With the introduction of the generic OpenVPN hotplug mechanism, wrapped
--up and --down scripts got the wrong amount and order of arguments passed,
breaking existing configurations and functionality.
Fix this issue by passing the same amount of arguments in the same expected
order as if the scripts were executed by the OpenVPN daemon directly.
Ref: https://github.com/openwrt/openwrt/pull/1596#issuecomment-668935156
Fixes: 8fe9940db6 ("openvpn: add generic hotplug mechanism")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This package provides the necessary files to translate `config dsa_vlan`
and `config dsa_port` sections of `/etc/config/network` into appropriate
bridge vlan filter rules.
The approach of the configuration is to bridge all DSA ports into a logical
bridge device, called "switch0" by default, and to set VLAN port membership,
tagging state and PVID as specified by UCI on each port and on the switch
bridge device itself, allowing logical interfaces to reference port VLAN
groups by using "switch0.N" as ifname, where N denotes the VLAN ID.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
RT3x5x seems to work fine with kernel 5.4. Set the default kernel
version to 5.4 to bring this to a broader audience.
Since 4 of 6 targets are on kernel 5.4 now, invert the kernel
version setup logic in Makefile/target.mk files.
Tested on ZyXEL Keenetic.
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[invert version setup logic]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
WIZnet WizFi630s board name is written slightly different it its OEM
OpenWrt firmware. This causes an incompatibility warning during flashing
with sysupgrade. This patch is adding the vendor board name to the
supported devices list to avoid this warning. For initial flashing you
can use sysupgrade via command line or luci beside of TFTP.
Do not keep the OEM configuration during sysupgrade.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
This uses upstream qcom-ipq8064-v1.0.dtsi and modifies it by patches
instead of keeping a local version. As a consequence:
- we use a part of the shared definitions there and update device
DTS files accordingly
- we move additional stuff from our local v1.0.dtsi to the patch
- we drop partitions, LEDs and keys from the file as we will
implement them differently anyway
Like with the previous patch, this follows the idea that a diff
from upstream might be easier to handle than a big file of our
own with different distribution pattern of properties.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Though a qcom-ipq8064.dtsi file exists upstream, we still do overwrite
it with a full version of our own in the ipq806x target. About half of
the contents of our file are upstream content, the other half are local
improvements.
To prevent us from having a lot of code maintained twice in parallel,
this adjusts the target to use the upstream qcom-ipq8064.dtsi. Our
local changes are arranged into three patches, the first pulling a
commit from upstream, the second doing a few small adjustments, and
the third adding all additional stuff.
This should get us the best of both worlds.
The property "ports-implemented" on sata@29000000 is moved to
2nd-level DTSI files as kernel defines it there as well.
While at, rename 080-ARM-dts-qcom-add-gpio-ranges-property.patch to
include the kernel version where it's added upstream.
Even though this might look more complicated in the first place,
the aim is to bring our files closer to upstream, so we can benefit
from changes directly and vice-versa. After all, this drop about
650 lines just copied from the upstream DTSI file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
212f836 ubus: rename JSON-RPC format related functions
628341f ubus: use local "blob_buf" in uh_ubus_handle_request_object()
9d663e7 ubus: use BLOBMSG_TYPE_UNSPEC for "params" JSON attribute
77d345e ubus: drop unused "obj" arguments
8d9e1fc ubus: parse "call" method params only for relevant call
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
WIZnet WizFi630S is using only 3 of the phy ports. The unused phy ports
draw unnecessarily power. This is disabling the unused phy ports.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
That file was added accidentally in v3 of the patch and I haven't
properly reviewed that patch before pushing it.
Fixes: 656b562aff ("scripts: Add Buildbot dump-target-info.pl script")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This enables Random Number Generator support on Northstar (described in
DT with brcm,bcm5301x-rng).
It's also a workaround for OpenWrt bug with kernel config causing:
Broadcom BCM2835/BCM63xx Random Number Generator support (HW_RANDOM_BCM2835) [Y/n/m/?] (NEW)
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The script comes from buildbot.git[0] and is used to print available
targets and architectures, which are then build.
As the buildbot clones openwrt.git anyway, the script might as well live
here to be used for other cases as well, e.g. determining what
architectures are available when building Docker containers or show
developers an overview which architectures are used by which target.
It's called with either the parameter `architectures` or `targets`,
showing architectures followed by supported targets or targets, followed
by the supported architectures:
$ ./scripts/dump-target-info.pl architectures
aarch64_cortex-a53 bcm27xx/bcm2710 mediatek/mt7622 mvebu/cortexa53 sunxi/cortexa53
aarch64_cortex-a72 bcm27xx/bcm2711 mvebu/cortexa72
...
$ ./scripts/dump-target-info.pl targets
apm821xx/nand powerpc_464fp
apm821xx/sata powerpc_464fp
...
In the future the the script could be removed from the buildbot
repository and maintained only here.
Rename `dumpinfo.pl` to `dump-target-info.pl` to improve verbosity of
filename.
[0]: https://git.openwrt.org/?p=buildbot.git;a=blob;f=scripts/dumpinfo.pl;h=aa97f8d60379076a41b968402e9337cea824ece5;hb=HEAD
Signed-off-by: Paul Spooren <mail@aparcar.org>
TP-Link RE200 v3 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN like the v2.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 8x LED (GPIO-controlled), 2x button
Unverified:
- UART header on PCB (57600 8n1)
There are 2.4G and 5G LEDs in red and green which are controlled
separately.
MAC addresses
-------------
MAC address assignment has been done according to the RE200 v2.
The label MAC address matches the OpenWrt ethernet address.
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Recovery
--------
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.
The device has not been opened for adding support. However, it is expected
that the behavior is similar to the RE200 v2. Instructions for serial console
and recovery may be checked out in commit 6d6f36ae78 ("ramips: add support
for TP-Link RE200 v2") or on the device's Wiki page.
Signed-off-by: Richard Fröhning <misanthropos@gmx.de>
[adjust commit title/message, sort support list]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* compat: rhel 8.3 beta removed nf_nat_core.h
* compat: ipv6_dst_lookup_flow was ported to rhel 7.9 beta
This compat tag adds support for RHEL 8.3 beta and RHEL 7.9 beta, in addition
to RHEL 8.2 and RHEL 7.8. It also marks the first time that
<https://www.wireguard.com/build-status/> is all green for all RHEL kernels.
After quite a bit of trickery, we've finally got the RHEL kernels building
automatically.
* compat: allow override of depmod basedir
When building in an environment with a different modules install path, it's
not possible to override the depmod basedir flag by setting the DEPMODBASEDIR
environment variable.
* compat: add missing headers for ip_tunnel_parse_protocol
This fixes compilation with some unusual configurations.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
For the TP-Link 4M devices with tplink-v2-image recipe
(mktplinkfw2.c), there are two different flash layouts based
on the size of the (u)boot partition:
device uboot OEM firmware OpenWrt (incl. config)
tl-wr840n-v5 0x20000 0x3c0000 0x3d0000
tl-wr841n-v14 0x10000 0x3d0000 0x3e0000
In both cases, the 0x10000 config partition is used for the firmware
partition as well due to the limited space available and since it's
recreated by the OEM firmware anyway.
However, the TFTP flashing process will only copy data up to the
size of the initial (OEM) firmware size. Therefore, while we can
use the bigger partition to have additional erase blocks on the
device, we have to limit the image sizes to the TFTP limits.
So far, only one layout definition has been set up in mktplinkfw2.c
for 4M mediatek devices. This adds a second one and assigns them
to the devices so the image sizes are correctly restrained.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since most of the DTS file names follow a common scheme now, let's
update the automatically generated DEVICE_DTS value and get rid
of some DEVICE_DTS and all BOARD_NAME entries for individual devices.
This should specifically make the job easier for developers adding
new devices, as they are not tempted to copy over BOARD_NAME anymore.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
We currently support four versions of binutils in parallel. Let's
just keep the latest two and drop the older ones before the next
one comes around.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ifconfig is effectively deprecated for quite some time now. Let's
replace the remaining occurrences for packages by the
corresponding ip commands now.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ifconfig is effectively deprecated for quite some time now. Let's
replace the remaining occurrences for our target setup by the
corresponding ip commands now.
Note that this does not touch ar71xx, as it will be dropped anyway,
and changing it would only make backports harder.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Instead of just printing a warning that an image is too big, also
print both actual size and limit in the string:
WARNING: Image file somename.bin is too big: 2096101 > 1048576
Since the kernel size is checked via the same function (if
KERNEL_SIZE is specified), this will also apply to the kernel
image size check.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Commit 1bfbf2de6d ("ar71xx: serial: core: add support for boot console
with arbitrary baud rates") added support for arbitrary baud rates which
enabled 250000 baud rate for Yun. But the patch was not ported to kernel
4.9, and since then the kernel set its baud rate to 9600. This commit ports
the patch to kernel 4.14, thereby restoring the serial console of Yun.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Commit 05d73a2a73 enabled GPIO on ethernet LED, but proper LED setup was
not added then. This commit fixes it by reverting the change on the LED.
Fixes: 05d73a2a73 ("ar71xx: Arduino Yun board 'WLAN RST' button support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Commit bb46b635df changed its partition scheme, but sysupgrade image
validation still uses the old format. This commit fixes it so that
force flag is not needed for sysupgrade.
Fixes: bb46b635df ("ar71xx: move Arduino Yun to generic building code")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This reverts commit 077253dd66.
The output enable pins should be disabled by default, and only enabled when
used. Otherwise unwanted conflicts might occur between MCU and SoC pins.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The recipe check-kernel-size is not used in the entire tree. Instead,
we already check the size of the kernel image in Device/Build/kernel
in image.mk via check-size function if KERNEL_SIZE is defined.
Therefore, drop the function. Using it would be redundant anyway.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The current LICENSE file contains some form feed (FF) characters instead
of recently popular line feed (LF) characters. Also update to the latest
address of the Free Software Foundation. Lastly center some captions, as
suggested by the official GNU LICENSE distribution[0].
Historical changes of GPL-2.0 LICENSE file are availalbe[1].
[0]: https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
[1]: https://github.com/pombredanne/gpl-history
Signed-off-by: Paul Spooren <mail@aparcar.org>
checkpatch.pl uses a list of files to detect the root OpenWrt
directory. This includes README, which has been renamed to
README.md in the previous commit.
Update the file name in checkpatch.pl to prevent errors like the
following when running the script:
Must be run from the top-level dir. of a OpenWrt tree
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The README is no longer important to only developers but also users.
Reflect that by adding valuable information for everyone new to OpenWrt!
Sunshine
Signed-off-by: Paul Spooren <mail@aparcar.org>
[remove trailing whitespace and empty line at EOF]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Move the image preparation and nand-utils package selection into
common device definitions for NOR/NAND devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Update the openvpn sample configurations to use modern options in favor
of deprecated ones, suggest more sane default settings and add some
warnings.
* Add tls_crypt and ncp_disable to the sample configuration
* Replace nsCertType with remote_cert_tls in client sample configuration
* Comment out "option compress", compression should not be preferred
* Advise 2048-bit Diffie-Hellman parameters by default
* Add warnings about compression and use of Blowfish (BF-CBC)
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
The wg utility compiles and runs without issues in MIPS16 mode, despite setting
PKG_USE_MIPS16:=0 in the makefile. Let's remove this, allowing for a substantial
size reduction of the wg executable. Since wg is a just a configuration utility,
it shouldn't be performance-critical, as the crypto heavy-lifting is done on the
kernel side.
wg sizes for both modes:
MIPS32: 64309 bytes
MIPS16: 42501 bytes
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
>From an email conversation with the person responsible for upstreaming
the exFAT driver, it seems the staging one in kernel 5.4 is not so
good. Excerpts below.
Namjae Jeon:
Hm... exfat in 5.4 kernel that we did crap shit long time ago is
contributed by someone who we don't know.
This version is unstable and low quality code. We have been improving
it continuously.
and staging version exfat is removed from linux 5.7 kernel.
linux exfat oot version is a backport of exfat in linux 5.7 kernel to
support lower version kernel, and it is a real.
You can see the patch history fro linux-exfat-oot.
this version support timezone and boot sector verification feature newly.
and better filesystem structure and much clean code quality that
reviewed by high profile kernel developers. and add many bug fixes.
And this version is officially maintained by me and kernel guys.
I would not recommend to use staging exfat version.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Enabling KERNEL_TRANSPARENT_HUGEPAGE exposes 2 missing symbols:
* CONFIG_READ_ONLY_THP_FOR_FS
* TRANSPARENT_HUGEPAGE_ALWAYS
* TRANSPARENT_HUGEPAGE_MADVISE
The first one was added in 5.4, and is marked experimental there so just
disable it in the generic config.
For the latter two, we should not force the user to use either of them,
so add them as build-configurable kernel options.
Fixes: d1a8217d87 ("kernel: clean-up build-configurable kernel config symbols")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This symbol is exposed on ARM64 with EFI enabled in the kernel config.
Currently this happens only on ipq807x, but as there might be new ARM64
targets with EFI in the future it is better to add the symbol to the
generic config.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Jo-Philipp Wich <jo@mein.io>
It was removed from target defaults though it didn't exist in the
build-systems kernel configuration options. Add it there.
Fixes: d1a8217d87 ("kernel: clean-up build-configurable kernel config symbols")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Don't kill the wireless daemon on teardown. hostapd as well as
wpa_supplicant are managed by procd which would detect the shutdown of
either process as a crash loop.
Signed-off-by: David Bauer <mail@david-bauer.net>
When retrieving the PID for hostapd and wpa_supplicant via ubus the
wrong service name is currently used. This leads to the following error
in the log:
netifd: radio0 (1409): WARNING (wireless_add_process):
executable path /usr/sbin/wpad does not match process path (/proc/exe)
Fixing the service name retrieves the correct PID and therefore the
warning won't occur.
Signed-off-by: David Bauer <mail@david-bauer.net>
Sometimes when using the DNS-313 memory usage can peak and
with a simple swap partition we can avoid running into the
roof and invoking the OOM killer. Set this partition to
128MB (twice the size of the memory of the DNS-313).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The compressed image that the buildbots are building is too large for
the netgear uboot and it crashes and soft-bricks the device.
| Uncompressing Kernel Image ...
| LZMA: uncompress or overwrite error 1 - must RESET board to recover
The whole target likely needs to be switched zImage which is a major
hassle due to powerpc's legacy bootwrapper setup as compared to ARM.
So for now, disable the device.
Reported-by: Wiktor Stasiak (FS#3258)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This replaces the internal device names "Audi" and "Viper" with the
real model names, which a user would look for. This makes the
Linksys devices on this target consistent with the names recently
changed for mvebu based on the same idea.
As a consequence, the "viper" device definition is split into two
separate definitions with the correct names for both real models.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Explicitly mount the BPF filesystem if available. This is used for pinning
eBPF programs and maps, making them accessible to other eBPF programs or
from userspace with the help of libbpf or bpftool.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
[daniel@makrotopia.org: bumped PKG_RELEASE]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kernel v5.1 included an eBPF JIT for MIPS32 kernels, but problems were
discovered [1] and the changes later reverted in kernel v5.5 with commits:
* f8fffebdea75 ("MIPS: BPF: Disable MIPS32 eBPF JIT")
* 36366e367ee9 ("MIPS: BPF: Restore MIPS32 cBPF JIT")
Only the first of these was backported to LTS kernel 5.4, leaving cBPF
programs without a JIT and introducing a performance regression for any
such users e.g. libpcap, tcpdump, etc.
Restore cBPF performance by backporting the second commit above:
* 070-v5.5-MIPS-BPF-Restore-MIPS32-cBPF-JIT.patch
[1] https://lore.kernel.org/bpf/20191205182318.2761605-1-paulburton@kernel.org/
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The current selection of DRIVER_MAKEOPTS and TARGET_LDFLAGS is
exceptionally hard to read. This tries to make things a little
easier by inverting the hierarchy of the conditions, so SSL_VARIANT
is checked first and LOCAL_VARIANT is checked second.
This exploits the fact that some of the previous conditions were
unnecessary, e.g. there is no hostapd-mesh*, so we don't need
to exclude this combination.
It also should make it a little easier to see which options are
actually switched by SSL_VARIANT and which by LOCAL_VARIANT.
The patch is supposed to be cosmetic.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
