The Toshiba TC58NVG0S3HTA00 is detected with 64 byte OOB while the flash
has 128 byte OOB. This adds a static NAND ID entry to correct this.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
This workaround will allow the MA5671A to function, ignoring the
persistently asserted tx-fault.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
(added 5.15 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ubiblock devices should be used on NAND flash to store the uImage.FIT
in case the bootloader supports that -- otherwise only rootfs is stored
in UBI while the uImage.FIT contains only the kernel and dtb.
Hence there is no need to enable parsing partitions on NAND mtdblock
devices, it is even responsible for the ugly warning on-opening of the
mtdblock device now. Just don't do it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of warning loudly about mtdblock devices being created, rather
just warn if they are actually used.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The commit "uboot-mediatek: replace patch with accepted commit" changed
the name of the boot configuration property from 'bootconf' to
'u-boot,bootconf'. Reflect this change in the FIT partition parser.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MPLS feature symbols are normally only set when kmod-mpls is enabled, but the
CONFIG_MPLS symbol they depend on could also have been selected by openvswitch
instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is required to support built-in modem of ZTE MF286R, in addition to
other external modems, such as MF831, MF910, MF920, which refuse to
reconfigure their remote MAC address, even if "locally administered" bit
is set, leading to dropped traffic towards the host. Add a workaround
for that issue already present in cdc_ether to rndis_host driver as
well.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
The prerequisite DSA changes for the nice RTL8366RB improvements
are already backported so bring back these changes as well.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit add some enabled symbols to generic config.
LTO is only supported by clang compiler and therefore should
be disabled in the generic config instead of duplicating this
symbol in each target. CONFIG_LTO_NONE do this job.
The second group of symbols is enabled by the options available
in the generic config and is therefore added here:
* CONFIG_AF_UNIX_OOB is selected by CONFIG_NET && CONFIG_UNIX,
* CONFIG_BINARY_PRINTF is selected by CONFIG_BPF_SYSCALL,
* CONFIG_NET_SOCK_MSG is selected by CONFIG_BPF_SYSCALL && CONFIG_NET.
The other symbols are disabled and should be in the generic config.
This commit also removes these symbols from subtargets.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
There are various reports on Github and in the forum that this commit
causes multiple problems.
This reverts commit ee6ba216d8.
Fixes: #9420
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Use the kernel's built-in formula for computing this value.
The value applied by OpenWRT's sysctl configuration file does not scale
with the available memory, under-using hardware capabilities.
Also, that formula also influences net.netfilter.nf_conntrack_buckets,
which should improve conntrack performance in average (fewer connections
per hashtable bucket).
Backport upstream commit for its effect on the number of connections per
hashtable bucket.
Apply a hack patch to set the RAM size divisor to a more reasonable value (2048,
down from 16384) for our use case, a typical router handling several thousands
of connections.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Backports following fix:
hv: utils: add PTP_1588_CLOCK to Kconfig to fix build
The hyperv utilities use PTP clock interfaces and should depend a
a kconfig symbol such that they will be built as a loadable module or
builtin so that linker errors do not happen.
Prevents these build errors:
ld: drivers/hv/hv_util.o: in function `hv_timesync_deinit':
hv_util.c:(.text+0x37d): undefined reference to `ptp_clock_unregister'
ld: drivers/hv/hv_util.o: in function `hv_timesync_init':
hv_util.c:(.text+0x738): undefined reference to `ptp_clock_register'
References: https://lore.kernel.org/stable/20220328093115.7486-1-ynezz@true.cz/T/#u
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Using set_disk_ro() doesn't have the desired effect and instead of
just setting the single partition to be read-only it affects the
whole disk. Use the bd_read_only flag in struct block_device instead
to mark a partition being read-only.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport patch
8b6836d82470 ("net: dsa: mv88e6xxx: keep the pvid at 0 when VLAN-unaware")
from 5.15.
Keeping the pvid at 0 when VLAN-unaware makes it possible to drop the
hack introduced in commit 920eaab1d8 ("kernel: DSA roaming fix for
Marvell mv88e6xxx"). Dropping the hack makes it possible to use VLAN
interfaces with VID 1 on DSA ports without problems with FDB.
Signed-off-by: Marek Behún <kabel@kernel.org>
There are 2 warning for ar8xxx swconfig.
- Fix not used dev variable when ETHERNET_PACKET_MANGLE
is not selected
- Convert fallthrough comment to compilation macro
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Backport qca8k mdio improvement patch merged upstream,
where we use eth packet when available to send mdio commands.
This should improve speed and cause less load on the CPU.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Prepare uImage.FIT partition parser for Linux 5.15
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Patches that add the additional AQR PHY ID-s is just copy/paste from 5.10
and kernel 5.11 dropped the ack_interrupt method for PHY IRQ handling,
instead handle_interrupt is used.
So, simply switch to using handle_interrupt like other upstream AQR PHY-s.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
After fixing the original 720 patch, it looks like more were added for
additional AQR ID-s.
Patches that add the additional AQR PHY ID-s is just copy/paste from 5.10
and kernel 5.11 dropped the ack_interrupt method for PHY IRQ handling,
instead handle_interrupt is used.
So, simply switch to using handle_interrupt like other upstream AQR PHY-s.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Standardize pending patch tcp_no_window_check patch as with
new kernel they added a check for global variables.
The 2 new condition are that they must be read-only or
the data pointer should not point to kernel/module global
data.
Remove the global variable and move it to a standard place
following other variables logic.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Rework hack patch in dir for kernel 5.15.
For the specific patch of packet mangeling introduce a new extra_priv_flags
as we don't have enough space to add additional flags in priv_flags.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Refresh qca8k backport patches for 5.15 kernel.
Vlan_prepare is now dropped and there were some changes
to vlan add/remove functions.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
In commit ab143647ef ("kernel: generic: improve FIT partition parser")
part_bits was bumped to 2 in order to allow up to 3 additional FIT
sub-images mapped into sub-partitions.
This change has to be reflected also in our local patch
420-mtd-set-rootfs-to-be-root-dev.patch
which still assumed part_bits==1 for mtdblock devices in case of
CONFIG_FIT_PARTITION=y.
Fixes: #9557
Fixes: ab143647ef ("kernel: generic: improve FIT partition parser")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
# CONFIG_PSTORE_COMPRESS_DEFAULT="deflate"
this can lead to confusion. Thankfully, in the KConfig
world this setting is still interpreted as disabled.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
at91/sama7 fails to build due to:
| Asymmetric (public-key cryptographic) key type (ASYMMETRIC_KEY_TYPE) [Y/?] y
| Asymmetric public-key crypto algorithm subtype (ASYMMETRIC_PUBLIC_KEY_SUBTYPE) [Y/?] y
| Asymmetric TPM backed private key subtype (ASYMMETRIC_TPM_KEY_SUBTYPE) [N/m/?] (NEW)
|Error in reading or end of file.
please note that asym_tpm (module) has been removed in 5.17:
<https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=d3cff4a9>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ARM Builds like sunxi/cortexa53 or the rpi family failed
to build due to a new symbols showing up:
|Google Firmware Drivers (GOOGLE_FIRMWARE) [Y/n/?] y
| Coreboot Table Access (GOOGLE_COREBOOT_TABLE) [M/n/y/?] m
| Coreboot Framebuffer (GOOGLE_FRAMEBUFFER_COREBOOT) [N/m/?] (NEW)
|Error in reading or end of file.
Fixes: e5b009e532 ("kernel: Package GOOGLE_FIRMWARE drivers")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit moves the patches for the r8152.c driver to the generic
directory. Previously they were only available on the bcm27xx target.
With these patches the Realtek RTL8153C, RTL8153D, RTL8156A and RTL8156B
chips are supported on all targets by the kmod-usb-net-rtl8152 module.
The RTL8156A and RTL8156B are the 2.5Gb/s Ethernet adapters.
The patches have been tested on TP-Link UE300 (RTL8153A) and UNITEK
1313B (RTL8156B).
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* only map filesystems configured in 'loadables'
* allow mapping more than one filesystem (e.g. customization/branding
or localization in addition to rootfs)
* small cleaning here and there
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If the selected boot configuration is stored by U-Boot in '/chosen'
node as 'bootconf' attribute, use that configuration to resolve the
block device used as rootfs. Fall back to use the default configuration
in case 'bootconf' is not present.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove "a" character from the first line of patch
738-v5.14-01-net-dsa-qca8k-fix-an-endian-bug-in-qca8k-get-ethtool.patch
Otherwise `git am` fails to apply this patch which is annoying when
trying to do some development / rebasing.
Signed-off-by: Marek Behún <kabel@kernel.org>
As the upcoming release will be based on Linux 5.10 only, remove all
kernel configuration as well as patches for Linux 5.4.
There were no targets still actively using Linux 5.4.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kernel 5.6 introduced a new config symbol SERIAL_8250_16550A_VARIANTS.
In kernel 5.8, this symbol was changed to default to on on !x86, as some
embedded devices still use 16650A variants. Let's play safe here and
enable this symbol in the generic config, to avoid others from running
into this problem and having to spend several hours trying to bisect
this problem. While we could disable the symbol in the x86 target
configs, a 20ms boot time reduction really isn't worth the time wasted
on bisecting this issue.
Matt discovered this problem while working on adding support for the
WatchGuard Firebox M200 to the qoriq target, where it caused some
characters to be missing on the console output.
Reported-by: Matt Fawcett <mattytap@icloud.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
Seeing failure to build because of missing symbols related to provisioning
CONFIG_KEXEC and signed images. Without this, if you set
CONFIG_KERNEL_KEXEC=y and try to build, target/linux will hang at:
scripts/kconfig/conf --syncconfig Kconfig
...
kexec system call (KEXEC) [Y/n/?] y
kexec file based system call (KEXEC_FILE) [Y/n/?] y
Verify kernel signature during kexec_file_load() syscall (KEXEC_SIG) [N/y/?] (NEW)
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Backport patches
381a730182f1 ("net: dsa: Move VLAN filtering syncing out of dsa_switch_bridge_leave")
108dc8741c20 ("net: dsa: Avoid cross-chip syncing of VLAN filtering")
from upstream (currently in net-next) to fix null-pointer dereference.
Signed-off-by: Marek Behún <kabel@kernel.org>
Add patch found in Teltonika RUT9_R_00.07.01.4 GPL SDK download[1]
adding USB IDs of the MeigLink SLM750 to the relevant kernel drivers.
Newer versions of Teltonika's 2G/3G/4G RUT9XX WWAN router series come
with this kind of modem.
[1]: https://wiki.teltonika-networks.com/view/GPL
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch adds a patch to allow using parser_trx from ramips target,
mainly for Buffalo devices.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This patch moves the patches of parser_trx in mediatek target to
generic/backport-5.10 to use the changes from ramips target and
backport the additional patch of the parser.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The XMC XM25QH128C is a 16MB SPI NOR chip. The patch is verified on Ruijie RG-EW3200GX PRO.
Datasheet available at https://www.xmcwh.com/uploads/435/XM25QH128C.pdf
Signed-off-by: Langhua Ye <y1248289414@outlook.com>
the Aerohive HiveAP-330 and HiveAP-350 come equipped
with an TI TMP125 temperature chip. This patch wires
up the necessary support for this sensor and exposes
it through hwmon / thermal sensor framework. Upstream
support is coming, but it has to go through hwmon-next
first.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The last remaining 5.4 target currently chokes because the
symbols haven't been disabled like for 5.10.
Fixes: 97158fe10e ("kernel: package ramoops pstore-ram crash log storage")
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Add the following kconfig symbols (disabled):
CONFIG_DEFAULT_FQ
CONFIG_DEFAULT_CODEL
CONFIG_DEFAULT_SFQ
Also resort the config with the kconfig.pl script.
Fixes: f39872d966 ("kernel: generic: select the fq_codel qdisc by default")
Tested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Package the ability to log kernel crashes to 'ramoops' pstore
files into RAM in /sys/fs/pstore
Reference to the ramoops admin guide in upstream Linux:
https://www.kernel.org/doc/html/v5.10/admin-guide/ramoops.html
The files in RAM survive a warm reboot, but not a cold reboot.
Note: kmod-ramoops selects kmod-pstore and kmod-reed-solomon.
The feature can be used by selecting the kmod-ramoops and
adding a ramoops reserved-memory definition to the device DTS.
Example from R7800:
reserved-memory {
rsvd@5fe00000 {
reg = <0x5fe00000 0x200000>;
reusable;
};
ramoops@42100000 {
compatible = "ramoops";
reg = <0x42100000 0x40000>;
record-size = <0x4000>;
console-size = <0x4000>;
ftrace-size = <0x4000>;
pmsg-size = <0x4000>;
};
};
If no definition has been made in DTS, no crash log is stored
for the device.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(added CONFIG_EFI_VARS_PSTORE disable)
Add the missing IPv6 flow offloading support for routing only.
Hardware flow offloading is done by the packet processing engine (PPE)
of the Ethernet MAC and as it doesn't support mangling of IPv6 packets,
IPv6 NAT cannot be supported.
Signed-off-by: David Bentham <db260179@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
flowtable->net was initialized too late, and this could be triggered even
without hardware offload support on the device
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The issue of EAP frames sent to group address (or the wrong address) has been
addressed in mac80211, so this hack is no longer needed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This caches flows between MAC addresses on separate ports, including their VLAN
in order to bypass the normal bridge forwarding code.
In my test on MT7622, this reduces LAN->WLAN bridging CPU usage by 6-10%,
potentially even more on weaker platforms
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Had to update generic defconfig (make kernel_menuconfig CONFIG_TARGET=generic)
for this bump, but since that only modifies the target defined in .config,
and since that target also needed to be updated for unrelated reasons, manually
propagated the newly added symbol to the generic config.
Removed upstreamed:
pending-5.10/860-Revert-ASoC-mediatek-Check-for-error-clk-pointer.patch[1]
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.99&id=080f371d984e8039c66db87f3c54804b0d172329
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <graysky@archlinux.us>
Support MT7530 PHY link change interrupts, and enable for MT7621.
For external MT7530, a GPIO IRQ line is required, which is
board-specific, so it should be added to each DTS. In case the
interrupt-controller property is missing, it will fall back to
polling mode.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Add support for MediaTek Gigabit Ethernet PHYs found in MT7530 and
MT7531. Fix some link up/down issues.
The errornous check for the PHY mode which broke things with MT7531
has been removed as suggested by patch
net: phy: mediatek: remove PHY mode check on MT7531
As a result, things are working fine now on MT7622+MT7531 as well.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
The kernel configuration allows us to select a default qdisc. Let's do this for
5.10 (as 5.4 is on its way out) and get rid of the hacky patch we've been
carrying.
Acked-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
This reverts commit 8b4cba53a9.
This broke the mt7530 on Linksys e8450 (mt7622) for me.
[ 1.312943] mt7530 mdio-bus:00 lan1 (uninitialized): failed to connect to PHY: -EINVAL
[ 1.320890] mt7530 mdio-bus:00 lan1 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 0
[ 1.331163] mt7530 mdio-bus:00 lan2 (uninitialized): failed to connect to PHY: -EINVAL
[ 1.339085] mt7530 mdio-bus:00 lan2 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 1
[ 1.349321] mt7530 mdio-bus:00 lan3 (uninitialized): failed to connect to PHY: -EINVAL
[ 1.357241] mt7530 mdio-bus:00 lan3 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 2
[ 1.367452] mt7530 mdio-bus:00 lan4 (uninitialized): failed to connect to PHY: -EINVAL
[ 1.375367] mt7530 mdio-bus:00 lan4 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 3
[ 1.385750] mt7530 mdio-bus:00 wan (uninitialized): failed to connect to PHY: -EINVAL
[ 1.393575] mt7530 mdio-bus:00 wan (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 4
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit 3f4301e123.
This broke the mt7530 on Linksys e8450 (mt7622) for me.
[ 1.300554] mt7530 mdio-bus:00: no interrupt support
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Support MT7530 PHY link change interrupts, and enable for MT7621.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Add support for MediaTek Gigabit Ethernet PHYs found in MT7530.
Fix some link up/down issues.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Use hardware to forward multicast traffic instead of trapping to the
host.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Allow MTU up to 2026 on mediatek, ramips/mt7621 targets.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Backport patch ("MIPS: ath79: drop _machine_restart again"), which is
required to support GPIO restart handler on ZTE MF286, broken due to
_machine_restart being restored in kernel accidentally, wich causes any
registered restart handlers to not execute, including one from
ath79-reset driver.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
This moves bootargs-append support patch from ipq40xx and ipq806x to
generic. This way we can append additional boot arguments from DTS instead
of only being able to overwrite them.
This is a preparation for kirkwood support of ipTIME NAS1.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This fixes the following compile warning:
CC init/do_mounts.o
init/do_mounts.c:478:19: warning: 'mount_ubi_rootfs' defined but not used [-Wunused-function]
478 | static int __init mount_ubi_rootfs(void)
| ^~~~~~~~~~~~~~~~
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Flash accessing instruction templates are determined during probe since
v5.6 for spimem-dirmap support in spi-nor driver in upstream commit:
df5c21002cf4 ("mtd: spi-nor: use spi-mem dirmap API")
As a result, changing bus_width on the fly doesn't work anymore and this
patch will cause executing spi-mem ops with 3-byte address on 16-32M
flash area.
We can't easily revert that behavioral change upstream so drop the patch
to prevent u-boot and eeprom from being erased.
Fixes: b10d604459("kernel: add linux 5.10 support")
Reported-by: Frank Di Matteo <dimatto@foxmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Backport 2 patches for Armada 3720 comphy from 5.15 kernel.
These are needed for clear application of pending patches that fix this
driver.
Signed-off-by: Marek Behún <kabel@kernel.org>
Backport Aardvark PCIe controller driver changes that fix MSI support,
that were recently sent to the linux-pci mailing list [1].
These changes fix MSI and MSI-X support for this PCIe controller, which,
among other things, make it possible to use NVMe drives with this PCIe
controllers.
[1] https://lore.kernel.org/linux-pci/20220110015018.26359-1-kabel@kernel.org/
Signed-off-by: Marek Behún <kabel@kernel.org>
This does not have spare blocks for remapping, and it is also not suitable
for random write access. It only skips over bad blocks on linear writes of an
image to a partition. As such, it is really only suitable for the kernel
partition, or other partitions with mostly static data
Signed-off-by: Felix Fietkau <nbd@nbd.name>
