Commit Graph

17317 Commits

Author SHA1 Message Date
Yangbo Lu
b72dcd5457 layerscape: fix adjust_link for 10G & 2.5G
Added a linux-4.4 patch to fix adjust_link for 10G & 2.5G.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2017-02-13 10:25:19 +01:00
Chuanhong Guo
57dfbac6ff ramips: Correct switch configuration for Newifi D1
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2017-02-13 10:25:19 +01:00
Martin Blumenstingl
32c9d467e3 lantiq: fix patching the wifi mac address on BTHOMEHUBV3A
The firmware hotplug script tries to read the mac address from a
partition with the name "uboot-env" which does not exist (instead it's
name is uboot_env). This broke calculation of the new checksum (after
patching the mac address) which resulted in ath9k refusing to use the
EEPROM data.

The original error reported by ath9k was:
PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
ath: phy0: Bad EEPROM checksum 0x2523
ath: phy0: Unable to initialize hardware; initialization status: -22
ath9k 0000:00:0e.0: Failed to initialize device

Fixes: a20616863d ("lantiq: use ath9k device tree bindings
binding/owl-loader")

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2017-02-13 07:57:04 +01:00
Hauke Mehrtens
eac4851bfd kernel: MIPS: IRQ Stack: Fix erroneous jal to plat_irq_dispatch
This backports the following fix to our mips IRQ stack patches:
https://patchwork.linux-mips.org/patch/15110/

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-02-12 12:25:52 +01:00
Jonas Gorski
02515f0187 brcm63xx: fix lzma loader for BCM6362
BCM6362 and BCM3380 seem to share the same PRID. Disable serial output
for them until we can find a way to tell them apart reliably.

Fixes: 8f3cfe4ba2 ("brcm63xx: lzma-loader: add BCM3380 support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-02-10 10:51:09 +01:00
Jonas Gorski
f49efcd325 brcm63xx: do a full reset phy cycle
Make sure we do a proper reset of the phy, if the phy reset is defined.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-02-10 10:51:09 +01:00
Jonas Gorski
921cecbdf8 brcm63xx: fix external interrupts on BCM6318
Setting the clear bit for an interrupt seems to cause interrupts to be
deasserted again immediately. So unset the bit for BCM6318 to allow
subsequent interrupts to still work.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-02-10 10:51:09 +01:00
Alexey Brodkin
f25d9cbe48 arc770: backport upstream fix for unaligned access
This commit reverts 42f3c1f ("arc770: fix broken upstream change")
and simultaneously adds back-ported fix from Linus' tree:
a524c218bc94 ("ARC: [arcompact] brown paper bag bug in unaligned
access delay slot fixup").

Note mentioned patch will appear in stable trees soon as well so
IMHO there's not much sense in adding this separate patch in lede/master branch.
As well as we will get rid of it here in 17.01 once we bump 4.4 kernel here
later down the line.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Cc: Jo-Philipp Wich <jo@mein.io>
2017-02-09 09:15:17 +01:00
Claudio Leite
4e2c2b51f5 ramips: fix AR670W partition alignment
mtdsplit_lzma requires that the rootfs be aligned to a block boundary.
Pad the kernel partition to make this so.

Signed-off-by: Claudio Leite <leitec@gmail.com>
2017-02-08 06:16:53 +01:00
Rafał Miłecki
083854f06f bcm53xx: add missing system.sh include
It's needed for macaddr_add.

Fixes: 5ed23223fd ("bcm53xx: set WAN MAC address to don't share one with LAN interface")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-07 11:51:05 +01:00
Jo-Philipp Wich
42f3c1fe1c arc770: fix broken upstream change
Add a patch to revert upstream commit 9aed02feae57bf7a40cb04ea0e3017cb7a998db4
which introduces syntax errors.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-02-07 09:32:47 +01:00
Rafał Miłecki
f2b885d82e bcm53xx: set Netgear R8000 USB LEDs
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-06 20:26:01 +01:00
Stijn Tintel
054ce1624c kernel: update kernel 4.4 to version 4.4.47
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked
broken, except arc770 and arch38 due to broken toolchain.

Runtime-tested on ar71xx, octeon, ramips and x86/64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit d2c4041f02)

Conflicts:
	include/kernel-version.mk
	target/linux/ramips/patches-4.4/997-ralink-Introduce-fw_passed_dtb-to-arch-mips-ralink.patch
2017-02-06 20:13:06 +01:00
Koen Vandeputte
b786a5ffc3 kernel: bump to 4.4.46
Refreshed patches for all supported targets.

Compile-tested on ar71xx, cns3xxx, imx6, mt7621, oxnas and x86/64.
Run-tested on ar71xx, cns3xxx, imx6 and mt7621.

Tested-by: Stijn Segers <francesco.borromini@inventati.org>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit 3becadd56c)
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-02-06 20:13:06 +01:00
Koen Vandeputte
c656cbc56b kernel: bump to 4.4.45
Refreshed patches for all supported targets.

Compiled & tested on cns3xxx & imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit 4d1515070b)
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

Conflicts:
	target/linux/ar71xx/patches-4.4/920-usb-chipidea-AR933x-platform-support.patch
2017-02-06 20:13:06 +01:00
Stijn Segers
ee3067c588 Kernel: bump to 4.4.44
Bump kernel to 4.4.44. Compile-tested on ar71xx, ramips/mt7621 and x86/64.

.44 has been run-tested on the 17.01 branch here on ar71xx and mt7621.

Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
(cherry picked from commit 20996edd68)
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

Conflicts:
	target/linux/ar71xx/patches-4.4/920-usb-chipidea-AR933x-platform-support.patch
	target/linux/ar71xx/patches-4.4/930-chipidea-pullup.patch
2017-02-06 20:13:06 +01:00
Rafał Miłecki
518bb7ae5a bcm53xx: refresh Linux 4.4 config
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-06 17:21:40 +01:00
Rafał Miłecki
8ff8e51cda bcm53xx: image: use one style of adding TARGET_DEVICES entries
It just makes code consistent. This trivial change may be a 17.01
candidate to provide simpler backporting experience.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-06 17:08:13 +01:00
Rafał Miłecki
81f9cd56a2 bcm53xx: backport upstream DTS files for Linksys devices
We dont't build officialy images for them yet due to partitioning
issues.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-06 09:08:06 +01:00
Rafał Miłecki
29c0b575ee bcm53xx: use accepted BCM5301X patches for R8000 and Luxul devices
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-06 09:05:26 +01:00
Rafał Miłecki
41dc50fc27 kernel: backport bgmac support for external PHYs
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-05 22:38:26 +01:00
Rafał Miłecki
aec04e1deb kernel: use upstream accepted bgmac fix for BCM47186B0
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-05 22:38:26 +01:00
Rafał Miłecki
f61044a9b0 kernel: rename bgmac patches to squeeze them
This is a pure rename without any changes. It makes maintaining bgmac
simpler and will hopefully make adding new kernel a bit easier.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-05 22:38:26 +01:00
Mathias Kresin
3f9a194e04 ramips: fix Airlink AR725W factory image build
The factory image can't be bigger than 3328 KByte. If the image is
bigger than that, the gemtek-header tool throws an error and breaks
the build.

Make sure the output file to which the gemtek header should be added
exists and wasn't removed during the check-size step because of it
size. This will prevent hard errors in case the factory image is to big
similar to what is done for sysupgrade images.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-04 12:54:40 +01:00
Hannu Nyman
c53bb974b2 ipq806x: fix wireless macs
Commit 71a39b8 ("ipq806x: Fix wireless support for Netgear Nighthawk X4S
D7800") added a trailing TAB char after the backslash which prevents
the assignment of the correct MACs for wifi devices.

Fixes: FS#451

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[reworded commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-03 19:32:07 +01:00
Rafał Miłecki
5ed23223fd bcm53xx: set WAN MAC address to don't share one with LAN interface
After analyzing numerous NVRAMs and vendor firmwares it seems the base
MAC address is used for LAN interface. WAN interface has different one
which sometimes is set directly in NVRAM and sometines needs to be
calculated.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-03 08:05:32 +01:00
André Valentin
41de9a2e12 ipq806x: fixup nbg6817 internal mmc and switch configuration in DTS
The setting mmc-ddr-1_8v in the platform dts leads to read errors. The
device is unusable and system reboots in a loop. Because NBG6817 is the
only mmc device, I removed it in base dts.

The second change removes settings now present in base dts.

The third change references was a wrong conversion of constants in the switch settings.
Switch now initializes again.

Signed-off-by: André Valentin <avalentin@marcant.net>
2017-02-02 22:49:33 +01:00
Rafał Miłecki
0224e32cd0 kernel: fix BCM54612E PHY support
This backports upstream commit 62e13097c46c ("net: phy: broadcom: rehook
BCM54612E specific init")

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-01 21:12:33 +01:00
Qian Zheng
b313f0d189 ar71xx: fix netgear wndr3700 v1/v2, wndr3800/wndr3800ch switch port mapping
Signed-off-by: Qian Zheng <sotux82@gmail.com>
2017-02-01 17:58:39 +01:00
Qian Zheng
581285c6dc ar71xx: fix netgear wnr2000 v3 switch port mapping
Signed-off-by: Qian Zheng <sotux82@gmail.com>
[Jo-Philipp Wich: fix alphabetical order after merging with gl-ar300 case]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-02-01 17:58:39 +01:00
Qian Zheng
0880105144 ar71xx: fix tl-wr841n-v7 switch port mapping
Signed-off-by: Qian Zheng <sotux82@gmail.com>
[Jo-Philipp Wich: fix alphabetical order]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-02-01 17:58:39 +01:00
Mathias Kresin
2a14335d95 mvebu: fix usb port leds
All mvebu boards have three USB LEDs. The first one is used for the
USB1 port.

There are two LEDs related to the second USB port. The top (bar) LED
gets bright in case any USB device is connected to the second USB port.

If the connected device is an USB 3 (SuperSpeed) device, the small dot
LED bellow the "bar" LED gets also bright.

While at it, use a name for the USB LEDs that matches the names printed
on the case.

Fixes: FS#423, FS#425

Signed-off-by: Kabuli Chana <newtownbuild@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-01 17:56:58 +01:00
Hans Geiblinger
faea9bea44 mvebu: set fan_ctrl.sh only on mamba
Signed-off-by: Hans Geiblinger <cybrnook2002yahoo.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup]
2017-02-01 17:56:58 +01:00
Chris Blake
e9b60b587b x86: add kernel module for sp5100_tco watchdog
This change adds the sp5100_tco driver as a kernel module for the x86
target. Specifically, this can be used by the PCEngines APU2/APU3. The
reason for having this as a kernel module is to allow users to
load/unload it on demand, as the I2C interface on the APU2/APU3 will not
work while this module is loaded. More info can be found on GitHub at
https://github.com/riptidewave93/LEDE-APU2/pull/5#issuecomment-255667736

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2017-02-01 17:45:25 +01:00
Chris Blake
af3ae4b37c x86: Add sp5100_tco AMD patches
This adds the following patches to the x86 target:

sp5100_tco: Add AMD Mullins platform support
sp5100_tco: Add AMD Carrizo platform support
sp5100_tco: fix the device check for SB800 and later chipsets
watchdog: sp5100_tco: properly check for new register layouts

With these added, the sp5100_tco driver can then be used on newer AMD
platforms, such as the PCEngines APU2/APU3 boards.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2017-02-01 17:45:25 +01:00
Jiri Kastner
d6a830ac7e octeon: fix mtd partitions for erlite on cmdline
erlite mtdparts exposes boot0, boot1 and eeprom regions
as read/write.
this patch adds readonly flags, so these regions can't be
modified. same as it is already for ER profile.

Signed-off-by: Jiri Kastner <cz172638@gmail.com>
2017-02-01 17:39:09 +01:00
Zhang Jingye
9c915d1e7b ipq806x: Fix wireless support for Netgear Nighthawk X4S D7800
D7800 has a simular hardware to R7800 and uses dual QCA9980 for both 2.4GHz and 5GHz band.
However there is no proper initialization for them, which causes a kernel panic due to failed firmware loading.

This patch adds d7800 to ath10k caldata extraction list.
I can get two functional wireless bands after making change to it.

Signed-off-by: Zhang Jingye <934526987@qq.com>
2017-02-01 17:37:58 +01:00
Jo-Philipp Wich
ea43d60c18 kernel: ar8327/ar8337: disable ARL access code to avoid lockups (FS#384)
Running ar8327_get_arl_entry() early after boot leads to MDIO related system
lockups on several devices using this driver.

Since dumping the ARL table contens is an optional, uncritical feature, simply
disable the code for now.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-02-01 15:40:19 +01:00
Rafał Miłecki
d5b5339540 bcm53xx: fix LAN MAC address for devices that use eth2 originally
We override default Ethernet interface with eth0 which often uses random
MAC due to missing proper NVRAM entry. Fix this by manually assigning
MAC in the config.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-01 15:27:18 +01:00
Felix Fietkau
01888f90a0 ar71xx: add missing DEVICE_TITLE for mikrotik devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-01 15:00:22 +01:00
Alex Samorukov
198d73b26f ar71xx: Fix mikrotik subtarget default profile for device profile selection
Signed-off-by: Alex Samorukov <samm@os2.kiev.ua>
2017-02-01 14:59:57 +01:00
Alex Samorukov
0780fd5ee6 ar71xx: improve Mikrotik hAP Lite device support
- remove CONFIG_MTD_SPI_NOR_USE_4K_SECTORS
- enable jffs2 support
- fix sysupgrade

Signed-off-by: Alex Samorukov <samm@os2.kiev.ua>
2017-02-01 14:59:52 +01:00
Thibaut VARENE
2cf64afd4e ar71xx: mark soft_config mtd part as writeable for RB-941-2nD
The soft_config partition must be writeable for rbcfg to be able to
enact changes to the routerboot configuration.
The read-only flag was a mistake in the initial patch. Removing it
brings mach-rb941.c in line with all other RB platforms.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-01 14:59:29 +01:00
Felix Fietkau
51b6dd1aed ar71xx: fix up the kernel config for the mikrotik subtarget
Limit enabled devices to routerboards, disable all other devices

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-01 14:59:23 +01:00
Cezary Jackiewicz
3e4b00e6fa ar71xx: fix network config for Mikrotik RB411U
Mikrotik RB411U has only one ethernet port - eth0. This patch allows to create
correct config with one lan section.

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2017-02-01 14:59:17 +01:00
Thibaut VARENE
ca2a03d1f6 ar71xx: add support for RB-941-2nD
Add full support for Mikrotik RB-941-2nD (hAP lite)

Original patch by Sergey Sergeev <adron@yapic.net> and
more information is available here:
https://wiki.openwrt.org/toh/mikrotik/rb941_2nd
I updated and adapted the patch to apply cleanly to LEDE trunk
and added proper numbering for the switch ports (matching case
labels).
Tested working on actual hardware with the information
provided in the above webpage. Sysupgrade works.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-01 14:59:11 +01:00
Felix Fietkau
0656bee36b ar71xx: convert mikrotik routerboard support to UBI
Remove the wget2nand script, drop the need for manual installation,
use sysupgrade instead.

There are now two different NAND images, one for 64 MiB flashes, the
other for >= 128 MiB

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-01 14:58:57 +01:00
Felix Fietkau
e53e44a0ad ar71xx: create a proper default profile for the mikrotik subtarget, drop other profiles
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-01 14:58:52 +01:00
Rafał Miłecki
e3849823e0 kernel: update bcma to fix devm memory leaks
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-01-31 14:45:52 +01:00
Felix Fietkau
bda982b97f ramips: add missing DTS pcie node for WSR-600
Enables PCI bus and support for the MT7603 and RT5592 chips

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-31 10:29:29 +01:00
Alexander Couzens
31b0640906 lantiq: fix unaligned access in xrx200_poll_rx()
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-01-30 10:15:33 +01:00
Sergey Sergeev
ec095b5bf3 ledtrig-netdev: don't cancel work on events for different interfaces
This fixes logic bug(in function netdev_trig_notify) introduced in
0b2991a8ed commit.
Events triggered by different interfaces were stopping work queue so it
wasn't working for tx/rx mode.

Signed-off-by: Sergey Sergeev <adron@yapic.net>
2017-01-29 17:34:29 +01:00
FUKAUMI Naoki
70a6bbd53d ar71xx: prepare jffs2 partition properly in factory.bin for BHR-4GRV2
"pad-rootfs" is required just after "append-rootfs".

Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
2017-01-28 20:32:39 +01:00
Michael Heimpold
f5e8c908bd mxs: remove stale references to obsolete kernel module packages
Commit 29443e2 (mxs: remove modules.mk, select drivers in the kernel config)
missed to remove these references, so cleanup it now.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2017-01-28 20:32:39 +01:00
Rafał Miłecki
d46ce9498c kernel: backport support for BCM54210E PHY
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-01-28 19:12:46 +01:00
Rafał Miłecki
c170848254 kernel: backport support for BCM54810 PHY
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-01-28 19:12:42 +01:00
Rafał Miłecki
2ee7bc0a5e kernel: backport support for BCM54612E PHY
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-01-28 17:34:17 +01:00
Mathias Kresin
66211d0781 lantiq: fix brnImage signature for the VGV7510KW22BRN images
The VGV7510KW22BRN and VGV7519BRN do not have the same brnImage
signature. It was accidentally changed with ba42c1d ("lantiq: un-macro
the image building code").

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-28 12:44:35 +01:00
Rafał Miłecki
6b68635047 bcm53xx: disable building Linksys EA6300 V1 image
This device has 2 TRX partitions (main one and failsafe one) and Linux
may not detect them properly failing to run userspace.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-01-25 10:51:58 +01:00
Felix Fietkau
e9ecb228c9 x86: fix sysupgrades on disks with 4k block size
Even when the disk uses 4k blocks, the partition table still uses units
of 512 byte sectors. Always use ibs=512 for the offsets

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-25 08:14:59 +01:00
Rafał Miłecki
86b4b027cf brcm47xx: backport arch patch with Luxul devices support
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-01-24 23:01:05 +01:00
Felix Fietkau
fc366fde07 lantiq: remove CPU_TYPE:=mips32r2, it gets overwritten anyway
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-24 13:35:47 +01:00
Felix Fietkau
b630d525c8 x86: unify CPU_TYPE for legacy and geode
According to some reports, -march=pentium-mmx is a better choice for
older Geode CPUs than -march=geode anyway.

Bump the minimum architecture of the legacy target from i486 to
pentium-mmx. Anything older is not worth supporting anyway.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-24 13:35:47 +01:00
Felix Fietkau
c2ecf9c37a uml: mark as source-only
Get rid of a special case in the buildbot script

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-24 13:35:47 +01:00
Felix Fietkau
4d73b6b8d0 malta: mark as source-only to avoid wasting build resources
The le64 and be64 subtargets do not share a package architecture with
any other targets, so they are pretty wasteful for a development-only
target.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-24 13:35:47 +01:00
Felix Fietkau
0a4d20fa9c malta: move FEATURES to the target makefile
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-24 13:35:47 +01:00
Felix Fietkau
392cccb7f4 build: remove mips16 feature flag from target makefiles
It can be implicitly derived from the MIPS32 revision support in the
kernel configuration

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-24 13:35:45 +01:00
Felix Fietkau
6193e3cdee ramips/rt288x: switch CPU_TYPE to 24kc
While rt288x only has a MIPS 4KEc processor, it implements the MIPS32r2
architecture just like the 24Kc, so the instruction set should be 100%
compatible.
Switching it to 24kc allows it to share the package architecture with a
lot of other targets instead of creating a special case, saving
buildbot resources.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-24 13:35:09 +01:00
Felix Fietkau
b36e24f39e x86: remove the xen_domu subtarget
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-24 13:30:45 +01:00
Felix Fietkau
296772f939 x86/generic: add xen DomU support
Copy the relevant config options from the xen_domu subtarget

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-24 13:30:39 +01:00
Felix Fietkau
4039b3eba1 lantiq: fix an ethernet stability issue triggered by receving packets during boot
Disabling ethernet during reboot (only to enable it again when the
ethernet driver attaches) can put the chip into a faulty state where it
corrupts the header of all incoming packets.

This happens if packets arrive during the time window where the core is
disabled, and it can be easily reproduced by rebooting while sending a
flood ping to the broadcast address.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-19 14:30:47 +01:00
Felix Fietkau
6538961d6a lantiq: fix spurious irq storm
Since the MIPS IRQ stack patches, lantiq devices were emitting a storm
of messages like this:

[  567.872172] Spurious IRQ: CAUSE=0x1100c300

Fix this by reworking the IRQ dispatch code

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-19 12:34:08 +01:00
Felix Fietkau
0b2991a8ed kernel: make ledtrig-netdev use a work queue for updates
This fixes hangs in igb that happen if the update call interrupts an
already existing dev_get_stats call. In that case the calling CPU
deadlocks because it's trying to acquire the same spinlock recursively.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-16 09:52:59 +01:00
Rafał Miłecki
ea6d10d572 bcm53xx: add pending BCM5301X patches: Netgear R8000 WiFi & Luxul DTS
This specifies wireless limitations for Netgear R8000 making sure people
won't use channels incorrectly (limited performance). There are also 2
new DTS files not used by us yet.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-01-15 23:10:55 +01:00
Rafał Miłecki
ee6cce6b31 kernel: fix bcma serial console regression
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-01-15 23:10:54 +01:00
Pavel Kubelun
8004aa313a ipq806x: refactor ipq8065 device tree
At the moment we have 2 seperate device tree sources: 1 for ipq8064 soc located
in kernel source and 1 custom in LEDE for ipq8065.
ipq8064 and ipq8065 SoCs are completely identical except ipq8065 has higher cpu
frequencies and adjusted corresponding power supply.

This commit makes ipq8065 DTS to contain only specific for ipq8065 DT entries while
pulling all the basic SoC stuff from ipq8064 DTS.

It makes easier to manage ipq806x device trees and instead of committing changes into
2 seperate equal DTS we are ending up with only 1.
It also enables ipq8065 devices to automatically receive changes made in upstream kernel.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-01-15 20:56:30 +01:00
Pavel Kubelun
ca25b4d729 ipq806x: enable hw pseudo random number generator
Enables support for pseudo random number generator in device tree.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-01-15 20:56:30 +01:00
Pavel Kubelun
44b44595dc ipq806x: update eMMC and SDCC3 nodes in device tree
Enable bam dma support for eMMC and SDCC3 in device tree and update nodes
to reflect Qualcomm SDK.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-01-15 20:56:30 +01:00
Pavel Kubelun
45bf3d4f24 ipq806x: disable usb3 phy suspend and add usb tcsr control
According to Qualcomm SDK usb3 phy suspend should be disabled for
ipq806x.
This may solve issue on some ipq806x devices that breaks usb3
storage peripherals during system boot.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-01-15 20:56:30 +01:00
John Crispin
c067011af8 ramips: add back the i2c-mt7621 module
mt7628/88 are still using this module.

Signed-off-by: John Crispin <john@phrozen.org>
2017-01-15 20:45:59 +01:00
Lazar Demin
ab90f15c89 ramips: Added Onion Omega2 and Omega2+
This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io)

Specifications:
- SoC: MediaTek MT7688AN (580MHz, ramips)
- Omega2
  - RAM: 64MB DDR
  - Storage: 16MB NOR SPI flash onboard
- Omega2+
  - RAM: 128MB DDR
  - Storage: 32MB NOR SPI flash onboard + microSD slot
- Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter
- Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port
- Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock)
  - All Docks Provide:
    - Micro-USB port to provide power to the Omega
      - On the Expansion and Mini Docks, can also access the terminal (UART0) via serial
    - USB 2.0 socket connected to Omega
  - Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide:
    - Omega GPIO breakout
    - Allows for connection of Omega Expansions:
      - Ethernet Expansion
      - Relay Expansion
      - PWM Expansion
      - OLED Expansion
      - Ethernet Expansion
      - Proto Expansion
      - Cellular Expansion

Signed-off-by: Lazar Demin <lazar@onion.io>
2017-01-15 17:43:14 +01:00
João Chaínho
ace9d1fb6f ar71xx: Detect USB port on Mikrotik RB750UP
The USB port on Mikrotik RB750UP isn’t detected. This patch provides a fix. Tested and working.

Signed-off-by: João Chaínho <joaochainho@gmail.com>
2017-01-15 17:43:14 +01:00
Rosen Penev
80768ddccd ramips: Add I2C driver to the default kernel config
I made a commit that added the RTC driver to the kernel config with
the intent that it would fix hctosys. Unfortunately while the RTC
driver is in there, it's connected through I2C, the driver for which
comes in module form and is thus loaded late. After this commit, it
works fine.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2017-01-15 17:43:05 +01:00
Petr Štetiar
26e4fee6e2 imx6: kernel: Backport serial port fixes
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2017-01-15 17:41:14 +01:00
Felix Fietkau
1708644f19 kernel: backport MIPS changes introducing a separate IRQ stack
Prevents crashes when IRQs arrive when the current kernel stack context
already contains deeply nested function calls, e.g. when stacking lots
of network devices on top of each other

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-15 18:25:54 +01:00
Hauke Mehrtens
5b089e45a6 kernel: update 4.4 kernel to 4.4.42
Refresh patches on all 4.4 supported platforms.
Compile & run tested: lantiq/xrx200

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-01-13 23:05:36 +01:00
Felix Fietkau
c6a8a23ea2 xburst: remove hack to determine entry point
xburst has CONFIG_BOOT_RAW set, so jumping to the load address is valid

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-13 19:46:45 +01:00
Felix Fietkau
d2424d4b21 malta: remove hack to determine entry point
Malta has CONFIG_BOOT_RAW set, so jumping to the load address is valid

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-13 19:46:45 +01:00
Paul Wassi
9641ceea0c mvebu: simplify etc/board.d/02_network
Unify switch configuration on Linksys WRTxx00AC series.
LAN = eth0, WAN = eth1

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
[Álvaro]: also change WAN LEDs
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2017-01-13 17:12:40 +01:00
Imre Kaloz
f24ffb901e mvsw61xx: add support for MV88E6352
MV88E6352 is used on Linksys WRT3200ACM

Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
2017-01-13 17:12:40 +01:00
Álvaro Fernández Rojas
89ecfa7556 mvebu: several fixes for Linksys WRT3200ACM
- Fix WLAN LEDs definition.
- Fix USB pinctrl definition.
- Remove SDHCI definition.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2017-01-13 17:12:40 +01:00
Felix Fietkau
8935689a8e mxs: gzip ext4 images
Significantly reduces disk usage

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-13 16:59:28 +01:00
Felix Fietkau
515d012e6d arc770: gzip rootfs image to save some space
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-13 16:59:28 +01:00
Felix Fietkau
113dd45092 archs38: gzip rootfs image to save some space
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-13 16:59:28 +01:00
Felix Fietkau
6f57e32f95 mvebu: remove the clearfog-bundle
It is obsoleted by proper SD card image support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-13 16:59:28 +01:00
Felix Fietkau
87b668765e image: when using the new image build code, gzip ext4 images by default
This reduces the amount of hacks in the makefile code.

Remove the apm821xx code to do the same - it was broken and left both
compressed and uncompressed images in $(BIN_DIR)

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-13 16:59:28 +01:00
Felix Fietkau
749918911d x86: disable crashlog
It could cause crashes with some forms of virtualization, and it is
unlikely to work properly with most systems.
It's safer to just disable it.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-13 15:15:09 +01:00
Felix Fietkau
e38fd1eced x86: disable a workaround for a buggy glibc version
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-13 15:13:59 +01:00
Felix Fietkau
27fbf54147 octeon: disable ext4 images
They're pretty large and squashfs images tend to be more useful anyway

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-13 14:54:12 +01:00
Felix Fietkau
dcd8357365 armvirt: add kernel config change missing from 0d44f0cb
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-13 11:05:32 +01:00
Felix Fietkau
d6c77b9d99 ar71xx: default to external USB power on RB-912UAG
There's a GPIO that can switch between power to USB pins for the
internal MiniPCIe slot or the external USB port.
People are more likely to use the external one so enable it by default.
Existing configurations should be unaffected

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-13 10:53:05 +01:00
Felix Fietkau
83eef37400 x86/64: enable the fusion scsi driver
Is it used by VMware Fusion by default. This allows images to boot
without further config changes in VMware.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-13 10:23:42 +01:00
Felix Fietkau
0d44f0cbbc armvirt: enable the USB feature flag
USB devices can be passed through from the host to the guest

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-13 09:15:09 +01:00
Yo Abe
29097b95ba ramips: fix WLI-TX4-AG300N boot and network
Partition label "linux" prevents the root file system to be mounted at
boot time leading to a kernel panic. After changing it to "firmware",
the 2 uimage partitions "kernel", "rootfs" and squashfs "rootfs_data"
are correctly recognized.

The attached IP175C 10/100 MBit switch cannot connect to a link with
fixed 1000Mbit speed. The correct link speed is 100MBit. The switch
is detected and can be configured via mdio bus and should allow two
separable VLANs to be configured for the 4 available ports.

Signed-off-by: Yo Abe <abe.geel@gmail.com>
[picked from openwrt/PR#330]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-13 08:32:35 +01:00
Andrew Yong
3f31029b19 ramips: add support for VoCore2
This patch adds support for the VoCore VoCore2 and its complementary
"ultimate" dock.

Specifications:
- SoC: MediaTek MT7628AN (580MHz, ramips)
- RAM: 128MB DDR2 166MHz
- Storage: 16MB NOR SPI flash onboard + microSD slot on dock
- Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2
            boards with onboard 1x chip antenna
- Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header
- Dock hardware:
  - USB 2.0 socket
  - MicroSD socket
  - 100Mbps Ethernet x1
  - 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S
    DAC/ADC (support WIP)
  - Micro USB for power and console (UART2)

Initial installation:
- VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on
  SSID "VoCore2"
- Connect to VoCore2 by Ethernet or Wi-Fi
- `ssh root@192.168.1.1` (password is "vocore")
- scp/wget/etc. LEDE sysupgrade.bin to VoCore2
- `sysupgrade -n <your image>.bin` (don't keep old config, as the
  original firmware uses Ralink SDK Wi-Fi drivers and not
  mt76+mac80211)
- after sysupgrade completes, Wi-Fi will be disabled by default so use
  Ethernet or the micro USB console to configure Wi-Fi again

Signed-off-by: Andrew Yong <me@ndoo.sg>
2017-01-13 08:32:35 +01:00
David Varga
d7fd1a0f8d ar71xx: enable serial console on Mikrotik RB411/RB433
This patch adds support for serial console on Mikrotik RB411 and RB433
series devices.

Signed-off-by: David Varga <duvi@duvinet.hu>
[picked from FS#377]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-13 08:32:20 +01:00
Daniel Golle
287283e6e3 ramips: rt3883: fix typo in pinctrl lna_g_func
Spotted by forum users
https://forum.openwrt.org/viewtopic.php?pid=347439#p347439

Reported-by: Tom Psyborg <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-01-13 05:44:06 +01:00
Felix Fietkau
90f0ca0ddc arc770: build dtb files in Image/Prepare so that they are available for Device/*
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-11 16:35:03 +01:00
Felix Fietkau
b9713ad630 archs38: build dtb files in Image/Prepare so that they are available for Device/*
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-11 16:35:03 +01:00
Rafał Miłecki
4ce3c41696 bcm53xx: backport upstream bcm53xx spi driver changes
One replaces our local patch and another is just for keeping driver in
sync (license change).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-01-11 15:33:47 +01:00
Felix Fietkau
2e1f6f1682 mvebu: work around an ethernet tx scheduling fairness issue
The hardware queue scheduling is apparently configured with fixed
priorities, which creates a nasty fairness issue where traffic from one
CPU can starve traffic from all other CPUs.

Work around this issue by forcing all tx packets to go through one CPU,
until this issue is fixed properly.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-11 14:56:57 +01:00
Felix Fietkau
3be4c6ca93 kirkwood: only add UBI EOF markers for devices that need it
Fixes issues where the second-stage u-boot already uses UBI.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-11 14:04:18 +01:00
Felix Fietkau
e21cb649a2 ar71xx: disable sub-page writes on routerboard nand drivers
They seem to fail in tests using UBI, and are not used by yaffs2

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-11 13:10:19 +01:00
Felix Fietkau
b7bee2858b kernel: remove linux 4.1 support
The only target still referencing it is omap24xx, and it is marked as
broken.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-11 13:09:33 +01:00
Felix Fietkau
b1dbe6028e ar71xx: fix legacy image build error
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-11 13:09:21 +01:00
Felix Fietkau
1b17f4f260 arc770: fix parallel build issue
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-11 13:02:42 +01:00
Felix Fietkau
3fa2c77e3a archs38: fix parallel build issue
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-11 13:02:41 +01:00
Felix Fietkau
889272d92d ar71xx: fix RB4xx CPLD SPI device mode setup
Commit af79fdbe4a changed the code to use tx_nbits for dual SPI tx
transfers, however the SPI stack only allows this when the device mode
includes the relevant bit as well

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-11 13:02:11 +01:00
Felix Fietkau
c3a8b87773 ar71xx: fix RB4xx SPI driver mode bits
Accept SPI_TX_DUAL in device mode to fix the CPLD driver

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-11 13:02:11 +01:00
Felix Fietkau
80dbaa4ef3 kernel: backport a MIPS SMP icache flush fix
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-11 10:05:08 +01:00
Rafał Miłecki
7c8a36340c kernel: update bcm47xxpart failsafe partition patches
V2 using helper function was sent for upstream kernel

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-01-11 09:54:47 +01:00
Jo-Philipp Wich
7480d3309c kernel: add missing config symbols
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-01-10 22:02:40 +01:00
Felix Fietkau
e9b49a41e2 kernel: add missing config symbol
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 17:49:47 +01:00
Felix Fietkau
c9dd40f628 kernel: remove gpiommc patches / driver
This code was marked as incompatible to Linux 4.4 well over a year ago
and nobody cared, and now it's breaking builds.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 15:45:33 +01:00
Rafał Miłecki
1a5cb4ac1b kernel: add pending bcm47xxpart support for failsafe TRX partition
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-01-10 15:37:22 +01:00
Rafał Miłecki
ef9208c51e kernel: update spi-nor.h include fix with upstream accepted version
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-01-10 15:37:22 +01:00
Rafał Miłecki
b4d2575add kernel: rename bcm47xxpart patches to fit more of them
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-01-10 15:37:21 +01:00
Felix Fietkau
01d9527357 kernel: remove DEVTMPFS platform overrides
Those options are handled via top-level menuconfig instead

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 13:48:53 +01:00
Felix Fietkau
c2fc52ae22 kernel: remove DEVMEM/DEVKMEM platform overrides
Those options are handled via top-level menuconfig instead

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 13:48:53 +01:00
Felix Fietkau
7ff7be96dd omap: build various core drivers into the kernel instead of packaging them
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 13:44:26 +01:00
Felix Fietkau
10f7a8d648 kernel: add missing config symbol
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 13:44:25 +01:00
Felix Fietkau
f5c649d7c6 mpc85xx: build i2c support into the kernel instead of packaging it separately
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 13:44:25 +01:00
Felix Fietkau
96ade7adae mpc85xx: build usb support into the kernel instead of packaging it separately
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 13:44:24 +01:00
Stijn Tintel
0d3dc16931 ar71xx: drop references to madwifi
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 13:02:00 +01:00
Felix Fietkau
06c76e41d7 ppc44x: mark as broken
This target has consistently failed builds for a long time and it does
not look like it has any users left, nor any maintainers.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 12:49:34 +01:00
Felix Fietkau
43a528eb96 kernel: add missing config symbol
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 12:37:13 +01:00
Kabuli Chana
fe876e9ac6 mvebu: Fix up some leds on this series
correct ports, fix power led on rango, tested mamba,shelby,rango

Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
2017-01-10 12:28:32 +01:00
Felix Fietkau
acd0c8c178 kernel: move the gateworks system controller driver to an out-of-tree package
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 12:10:20 +01:00
Felix Fietkau
c00e5a4f09 mpc85xx: enable the crypto acceleration driver in the kernel config instead of packaging it
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 12:10:20 +01:00
Felix Fietkau
a2f6b56c8f imx6: enable the crypto acceleration driver in the kernel config instead of packaging it
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 12:10:20 +01:00
Felix Fietkau
29443e2c94 mxs: remove modules.mk, select drivers in the kernel config
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 12:10:20 +01:00
Felix Fietkau
915d7db9bd mxs: remove obsolete kernel package depending on linux 3.18
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 12:10:20 +01:00
Felix Fietkau
64be6fe9ca mxs: enable the chipidea usb driver in the kernel config instead of packaging it
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 12:10:20 +01:00
Felix Fietkau
7450698957 imx6: enable the chipidea usb driver in the kernel config instead of packaging it
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 12:10:20 +01:00
Felix Fietkau
7f0796d874 imx6: remove kmod-thermal-imx, it is already enabled in the kernel config
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 12:10:20 +01:00
Felix Fietkau
348fedc1a6 imx6: build support for the ventana ethernet expansion board into the kernel instead of packaging it
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 12:10:20 +01:00
Felix Fietkau
c524d1b256 imx6: enable the Freescale SNVS RTC driver in the kernel config instead of packaging it
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 12:10:20 +01:00
Florian Fainelli
e3358b2cc1 malta: Fix README file examples
The example command-lines used references and paths from an older directory
structure.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2017-01-10 08:54:59 +01:00
Antonis Kanouras
f2b6412c72 ramips: Fix VLAN limits for MT7621 GSW
Without this patch swconfig will only allow setting up a total of 16
VLANs, with VLAN ID range of 0-15.

Tested on ubnt-erx.

Signed-off-by: Antonis Kanouras <antonis@metadosis.eu>
2017-01-10 08:18:15 +01:00
Pavel Kubelun
6ebb46a40a ipq806x: fix pvs1_bin voltage in ipq8065 DT
Fixing pvs1 bin voltage as found in GPL tarball and Qualcomm SDK.

Also adjusting smb208_s2a/b minimum voltage to reflect lowest value in pvs table.

Current ipq8065 devices in LEDE choose (based on eFuse data) pvs bin n4, that has
correct values in DT, but in future a new device may choose n1 or n6.

Without this change n1 is semi-correct and n6 is not available, because OPP driver
disregards bins with voltage values that regulator cannot supply.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-01-10 08:11:14 +01:00
Hauke Mehrtens
f036956e1f lantiq: update USB controller initialization
This adds USB initialization fixes for Danube, Amazon SE and xrx300 and
should fix the clock on at least Danube which hopefully closes FS#351.

The xrx200 usb driver now uses more memory for the dwc2 fifos, this was
increased in the chip compared to ar9.

This is based in part on the vendor documentation and the vendor code
base as a reference.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-01-09 23:25:34 +01:00
Hauke Mehrtens
2dac67464d lantiq: fix dma locking problems with SMP
The DMA controller used only local locks, which will not lock the
section against other CPUs, fix this by using spin locks.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-01-09 20:23:28 +01:00
Felix Fietkau
1c6b1ab01d imx6: fix image boot ubifs compression option
--force-compr was added by the xz compression patch, which is gone now.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-09 16:29:45 +01:00
Felix Fietkau
018d80007e kernel: remove ubifs xz decompression support
It has been unused, and less useful than squashfs for cases where flash
space usage matters.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-09 14:07:06 +01:00
Felix Fietkau
50a3bce3eb rb532: drop patch-cmdline from base-files
It is no longer used for upgrading

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-07 17:50:57 +01:00
Felix Fietkau
ad76fdfc8a rb532: switch to UBI, drop yaffs2 support, use sysupgrade for NAND
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-07 17:50:57 +01:00
Felix Fietkau
5b6b0aa267 rb532: convert to new loopback based overlay support
Disable block2mtd support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-07 17:50:57 +01:00
Daniel Golle
b18f75c3d8 oxnas: minor kernel config improvements
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-01-07 15:27:30 +01:00
Daniel Golle
69903c3ee6 oxnas: require image metadata
Now that we generate images with metadata attached, require it in order
to prevent accidentally flashing the wrong image to a board.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-01-07 14:47:04 +01:00
Daniel Golle
870b7bee44 oxnas: remove some kprintf calls from NAND driver
They were added for debugging and I forgot to remove them.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-01-07 14:47:04 +01:00
Hauke Mehrtens
8f0dc92afd lantiq: fix console print for additional boards
I missed 3 boards in this commit:
commit d8dde8c517
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date:   Wed Jan 4 21:53:22 2017 +0100

    lantiq: fix console print

Add bootargs parameters for ARV4525PW, ARV7506PW11 and ARV8539PW22
again.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-01-06 23:00:02 +01:00
Hauke Mehrtens
88ca6390ea kernel: bump to 4.4.40
Refresh patches on all 4.4 supported platforms.
Compile & run tested: lantiq/xrx200

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-01-06 19:38:55 +01:00
Cezary Jackiewicz
4235cd0d95 x86: add kernel module for AMD CS5535/CS5536 audio chipset
Add support for the integrated AC97 sound device on motherboards
with AMD CS5535/CS5536 chipsets.
Tested on Wyse Winterm S30.

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2017-01-06 15:35:20 +01:00
Vladimir Zahradnik
f277f45bd6 yaffs: fix to detect MLC/TLC NAND flash
Signed-off-by: Vladimir Zahradnik <vladimir.zahradnik@gmail.com>
2017-01-06 15:34:13 +01:00
Hauke Mehrtens
d8dde8c517 lantiq: fix console print
The boot loader of many boards provides a kernel boot argument with a
broken console parameter to the kernel. This will be taken before the
stdout-path defined in device tree and the serial will not work on this
board. Multiple boards are affected by this problem, so revert this
patch for all boards. Later we can remove the boot arguments from the
device tree again, after the individual board was checked to work.

This partly reverts this commit:
commit 4995c64857
Author: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Date:   Sun Dec 11 21:55:00 2016 +0100

    lantiq: specify console using stdout-path instead of cmdline argument

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-01-05 23:10:44 +01:00
Matthias Schiffer
1fef80f29c
ar71xx: add support for TP-Link WBS210/510
The devices are mostly identical to the CPE210/510, but use external
antennas.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-01-05 16:01:17 +01:00
Yousong Zhou
0ac00c931c sunxi: use fwtool for checking sdcard images
To achieve this, device tree compatible string was used as boardname and
the value of it will be checked against supported_devices list.

It should be noted that we do not distinguish between
sun5i-a13-olimex-som and sun5i-a13-olinuxino as they share the same dts
file.

The other thing is that we need to gunzip the generated firmware to do
fwtool check.

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2017-01-05 11:09:15 +01:00
Yousong Zhou
5ece16fd23 sunxi: add sysupgrade support
Enalbe builtin support for FAT filesystem as we need to mount boot
partition to store sysupgrade.tgz there

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2017-01-05 11:09:15 +01:00
Yousong Zhou
8a2c56ca03 sunxi: make sdcard image with squashfs as rootfs
Two things that need to be noted

 - There is no partition type id allocated for squashfs yet.  In the
   case of sunxi, any non-zero value should work and we keep it 83 (the
   value for ext4)
 - Remaining spare space within the rootfs partition, not the entire
   sdcard space will be formated as either f2fs or ext4 and mounted as
   overlay to serve the role of rootfs_data.

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2017-01-05 11:09:14 +01:00
Yousong Zhou
4eb0fd8283 sunxi: convert to new image generation method
The new Device/xxx were transformed automatically from old profiles.

Most device names are now taken from basename of the corresponding
kernel device tree file.  Device/sun5i-a13-olimex-som is an exception
because it is not explicitly supported in the kernel yet and shares the
same dts file with Device/sun5i-a13-olinuxino

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2017-01-05 11:09:14 +01:00
Yousong Zhou
6f61d8511e base-files: export x86 platform upgrade functions to common.sh
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2017-01-05 11:09:14 +01:00
Yousong Zhou
d53fcdefbf sunxi: enable loopback device and f2fs support
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2017-01-05 11:09:14 +01:00
Yousong Zhou
76ee28ce9d sunxi: fix dts name for Mele M9
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2017-01-05 11:09:13 +01:00
Yousong Zhou
fa37bdc05a x86: move sysupgrade.tgz only if it exists
To squash error messages at boot time

    mv: can't rename '/mnt/sysupgrade.tgz': No such file or directory

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2017-01-05 11:09:13 +01:00
Felix Fietkau
5f9e367127 kernel: spi: allow setting chipselect gpio to sleep
Fixes issues on some ar71xx MikroTik RouterBoard devices

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-05 11:09:13 +01:00
Felix Fietkau
af79fdbe4a ar71xx: remove a non-upstream spi core patch
- use standard flags instead
- remove dead code from the rb4xx spi drivers

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-05 11:09:13 +01:00
Felix Fietkau
84bd74057f build: use mkhash to replace various quirky md5sum/openssl calls
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-05 11:09:12 +01:00
Daniel Golle
a46c9a4038 oxnas: remove support for pre-4.4 kernels from drivers
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-01-04 19:42:24 +01:00
Stijn Tintel
301301da2b x86/64: enable AES-NI support in kernel
The kernel will detect if the host supports this, so we can just enable
it in the kernel config.

Tested on an APU2 with AES-NI support and a KVM VM on a Xeon E5520 host
without AES-NI support.

Throughput over an IPsec tunnel between these 2 hosts increased from
~63Mbps to ~140Mbps. Ciphers: AES_GCM_16_256/PRF_HMAC_SHA2_512/ECP_521.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-01-04 13:19:58 +01:00
Rafał Miłecki
2406b3488f brcm47xx: generic: include Ethernet drivers in standard image
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-01-04 12:49:03 +01:00
Rafał Miłecki
5f8e3386e0 brcm47xx: drop some personal profiles
WL500GPv1 profile included ath5k which made it usable only for people
who decided to replace default BCM4318 card with Atheros one. We can't
have profile for every possible configuration. If someone adjusts hw in
such a way he can always install a proper package.

WRTSL54GS profile got extra packages for a specific USB usage. Our
standard profile provides basic USB and we should stick to this. We
can't make everyone happy by including packages for all common USB use
cases and all common filesystems.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-01-04 12:24:01 +01:00
Rafał Miłecki
d091b2c381 brcm47xx: generic: drop standalone profiles duplicating device ones
We have identical profiles for these devices thanks to DEVICE_PACKAGES.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-01-04 12:16:09 +01:00
Rafał Miłecki
b138e690e5 brcm47xx: generic: specify DEVICE_PACKAGES for all devices
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-01-04 11:55:45 +01:00
Rafał Miłecki
11c41a0ea9 brcm47xx: fix bgmac package
With all recent patches & changes it needs more modules.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-01-04 11:55:39 +01:00
Jo-Philipp Wich
38a8cea063 powerpc: boot: fix build with parallel make
The powerpc boot wrapper Makefile is not parallel build safe, causing fixdep
to fail reading dependency files of the addnote, hack-coff and mktree
utilities when concurrently building different image targets.

A typical failure looks like:

      Building modules, stage 2.
      HOSTCC  arch/powerpc/boot/addnote
      HOSTCC  arch/powerpc/boot/hack-coff
      DTC     arch/powerpc/boot/taishan.dtb
      HOSTCC  arch/powerpc/boot/addnote
      HOSTCC  arch/powerpc/boot/hack-coff
      MODPOST 800 modules
    fixdep: error opening depfile: arch/powerpc/boot/.hack-coff.d: No such file or directory
    scripts/Makefile.host:91: recipe for target 'arch/powerpc/boot/hack-coff' failed
    make[5]: *** [arch/powerpc/boot/hack-coff] Error 2
    make[5]: *** Waiting for unfinished jobs....
    fixdep: error opening depfile: arch/powerpc/boot/.addnote.d: No such file or directory
    scripts/Makefile.host:91: recipe for target 'arch/powerpc/boot/addnote' failed
    make[5]: *** [arch/powerpc/boot/addnote] Error 2
    rm arch/powerpc/boot/taishan.dtb
    arch/powerpc/Makefile:263: recipe for target 'cuImage.taishan' failed
    make[4]: *** [cuImage.taishan] Error 2
    make[4]: *** Waiting for unfinished jobs....

Add a GNU make specific .NOTPARALLEL pseudo rule to enforce sequential building
of the addnote, hack-coff and mktree executables.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-01-04 10:49:40 +01:00
Rafał Miłecki
18152e71d8 brcm47xx: mips74k: specify DEVICE_PACKAGES for all devices
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-01-04 09:36:34 +01:00
Rafał Miłecki
1d74f78877 brcm47xx: legacy: specify DEVICE_PACKAGES for all devices
This allows more feature complete images. Of course it affect the size,
e.g. enabling b43 bumped rootfs from 1569618 to 2029122 for me.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-01-04 09:35:46 +01:00
Victor Shyba
e2f866d63a generic: mtd: add lock/unlock support for f25l32pa
This chip has write protection enabled on power-up, so this flag is
necessary to support write operations.

Signed-off-by: Victor Shyba <victor1984@riseup.net>
2017-01-03 20:09:41 +01:00
Victor Shyba
d6c831e0e5 generic: mtd: backport SPI_NOR_HAS_LOCK
This flag was added to 4.9 with upstream commit
76a4707de5e18dc32d9cb4e990686140c5664a15.

Signed-off-by: Victor Shyba <victor1984@riseup.net>
[refresh and adjust platform patches, fix commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-03 19:58:00 +01:00
Yutang Jiang
799d0dddf6 layerscape: add ls2088ardb device support
The QorIQ LS2088A processor is built on the Layerscape
architecture combining eight ARM A72 processor cores
with advanced, high-performance datapath acceleration
and network, peripheral interfaces required for
networking, telecom, wireless infrastructure, aerospace
applications and general-purpose embedded applications.

Features summary:
- Eight 64-bit ARM v8 Cortex-A72 CPUs
- Two 64-bit DDR4 SDRAM memory controller with ECC
- One 32-bit DDR3 SDRAM memory controller with ECC
- Data path acceleration architecture 2.0 (DPAA2)
- Ethernet interfaces
- IFC, 4 PCIe, 2 SATA, 2 USB, 1 SDXC, 2 DUARTs etc

Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
2017-01-03 15:19:15 +01:00
Yutang Jiang
1866368a8a layerscape: add ls1088ardb device support
LS1088A is an ARMv8 implementation combining eight ARM A53 processor
cores. The LS1088ARDB is an evaluatoin platform that supports the
LS1088A family SoCs.

Features summary:
- Eight 64-bit ARM v8 Cortex-A53 CPUs
- Data path acceleration architecture 2.0 (DPAA2)
- Ethernet interfaces
- QUADSPI flash, 3 PCIe, 2 USB, 1 SD, 2 DUARTs etc

Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
2017-01-03 15:19:15 +01:00
John Crispin
91dab05918 ixp4xx: drop 3.18 config/patches
the default has been 4.4 for a while now

Signed-off-by: John Crispin <john@phrozen.org>
2017-01-02 21:06:13 +01:00
Mathias Kresin
b35a41c139 generic: backport dwc2 kernel panic fix
In case the soft reset in dwc2_core_reset() timeouts, the
hsotg->core_params are freed albeit it is owned by the core. This
results into a kernel panic as shown in FS#351.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-02 19:16:54 +01:00
L. D. Pinney
b28e94d4bf ramips: MiWiFi Nano fixes
Use the the dt-bindings macros and add the reset button.

Set the correct polarity for the LEDs and drop the default state.
Remove all trigger for the LEDs. According to the manual the LEDs are
only used to show the operation state, where blue means normal
operation.

Use the MAC-Addresses stored in EEPROM for the ethernet and the
wireless interface.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
[use leds only for boot status indication, add proper commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-02 19:16:54 +01:00
Hauke Mehrtens
321aca6661 oxnas: fix syntax in ox820-akitio.dts
This commit introduced a syntax error in ox820-akitio.dts which is
fixed now:
commit 5cde94d9ab
Author: Daniel Golle <daniel@makrotopia.org>
Date:   Sat Sep 24 01:14:53 2016 +0200
    oxnas: backport upstream NAND driver

This caused the folowing error message in the build bot:
Error: arch/arm/boot/dts/ox820-akitio.dts:146.3-147.1 syntax error
FATAL ERROR: Unable to parse input tree
scripts/Makefile.lib:293: recipe for target 'arch/arm/boot/dts/ox820-akitio.dtb' failed
make[5]: *** [arch/arm/boot/dts/ox820-akitio.dtb] Error 1

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-01-02 13:34:57 +01:00
Daniel Golle
3e2c60e476 oxnas: append metadata to sysupgrade image
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-01-01 10:08:04 +01:00
Daniel Golle
5cde94d9ab oxnas: backport upstream NAND driver
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-01-01 10:07:58 +01:00
Daniel Golle
ae21033e76 oxnas: drop support for kernel 4.1
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-01-01 10:07:40 +01:00
Daniel Golle
1f7a3584e5 oxnas: switch to kernel 4.4
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-01-01 10:07:05 +01:00
Felix Fietkau
4731f02fa2 kirkwood: fix ubi partition name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-30 12:58:20 +01:00
Felix Fietkau
83d59453c0 kirkwood: fix sysupgrade for non-dockstar NAND devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-30 12:58:20 +01:00
Rafał Miłecki
8f5cf323c4 brcm47xx: drop standalone Netgear WGT634U profile
We have profile for this device thanks to DEVICE_PACKAGES now.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: Russell Senior <russell@personaltelco.net>
2016-12-30 09:23:07 +01:00
Rafał Miłecki
b1bdb6e5ea brcm47xx: specify DEVICE_PACKAGES for Netgear WGT634U
This allows using it nicely with PER_DEVICE_ROOTFS.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: Russell Senior <russell@personaltelco.net>
2016-12-30 09:22:55 +01:00
Rafał Miłecki
c5ca3043d1 bcm53xx: drop unused source file of bcm53xxspiflash
We don't use this driver since commit 741715331a ("bcm53xx: switch to
m25p80 and drop bcm53xxspiflash").

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-12-29 18:07:01 +01:00
Rafał Miłecki
ef4fc00c91 brcm47xx: mips74k: fix typo in Netgear WN3000RP model name
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-12-29 09:41:00 +01:00
Rafał Miłecki
939ef157da ramips: fix NixcoreX1 profiles
There was a typo in Makefile that prevented using these profiles.

Fixes: a75ce960ac ("ramips: use different board names for variants")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-12-28 23:05:24 +01:00
Sven Roederer
19059d84a4 linux: correct deps for x86-xen-domu target
depending packages have been moved to kernel-config
- kmod-xen-kbddev in 9fde361
- kmod-xen-fs, kmod-xen-evtchn, kmod-xen-netdev in 018807d

this will also fix imagebuilder

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
2016-12-28 10:35:02 +01:00
Felix Fietkau
9c402d03e6 kirkwood: enable initramfs images by default
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-27 12:52:18 +01:00
Hauke Mehrtens
2e101b5e66 ppc44x: fix build of crypto4xx_core.c
crypto4xx_probe() is in the __init section and referenced by code form
other sections, which causes a build error. Backport a patch from
mainline kernel to fix this.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-12-25 15:19:20 +01:00
John Crispin
9998bc5ef7 lantiq: fix falcon build
The following commit changed the build templates name but forgot to
update the TARGET_DEVICES variable properly.

commit f9226158be (lantiq: rename EASY98000 to EASY98000NOR)

Signed-off-by: John Crispin <john@phrozen.org>
2016-12-25 09:52:11 +01:00
Hauke Mehrtens
f9226158be lantiq: rename EASY98000 to EASY98000NOR
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-12-24 14:55:45 +01:00
Felix Fietkau
41b63b50d1 rb532: remove linux 4.1 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-24 12:02:11 +01:00
Florian Fainelli
b69314ea99 rb532: Switch to kernel 4.4
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2016-12-24 12:02:10 +01:00
Florian Fainelli
002264d5b1 rb532: Backport fix to resolve oops during korina_restart
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2016-12-24 12:02:10 +01:00
Florian Fainelli
7a340a5cd0 rb532: Add support for kernel 4.4
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2016-12-24 12:02:10 +01:00
Florian Fainelli
db553ffb34 rb532: Fix initramfs kernel images
The generic lzma-loader uses vmlinux.lzma as an input to compress so we
need to provide a lzma compressed version of the initramfs kernel.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2016-12-24 12:02:10 +01:00
Mathias Kresin
ea9b71e5b1 lantiq: drop the FRITZ7360SL led-dsl alias
The power LED can not be used for indicating the xDSL line state and
the in system (boot) state at the same time in LEDE.  As soon as the
xDSL Line goes down, the power LED is switched off.

During xDSL handshake the power led would blink with the same or a
similar pattern as during boot.

Both might confuse users.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
7dd42d610d lantiq: add FRITZ7360SL phy reset gpios
Due to a hardware bug of Atheros 8030 phys, the driver need to reset
the phys on link state change.

Use the correct compatible string for the at903x phys connected to
switch port 0 and 1.

Fix the pinmux of the gpio lines connected to the reset pin of the phys
and define the reset-pins to let the driver do the fixups.

Fixes FS#343

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
9aa420b00e lantiq: fix DGN1000B boot status leds
The alias node should not be a child of the chosen node.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
0cf581ca3a ramips: use new image build code for more devices
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
a75ce960ac ramips: use different board names for variants
Use different names for flash size related board variants, to make sure
that only images for the actual flash size are considered as valid by
the image validation code.

Remove the flash size suffix from the string returned by
ramips_board_detect() to ensure that existing scripts relying on the
former used boardname are still working.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
29f5e643ad ramips: sort rt305x image file alphabetical
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
d2b1148e75 ramips: use D-Link DIR-600 B1 image for B2 version
Everything set for the B1 is identical to the values uses for the B2
version.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
d2b6bf1416 ramips: fix image validation errors
The name from the Device define will be used in the metadata. Due to
typos/different spelling, this name might not match the one exported in
/lib/ramips.sh.

Fix all name mismatches which were found by checking if the name used
in the metadata exists in /lib/ramips.sh.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Mathias Kresin
ae3ac76e56 ramips: use destinct 11AC NAS board name
Use a distinct board name even if the board is near to identical to
the WeVO W2914NS v2.

To make sure that a 11AC NAS image can not be installed on a
WeVO W2914NS v2, both board need to use different names.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Felix Fietkau
a18488a0aa orion: remove linux 3.18 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-24 09:40:46 +01:00
Felix Fietkau
0d5ba94088 orion: enable SoC drivers in the kernel config
Clean up packaged modules

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-24 09:40:46 +01:00
Felix Fietkau
49e81f9fe4 kirkwood: clean up profiles, move to image makefile
Adds support for per-device rootfs

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-24 09:40:46 +01:00
Felix Fietkau
9a1f441ac8 kirkwood: enable SoC drivers in the kernel config
Clean up packaged modules

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-24 09:40:46 +01:00
Felix Fietkau
44447f6882 kirkwood: clean up FEATURES
Remove dt: it is implicitly enabled based on the kernel config
Remove tar.gz and jffs2_nand: Legacy build code has been removed,
NAND devices are only supported with UBI now.
Remove ubifs: deprecated, use squashfs images instead

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-24 09:40:46 +01:00
Felix Fietkau
2eb1cc3dfc kirkwood: remove legacy image build code
This has been mostly non-functional for a while now

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-24 09:40:46 +01:00
Felix Fietkau
c9e4cf2299 kirkwood: convert iconnect, ib62x0 and pogoplug_e02 to the new image build code
Update the correspoding u-boot configs to stop relying on
kernel-in-rootfs, which was removed a while back

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-24 09:40:46 +01:00
Henryk Heisig
4f033b2da6 ramips: fix tplink image building fix sysupgrade firmware on MR200
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-12-24 06:52:12 +01:00
Henryk Heisig
3a6353d910 ramips: enablemodem: move /lib/ramips.sh to start()
Fix build error: /etc/init.d/enablemodem: line 2: /lib/ramips.sh: No such file or directory

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-12-24 06:51:59 +01:00
Jo-Philipp Wich
29cc927ef5 generic: ar8216: fix invalid bounds check imported from ChromeOS (FS#347)
The priv->vlan_id member is of size AR8X16_MAX_VLANS, not AR8X16_MAX_PORTS,
so check for the proper maximum value in order to avoid capping valid VLAN IDs
to 7 (AR8X16_MAX_PORTS - 1).

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-23 19:24:14 +01:00
Felix Fietkau
d44c6ec1ce Revert "arm64: boot-wrapper: Add mirror"
This reverts commit ef258a0a41.
Similar to 43c09f2885, multiple git
mirrors are not supported

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-22 21:08:17 +01:00
Felix Fietkau
c7c1cf5618 treewide: clean up and unify PKG_VERSION for git based downloads
Also use default defintions for PKG_SOURCE_SUBDIR, PKG_SOURCE

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-22 16:42:21 +01:00
Tedaz
1831e61699 x86/64: enable Hyper-V support in the x86_64 kernel config
Enabled Hyper-V network interface card driver, display adapter driver,
storage driver, keyboard driver, mouse driver and Hyper-V utility and
EFI boot support in the kernel for subtarget x86/64.
Convert the img file to vhd by Ubuntu qemu-img, rather than by the buildroot's
built-in qemu-img.

Tested on Windows Server 2008 r2 and 2012 r2 Gen1 and Gen2 VMs.

Signed-off-by: Tedaz <tedaz99999@hotmail.com>
2016-12-22 16:42:19 +01:00
Henryk Heisig
c8043137bb ramips: Add support to TP-Link Archer MR200
CPU: MT7620N 580MHz
Flash: 8MB
RAM: 64MB
build-in modem 3G/4G
four ethernet port 10/100Mbps

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-12-22 15:03:30 +01:00
Vitaly Chekryzhev
190ee7d86b ramips: add support for ZyXEL Keenetic Omni / Omni II
Factory image can be installed via Zyxel WebUI.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2016-12-22 15:03:13 +01:00
Radek Dostál
3561d89ad6 ar71xx: RE450: enable building of TP-Link RE450
Signed-off-by: Radek Dostál <rd@radekdostal.com>
2016-12-22 14:50:06 +01:00
Tal Keren
9c475eca3e ar71xx: add support for TP-Link RE450
Add full support for TP-Link RE450.
The wireless SoC is similiar to Archer C7: QCA9558 + QCA9880 (pci).
The ethernet interface is AR8035, but the mdio is connected to the gpio and
the chipset builtin mdio bus isn't used, which is unique (and weird), so the
kernel gpio mdio module is used.
The two ethernet leds are connected to the GPIO, so they are both configured,
one to indicate link status and the other to indicate data transfer.

The generation of the image was added to the image Makefile.
The return value of tplink-safeloader is not ignored anymore (to fail on error)

The result factory image is flashable from the stock web ui.

Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: ar71xx: RE450: do not build RE450 for nand]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
[hyniu@o2.pl: ar71xx: RE450: Renaming LED accordance with the standard]
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[jo@mein.io: squash fixes from Radek and Henryk into original commit]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-22 14:50:05 +01:00
Radek Dostál
236fc232bb ar71xx: sort items in 11-ath10k-caldata alphabetically
Requested-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Radek Dostál <rd@radekdostal.com>
2016-12-22 14:50:05 +01:00
Tal Keren
0d9d980ecd firmware-utils: kernel image generator for TP-Link RE450
The firmware image that is used in TP-Link RE450 (and some more devices from
the RE series) is tplink-safeloader.
In the kernel partition, the kernel is compressed in a regular tp-link
firmware that is just used for booting. Since it is only used for compressing
and booting, only four fields are filled in the header:
Vendor, version, kernel load address and kernel entry point.
mktplinkfw-kernel is a simpler version of mktpolinkfw that generate such
images. It also specifies the hardware id (as it is in the product info
section), so when doing a sysupgrade - the existing code will check for
hardware compatibility.

Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: add build target to .../image/tp-link.mk]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
2016-12-22 14:50:05 +01:00
Matthias Schiffer
324bdf3ecc
ar71xx: remove redundant -j from TL-WR1043ND v4 kernel build command
mktplinkfw ignores -j in combined mode, the EOF marker is added by
tplink-safeloader.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-12-21 23:29:00 +01:00
Alexandru Ardelean
81a2f9d6f8 target/linux/x86/image: add explicit prefix to grub-mkimage command
In the latest version of grub-mkimage, the prefix option is mandatory.
Not supplying it fails with:
```
Prefix not specified (use the -p option).
```

In grub-2.02-beta2 a DEFAULT_DIRECTORY was defined
in `include/grub/osdep/hostfile_unix.h` as:
```
 #if defined (__NetBSD__)
 /* NetBSD uses /boot for its boot block.  */
 # define DEFAULT_DIRECTORY  "/"GRUB_DIR_NAME
 #else
 # define DEFAULT_DIRECTORY  "/"GRUB_BOOT_DIR_NAME"/"GRUB_DIR_NAME
 #endif
```

Where:
* GRUB_BOOT_DIR_NAME == boot
* GRUB_DIR_NAME == grub

This was used if the -p option was omitted.

Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
2016-12-20 16:24:21 +01:00
Ludwig Thomeczek
1a4d07c2c5
ar71xx: add support for TP-LINK WR1043ND v4
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
2016-12-20 14:38:48 +01:00
Matthias Schiffer
0495181529
ar71xx: rename mktplinkfw-initramfs to more generic mktplinkfw-combined
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-12-20 14:38:48 +01:00
John Crispin
c21af889bb brcm2708: unbreak the spidev build
a generic patch made this patch fail to apply cleanly leading to aborted builds

Signed-off-by: John Crispin <john@phrozen.org>
2016-12-20 13:47:57 +01:00
John Crispin
87522a7bf2 linux: drop deprected hifn795x patch
this was needed years ago by the OCF

Signed-off-by: John Crispin <john@phrozen.org>
2016-12-20 13:43:30 +01:00