Flash procedure is described in next commit.
TLDR:
Copy preloader and uboot to /tmp and write them in the mtd.
This will also require new UBI partition and
volumes to boot openwrt.
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-preloader.bin bl2
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-bl31-uboot.fip fip
Changelist:
- Added profile for 4k+256 SPI NAND_TYPE
- Added basic Zyxel EX5601-T0 uboot profile
Backported from hitech95 branch:
- Button RESET pin fix
- Button WPS pin fix
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
(cherry picked from commit a9cf87027e)
The vendor uboot will verify firmware at boot.
So add a custom uboot build for this device.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit b42c527228)
The OEM U-Boot uses dual boot and signature verification which does not
support by OpenWrt. So add a custom U-Boot build for OpenWrt.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit fddd735dd5)
With patch 101-03-spi-mtk_spim-get-spi-clk-rate-only-once.patch
a new system to calculate the SPI clocks has been added.
Unfortunately, the do_div macro overrides the global
priv->pll_clk_rate field. This will cause to have a reduced
clock rate on each subsequent SPI call.
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
(cherry picked from commit 8849ccb995)
It must read the entire image for previous code of 'imsz' or 'imszb'.
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
Suggested-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit 3bbc1d5fba)
Improve and package builds for various boot media configurations of the
MediaTek MT7981 reference board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 8428bed15d)
Commit 572ea68070 ("uboot-mediatek: add patches for MT7988 and
builds for RFB") renamed HSGMII to 2500basex, but forgot to update
the dts of Redmi Router AX6000, makes the network unusable.
This patch makes the network usable again.
Fixes: #13724
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Furong Xu <xfr@outlook.com>
(cherry picked from commit 03987d2d11)
Sync SPI-NAND/ECC controller driver for MT7622, MT7981, MT7986 and MT7988:
* Platform data for MT7981 was actually missing and is now added.
* Add support for Winbond W25N01KV 1Gbit chip.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 9725524235)
The U-Boot build for the MT7988 reference board booting from SD card
wrongly depended on the 'ddr4' variant of the ARM TrustedFirmware-A build
even though the 'comb' variant is used. Fix that dependency.
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 78e3adcaf9)
While the v2 is nearly identical to v1, v3 uses a different PHY and
needs a different build for Ethernet to work in U-Boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit fff4441135)
Select many potentially useful options for the MT7988 RFB U-Boot builds.
The resulting loader is intended as a development tool and intends to be
generic. It does *not* have a default bootcmd set, but allows to boot
pretty much everything, including EFI executables.
To install this U-Boot build to the eMMC:
opkg install mmc-utils partx-utils
mmc bootpart enable 1 1 /dev/mmcblk0
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=*mediatek_mt7988a-rfb-nand-emmc-preloader.bin of=/dev/mmcblk0boot0
dd if=*mediatek_mt7988a-rfb-nand-emmc-gpt.bin of=/dev/mmcblk0
partx -a /dev/mmcblk0
dd if=*mediatek_mt7988a-rfb-nand-emmc-bl31-uboot.fip of=/dev/mmcblk0p3
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 1d5778e18d)
Instead of reading only a single 4kiB page, read the first 128kiB to
determine the size of an uImage.FIT using 'imsz' or 'imszb'.
This will be needed once we add more Device Tree Overlays, which may
happen for the BPi-R3 mini.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 3c2f7bb555)
Add patch to fix build failure caused by a missing header which had
previously been implicitely included.
Fixes: 6ddb5f5a65 ("uboot-mediatek: update to version 2023.07.02")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Among the patches adding support for MT7988 also came the switch to
use fdtdec_setup_mem_size_base() and no longer rely on CFG_SYS_SDRAM_BASE.
Take care of our downstream boards which did not have a 'memory' node in
their device trees.
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import pending patches adding support for MT7988 and provide builds
for the reference board for all possible boot media.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Release 2023.07 got tagged wrongly and replaced by follow-up release
2023.07.02.
Now using upstream DTS for BPi-R3.
Removed two patches which made it upstream, refreshed the rest.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The side-effect and main motivation is to also drop the FIT structure size
limit because with multiple device tree overlays it may easily grow beyond
the previous 4kB limit in the future.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 98e3f82c3f)
The OEM uboot limit brush into 3rd-party firmware.
So add a custom uboot build to support openwrt.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 437e79ad6d)
Update bootloader environment for BPi-R3 and BPi-R64 to adapt to new
device tree overlay mechanism now that support for multiple device
tree overlays has been added.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit ec50d2d366)
The vendor uboot will verify firmware at boot.
So add a custom uboot build for this device.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit c51eb17730)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add reserved memory for pstore/ramoops to device tree used by Linux
as well as U-Boot.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 3eb354f999)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The image_header_t typedef has been removed from
uboot v2023.01 [1], replaced with legacy struct.
[1] f3543e6944
Fixes: 3d5c542 ("uboot-mediatek: update to U-Boot 2023.01")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
CONFIG_SYS_TEXT_BASE has been renamed to CONFIG_TEXT_BASE
in uboot v2023.01 [1], fixes all this variable.
[1] 984639039f
Fixes: 3d5c5427 ("uboot-mediatek: update to U-Boot 2023.01")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
TP-Link TL-XDR608x comes with locked vendor loader. Add U-Boot build
for replacement loader for both TL-XDR6086 and TL-XDR6088. The only
difference at U-Boot level is the different filename requested via
TFTP, matching the corresponding OpenWrt build artifacts for each
device.
The TP-Link TL-XDR4288 has the same hardware as the TP-Link TL-XDR6088
except for the wireless part. Also create a uboot for the TP-Link
TL-XDR4288.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[rebase to uboot 23.04, correct led and button]
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
U-Boot commit ea6fdc13595 ("dm: button: add support for linux_code in
button-gpio.c driver") makes it mandatory to specify linux,code for all
buttons. As that broke handling of the reset button in U-Boot with the
update to U-Boot 2023.04, add linux,code for all butons.
Reported-by: @DragonBluep
Fixes: 50f7c5af4a ("uboot-mediatek: update to v2023.04")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Updating to U-Boot 2023.04 broke the build for the RAVPower RP-WD009
MT7628 board. This was due to upstream conversion of CONFIG_* to CFG_*
which was not applied to our downstream patch adding support for the
RAVPower RP-WD009 device.
Apply CONFIG_* to CFG_* converion analog to what has been done also
for mt7928_rfb upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update to next U-Boot timed release.
Remove now obsolete patch
100-01-board-mediatek-add-more-network-configurations.patch
Default IP addresses are now dealt with in Kconfig, no longer in board-
specific C header files.
Add patches to restore ANSI support in bootmenu which was broken upstream,
always use high-speed mode on serial UART for improved stability and fix
an issue with pinconf not being applied on MT7623 resulting in eMMC
being inaccessible when booting from micro SD card.
In order to keep the size of the bootloader on MT7623 below 512kB remove
some unneeded commands on both MT7623 boards.
Tested on:
* BananaPi BPi-R2 (MT7623N)
* BananaPi BPi-R3 (MT7986A)
* BananaPi BPi-R64 (MT7622A)
* Linksys E8450 (MT7622B)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
They are enabled by selecting devices. Fixes build errors when enabling extra
devices without creating a new config from scratch.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move defines from header to defconfig
The package build and the Buildbot hang in 'make syncconfig' for
u-boot-ravpower_rp-wd009 because CONFIG_SYS_MIPS_TIMER_FREQ is not in
the .config, causing a console prompt. Also moved two other defines in
defconfig causing duplicate definition warnings.
Fixes: 3d5c5427e1 ("uboot-mediatek: update to U-Boot 2023.01")
Signed-off-by: Jo Deisenhofer <jo.deisenhofer@gmail.com>
Support for MT7981 and MT7986 has been merged, remove patches.
Tested on a couple of MT7986, MT7622 and MT7623 boards.
MIPS builds are untested.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
U-Boot flash instructions:
0. OpenWrt U-Boot does not support stock layout, it comes with recovery
boot support, automatic tftp recovery and never blocks UART.
A new flash layout is introduced, we call it OpenWrt U-Boot layout,
stock flash layout and the old OpenWrt layout are not supported.
During the whole flash procedure, please do not reboot or power off
unless requested explicitly, or you will break your device.
1. Your device should already running OpenWrt.
If not, follow the instructions to flash OpenWrt:
https://github.com/openwrt/openwrt/pull/11115
2. Backup BL2 Nvram Bdata Factory and FIP in case you break something or
in case you want to go back to stock firmware one day.
cat /dev/mtdblock0 > /tmp/BL2.bin
cat /dev/mtdblock1 > /tmp/Nvram.bin
cat /dev/mtdblock2 > /tmp/Bdata.bin
cat /dev/mtdblock3 > /tmp/Factory.bin
cat /dev/mtdblock4 > /tmp/FIP.bin
And save all whose bin files to somewhere safe.
Then backup your configurations, since ubiformat for entire mtd device is
required to create new ubootenv volume for OpenWrt U-Boot.
3. Run the following cmd to boot into an initramfs with the new OpenWrt
U-Boot layout that expand ubi partion to the end of flash:
ubiformat /dev/mtd7 -y -f /tmp/ax6000-ubootmod-initramfs-factory.ubi
4. After boot into initramfs, check mtd partion info.
The ubi partion should be mtd5
root@OpenWrt:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00100000 00020000 BL2
mtd1: 00040000 00020000 Nvram
mtd2: 00040000 00020000 Bdata
mtd3: 00200000 00020000 Factory
mtd4: 00200000 00020000 FIP
mtd5: 07a80000 00020000 ubi
5. Load kmod-mtd-rw to temporarily make the bootloader partions writable.
The kmod-mtd-rw is from the feeds, it is not packed in initramfs-factory
by default.
To install kmod-mtd-rw via opkg:
opkg update && opkg install kmod-mtd-rw
Or, download kmod-mtd-rw.ipk from OpenWrt server and install it manually
e.g:
https://downloads.openwrt.org/snapshots/targets/mediatek/filogic/kmods/
Select your OpenWrt release version and kernel version accordingly.
Load kmod-mtd-rw:
insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1
6. Run the following cmd to clean all pending crash dumps in pstore,
or OpenWrt U-Boot may boot into NAND recovery or tftp recovery.
rm -f /sys/fs/pstore/*
7. Format ubi and create new ubootenv volume:
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
8. This is optional. Skip this if you do not want to have NAND recovery
boot feature offered by OpenWrt U-Boot. Don't worry, you always have
automatic tftp recovery feature enabled.
ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
ubiupdatevol /dev/ubi0_2 /tmp/ax6000-ubootmod-initramfs-recovery.itb
9. Now, flash new U-Boot. Bye-bye ugly stock U-Boot.
mtd write /tmp/ax6000-ubootmod-preloader.bin BL2
mtd write /tmp/ax6000-ubootmod-bl31-uboot.fip FIP
10. Flash the squashfs-sysupgrade.bin as usual:
sysupgrade -n /tmp/ax6000-ubootmod-squashfs-sysupgrade.itb
Enjoy!
Signed-off-by: Furong Xu <xfr@outlook.com>
Raise CONFIG_LMB_MAX_REGIONS to 64 as there are going to be more than
8 (the default value) reserved regions to allow supporting offloading
Wireless-to-Ethernet traffic on MT7986.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix mmc_write_vol hush script used by many boards to avoid timeouts on
slow SD cards:
Instead of erasing a complete partition, only erase blocks for the
to-be-written image when writing to MMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove patches adding support for MT7621 which have been merged upsteam.
Patches for MT7981 and MT7986 have been merged too, but not in time to
be included in the 2022.10 release, so we have to keep carrying them
until the 2023.01 release.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
CONFIG_CMD_MTDPART does not exist, fix it.
Fixes: e9ad412 ("uboot-mediatek: add build for Ubiquiti Networks UniFi 6 LR")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
CONFIG_CMD_MTDPART does not exist, fix it.
Fixes: ed50004 ("uboot-mediatek: add support for Linksys E8450")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The GPIO used for the RST button is also used for PCIe-CLKREQ signal.
Hence it cannot be used as button signal if PCIe is also used.
Wire up WPS button to serve as KEY_RESTART in Linux and "reset" button
in U-Boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Weijie Gao has submitted an updated version of the patchset adding
support for MT7986 and MT7981 to U-Boot. Use that v2 patchset.
Changes of v2:
- Add cpu driver for print_cpuinfo()
- Fix NULL pointer dereference in mtk_image
(was already fixed in OpenWrt)
- Fix coding style
- Minor changes
https://patchwork.ozlabs.org/project/uboot/list/?series=316148
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Bananapi BPi-R3 board can boot from eMMC, SD card, SPI-NAND and
SPI-NOR, depending on the position of switches controlling the BOOTSEL
bootstrap pins as we as hard-wired chip-select lines. The position of the
chip-select switch SW6 decides whether either SD card or eMMC can be
accessed, SW5 selects either SPI-NAND or SPI-NOR.
Generate U-Boot for all 4 boot options. The SD card version allows
installation to SPI-NAND and SPI-NOR (eMMC cannot be accessed
simultanously with the SD card), the SPI-NAND version allows installation
to eMMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Treat missing compression node in FIT image as IH_COMP_NONE.
This is implicentely already happening in most places, but for now
was still triggering an annoying warning about initramfs compression
being obsolete despite compression note being absent.
Fix this.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* updated SNAND/SNFI driver brings support for MT7981
* add support for MediaTek NAND Memory bad Block Management (NMBM)
(not used for any boards atm, but could be useful in future)
* wire up NMBM support for MT7622, MT7629, MT7981 and MT7986
* replace some local patches with updated version from SDK
* bring some legacy precompiler symbols which haven't been converted
into Kconfig symbols in U-Boot 2022.07, remove when bumbping to
U-Boot 2022.10:
100-28-include-configs-mt7986-h-from-SDK.patch
Source: https://github.com/mtk-openwrt/u-boot
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MediaTek's ARM Trusted Firmware v2.7+ allows the images inside a FIP
structure to be compressed. Make use of that for boards with NOR flash.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
