Commit Graph

1031 Commits

Author SHA1 Message Date
Chen Minqiang
43dad22025
uboot-mediatek: unifi6lr: mtd erase before write to flash
Erase firmware ereas before writing to recovery or production partition
when updating them via the bootloader menu.

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-04-28 20:54:43 +01:00
Daniel Golle
ebed523ee8
arm-trusted-firmware-mediatek: fix boot hang on unifi-6-lr
The Ubiquiti Networks UniFi 6 LR access point comes with a total of
512 MB RAM provided by 2x 8-bit DDR3 SDRAM. This combination lead to
problems with the DDR calibration on boot resulting in occasional hang
on boot. Use updated calibration binary provided by MediaTek to make
boot on that device more reliable.
The binary has also been tested on the BananaPi BPi-R64 board and that
also works just fine with the new binary.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-04-28 20:51:53 +01:00
David Bauer
b832ebb886 uboot-rockchip: update to v2021.04
Update the uboot-rockchip to the latest upstream release.
Remove upstreamed patches.

Tested-on: FriendlyElec NanoPi R2S

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-04-20 13:15:45 +02:00
Daniel González Cabanelas
4f8da19572 uboot-envtools: mvebu: add Buffalo LS421DE
The Buffalo Linkstation LS421DE NAS lacks an uboot env config file.

Create it via scripts.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2021-04-17 22:44:09 +01:00
Zoltan HERPAI
d6cf997bd7 uboot-sunxi: update ATF dependencies for 3 boards
Fix 3 board definitions that were missed in the process of moving
to the a64/h6 ATF blobs.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2021-04-15 00:24:50 +02:00
Zoltan HERPAI
9aa66b8ce7 sunxi: add support for Banana Pi M2 Berry
CPU: Allwinner V40 quad-core Cortex A7 @ 1.2GHz
Memory: 1GB DDR3
Storage: SDcard, native SATA
Network: 10/100/1000M ethernet, Ampak AP6212 wifi + BT
USB: 4x USB 2.0

Installation:
Use the standard sunxi installation to an SD-card.

While the board is very similar to the M2 Ultra board
(the V40 is the automotive version of the R40), as both
the u-boot and kernel supports them separately, and some
pins are different, let's add a separate device spec.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2021-04-12 14:02:02 +02:00
Daniel Golle
d0adc4865c
uboot-mediatek: minor fixes for bpi-r64 spi-nand default env
* check image checksums before writing to flash
 * only bootmenu_0...9 are working, remove bootmenu_a entry

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-04-11 22:48:36 +01:00
Zoltan HERPAI
3225241c2b sunxi: add support for H6 boards and OrangePiOnePlus
Specifications:

SoC	Allwinner H6 @ 1.8 Ghz
DRAM	1Gb LPDDR3
Power	DC 5V @ 3A
Video	HDMI (Type 2.0A - full)
Audio	HDMI, on-board microphone
Network	10/100/1000Mbps Ethernet (Realtek RTL8211)
Storage	microSD
USB	1 USB2.0 Host, 1 USB2.0 OTG
Debug	Serial UART

Flashing instructions:
 Standard sunxi SD card installation procedure - copy image to SD card,
 insert into SD card slot on the device and boot.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2021-04-11 23:14:55 +02:00
Zoltan HERPAI
c2163530db arm-trusted-firmware-sunxi: move to use the common tf-a build code and bump to latest version
Create a -a64 package for now. Moving to the latest ATF was tested on a
SoPine A64 board.

U-Boot SPL 2020.04 (Feb 19 2021 - 11:28:19 +0000)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE:  BL31: v2.4(release):reboot-15854-g42b39a13d2
NOTICE:  BL31: Built : 22:45:53, Feb 22 2021
NOTICE:  BL31: Detected Allwinner A64/H64/R18 SoC (1689)
NOTICE:  BL31: Found U-Boot DTB at 0x4090a28, model: SoPine with baseboard
NOTICE:  PSCI: System suspend is unavailable

U-Boot 2020.04 (Feb 19 2021 - 11:28:19 +0000) Allwinner Technology

CPU:   Allwinner A64 (SUN50I)
Model: SoPine with baseboard
DRAM:  2 GiB

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2021-04-11 23:14:54 +02:00
Zoltan HERPAI
c75d441f20 uboot-sunxi: add ATF variable for specifying which flavour to use
In preparation for H6 support (which requires a separate ATF blob), add
an envvar to the A64 boards specifying which ATF blob to use.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2021-04-11 23:14:52 +02:00
Daniel Golle
dcdafbfc1a
uboot-envtools: support environment in spi-nand on bpi-r64
Default to U-Boot env in UBI if root device is not mmc block device.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2021-04-11 20:19:49 +01:00
Daniel Golle
987562bad2
uboot-mediatek: add spi-nand build for bananapi bpi-r64
Some of bpi-r64 boards have serial NAND attached to SPI bus.
Build U-Boot for booting from SPI-NAND.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2021-04-11 20:19:34 +01:00
Oskari Lemmela
cd7a9909d5 mediatek: fix writing bananapi bpi-r64 env
Use generic functions to get env partition.

Fixes: 7043e4334f ("mediatek: mt7622: improve sysupgrade on MMC")
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2021-04-11 14:55:35 +01:00
Oskari Lemmela
d05051774e mediatek: bpi-r64: use separate partition for emmc bootloader
eMMC booloader is stored to separate partition.
FIP size is increased to 2MB.

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2021-04-11 14:55:35 +01:00
Piotr Dymacz
012a9aa00b uboot-envtools: oxnas: drop redundant space after case keywords
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-04-10 15:18:48 +02:00
Piotr Dymacz
7cde7d2131 uboot-envtools: layerscape: drop redundant space after case keywords
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-04-10 15:18:41 +02:00
Piotr Dymacz
6ab80b04fa uboot-envtools: ipq806x: drop redundant space after case keywords
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-04-10 15:18:32 +02:00
Piotr Dymacz
156a27eddf uboot-envtools: ipq40xx: drop redundant space after case keywords
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-04-10 15:18:27 +02:00
Piotr Dymacz
8c11597783 uboot-envtools: imx6: drop redundant space after case keywords
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-04-10 15:18:21 +02:00
Piotr Dymacz
914563e286 uboot-envtools: drop shebang from uci-defaults and lib files
These files are sourced and non-executable, a shebang is redundant.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-04-10 15:18:14 +02:00
Piotr Dymacz
8c3383799a uboot-imx6: define 'BUILD_DEVICES' for Toradex Apalis
Without 'BUILD_DEVICES' defined, the U-Boot related package won't be
automatically selected when building for Toradex Apalis device.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-04-10 15:18:09 +02:00
Piotr Dymacz
15e801041a uboot-imx6: align indent size in Makefile
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2021-04-10 15:18:04 +02:00
Piotr Dymacz
e94d1db91e uboot-imx6: drop support for Nitrogen6x/SABRE devices
These devices never got officially supported in the tree thus it doesn't
make much sense to waste our infrastructure resources and keep building
dedicated U-Boot images for them.

CC: Petr Štetiar <ynezz@true.cz>
CC: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
2021-04-10 15:17:59 +02:00
Daniel Golle
be41fd9489
uboot-envtools: add env settings for ubnt,unifi-6-lr-ubootmod
Add settings for fw_printenv/fw_setenv for the Ubiquiti UniFi 6 LR
when running OpenWrt's version of U-Boot. The settings should work
equally with the unmodified version, but that has not yet been
tested.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-04-09 16:04:51 +01:00
Daniel Golle
e9ad412049
uboot-mediatek: add build for Ubiquiti Networks UniFi 6 LR
Add U-Boot build for the Ubiquiti Networks UniFi 6 LR access point.
This allows updating the bootchain to modern ARM Trusted Firmware 2.4
and U-Boot 2021.04 while keeping as much of the existing flash layout
as possible (u-boot-env, factory and eeprom partitions are retained),
gaining robust recovery vs. production dual-boot mechanism.
Add info for the Winbond W25Q512JV SPI NOR flash used in the device
and wait for GPIOs to settle after reset before checking for reset
button.
I2C connected LED controller is not supported yet.
Writing large amounts of data to SPI flash currently doesn't work due
to watchdog timeout causing reset before data write completes.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-04-09 16:04:46 +01:00
Daniel Golle
d37aaf3ee2
arm-trusted-firmware-mediatek: increase NOR bl3 size
Use bl3 size of 0xa0000 instead of 0x80000 in NOR flash.
This results in bl3 ending at 0xc0000 which is where the legacy
bootchain typically puts U-Boot environment.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-04-09 16:04:40 +01:00
Daniel Golle
0268f76bbb
uboot-mediatek: bpi-r64: erase eMMC environment on installation
Erase U-Boot environment partition on eMMC on installation to make sure
chages are applied.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-04-09 16:04:20 +01:00
Bjørn Mork
b7154fabf0 uboot-envtools: add wrapper scripts for alternate config
Now that we can create an alternate configuration file, add two
wrapper scripts for simple access to it using the alternate
alternate application names `fw_printsys' and `fw_setsys'.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-04-08 09:20:59 +02:00
Bjørn Mork
a3e9fd7e5b uboot-envtools: add support for multiple config partitions
Most (all?) of the realtek devices have two u-boot config partitions
with a different set of variables in each. The U-Boot shell provides
two sets of apps to manipulate these:

 printenv- print environment variables
 printsys- printsys - print system information variables
 saveenv - save environment variables to persistent storage
 savesys - savesys - save system information variables to persistent storage
 setenv  - set environment variables
 setsys  - setsys  - set system information variables

Add support for multiple ubootenv configuration types, allowing
more than one configuration file.

Section names are not suitable for naming the different
configurations since each file can be the result of multiple sections
in case of backup partitions.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-04-08 09:20:59 +02:00
Daniel Golle
5e7d6d5ba4
uboot-mediatek: update to v2021.04
Remove patches merged upstream and refresh the remaining ones.
Runtime tested on
 * Bananapi BPi-R64 (eMMC and SD Card)
 * Linksys E8450 (SPI-NAND)
 * Ubiquiti UniFi 6 LR (SPI-NOR)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-04-05 18:57:51 +01:00
Daniel Golle
1db4681617 uboot-mediatek: bpi-r64: no longer force recovery on first-boot
Now that sdcard.gz image contains everything needed to boot straight
into production image, no longer force booting into recovery image on
first boot by removing the logic which implemented that.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-04-04 10:51:25 +01:00
Daniel Golle
5ea7fabdb3
uboot-mediatek: adapt root= cmdline arg for bpi-r64
Adapt to FIT partition parser changes.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-31 22:54:17 +01:00
Rosen Penev
85fa8ad8af kexec-tools: update to 2.0.21
kdump was removed in 7acd257ae67b4ca94f8c23cb8bda0ee0709b9216

gdb can be used as an alternative.

Remove autoreconf. It's not needed as the configure files are already
generated.

Remove upstreamed patch.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2021-03-19 01:25:26 +01:00
Daniel Golle
81edc842f6
uboot-mediatek: don't rely in 'lzma' cmdline
Use 'xz --format=lzma' instead.
Fixes build for mt7629.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-18 04:19:48 +00:00
Hauke Mehrtens
0e3f6fbe10 mediatek: Fix writing U-Boot env on Buffalo WSR-2533DHP2
This fixes writing to the U-Boot environment by making the partition
writable and setting the correct flash sector size of 128K.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-17 22:39:59 +00:00
Daniel Golle
a29f71c380 uboot-mediatek: fix default environment of bpi-r64 emmc
The emmc variant used the default environment of the sdmmc variant.
Fix that.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-17 22:36:58 +00:00
Daniel Golle
41af8735d4 uboot-mediatek: bpi-r64: make use of FIT configuration selection
Allow selecting either SATA or PCIE functionality using uImage.FIT
configurations and device-tree overlays.
By default, PCIE1 is selected (as it has been before this change).
To select SATA instead, you can do this now:

fw_setenv bootconf config-mt7622-bananapi-bpi-r64-sata

and reboot.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-17 19:55:38 +00:00
INAGAKI Hiroshi
74f15628dd mediatek: add support for Buffalo WSR-2533DHP2
This adds support for the Buffalo WSR-2533DHP2.

The device uses the Broadcom TRX image format with a special magic. To
be able to boot the images or load them they have to be wrapped with
different headers depending how it is loaded.

There are multiple ways to install OpenWrt on this device.
Boot ramdisk from U-Boot
----------------------------
This will load the image and not write it into the flash.

1. Stop boot menu with "space" key
2. Select "System Load Linux to SDRAM via TFTP."
3. Load this image:
   openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-initramfs-kernel.bin
4. The system boots the image

Write to flash from U-Boot
-----------------------------
This will load the image over tftp and directly write it into the flash.

1. Stop boot menu with "space" key
2. Select "System Load Linux Kernel then write to Flash via TFTP."
3. Load this image:
   openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory-uboot.bin
4. The system writes this image into the flash and boots into it.

Write to flash from Web UI
-----------------------------
This will load the image over over the Web UI and write it into the flash

1. Open the Web UI
2. Go to "管理" -> "ファームウェア更新"
3. Select "ローカルファイル指定" and click "更新実行"
4. Load this image:
   openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory.bin
5. The system writes this image into the flash and boots into it.

Specifications
-------------------
* SoC:       MT7622 (4x4 2.4 GHz Wifi)
* Wifi:      MT7615 (4x4 5 GHz Wifi)
* Flash:     Winbond W29N01HZ 128MB SLC NAND
* RAM        256MB
* Ethernet:  Realtek RTL8367S (5 x 1GBit/s, SoC via 2.5GBit/s)

Co-Developed-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-15 17:02:17 +01:00
Daniel Golle
8dae189c7e
uboot-mediatek: also install production image to eMMC
Make installation to eMMC more convenient on the BPi-R64 by also
copying the production image (if valid) from SD Card to eMMC.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-14 22:15:47 +00:00
Daniel Golle
578c73fea3
uboot-mediatek: select matching U-Boot for board
Instead of building all U-Boot variants by default, build only those
needed by the selected board(s).

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-14 22:00:05 +00:00
Hauke Mehrtens
e6ba970b6e realtek: Add ZyXEL GS1900-8
The ZyXEL GS1900-8 is a 8 port switch without any PoE functionality or
SFP ports, but otherwise similar to the other GS1900 switches.

Specifications
--------------
* Device:    ZyXEL GS1900-8 v1.2
* SoC:       Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash:     Macronix MX25L12835F 16 MiB
* RAM:       Nanya NT5TU128M8GE-AC 128 MiB DDR2 SDRAM
* Ethernet:  8x 10/100/1000 Mbit
* LEDs:      1 PWR LED (green, not configurable)
             1 SYS LED (green, configurable)
             8 ethernet port status LEDs (green, SoC controlled)
* Buttons:   1 on-off glide switch at the back (not configurable)
             1 reset button at the right side, behind the air-vent
               (not configurable)
             1 reset button on front panel (configurable)
* Power      12V 1A barrel connector
* UART:      1 serial header (JP2) with populated standard pin connector on
             the left side of the PCB, towards the back. Pins are labelled:
             + VCC (3.3V)
             + TX (really RX)
             + RX (really TX)
             + GND
             the labelling is done from the usb2serial connector's point of
             view, so RX/ TX are mixed up.

Serial connection parameters for both devices: 115200 8N1.

Installation
------------
Instructions are identical to those for the GS1900-10HP and GS1900-8HP.

* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
  image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
  space bar, and enable the network:
  > rtk network on
* Since the GS1900-10HP is a dual-partition device, you want to keep the
  OEM firmware on the backup partition for the time being. OpenWrt can
  only boot off the first partition anyway (hardcoded in the DTS). To
  make sure we are manipulating the first partition, issue the following
  commands:
  > setsys bootpartition 0
  > savesys
* Download the image onto the device and boot from it:
  > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8-initramfs-kernel.bin
  > bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
  > sysupgrade /tmp/openwrt-realtek-generic-zyxel_gs1900-8-squashfs-sysupgrade.bin

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-14 15:07:30 +01:00
Daniel Golle
79b6a4bd3c
uboot-mediatek: import fix for AHCI and enable SATA
Import patch form Frank Wunderlich <frank-w@public-files.de> to fix
build of MediaTek AHCI SATA driver.
Enable that driver on Bananapi BPi-R64.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-13 20:16:03 +00:00
Daniel Golle
997ff740dc
uboot-mediatek: fix build on Mac OS X
Copy patch added to uboot-sunxi by commit 3cc57ba462
("uboot-sunxi: add missing type __u64") also to uboot-mediatek.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-13 13:41:04 +00:00
Daniel Golle
0183ee2eb9
uboot-mediatek: update configs for MT7622 devies
* make sure USB 2.0 works (useful for UEFI-booting eg. memtest86)
 * include more useful U-Boot config options on BPi-R64.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-12 00:18:58 +00:00
Daniel Golle
9dfc2b3ca4
uboot-mediatek: update to 2021.04-rc3 with MediaTek's patches
MediaTek published their current U-Boot patchset on github:
https://github.com/mtk-openwrt/u-boot/commits/mtksoc

Import the platform patches from there (`00-mtk-*.patch`), arrange,
them nicely, drop no longer needed local patches and rebase on top of
U-Boot 2021.04-rc3.

Tested and works well on Linksys E8450 (snand-1ddr) as well as
Bananapi BPi-R64 (sdmmc-2ddr, emmc-2ddr).

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-11 16:24:53 +00:00
Daniel Golle
e2cffbb805
arm-trusted-firmware-mediatek: update to 2021-03-10
Most prominently this adds changes which allow replacing the binary-
only 'bromimage' tool by U-Boot's 'mkimage' (see previous commit).
This fixes build on non-Linux and/or non-x86 platforms.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-11 16:24:48 +00:00
Daniel Golle
ce19e8fa43
tools: mkimage: add patches for 64-bit MediaTek BootROM
Add patches for mkimage to allow using it instead of the binary-only
'bromimage' tool to generate bl2 for MT7622.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-11 16:24:20 +00:00
Daniel Golle
bff84f3e8e arm-trusted-firmware-mediatek: fix typo SPI-SNAND -> SPI-NAND
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-08 21:27:35 +00:00
Daniel Golle
eb030a9a82 arm-trusted-firmware-mediatek: prune now uneeded declarations
Remove unneeded delcarations form package Makefile now that everything
comes from github.com/mtk-openwrt upstream.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-06 03:28:52 +00:00
Daniel Golle
9663562188
arm-trusted-firmware-mediatek: don't select DDR3_FLYBY for 1ddr
DDR3_FLYBY has accidentally been set also for the 1-chip variant which
lead to broken, unbootable images. Fix that.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-05 23:55:56 +00:00
Daniel Golle
51ef823f95
uboot-mediatek: improve BPi-R64 support
* allow MAC address from U-Boot env to be inhertied
 * allow eMMC installation to succeed also without recovery present
   on the SD Card.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-05 20:13:54 +00:00
Daniel Golle
dc416983bb arm-trusted-firmware-mediatek: update to ATF 2.4 (2021-02-25)
All necessary blobs are now contained in the upstream repository, no
more wild replacing of blobs needed.
This new version also contains new storage drivers for (SPI-)NAND which
already comes with support for FM35Q1GA, so that patch can be dropped
as well.
Tested on:
 * Bananapi BPi-R64
   - sdmmc-2ddr
   - emmc-2ddr
 * Linksys E8450
   - snand-1ddr

All works fine (booting Bananapi BPi-R64 from SD Card does NOT require
a signed image, so patch arm-trusted-firmware-mediatek to allow doing
that).

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-05 17:42:10 +00:00
Daniel Golle
f3f630145a
arm-trusted-firmware-mediatek: don't try to install absent files
Don't try to install files which no longer exist
Since {e,sd}mmc are now produced by ptgen they have been removed.

Fixes: 5a3562cd1d ("arm-trusted-firmware-mediatek: remove {e,sd}mmc headers")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-04 21:58:40 +00:00
Daniel Golle
5a3562cd1d arm-trusted-firmware-mediatek: remove {e,sd}mmc headers
Turned out those are simply MBR with active boot partition. And not
needed at all on emmc. Remove them as ptgen can now generate hybrid
MBR sufficient to boot MT7622 from SD Card.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-03 01:00:23 +00:00
Daniel Golle
e3ab355dde uboot-mediatek: bpi-r64: make sure eMMC installation runs only once
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-02 01:42:34 +00:00
Daniel Golle
dba979e2dd uboot-mediatek: bpi-r64: fix eMMC installation menu label
Change boot menu label for eMMC installation to tell what it does now.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-01 20:09:31 +00:00
Daniel Golle
ded54ae196 mediatek: mt7622: bpi-r64: simplify eMMC install procedure
Write everything needed for eMMC install into the gaps between
partitions on SD card. In that way, installation to eMMC only needs
the SD card, no additional files need to be loaded via TFTP any more.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-01 19:33:46 +00:00
Georgi Valkov
3cc57ba462 uboot-sunxi: add missing type __u64
Non Linux systems e.g. macOS lack the __u64 type and produce build errors:
In file included from tools/aisimage.c:9:
In file included from include/image.h:19:
In file included from ./arch/arm/include/asm/byteorder.h:29:
In file included from include/linux/byteorder/little_endian.h:13:
include/linux/types.h:146:9: error: unknown type name '__u64'; did you mean '__s64'?
typedef __u64 __bitwise __le64;

Resolved by declaring __u64 in include/linux/types.h
Build tested on macOS and Ubuntu.

Signed-off-by: Georgi Valkov <gvalkov@abv.bg>
2021-03-01 00:34:23 +01:00
Ronny Kotzschmar
547a932ee9 uboot-envtools: adjust compile patch to version v2021.01
with u-boot v2020.07 some variables have been renamed so this patch needs to be adjusted
otherwise at least with macOS as build system there are build errors

Signed-off-by: Ronny Kotzschmar <ro.ok@me.com>
2021-03-01 00:34:22 +01:00
Daniel Golle
b102e281a4 uboot-envtools: add defaults for Bananapi BPi-R64
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-28 04:12:23 +00:00
Daniel Golle
0246e48434 mt7623n-preloader: remove mt7622-preloader
mt7622-preloader has been superseeded by arm-trusted-firmware-mediatek.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-28 04:12:23 +00:00
Daniel Golle
03948995ab uboot-mediatek: rework support for Bananapi BPi-R64 board
Provide U-Boot variants for SD-card as well as eMMC boot, so we can
generate whole-disk images for the device.
While at it, rename 'mt7622' to 'mt7622-rfb1' to make it less confusing
now that more boards are being added.

Thanks to Frank Wunderlich (@frank-w) for making that nice SVG image
explaining the MMC boot process[1] and for providing the necessary
binary header blobs.

[1]: https://github.com/frank-w/BPI-R64-ATF
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-28 03:40:35 +00:00
Daniel Golle
42f3efec96 uboot-envtools: add defaults for linksys-e8450-ubi
Add U-Boot environment configuration for the Linksys E8450 (UBI) to
allow access to the bootloader environment from OpenWrt via
'fw_printenv' and 'fw_setenv'.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-28 01:23:48 +00:00
Daniel Golle
ed50004319 uboot-mediatek: add support for Linksys E8450
Build U-Boot for the Linksys E8450 in order to have support for UBI.
The loader has a default environment with scripts handling the reset
button as well as fall-back to recovery firmware. If the loader comes
up without a valid environment found in UBI, it will automatically
make sure UBI is formatted and create a new environment and proceed
to load recovery firmware (either from UBI or via TFTP if recovery is
corrupted or unavailable).

If the button is held down during power-on, the yellow status LED
turns on and the bootloader environment is reset to factory defaults.
If the button is released at this point, the recovery firmware (if
existing) is loaded from UBI and booted.
If the button is continously held down even beyond the point that
the yellow LED turned on, the loader will try to load the recovery
firmware via TFTP from server 192.168.1.254, write it to UBI and
boot.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-28 01:23:48 +00:00
Daniel Golle
c16958e194 arm-trusted-firmware-mediatek: add patch for Fidelix SPI NAND
The Linksys E8450 aka. Belkin RT3200 comes with a rather fresh brand
of SPI NAND storage. Add support for it to the nandx driver in
arm-trusted-firmware-mediatek, so we can boot from that chip.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-28 01:23:48 +00:00
Lech Perczak
59d065c9f8 ramips: add support for ZTE MF283+
ZTE MF283+ is a dual-antenna LTE category 4 router, based on Ralink
RT3352 SoC, and built-in ZTE P685M PCIe MiniCard LTE modem.

Hardware highlighs:
- CPU: MIPS24KEc at 400MHz,
- RAM: 64MB DDR2,
- Flash: 16MB SPI,
- Ethernet: 4 10/100M port switch with VLAN support,
- Wireless: Dual-stream 802.11n (RT2860), with two internal antennas,
- WWAN: Built-in ZTE P685M modem, with two internal antennas and two
  switching SMA connectors for external antennas,
- FXS: Single ATA, with two connectors marked PHONE1 and PHONE2,
  internally wired in parallel by 0-Ohm resistors, handled entirely by
  internal WWAN modem.
- USB: internal miniPCIe slot for modem,
  unpopulated USB A connector on PCB.
- SIM slot for the WWAN modem.
- UART connector for the console (unpopulated) at 3.3V,
  pinout: 1: VCC, 2: TXD, 3: RXD, 4: GND,
  settings: 57600-8-N-1.
- LEDs: Power (fixed), WLAN, WWAN (RGB),
  phone (bicolor, controlled by modem), Signal,
  4 link/act LEDs for LAN1-4.
- Buttons: WPS, reset.

Installation:
As the modem is, for most of the time, provided by carriers, there is no
possibility to flash through web interface, only built-in FOTA update
and TFTP recovery are supported.

There are two installation methods:
(1) Using serial console and initramfs-kernel - recommended, as it
allows you to back up original firmware, or
(2) Using TFTP recovery - does not require disassembly.

(1) Using serial console:
To install OpenWrt, one needs to disassemble the
router and flash it via TFTP by using serial console:
- Locate unpopulated 4-pin header on the top of the board, near buttons.
- Connect UART adapter to the connector. Use 3.3V voltage level only,
  omit VCC connection. Pin 1 (VCC) is marked by square pad.
- Put your initramfs-kernel image in TFTP server directory.
- Power-up the device.
- Press "1" to load initramfs image to RAM.
- Enter IP address chosen for the device (defaults to 192.168.0.1).
- Enter TFTP server IP address (defaults to 192.168.0.22).
- Enter image filename as put inside TFTP server - something short,
  like firmware.bin is recommended.
- Hit enter to load the image. U-boot will store above values in
  persistent environment for next installation.
- If you ever might want to return to vendor firmware,
  BACK UP CONTENTS OF YOUR FLASH NOW.
  For this router, commonly used by mobile networks,
  plain vendor images are not officially available.
  To do so, copy contents of each /dev/mtd[0-3], "firmware" - mtd3 being the
  most important, and copy them over network to your PC. But in case
  anything goes wrong, PLEASE do back up ALL OF THEM.
- From under OpenWrt just booted, load the sysupgrade image to tmpfs,
  and execute sysupgrade.

(2) Using TFTP recovery
- Set your host IP to 192.168.0.22 - for example using:
sudo ip addr add 192.168.0.22/24 dev <interface>
- Set up a TFTP server on your machine
- Put the sysupgrade image in TFTP server root named as 'root_uImage'
  (no quotes), for example using tftpd:
  cp openwrt-ramips-rt305x-zte_mf283plus-squashfs-sysupgrade.bin /srv/tftp/root_uImage
- Power on the router holding BOTH Reset and WPS buttons held for around
  5 seconds, until after WWAN and Signal LEDs blink.
- Wait for OpenWrt to start booting up, this should take around a
  minute.

Return to original firmware:
Here, again there are two possibilities are possible, just like for
installation:
(1) Using initramfs-kernel image and serial console
(2) Using TFTP recovery

(1) Using initramfs-kernel image and serial console
- Boot OpenWrt initramfs-kernel image via TFTP the same as for
  installation.
- Copy over the backed up "firmware.bin" image of "mtd3" to /tmp/
- Use "mtd write /tmp/firmware.bin /dev/mtd3", where firmware.bin is
  your backup taken before OpenWrt installation, and /dev/mtd3 is the
  "firmware" partition.

(2) Using TFTP recovery
- Follow the same steps as for installation, but replacing 'root_uImage'
  with firmware backup you took during installation, or by vendor
  firmware obtained elsewhere.

A few quirks of the device, noted from my instance:
- Wired and wireless MAC addresses written in flash are the same,
  despite being in separate locations.
- Power LED is hardwired to 3.3V, so there is no status LED per se, and
  WLAN LED is controlled by WLAN driver, so I had to hijack 3G/4G LED
  for status - original firmware also does this in bootup.
- FXS subsystem and its LED is controlled by the
  modem, so it work independently of OpenWrt.
  Tested to work even before OpenWrt booted.
  I managed to open up modem's shell via ADB,
  and found from its kernel logs, that FXS and its LED is indeed controlled
  by modem.
- While finding LEDs, I had no GPL source drop from ZTE, so I had to probe for
  each and every one of them manually, so this might not be complete -
  it looks like bicolor LED is used for FXS, possibly to support
  dual-ported variant in other device sharing the PCB.
- Flash performance is very low, despite enabling 50MHz clock and fast
  read command, due to using 4k sectors throughout the target. I decided
  to keep it at the moment, to avoid breaking existing devices - I
  identified one potentially affected, should this be limited to under
  4MB of Flash. The difference between sysupgrade durations is whopping
  3min vs 8min, so this is worth pursuing.

In vendor firmware, WWAN LED behaviour is as follows, citing the manual:
- red - no registration,
- green - 3G,
- blue - 4G.
Blinking indicates activity, so netdev trigger mapped from wwan0 to blue:wwan
looks reasonable at the moment, for full replacement, a script similar to
"rssileds" would need to be developed.

Behaviour of "Signal LED" in vendor firmware is as follows:
- Off - no signal,
- Blinking - poor coverage
- Solid - good coverage.

A few more details on the built-in LTE modem:
Modem is not fully supported upstream in Linux - only two CDC ports
(DIAG and one for QMI) probe. I sent patches upstream to add required device
IDs for full support.
The mapping of USB functions is as follows:
- CDC (QCDM) - dedicated to comunicating with proprietary Qualcomm tools.
- CDC (PCUI) - not supported by upstream 'option' driver yet. Patch
  submitted upstream.
- CDC (Modem) - Exactly the same as above
- QMI - A patch is sent upstream to add device ID, with that in place,
  uqmi did connect successfully, once I selected correct PDP context
  type for my SIM (IPv4-only, not default IPv4v6).
- ADB - self-explanatory, one can access the ADB shell with a device ID
  added to 51-android.rules like so:

SUBSYSTEM!="usb", GOTO="android_usb_rules_end"
LABEL="android_usb_rules_begin"
SUBSYSTEM=="usb", ATTR{idVendor}=="19d2", ATTR{idProduct}=="1275", ENV{adb_user}="yes"
ENV{adb_user}=="yes", MODE="0660", GROUP="plugdev", TAG+="uaccess"
LABEL="android_usb_rules_end"

While not really needed in OpenWrt, it might come useful if one decides to
move the modem to their PC to hack it further, insides seem to be pretty
interesting. ADB also works well from within OpenWrt without that. O
course it isn't needed for normal operation, so I left it out of
DEVICE_PACKAGES.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove kmod-usb-ledtrig-usbport, take merged upstream patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-26 13:57:54 +01:00
Daniel Golle
f38c54c635
arm-trusted-firmware-mediatek: correct location of PKG_LICENSE
As PKG_LICENSE is originally set by include/trusted-firmware-a.mk it
can only be appended after that. Hence move that line below the
include to actually make sense.
(cosmetical change, already slipped into openwrt-21.02 branch)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-24 19:01:14 +00:00
Adrian Schmutzler
702147b797 imx-bootlets: refresh patches
Tidy this up a little.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-24 16:15:02 +01:00
Stijn Segers
b5bc53813d uboot-envtools: add support for ZyXEL GS-1900-8HP v1 and v2
This adds the necessary nuts and bolts for the uboot settings for both the ZyXEL GS1900-8HP v1 and v2.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2021-02-23 21:10:56 +01:00
Daniel Golle
9cd089dbbf arm-trusted-firmware-mediatek: use @OPENWRT mirror for blobs
Now that mirrors have picked it up, switch to using the @OPENWRT
mirror instead of hosting those files on Github.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-23 18:03:27 +00:00
Daniel Golle
068c82039f arm-trusted-firmware-mediatek: bring back package
* use binary provided by MediaTek to work-around 'bromimage' issue
 * refactor Makefile
 * add mt7622 1c variants (using binaries provided by MTK)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-23 12:28:49 +00:00
Adrian Schmutzler
910b5d669f tfa-layerscape: build fiptool again
The ls-ddr-phy package needs fiptool options that are not
available via the version from arm-trusted-firmware-tools.
This breaks build for layerscape with the recently added LX2160a:

  create: unrecognized option '--ddr-immem-udimm-1d'

Use the tfa-layerscape variant again for now, but rename it to
fiptool-layerscape to indicate that it's a specific variant.

This reverts 84bc7d31e0 ("tfa-layerscape: don't build fiptool").

Fixes: f59d7aab2a ("layerscape: add ddr-phy package")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-21 00:01:36 +01:00
Yangbo Lu
80dcd14abe layerscape: add LX2160ARDB (Rev2.0 silicon) board support
The QorIQ LX2160A reference design board provides a comprehensive platform
that enables design and evaluation of the LX2160A processor.

- Enables network intelligence with the next generation Datapath (DPPA2)
  which provides differentiated offload and a rich set of IO, including
  10GE, 25GE, 40GE, and PCIe Gen4

- Delivers unprecedented efficiency and new virtualized networks

- Supports designs in 5G packet processing, network function
  virtualization, storage controller, white box switching, network
  interface cards, and mobile edge computing

- Supports all three LX2 family members (16-core LX2160A; 12-core LX2120A;
  and 8-core LX2080A)

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[use AUTORELEASE, add dtb to firmware part]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-19 15:29:46 +01:00
Yangbo Lu
2c2d77bd3b layerscape: add FRWY-LS1046A board support
The LS1046A Freeway board (FRWY) is a high-performance computing,
evaluation, and development platform that supports the QorIQ
LS1046A architecture processor capable of support more than 32,000
CoreMark performance. The FRWY-LS1046A board supports the QorIQ
LS1046A processor, onboard DDR4 memory, multiple Gigabit Ethernet,
USB3.0 and M2_Type_E interfaces for Wi-Fi.

The FRWY-LS1046A-TP includes the Coral Tensor Flow Processing Unit
that offloads AI/ML inferencing from the CPU to provide significant
boost for AI/ML applications. The FRWY-LS1046A-TP includes one M.2
TPU module and more modules can easily be added including USB
versions of the module to scale the AI/ML performance.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[rebase, use AUTORELEASE, fix sorting, add dtb to firmware part]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-19 15:27:15 +01:00
Petr Štetiar
be0192edb8 Revert "uboot-imx6: bump to 2021.01 release"
This reverts commit 50a5a8993d as the bump
to 2021.01 unveiled issue with missing swig host tool needed for
mx6cuboxi's SPL.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2021-02-14 23:28:07 +01:00
Petr Štetiar
50a5a8993d uboot-imx6: bump to 2021.01 release
Refreshed all patches, removed 110-mx6cuboxi-mmc-fallback.patch as it
seems, that upstream has probably added similar funcionality in commit
6c3fbf3e456c ("mx6cuboxi: customize board_boot_order to access eMMC")
and it needs to be re-verified by device owner.

Run tested on apalis.

Cc: Felix Fietkau <nbd@nbd.name>
Cc: Vladimir Vid <vladimir.vid@sartura.hr>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2021-02-14 09:31:30 +01:00
Daniel Golle
dba76a85de arm-trusted-firmware-tools: add patch to pass LDFLAGS
This should hopefully fix builds on the buildbot.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-10 19:19:18 +00:00
Daniel Golle
670bfc86c8 arm-trusted-firmware-mediatek: mark @BROKEN until bromimage gets fixed
The 'bromimage' tool which is used to wrap bl2 with a MediaTek-specific
header is distributed in binary form only and unfortunately tries to
dynamically link against libopenssl, which fails on the buildbots.
Wait for MTK to provide a at least static executable instead, in the
meantime, mark the package as broken.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-10 02:48:57 +00:00
Daniel Golle
ffa0ae17f7
arm-trusted-firmware-tools: fix passing of CFLAGS
HOST_CFLAGS were ignored as they were passed on incorrectly which lead
to build failure if OpenSSL wasn't present on the build host.
Fix that by properly passing HOST_CFLAGS when building each tool.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-10 01:20:58 +00:00
Daniel Golle
ff076f873f
arm-trusted-firmware-tools: remove tools which require libopenssl
They are anyway not used for now, so only build fiptool and sptool.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-09 20:24:58 +00:00
Hauke Mehrtens
98d61b516f uboot-envtools: Update to version 2021.01
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-02-08 22:46:27 +01:00
Paul Spooren
8286f3a3d3 treewide: unify OpenWrt hosted source via @OPENWRT
Multiple sources are hosted on OpenWrts source server only. The source
URLs to point to the server vary based on different epochs in OpenWrts
history.

Replace all by @OPENWRT which is an "empty" mirror, therefore using the
fallback servers sources.cdn.openwrt.org and sources.openwrt.org.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-02-05 12:00:24 -10:00
Daniel Golle
c3959cd54f arm-trusted-firmware-mediatek: make use of trusted-firmware-a.mk
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-03 15:19:14 +00:00
Daniel Golle
84bc7d31e0 tfa-layerscape: don't build fiptool
tfa-fiptool is now provided by an extra package. Use that instead.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-03 15:19:14 +00:00
Daniel Golle
1f1d8d4f47 arm-trusted-firmware-tools: add package
Package ARM Trusted Firmware host tools separately.
(instead of building tfa-fiptool as part of tfa-layerscape)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-03 15:19:14 +00:00
Daniel Golle
a3b55ae510 arm-trusted-firmware-mediatek: add ATF builds for MT7622
ATF bl2 comes in 4 variants for MT7622 depending on the boot media:
 * nor
 * snand
 * emmc
 * sdmmc

Additional binary headers needed for emmc and sdmmc are downloaded as
well and provided along with bl2*.bin and bl31.bin to allow building
images including ATF for MT7622.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-02 18:13:15 +00:00
Marty Jones
1735026632 uboot-rockchip: fix RockPro64 boot from eMMC
With upstream commit f81f9f0ebac5 ("rockchip: rockpro64: initialize USB in
preboot") CONFIG_USE_PREBOOT was enabled on the RockPro64, which is causing
boot issues when a eMMC is used, as a workaround will temporarily disable
this option.

Signed-off-by: Marty Jones <mj8263788@gmail.com>
[Improve patch description]
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-01 00:48:06 +01:00
Andre Heider
a04bffebba arm-trusted-firmware-mvebu: pass commit ids to a3700-utils/mv-ddr-marvell
The two required tools fail to identify their version when not compiling
from a git clone, patch that in and pass on the used commit hashes.

Upon boot it now prints "WTMI-devel-18.12.1-5598e150".

Signed-off-by: Andre Heider <a.heider@gmail.com>
2021-01-30 14:46:32 +01:00
Andre Heider
5fae94d987 arm-trusted-firmware-mvebu: bump espressobin boards to CPU_1000_DDR_800
The cpufreq issue has been identified and a fix is in the process of beeing
upstreamed [0].

Bump the boards to the default 1000MHz so they can run at that frequency
once the fix is merged. Until then the boards are stuck at 800MHz (just
claiming to run 1000Hz, which is a lie).

[0] https://lore.kernel.org/linux-arm-kernel/20210114124032.12765-1-pali@kernel.org/

Signed-off-by: Andre Heider <a.heider@gmail.com>
2021-01-30 14:46:32 +01:00
Andre Heider
8f3bd881c9 arm-trusted-firmware-mvebu: update to v2.4
Signed-off-by: Andre Heider <a.heider@gmail.com>
2021-01-30 14:46:32 +01:00
Andre Heider
a9c20d56f1 uboot-mvebu: update to v2021.01
u-boot now detects emmc variants at runtime, we don't need to build
seperate binaries anymore.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2021-01-30 14:46:32 +01:00
Andre Heider
00bf2c0cbe arm-trusted-firmware-mvebu: don't build emmc variants
Starting with u-boot v2021.01 a single binary will be used for non-emmc
and emmc variants.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2021-01-30 14:46:32 +01:00
Jiang Yongquan
799fca7602 sunxi: add support for linksprite pcDuino3 nano board
Specifications:

 - SoC: Allwinner A20 @ 1Ghz
 - DRAM: 1GiB DDR3 @ 408MHz (K4B4G1646Q-HYK0)
 - NAND: 4GB MLC NAND (H27UBG8T2BTR-BC)
 - Ethernet: 10/100/1000Mbps Ethernet (Realtek RTL8211E)

Flash instructions:

dd if=openwrt-sunxi-cortexa7-linksprite_pcduino3-nano-ext4-sdcard.img
of=/dev/sdX

Signed-off-by: Jiang Yongquan <woxwchc@foxmail.com>
[Remove CONFIG_REALTEK_PHY from sunxi/cortexa53 config]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-01-27 23:14:30 +01:00
Michael Pratt
96017a6013 ath79: add support for Senao Engenius EAP1200H
FCC ID: A8J-EAP1200H

Engenius EAP1200H is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+

**Specification:**

  - QCA9557 SOC
  - QCA9882 WLAN	PCI card, 5 GHz, 2x2, 26dBm
  - AR8035-A PHY	RGMII GbE with PoE+ IN
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 2x 64 MB RAM	NT5TU32M16FG
  - UART at J10		populated
  - 4 internal antenna plates (5 dbi, omni-directional)
  - 5 LEDs, 1 button (power, eth0, 2G, 5G, WPS) (reset)

**MAC addresses:**

  MAC addresses are labeled as ETH, 2.4G, and 5GHz
  Only one Vendor MAC address in flash

  eth0 ETH  *:a2 art 0x0
  phy1 2.4G *:a3 ---
  phy0 5GHz *:a4 ---

**Serial Access:**

  the RX line on the board for UART is shorted to ground by resistor R176
  therefore it must be removed to use the console
  but it is not necessary to remove to view boot log

  optionally, R175 can be replaced with a solder bridge short

  the resistors R175 and R176 are next to the UART RX pin at J10

**Installation:**

  2 ways to flash factory.bin from OEM:

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.1.1
    username and password "admin"
    Navigate to "Firmware Upgrade" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt uboot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9fd70000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

**Return to OEM:**

  If you have a serial cable, see Serial Failsafe instructions
  otherwise, uboot-env can be used to make uboot load the failsafe image

  *DISCLAIMER*
  The Failsafe image is unique to Engenius boards.
  If the failsafe image is missing or damaged this will brick the device
  DO NOT downgrade to ar71xx this way, it can cause kernel loop or halt

  ssh into openwrt and run
  `fw_setenv rootfs_checksum 0`
  reboot, wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

**TFTP recovery:**

  Requires serial console, reset button does nothing

  rename initramfs to 'vmlinux-art-ramdisk'
  make available on TFTP server at 192.168.1.101
  power board, interrupt boot
  execute tftpboot and bootm 0x81000000

  NOTE: TFTP is not reliable due to bugged bootloader
  set MTU to 600 and try many times

**Format of OEM firmware image:**

  The OEM software of EAP1200H is a heavily modified version
  of Openwrt Kamikaze. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-ar71xx-generic-eap1200h-uImage-lzma.bin
    openwrt-ar71xx-generic-eap1200h-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring.

  Newer EnGenius software requires more checks but their script
  includes a way to skip them, otherwise the tar must include
  a text file with the version and md5sums in a deprecated format.

  The OEM upgrade script is at /etc/fwupgrade.sh.

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

Note on PLL-data cells:

  The default PLL register values will not work
  because of the external AR8035 switch between
  the SOC and the ethernet port.

  For QCA955x series, the PLL registers for eth0 and eth1
  can be see in the DTSI as 0x28 and 0x48 respectively.
  Therefore the PLL registers can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x18050028 1` and `md 0x18050048 1`.

  The clock delay required for RGMII can be applied
  at the PHY side, using the at803x driver `phy-mode`.
  Therefore the PLL registers for GMAC0
  do not need the bits for delay on the MAC side.
  This is possible due to fixes in at803x driver
  since Linux 5.1 and 5.3

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2021-01-23 12:53:22 +01:00
Paul Spooren
465eaa0e07 uboot-envtools: use $(AUTORELEASE) for PKG_RELEASE
Use `$(AUTORELEASE)` variable rather than setting a PKG_RELEASE
on every commit manually.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-01-22 19:03:53 -10:00
Dmytro Oz
c2a7bb520a ramips: mt7621: add support for Xiaomi Mi Router 4
Xiaomi Mi Router 4 is the same as Xiaomi Mi Router 3G, except for
the RAM (256Mib→128Mib), LEDs and gpio (MiNet button).

Specifications:

Power: 12 VDC, 1 A
Connector type: barrel
CPU1: MediaTek MT7621A (880 MHz, 4 cores)
FLA1: 128 MiB (ESMT F59L1G81MA)
RAM1: 128 MiB (ESMT M15T1G1664A)
WI1 chip1: MediaTek MT7603EN
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: U.FL
WI2 chip1: MediaTek MT7612EN
WI2 802dot11 protocols: an+ac
WI2 MIMO config: 2x2:2
WI2 antenna connector: U.FL
ETH chip1: MediaTek MT7621A
Switch: MediaTek MT7621A

UART Serial
[o] TX
[o] GND
[o] RX
[ ] VCC - Do not connect it

MAC addresses as verified by OEM firmware:

use   address   source
LAN   *:c2      factory 0xe000 (label)
WAN   *:c3      factory 0xe006
2g    *:c4      factory 0x0000
5g    *:c5      factory 0x8000

Flashing instructions:

1.Create a simple http server (nginx etc)
2.set uart enable
To enable writing to the console, you must reset to factory settings
Then you see uboot boot, press the keyboard 4 button (enter uboot command line)
If it is not successful, repeat the above operation of restoring the factory settings.
After entering the uboot command line, type:

setenv uart_en 1
saveenv
boot

3.use shell in uart
cd /tmp
wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin
wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin
mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin kernel1
mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin rootfs0
nvram set flag_try_sys1_failed=1
nvram commit
reboot
4.login to the router http://192.168.1.1/

Installation via Software exploit
Find the instructions in the https://github.com/acecilia/OpenWRTInvasion

Signed-off-by: Dmytro Oz <sequentiality@gmail.com>
[commit message facelift, rebase onto shared DTSI/common device
definition, bump uboot-envtools]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-21 22:53:19 +01:00
Sven Eckelmann
0988e03f0e ath79: Add support for OpenMesh MR1750 v2
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
  - AR8035 ethernet PHY (RGMII)
  - 10/100/1000 Mbps Ethernet
  - 802.3af POE
  - used as LAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-19 21:41:26 +01:00
Sven Eckelmann
ae7680dc4b ath79: Add support for OpenMesh MR1750 v1
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
  - AR8035 ethernet PHY (RGMII)
  - 10/100/1000 Mbps Ethernet
  - 802.3af POE
  - used as LAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, apply shared DTSI/device node, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-19 21:41:26 +01:00
Sven Eckelmann
31172e53f9 ath79: Add support for OpenMesh MR900 v2
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi
* 3T3R 5 GHz Wi-Fi
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
  - AR8035 ethernet PHY (RGMII)
  - 10/100/1000 Mbps Ethernet
  - 802.3af POE
  - used as LAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-19 15:39:36 +01:00
Sven Eckelmann
e06c9eec5d ath79: Add support for OpenMesh MR900 v1
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi
* 3T3R 5 GHz Wi-Fi
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
  - AR8035 ethernet PHY (RGMII)
  - 10/100/1000 Mbps Ethernet
  - 802.3af POE
  - used as LAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-19 15:39:36 +01:00