 580MHz
- Flash: 8MB - RAM: 64MB
- External PA+LNA on both WLAN2.4 and WLAN5
- 4x LAN ethernet and 1x WAN ethernet
Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
kmod-rt2x00-lib and kmod-mac80211 need to be removed, as they depend on
kmod-cfg80211. kmod-rt2800-pci should not be installed anyways.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The D-Link DIR-860L B1 has a flash chip which doesn't support
4K sectors. Since the DIR-860L B1 was the only mt7621 board which had
the 4k blocksize set, the 4K sector support is removed from the kernel
config.
I've checked the flash chips of all boards having set a 4K blocksize
again. This time I searched harder to finding bootlogs instead of
relying on wikis articles and/or the device tree source file.
The Planex MZK-DP150N has an en25q32b instead of the mentioned one in
the dts. Albeit the en25q32b supports 4K sectors, 4K support is not
enabled in the driver. Change the blocksize for this board back to 64K.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Only add them where they are actually required.
Should help with compatibility issues with stock U-Boot images that
access UBI
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Now that all seama images are using the new build code this seama recipe
used with the old build code can be dropped.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set the blocksize for devices having only 4MB of flash for ramips
devices already using the new image build code.
Informations about the used flash chip are gathered from the OpenWrt
wiki, wikidevi, forums, OEM bootlogs or the compatible property in the
device tree source file.
The en25q32b from the AirLive Air3GII does not have 4k support in the
kernel.
For the following boards no information about the used flash chip could
be found and a 64k blocksize is assumed:
- Ralink V11ST-FE
- Ralink AP-RT3052-V22RW-2X2
- MediaTek MT7628 EVB
- MediaTek MT7621 EVB
- UPVEL UR-326N4G
- Buffalo WZR-AGL300NH
Signed-off-by: Mathias Kresin <dev@kresin.me>
The image generation for TEW-691GR and TEW-692GR was broken since
79d02229 due to the move of the UMedia recipe to another Makefile.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Thunder Timecloud is a small NAS with MT7621A. It has 1 USB port and an
SD Card slot. There is no wireless cards.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Now that the "sysupgrade-nand" step is used by non-NAND targets as well,
rename it to "sysupgrade-tar" to make it more generic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
D-Link DCH-M225 is based on Mediatek MT7620 with 64MB ram, 8MB flash,
3.5mm audio out support. but no ethernet and usb ports.
so you must default enable wifi.
Signed-off-by: Michael Lee <igvtee@gmail.com>
The NixCore X1 is a Ralink/MediaTek rt5350 WiFi Module.
http://nixcores.com/
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Drew Gaylo <drew@nixcores.com>
Pinmux for rgmii needs to be set to rgmii, not gpio.
Hide the ESW switch on boot (using new rgmii esw devicetree attribute).
Also add a Sitecom-specific profile, since the image needs to include
the rtl8366 kernel driver.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
The ZBT APE522II is a dual-radio outdoor CPE based on the MT7620a SoC. It has
64 MB RAM, 8 MB flash, 2 Fast Ethernet ports via internal switch (one with
802.3af 48V PoE support), a 802.11b/g/n SoC 2.4 GHz radio and an 802.11a/n/ac
MT7612E-based 5 GHz radio.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
DuZun DM06 is a develop board based on mt7628
64M RAM, 8M SPI Flash, 1 WAN, 1 LAN.
wm8960 codec with line out, line in and speaker output.
Signed-off-by: Michael Lee <igvtee@gmail.com>
The Widora board is similar to the Linkit 7688 but features a larger flash
capacity.
Signed-off-by: Yuan Chenmang <771992497@qq.com>
[Jo-Philipp Wich: Reword commit message, cleanup initial PR]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The previous image creation code would have failed if the
unpadded kernel uImage size was less than 64 bytes from the
next erase block boundary. Fix that.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
The bootloader on this device expects the kernel partition to end
on a 64k boundary. The last 64 byte of the kernel partition must
contain a valid uImage header (the fakeroot partition).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
add support for Planex MZK-EX750NP.
MZK-EX750NP is MT7620A and MT7610E based 11ac wifi repeater.
Built-in power supply.
64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49268
CS-QR10 is MT7620A based IP Camera.
the camera and sound does not work with kernel 4.4.
- camera chip is sn9c291.
- sound chip is wm8960.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49234
The WG3526 is the follow-up to the 2626 and is mostly the same, with the
excaption that the mt7602 has been replaced with the mt7603. The internal wifi
setup has also changed slightly. Based on my tests, everything that worked on
the 2626 works on the 3526 and with roughly the same performance.
v1->v2:
* Remove some references to 2626 that I had missed in the dts.
v2->v3:
* Update patch to match new file structure.
* Removed SD driver to be consistent with other MT7621 targets.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
SVN-Revision: 49213
ELECOM WRH-300CR is MT7620N based very small Wi-Fi router with 64MiB
DDR2 SDRAM, 16MiB SPI Flash, one fast ethernet port, and (internal but
easy-to-access) UART.
it also has internal USB hub and USB card reader which provide one USB
port, one SD card slot, and one microSD card slot.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
SVN-Revision: 49211
Currently the maximum image size defaults to 8Mbyte even though this model has 16Mbyte of flash memory.
Tested and works on my device.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
SVN-Revision: 49129
- all subtarget specific defines are in their own files
- common defines left in main Makefile
- each subtarget makefile idefed with SUBTARGET
- all subtargets compile tested
- few seems to be broken/unneeded things marked with FIXME
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 49104
According to the calling convention of the o32 ABI the
caller function must reserve stack space for $a0-$a3
registers in case the callee needs to save its arguments.
The assembly startup code does not reserve stack space
for these registers thus when the main C function needs
to save its arguments, that will cause a stack overflow.
Fix the assembly code to reserve stack space for the
registers to avoid that.
Untested. It seems that the lzma-loader is not used at all?
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 49062
1) Use leds to indicate:
Red - Power
Amber - Radio On
Blue - Wifi associated
2) Add profile to default build group for MT7628 subtarget
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>
SVN-Revision: 49045
Xiaomi MiWiFi Nano is based on Mediatek MT7628 with 64MB ram 16MB flash
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>
v3 includes changes suggested by L. D. Pinney & Karl Palsson-
Eliminate en25q64 (4MB) flash chip
Alphabetization
Remove hyphen in model
Rename profile from miwifinano.mk to xiaomi.mk
Add gpios that are attached to leds
SVN-Revision: 49024
This patch adds support for GL-MT750.
GL-MT750 is powered by MT7620A and MT7610e, dual band 802.11ac, 2.4G 300Mbps and 5G 450Mbps.
It has 5 LANs, MMC interface, USB, a lot of IOs and PoE support.
SVN-Revision: 48994
This patch adds support for GL-MT300N.
GL-MT300N is powered by MT7620N with 16MB flash, 64MB RAM,
2 LANs, USB, UART, GPIO and PoE support.
SVN-Revision: 48993
This patches adds support for GL-MT300A.
GL-MT300A is powered by MT7620A. It has 16MB flash, 128MB RAM,
Two LANs, USB, UART and MMC daughter board.
SVN-Revision: 48992
add support for Planex MZK-WDPR.
MZK-WDPR(MZK-WDPR-R01) is internet radio tuner.
This patch is "network board" in MZK-WDPR.
LCD board is non OpenWrt Platform.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 48968
This patch adds profiles and support for building factory and
sysupgrade images for JHR-N805R, JHR-N825R and JHR-N926R.
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48906
This patch adds support for building factory and sysupgrade images
for the Netgear EX2700 that don't require modification of u-boot
environment variables.
The bootloader on this device expects the kernel partition to end
on a 64k block boundary. The last 64 byte of the kernel partition
must contain a valid uImage header - in the stock firmware, this is
the uImage header of the root filesystem. For this patch, we're using
the uImage header of a 0 byte partition (ex2700-fakeroot.uImage).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
SVN-Revision: 48771
This patch adds support for Phicomm PSG1208.This is a router with MT7620A SoC with 8M flash and 64M ram.
The WPS led is uesd as status_led because the power light can't be controlled with GPIO.
It seems that the 5g wifi led is connected to MT7612E and it can't be controlled with GPIO too.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
SVN-Revision: 48721
This patch adds support for the Netgear EX2700 and builds an approriate
sysupgrade image.
What's missing is the option to build a factory image flashable via the
router's stock web interface, but this approach is hindered by the fact
that u-boot operforms an additional integrity check, which expects a
uImage header in the last 64 bytes of the "kernel" partition, which
the bootloader expects to be 960k, a size exceeded by the standard
OpenWrt kernel.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
SVN-Revision: 48698
The image name for the HiLink HLK-RM04 module has a typo and should read "RM04" rather than "RM02"
Signed-off-by: John Clark <inindev@gmail.com>
SVN-Revision: 48355
This router is based on MT7621 SoC, no wifi, no usb, nand.
Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.
Doesn't work:
* No GPIO leds. All leds are controlled by switch,
but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
nand/spi drivers do not support pin sharing,
so it is not accessable and disabled. Stock
firmware could read it and it was empty.
* PoE out.
Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.
U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.
Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47881
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.
This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.
Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>
SVN-Revision: 47845
Use kernel arch for dts compilation.
Also use Image/BuildDTB to build dts for ramips.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47823
netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.
this device only works on top of UBI.
Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons (reset button)
* ethernet switch and USB diag LEDs
* UART
* GPIOs
* sysupgrade
Tested and not working
* failsafe
Signed-off-by: YounJae Rho <luxflow@live.com>
SVN-Revision: 47619
Changes since V1:
I resend this patch for current trunk.The former V1 patch is for CC branch.
Signed-off-by: Shonn Lu <countrysideboy@qq.com>
SVN-Revision: 47617
Add support for Dovado tiny AC wifi router.
Soc: mt7620a
ram: 64MB
flash: 8MB
1x usb 2.0
two gigabit lan ports
5ghz wlan is not supported on this board since there is no gpl driverfor mt7610e wifi chip.
Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>
SVN-Revision: 47348
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com <http://www.hiwifi.com/>. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.
The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.
v3 fix
1: Spaces -> Tabs
2: Removed some packages
Signed-off-by: Xiaoning Kang <kangxn@163.com>
SVN-Revision: 47113
This patch is to add the WIZnet WizFi630A board as a new platform. The board is in mini pci express form factor.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
SVN-Revision: 46921
This patch add support for Planex DB-WRT01. DANBOARD route on
the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio.
DANBOARD is Cartoon character.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 46918
The following patch changes 7Links PX-4885 dts{,i} filenames, board, image and profile names from "PX4885" to "PX-4885" (for consistency).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46629
The following patch changes Buffalo WMR-300 dts filename, board, image and profile names from "WMR300" to "WMR-300" (for consistency).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46628
The following patch changes dts filename and profile name for Aigale Ai-BR100 (for consistency).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46624
Official names for RT5350F based OLinuXino products are "RT5350F-OLinuXino{,-EVB}" as on official manufacturer website.
The following patch:
* changes board names from "olinuxino-rt5350f{,-evb}" to "rt5350f-olinuxino{,-evb}"
* changes filenames of dts and profile files
* changes image filenames
for Olimex RT5350F-OLinuXino{,-EVB} devices.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46623
The following patch changes:
* board name from "wl341v3" to "wl-341v3"
* dts filename
* LED names in dts file
for Sitecom WL-341v3 device.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46622
The following patch:
* changes board name from "argus-atp52b" to "atp-52b"
* changes dts filename
* fixes LED names in dts file and base-files scripts
* removes manufacturer name from image filename
for Argus ATP-52B device.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46621
This patch removes manufacturer from Belkin F7C027 image name ("belkinf7c027" -> "f7c027").
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46620
Other Asus RT-N dts files are named "RT-N..." (not "RTN..."), so use the same for RT-N56U.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46619
The following patch:
* changes board name from "xiaomi-miwifi-mini" to "miwifi-mini"
* changes filenames of dts and profile
* fixes LED names in dts file and base-files scripts
* removes manufacturer name from image filename
for Xiaomi MiWiFi Mini device.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46617
This patch:
* fixes typo (rp_n53 -> rp-n53) in Asus RP-N53 image name
* removes manufacturer from image names for Lenovo Y1{,S} devices
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46616
There are other Asus boards supported in ramips target, so use the same naming scheme for WL-330N{,3G} boards and their dts files.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46615
There is another Zbtlink board (ZBT-WA05) supported in ramips target, so use the same naming scheme for ZBT-WR8305RT board and its dts file.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46614
STORYLiNK SAP-G3200U3 is an AC1200 router based on MT7621AT+MT7602EN+MT7612EN.
It has 128MB DDR3, 8MB NOR FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.
Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons
* ethernet switch and USB diag LEDs
* UART
* GPIOs
Tested and not working:
* LEDs for WiFi radios (connected with WiFi chips, not supported in mt76?)
* failsafe mode (known problem, needs workaround like other MTK based devices)
More information in Wiki: http://wiki.openwrt.org/toh/storylink/sap-g3200u3
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46454
This patch add support for Planex MZK-DP150N.
a mini router on the MT7620A SoC with one Ethernet port and a 802.11n 2.4 GHz radio.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 46405
Adding support for OY-0001 Wireless Router.
OY-0001 is a wireless router made by oyewifi.com. Below is the details:
MT7620A, 128MB DDR2, 16MB FLASH, SD Slot, USB 2.0, 4 x LAN + 1 x WAN.
Signed-off-by: Tom Deng <2579131212@qq.com>
SVN-Revision: 46349
This patch adds support for the Linksys RE6500 Range Extender
http://wiki.openwrt.org/toh/linksys/re6500
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46043
This patch is for PandoraBox PBR-M1 which is based on mt7621,
all the features work fine, including rtc, leds, button, usb3.0, etc.
Signed-off-by: tymon <banglang.huang@foxmail.com>
SVN-Revision: 46041
Version 2 : White spaces and alphabetical order problems
fixed
Support for Olimex RT5350F-OLinuXino Boards, tested with RT5350F-OLinuXino and RT5350F-OLinuXino-EVB boards. More Info :
https://www.olimex.com/Products/OLinuXino/RT5350F/RT5350F-OLinuXino/open-source-hardware
Signed-off-by: Dimitar Gamishev HeHoPMaJIeH <gamishev@gmail.com>
SVN-Revision: 45902
MR-102N is a RT3050F based wireless router(32M RAM + 8M NOR flash) with 1 USB
and 1 ethernet port. The original product information can be found at:
http://www.aximcom.com/en/MR-102N
Signed-off-by: Tai-hwa Liang <atliang@gmail.com>
SVN-Revision: 45724
This patch adds support for Comfast CF-WR800N, a wall-plug wireless router
based on the MT7620N SoC with one Ethernet port and a 802.11n 2.4 GHz radio.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 45722
MicroWRT is an wireless router with 2 USB,1 ethernet port. It
has a 16M flash and 64M DDR2 RAM. You can use most interface, such as
i2c, SPI, i2s and PCIe. Besides that there are three expansion borad to
combine with the core board. The detailed information, please refer to
https://www.microduino.cc/wiki/index.php?title=Main_Page
This patch adds support for it.
Because there is only one port,so disabled VLAN and use eth0 as lan
port. and only a power LED control by power pin.
Signed-off-by: 盛凯 <shengkai81@gmail.com>
SVN-Revision: 45331
ZTE Q7 is a wireless router with SD Card,USB,1 ethernet port and a battery.It used MT7620a SoC.
I can,t find any information about this router on ZTE's website.
But I found this : http://en.cctairmobi.com/plus/list.php?tid=40
This router is the same as ZTE Q7 and later I found that both routers are made by the same company:-D
This patch adds support for it.
Because there is only one port,I disabled VLAN and use eth0 as lan port.
I could only create a sysupgrade firmware because I don't know how the orignal webpage check the uploaded image:-(
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 45208
I got work with this patch.
Ethernet switch (includes VLAN), WiFi connected via PCIe, LEDs, buttons.
In mtd partion map of DTS file, I renamed Linux firmware regions (kernel + root squashfs) to “firmware”because it allows kernel to split kernel and roots and rootfsdata.
signed-off-by: ngc@ff.iij4u.or.jp
——
——
SVN-Revision: 44470
This patch adds support for Xiaomi MiWiFi Mini, a 802.11a/b/g/n/ac dual radio
wireless router based on the MediaTek MT7620a SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44238
This adds support for a rt5350-based "portable nas" solution
from Intenso. The board comes with 32M RAM and 8M Flash, the
built-in HDD is connected/accessible via a usb3.0<->sata
bridge VLI VL701.
The device has 1 Ethernet port (100M/10M), 1 micro b usb 3.0
socket (for charging the battery, or accessing the hdd directly).
Wireless connectivity is provided by the rt5350 SoC [i.e.:
802.11n 1x1 2.4 GHz with a pcb antenna.]
Serial, leds, wifi, ethernet and usb are tested and
as far as I can tell: they are working fine (tm).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44001
Aigale Ai-BR100 is a router with mt7620a soc.
There are only 2 lights on the board (WAN and WLAN) so I used the wlan light as the status led.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 43681
This is a RT2880-based board, 32MB RAM, 4MB flash. The bootloader
is a hacked u-Boot that reads an LZMA image directly, so we skip
generating the uImage header and enable the lzma mtdsplit parser.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43153
(Reposted due to an issue with the patchwork server during original submission)
Unbranded. Silkscreen on PCB is “A5-V11”, believed to be made by Bococom (or at least uses Bococom image encryption - as used on poray devices - but different key)
Signed-off-by: Gareth Bryan <gareth@mx9.org>
SVN-Revision: 43102
7Links PX-4885 (clones) can also be purchased with 8MB flash.
Creating images for these routers, use dtsi for common part
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 42892
Provides support for the Tripmate HT-TM02 personal router including LEDs and
reset button. “Mode” switch is not supported. New profile includes full set
of packages required to enable LEDs, USB, and LUCI. Patches were applied
against trunk snapshot r42649. Functionality has been tested in AP, basic wifi
client, wifi router, and routed client modes - all good.
Signed-off-by: Ron Curry <wingspinner@gmail.com>
SVN-Revision: 42785
Lenovo AC1200 series has two types, Y1 and Y1S.
Y1S has 256MB DDR2, Y1 only has 128MB and Y1 have no Giga Port.
Signed-off-by: Lintel <lintel.huang@gmail.com>
SVN-Revision: 41961
This is based and tested on VoCore Alpha, but other stuff like status/eth LEDs are present on the final board revision + VoDock.
All GPIOs are exported, except spi/i2c.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 41939
This patch adds support for the Kingston Mobilelite Wireless (MLW-221)
http://wiki.openwrt.org/toh/kingston/mlw221
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 41841
generate sysupgrade image by combine two images.
one is kernel image with seama header.
another is root fs image.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 40922
It is base on rt3662 soc with dual band 802.11n
wireless router. Use rtl8367R switch chip.
This patch adds a profile for this board.
It use seama image header. so i also enable it
on kernel config.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 40908
Hi Hartmut,
Thanks for your feedback, I have reformated the patch accordingly.
Added support for Teltonika RUT5XX hardware.
Signed-off-by: Steffen Weinreich <steve@weinreich.org>
SVN-Revision: 40907
The 7Links PX-4885 is a small battery-powered wireless router.
It is based on a RT5350F WiSoC and features one ethernet port and one
USB port. It is a Hame MPR-A1 clone, except it has different GPIOs,
a different battery and more RAM (32 MB).
This patch adds a profile for this board, the corresponding device tree
file and the adequate base-files changes (incl. sysupgrade).
Signed-off-by: Hugo Grostabussiat <bonstra@bonstra.fr.eu.org>
SVN-Revision: 40554
added dts file and userspace scripts modified to support Asus RT-N14U board
current support status:
usb works
ethernet works
buttons reset, wps
leds asus:blue:[usb|lan|wan|air|power]
i2c not tested
uart not tested
wifi not yet
Signed-off-by: Pavel Löbl <lobl.pavel@gmail.com>
SVN-Revision: 39163
The TEW-692GR images are missing since r36169. Uncomment
the board specific macro in image/Makefile, in order to
generate those again.
Only build tested. No idea if the the image works or not,
I have bricked my TEW-692GR a few months ago.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38603
This commit adds the basic elements to support Poray brand routers.
It contains a tool to do the encryption/obfuscation that is used in
Poray routers.
Support for Poray devices was worked on by:
Felix Kaechele <heffer@fedoraproject.org>
Luis Soltero <lsoltero@globalmarinenet.com>
Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
SVN-Revision: 37635
r37505 add support for Huawei HG255D, but it only tested under a community hacked u-boot ("lintel u-boot"), which has a different mtd layout compared to origin one. If you install it on a box with origin u-boot, the origin factory part will be destroyed, and your wifi interface will never up!!!
This patch shrink firmware part in mtd layout to exclude origin factory part, and I will prepare another patch to fix the eeprom extract issue for box with origin u-boot.
Signed-off-by: Leon Xu <ylxu72@gmail.com>
SVN-Revision: 37530
HG255D is a kind of popular low-end home gateway in China, this patch bring the the trunk support for it. It is adapted from a local Chinese community (www.right.com.cn), so credit should given to them.
This patch is tested to work except trivial LED issues.
Signed-off-by: Leon Xu <ylxu72@gmail.com>
SVN-Revision: 37505
In order to support both normal images and initramfs, ensure that each
target sets KERNELNAME properly so that the generic kernel building code
can copy the corresponding files over $(KDIR) with the appropriate
extension. Update the various paths to the kernel and wrapper images
from $(LINUX_DIR)/arch/$(ARCH)/boot/$(foo) to $(KDIR)/$(foo).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 37049
This patch adds support for HAME MPR-A2 router using a DTS file.
The platform is Ralink RT5350.
http://wiki.openwrt.org/toh/hame/mpr-a2
Signed-off-by: Dmitry Shmygov <shmygov@rambler.ru>
SVN-Revision: 36898
Prior to the switch to 3.8, ALL5002 and ALL5003 boards shared mach-all5002.c.
With the change to DTS, this is no longer accurate, as ALL5002 is based on
Rt3352 SoC while ALL5003 is based on Rt5350 SoC, therefore the corresponding
rt5350.dtsi need to be included for ALL5003.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
Patchwork: http://patchwork.openwrt.org/patch/3557/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36435
This board uses a TrendChip SOC with its own RAM/Flash for ADSL support.
We know both SOCs are connected through ethernet and use some kind of protocol for UART communication, but due to the lack of GPL sources we couldn't get it to work. For this reason the network is configured only for LAN.
There are two versions (Chile 8MB and Spain 16MB).
Wiki: http://wiki.openwrt.org/toh/alpha/asl26555
Signed-off-by: Esteban Benito <estebanjbs@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3571/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36433
prepare_generic_squashfs was called twice on the generated images breaking mount_root
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36349
Add Netgear WNCE2001.
This is a small RT3052 device with 4MB spi flash and 32MB ram.
2 built-in antennas, 1x fastE, no USB, reset & wps switch.
On my model the AP/RT switch is unpopulated, but I verified the gpio
mapping for it.
The stock firmware is running an unprotected tftpd which allows you
to read any file from the filesystem.
Serial port is present on testpads (See image on the wiki page).
There are more testpads below the shield near the SoC, which
may have JTAG.
Slight annoyance: The bootloader is checksumming kernel&rootfs, but
can be tricked by zeroing checksum and length fields in the checksum
partition, see
target/linux/ramips/base-files/lib/preinit/04_disable_wnce2001_flash_checksumming
The manufacturer image is very similar to the DAP one, so I slightly
modified mkdapimg to support generating it.
The resulting
openwrt-ramips-rt305x-wnce2001-squashfs-factory-(worldwide|northamerica).bin
can be used to flash from stock to OpenWRT using the stock firmware
upgrade function, without using the serial port.
http://www.netgear.com/landing/wnce2001.aspxhttp://wiki.openwrt.org/toh/netgear/wnce2001
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 36289
Factory image should be used to flash from
original firmware.
[juhosg: use the GENERIC_4M template]
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35246
These targets need custom image names specified in the uImage header.
MkImage accepts an optional 4th argument to do exactly that. Reuse the
facility to generate factory images.
Compile-tested, the generated files inspected with "file" utility.
[juhosg:
- keep the factory.bin images to avoid users confusion,
- use GENERIC_4M template for the W306R V2.0
- update commit log]
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35243
This becomes crucial when you are using a generic profile to build an image
larger than 4M, e.g. for w502u.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 35238
This patch introduces OpenWRT support for the base Hauppauge/PCTV Broadway
platform. It doesn't deal with the TV tuner or transcoder at this point,
but the core functionality is working (Ethernet, wireless, USB, buttons,
LEDs, etc).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
SVN-Revision: 34595
This should fix the stalled irq problem seen by several people.
This is not the real fix, but rather moves the bug to the un/init patch of the driver.
The real bug still needs to be fixed, but this workaround should be suffcient to make
the ethernet stable.
SVN-Revision: 34177
The new version of the ALL0256N now got 8MB SPI NOR flash instead of 4MB.
In order to expose the whole amount of flash, add another image which contains
the corresponding GENERIC_8M mtdparts.
[juhosg: change suffix from '8m' to '8M']
Patch by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 33614
Add support for 8devices Carambola dev board.
The Carambola is a small RT3050-based development board with two
ethernet ports, on-board chip antenna, usb and plenty of accessible
gpio ports, sold by 8devices.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 33303
Generate image for the ALL0239-3G which can be flashed through the
chipset-vendor SDK based firmware's web-interface and bootloader.
The bootloader seems to ignore uImage checksum errors, but does complain about
them once the 0xDEADC0DE was replaced by an actual JFFS2 page.
I'm working on implementing fixtrx for uImage in the mtd package to solve this.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 33206
rt2x00 still needs some patching as the radio doesn't come to life.
Installation via webflash.
[juhosg: fix whitespace issues, remove rt305x_register_usb
from machine setup because the board has no USB port]
Signed-off-by: Mikko Hissa <mikko.hissa@uta.fi>
SVN-Revision: 33205
D-Link's DIR-620 allows to flash a uImage directly from its web-interface but
for that the image name should be set to DIR_620.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 33143
Full functionality runtime tested, installation via OEM web-interface requires
a follow-up patch.
Thanks go to Sergey Vasilyugin for his patch that pointed me at the missing
bits (including the antiparallel wps led).
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 33142
The initial support for the D-Link DAP-1350.
USB related functionality is not tested.
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 32821
This patch adds support for the Korean made Petatel PSR-680W Wireless CDMA Router.
The platform is based on Ralink RT3052.
http://wiki.openwrt.org/toh/petatel/psr-680w
Signed-off-by: Dmitry Shmygov <shmygov at rambler.ru>
SVN-Revision: 32450
Fixed: GPIO typos and confirmed GPIO_BUTTON_RESET
Fixed: Lan & Wan reversed: swaped "eth0.2" with "eth0.1" by
removing a line(default is correct), and reversed the
Lan/wan layout LLLLW to WLLLL.
Added: image/Makefile now builds -factory.bin files. I am
unsure of the accepted way to change the makefile but
the name of the image needs to be 'linkn Kernel Image'
in order to be accepted by the OEM firmware.
Known issue: eth0 (internal switch i think has mac address:
00:11:22:33:44:55 but i think it should be same as
the lan).
Known issue: Pressing the reset button has no noticable effect,
i would expect the router to boot failsafe if being
pressed on boot, reboot if short press and reset all
to default if long press.
[juhosg: remove mtdlayout_W306R and use mtdlayout_4M instead]
Signed-off-by: David Pearce <david_18051985@hotmail.com>
SVN-Revision: 31557
Make serial console for DIR-300-B1 work again.
With some recent change, "console=ttyS1,57600" was removed from the
default kernel command line, this adds the necessary mkcmdline
incantation to image/Makefile to add it there for this target.
This is quite likely broken for other targets as well.
Without this the console switches to ttyS0 instead of ttyS1 and
kernel output is missing, and the userspace comes up with 9600 baud
instead of 57600.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 31556
This patch adds support for the ASUS WL-330N3G
Comparing to the WL-330N, It have 32MB ram, usb support and a bicolor led.
The bi-color led is driven by 2 gpio.
I don't know how to handle this, so I simply made 2 leds : one red, one blue.
But the red light takes precedence over the blue one according to the chart below.
r = led is red
b = led is blue
0 = led is off
xy= x->r for red, b for blue led, y->value of brightness in /sys/class/leds/x/brughtness
initial state action led gpio state
r0 b0 r0->r1 r r0 b0
r0 b0 b0->b1 b r0 b1
r1 b0 r1->r0 0 r0 b0
r1 b0 b0->b1 r r1 *b1*
r1 b1 r1->r0 b r0 b1
r1 b1 b1->b0 r r1 b0
r0 b1 r0->r1 r r1 *b1*
r0 b1 b1->b0 0 r0 r0
Signed-off-by: Frédéric Leroy <fredo@starox.org>
SVN-Revision: 31450
More device info at: http://wiki.openwrt.org/toh/tenda/w306r
Signed-off-by: David Pearce <David_18051985@hotmail.com.au>
[juhosg: fix checkpatch errors, remove kmod-phy and luci-ssl packages
from the profile, change broken GPIO number]
SVN-Revision: 31396
[juhosg: fix indentation in platform scripts, and remove debug
messages from 06_set_iface_mac]
Signed-off-by: Patrick van Staveren <trick@vanstaveren.us>
SVN-Revision: 30808
This patch adds support for the Accton WR6202 Mini 3G broadband router.
Full details for this device are available at
http://www.awbnetworks.com/products03.php?Fullkey=19.
This device is identical to the SMCWBR11S-3GN:
http://www.smc-asia.com/products03.php?Fullkey=210
It's also worth noting that this board has a GPIO line to control the
power to the USB port.
[juhosg:
- fix checkpatch warnings,
- reorder Kconfig entry,
- merge the sysupgrade patch,
- add GPL header]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
SVN-Revision: 30434
This patch adds support for the Sitecom WL-341 v3 and other Sercomm
IP1006RRv2 based boards for sysupgrade support and for the initial
flash through pushbutton initiated recovery mode with the special
partition table and fixes for the quirks and things required by the
modified bootloader.
There is a known bug, Wi-Fi is not working on my board probably
because of the lack of RAM (the board only has 16MiB ram -- half of
the normal amount for non rebadged versions, but there is an empty
slot for another ram chip,) but I don't know for sure. The driver
loads but hostapd fails to load so I think it's not related to the
specific device except for the lack of RAM.
Moreover, only 7 of the 11 onboard leds are confirmed working, it
seems that one of the others is always on and the remaining ones are
connected to the wireless card leds already recognized by OpenWrt
[juhosg: reordered some parts in order to keep things sorted
alphabetically]
Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com>
SVN-Revision: 29910
This add support for the Sitecom WL-351 v1 002.
In principle the Engenius ESR9850 should also work with this, but I
don't have the hardware to test it.
Since an external gigabit switch (RTL8366RB) is used,
I had to modify the ramips_esw driver to add a 'bypass' mode, which
just configures it to not filter the vlan tags.
Also two initialization words (FCT2 and FPA2) are set to different
values by u-boot than what the driver is using and it only seems to
work correctly when they not overridden by the driver, so I
added them to the platform specific data as reg_initval_fct2 and
reg_initval_fpa2.
With this wired lan works as expected, however I'm still having some
trouble with the wireless lan:
It only works after I rmmod & re-insmod rt2800pci and then
reconfigure it in the webinterface, but not directly after
rebooting.
The symptom of this is wpad saying:
Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: associated (aid 1)
Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> WPA: pairwise key handshake completed (RSN)
Dec 20 15:45:22 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: authenticated
But wpa_supplicant on the client saying:
Authentication with <wl351mac> timed out.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 29604
This patch adds support for the Omnima MiniEMBWiFi
Ralink RT3050F based board.
Based on a patch by Ivan Ignjatic <ivan at omnima.co.uk>
SVN-Revision: 29533
The preconfiguration of the USB LED has benn move to the
/etc/uci-defaults/leds script. [juhosg]
Signed-off-by: Adam Porter <porter.adam at gmail.com>
SVN-Revision: 28571
This patch adds initial board support for the MoFi Network MOFI3500-3GN
(Ralink RT3052F SoC, 8MB flash, 32MB ram, wireless N, USB-OTG). This
router is basically the NA version of the HW550-3G.
Signed-off-by: Layne Edwards <ledwards76@gmail.com>
SVN-Revision: 26466
This patch adds initial support for the Aztech HW550-3G (Ralink
RT3052f SoC, 8MB flash, 32MB dram). Ethernet is not working yet.
Wireless appears to work fine. USB does not work yet (as with other
Ralink boards).
Signed-off-by: Layne Edwards <ledwards76@gmail.com>
SVN-Revision: 26123
The attached patch adds a preliminary support for Prolink PWH2004 board
(Ralink RT305x based). LAN and flash appear to work. However, the USB
port and WLAN I have not managed to activate properly yet, but that
problem appears to be present with other rt305x targets as well(?).
Signed-off-by: Esa Hyytia <esa at netlab.tkk.fi>
SVN-Revision: 23129
This patch adds support for Sparklan WCR-150GN board.
Network configuration should be tweaked to make it work fully. The
reason it's not in this patch is that ramips target should be modified
to support different /etc/config/network files for different boards.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 22658
When trying to build images with jffs2 filesystem for ramips platform
there is only one jffs2 image produced instead of two (64k and 128k).
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 22435