Add driver for NVM Express block devices, ie. PCIe connected SSDs.
Targets which allow booting from NVMe (x86, maybe some mvebu boards come
to mind) should have it built-in, so rootfs can be mounted from there.
For targets without NVMe support in bootloader or BIOS/firmware it's
sufficient to provide the kernel module package.
On targets having the NVMe driver built-in the resulting kmod package
is an empty dummy. In any case, depending on or installing kmod-nvme
results in driver support being available (either because it was already
built-in or because the relevant kernel modules are added and loaded).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Accessing the console on many devices is difficult.
netconsole eases debugging on devices that crash
after the network is up.
Reference to the netconsole documentation in upstream Linux:
<https://www.kernel.org/doc/html/latest/networking/netconsole.html>
|
|netconsole=[+][src-port]@[src-ip]/[<dev>],[tgt-port]@<tgt-ip>/[tgt-macaddr]
|
| where
| + if present, enable extended console support
| src-port source for UDP packets (defaults to 6665)
| src-ip source IP to use (interface address)
| dev network interface (eth0)
| tgt-port port for logging agent (6666)
| tgt-ip IP address for logging agent
| tgt-macaddr ethernet MAC address for logging agent (broadcast)
OpenWrt specific notes:
OpenWrt's device userspace scripts are attaching the network
interface (i.e. eth0) to a (virtual) bridge (br-lan) device.
This will cause netconsole to report:
|network logging stopped on interface eth0 as it is joining a master device
(and unfortunately the traffic/logs to stop at this point)
As a workaround, the netconsole module can be manually loaded
again after the bridge has been setup with:
insmod netconsole netconsole=@/br-lan,@192.168.1.x/MA:C...
One way of catching errors before the handoff, try to
append the /etc/modules.conf file with the following extra line:
options netconsole netconsole=@/eth0,@192.168.1.x/MA:C...
and install the kmod-netconsole (=y) into the base image.
Signed-off-by: Catalin Toda <catalinii@yahoo.com>
(Added commit message from PR, added links to documentation)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
the legacy driver was dropped in linux 5.14-rc3:
commit d249ff28b1d8 ("intersil: remove obsolete prism54 wireless driver")
Quoting Lukas Bulwahn:
"p54 replaces prism54 so users should be unaffected."
Reported-by: Marius Dinu <m95d+git@psihoexpert.ro>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
TechNexion PICO-PI-IMX7D uses BCM4339 Wi-Fi interface in SDIO mode.
Enable SDIO support for imx/cortexa7 to fully support it in images.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Add package supporting Bluetooth HCI interfaces connected over SDIO.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[pepe2k@gmail.com: dropped rfkill dependency, other minor text fixes]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Backport upstream fix to build on kernel 5.15.52 or later since kernel
devs backported newer functionality to older kernels.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The mac80211-hwsim and the Intel iwlwifi driver support ieee80211ax, add
the missing DRIVER_11AX_SUPPORT dependency too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
c07f45927839 firmware: update mt7622 firmware to version 20220630
af406a2d1c36 mt76: do not use skb_set_queue_mapping for internal purposes
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This external switch driver should be loaded on boot for network
support in failsafe mode.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
This external switch driver should be loaded on boot for network
support in failsafe mode.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
In Turris MOX SDIO card [1], which uses Marvell 88W997 and its driver
mwifiex, you might get cryptic messages, which are not helpful to use.
@pali created patch, which improves messages by the driver and he will
send this to Linux kernel soon.
Before:
[ 81.026156] mwifiex_sdio mmc1:0001:1: CMD_RESP: cmd 0x20 error, result=0x1
After:
[ 15.784018] mwifiex_sdio mmc1:0001:1: CMD_RESP: cmd RF_ANTENNA (0x20) error, result=0x1
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
SDIO chip 88W9997 from NXP [1] is quite limited by its firmware and
driver. Add hacky patch to allow up to 4 SSID instead of 3 SSID.
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Introduce a new option background_radar to toggle hostapd's background
radar feature. Enabling this allows DFS CAC to run on dedicated radio RF
chains while the radio(s) are otherwise running normal AP activities on
other channels.
As OpenWrt configures hostapd to use a channel list even when a single
channel is configured, using this feature requires a list of channels in
/etc/config/wireless. Alternatively, channel can be set to auto.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Enable ath10k offload by default. This improves wireless performance
without requiring user configuration.
This adds ath10k_core to the AUTOLOAD section so that the frame_mode
paramter can be added to /etc/modules.d and passed to the driver.
The frame_mode 2 enables ethernet mode on the firmware/driver.
This parameter is set by passing a different value to the frame_mode
value on kmod insmod.
Link to the original patchset:
https://patchwork.kernel.org/project/linux-wireless/cover/20220516032519.29831-1-ryazanov.s.a@gmail.com/
Signed-off-by: Tiago Gaspar <tiagogaspar8@gmail.com>
This reverts the airtime scheduler back from the virtual-time based scheduler
to the deficit round robin scheduler implementation.
This reduces burstiness and improves fairness by improving interaction with AQL.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
1696f9eb8b40 mt76: mt7915: do not copy ieee80211_ops pointer in mt7915_mmio_probe
a4db5869d660 mt76: mt7915: update mpdu density in 6g capability
500c18014d95 mt76: mt7915: add sta_rec with EXTRA_INFO_NEW for the first time only
3ef66fc7c714 mt76: do not check the ccmp pn for ONLY_MONITOR frame
dd682eead016 mt76: mt7915: update the maximum size of beacon offload
4fb991f2c997 mt76: mt7615: add sta_rec with EXTRA_INFO_NEW for the first time only
ba39ed3b44f1 mt76: mt76x02: improve reliability of the beacon hang check
fd8211cf7c59 mt76: mt7921: sync with updated patch
f2edd340ddb4 mt76: allow receiving frames with invalid CCMP PN via monitor interfaces
b6e865e2cc70 mt76: mt7615: fix throughput regression on DFS channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The MAC can be stored in OTP memory or in flash memory, currently the
driver could read it only from OTP. Backport the patch allowing setting
the MAC address from flash. Some modules have the OTP programmed but
the ODM/OEM decided to overwrite it with value stored in flash.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
These narrowments are no longer useful, since there's no lower version
than 5.10 supported in tree.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
4554ee652caf mt76: mt7921: fix warning Using plain integer as NULL pointer
a3f1d6ccf3ca mt76: mt7921: add missing bh-disable around rx napi schedule
9aeca2a5ce47 mt76: mt7921: get rid of mt7921_mcu_exit
fee8a5911c76 mt76: connac: move shared fw structures in connac module
db4d784ae7ba mt76: mt7921: move fw toggle in mt7921_load_firmware
16ab6bf49556 mt76: connac: move mt76_connac2_load_ram in connac module
29fd748801c6 mt76: connac: move mt76_connac2_load_patch in connac module
051c68d18214 mt76: mt7663: rely on mt76_connac2_fw_trailer
d6ae3505ac6c mt76: enable the VHT extended NSS BW feature
488a5ccc9762 mt76: mt7921: rely on mt76_dev in mt7921_mac_write_txwi signature
934029bb93e2 mt76: mt7915: rely on mt76_dev in mt7915_mac_write_txwi signature
ecefae4c7d72 mt76: connac: move mac connac2 defs in mt76_connac2_mac.h
b5eecc841df8 mt76: connac: move connac2_mac_write_txwi in mt76_connac module
012e619a07b9 mt76: connac: move mt76_connac2_mac_add_txs_skb in connac module
1b492be795ea mt76: mt7921: not support beacon offload disable command
f1f46d3b4b19 mt76: mt7921: fix command timeout in AP stop period
cae61112ef1d mt76: connac: move HE radiotap parsing in connac module
487674062643 mt76: connac: move mt76_connac2_reverse_frag0_hdr_trans in mt76-connac module
649bdc4983c4 mt76: connac: move mt76_connac2_mac_fill_rx_rate in connac module
cb75aaa39252 mt76: mt7921s: remove unnecessary goto in mt7921s_mcu_drv_pmctrl
e0eaf66eaebb mt76: mt7615: do not update pm stats in case of error
f8d125b4ea30 mt76: mt7921: do not update pm states in case of error
6329a834907e mt76: mt7921s: fix possible sdio deadlock in command fail
8a04f1b04662 mt76: mt7921: fix aggregation subframes setting to HE max
e52283439094 mt76: mt7915: disable UL MU-MIMO for mt7915
fd3958970e3d mt76: mt7921: enlarge maximum VHT MPDU length to 11454
18df38fe77f7 mt76: mt7915: get rid of unnecessary new line in mt7915_mac_write_txwi
149e95f5d7a6 mt76: connac: move mt76_connac_fw_txp in common module
899d192e8a79 mt76: move mt7615_txp_ptr in mt76_connac module
7184f0a6f6a5 mt76: connac: move mt76_connac_tx_free in shared code
c42d45278fa5 mt76: connac: move mt76_connac_tx_complete_skb in shared code
0993f4ef96f8 mt76: connac: move mt76_connac_write_hw_txp in shared code
467960fab791 mt76: connac: move mt7615_txp_skb_unmap in common code
2e758064b085 mt76: mt7915: rely on mt76_connac_tx_free
2065a7901671 mt76: move mcu_txd/mcu_rxd structures in shared code
576c1b7c472b mt76: move mt76_connac2_mcu_fill_message in mt76_connac module
7275f7758090 mt76: mt7915: fix incorrect testmode ipg on band 1 caused by wmm_idx
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This adds a few fixes for compiling against Linux 5.10:
1. segment_eq() has been removed with upstream commit
428e2976a5bf7e7f5554286d7a5a33b8147b106a ("uaccess: remove
segment_eq") and can use uaccess_kernel() instead
2. ioremap_nocache() is removed and is now an alias for ioremap() with
upstream commit 4bdc0d676a643140bdf17dbf7eafedee3d496a3c ("remove
ioremap_nocache and devm_ioremap_nocache")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This backports encap offload support from upstream.
On some ath10k devices there can be about 10% improvement on tx throughput.
Users can turn it on by setting frame_mode=2.
Signed-off-by: Zhijun You <hujy652@gmail.com>
This patch adds support for the mainline kernel module for the PCA955x
LED driver. Note this requires i2c and GPIO support. Also worth calling
out this driver also enables GPIO support, depending on device tree
configuration.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Sync nl80211.h with upstream in order to maintain parity with
nl80211_copy.h shipped with hostapd.
This is necessary, as currently the enum value for
NL80211_EXT_FEATURE_RADAR_BACKGROUND mismatches between hostapd and
mac80211. This breaks background radar capability detection in hostapd.
Reported-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David Bauer <mail@david-bauer.net>
In case no specific BSS color is configured, set it to a random value.
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Delete the crypto-lib-blake2s kmod package, as BLAKE2s is now built-in.
Patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800, x86/64
Signed-off-by: John Audia <therealgraysky@proton.me>
Major changes are:
Add support for smbd-direct multi-desctriptor.
Add support for dkms.
Add support for key exchange.
Fix seveal bugs.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Make ar8216/8327 swconfig driver modularizable and add
entry to the netdevices.mk kernel modules file.
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
latency and short-term fairness is improved by fixing the tx queue sorting
so that it considers the pending AQL budget
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Needed by strongSwan IPsec VPN for strongswan-mod-chapoly. Not to be confused with
kmod-crypto-LIB-chacha20poly1305, which is an 8-byte nonce version used
by wireguard.
Signed-off-by: Xu Wang <xwang1498@gmx.com>
Add ieee80211_rx_check_bss_color_collision routine in order to introduce
BSS color collision detection in mac80211 if it is not supported in HW/FW
(e.g. for mt7915 chipset).
Add IEEE80211_HW_DETECTS_COLOR_COLLISION flag to let the driver notify
BSS color collision detection is supported in HW/FW. Set this for ath11k
which apparently didn't need this code.
Tested-by: Peter Chiu <Chui-Hao.Chiu@mediatek.com>
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/a05eeeb1841a84560dc5aaec77894fcb69a54f27.1648204871.git.lorenzo@kernel.org
[clarify commit message a bit, move flag to mac80211]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Original patch: https://github.com/cifsd-team/ksmbd-tools/issues/227
adapted for ksmbd kernel module v3.4.3 by me.
Fixes crash in v3.4.3 only. Use original patch when updating to v3.4.4
as this one will fail hunk #1.
Signed-off-by: Marius Dinu <m95d+git@psihoexpert.ro>
Some ath10k IPQ40xx devices like the MikroTik hAP ac2 and ac3 require the
BDF-s to be extracted from the device storage instead of shipping packaged
API 2 BDF-s.
This is required as MikroTik has started shipping boards that require BDF-s
to be updated, as otherwise their WLAN performance really suffers.
This is however impossible as the devices that require this are release under
the same revision and its not possible to differentiate them from devices
using the older BDF-s.
In OpenWrt we are extracting the calibration data during runtime and we are
able to extract the BDF-s in the same manner, however we cannot package the
BDF-s to API 2 format on the fly and can only use API 1 to provide BDF-s on
the fly.
This is an issue as the ath10k driver explicitly looks only for the board.bin
file and not for something like board-bus-device.bin like it does for pre-cal
data.
Due to this we have no way of providing correct BDF-s on the fly, so lets
extend the ath10k driver to first look for BDF-s in the board-bus-device.bin
format, for example: board-ahb-a800000.wifi.bin
If that fails, look for the default board file name as defined previously.
So, backport the upstream ath10k patch.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update ath10k-ct to the latest version which includes the backported
ath10k commit for requesting API 1 BDF-s with a unique name like caldata.
Signed-off-by: Robert Marko <robimarko@gmail.com>
HOST_LOADLIBES was renamed to KBUILD_HOSTLDLIBS in kernel 4.19. As the
oldest kernel version we support is 5.10, cleanup HOST_LOADLIBES use.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
