Commit Graph

3489 Commits

Author SHA1 Message Date
Shiji Yang
1330816178 ramips: add support for H3C TX1800 Plus / TX1801 Plus / TX1806
H3C TX180x series WiFi6 routers are customized by different carrier.
While these three devices look different, they use the same motherboard
inside. Another minor difference comes from the model name definition
in the u-boot environment variable.

Specifications:
 SOC:      MT7621 + MT7915
 ROM:      128 MiB
 RAM:      256 MiB
 LED:      status *2
 Button:   reset *1 + wps/mesh *1
 Ethernet:        lan *3 + wan *1 (10/100/1000Mbps)
 TTL Baudrate:    115200
 TFTP server IP:  192.168.124.99

MAC Address:
 use        address(sample 1)   address(sample 2)    source
 label      88:xx:xx:98:xx:12   88:xx:xx:a2:xx:a5   u-boot-env@ethaddr
 lan        88:xx:xx:98:xx:13   88:xx:xx:a2:xx:a6   $label +1
 wan        88:xx:xx:98:xx:12   88:xx:xx:a2:xx:a5   $label
 WiFi4_2G   8a:xx:xx:58:xx:14   8a:xx:xx:52:xx:a7   (Compatibility mode)
 WiFi5_5G   8a:xx:xx:b8:xx:14   8a:xx:xx:b2:xx:a7   (Compatibility mode)
 WiFi6_2G   8a:xx:xx:18:xx:14   8a:xx:xx:12:xx:a7
 WiFi6_5G   8a:xx:xx:78:xx:14   8a:xx:xx:72:xx:a7

Compatibility mode is used to guarantee the connection of old devices
that only support WiFi4 or WiFi5.

TFTP + TTL Installation:
Although a TTL connection is required for installation, we do not need
to tear down it. We can find the TTL port from the cooling hole at the
bottom. It is located below LAN3 and the pins are defined as follows:
|LAN1|LAN2|LAN3|----|WAN|
--------------------
    |GND|TX|RX|VCC|

1. Set tftp server IP to 192.168.124.99 and put initramfs firmware in
   server's root directory, rename it to a simple name "initramfs.bin".
2. Plug in the power supply and wait for power on, connect the TTL cable
   and open a TTL session, enter "reboot", then enter "Y" to confirm.
   Finally push "0" to interruput boot while booting.
3. Execute command to install a initramfs system:
   # tftp 0x80010000 192.168.124.99:initramfs.bin
   # bootm 0x80010000
4. Backup nand flash by OpenWrt LuCI or dd instruction. We need those
   partitions if we want to back to stock firmwre due to official
   website does not provide download link.
   # dd if=/dev/mtd1 of=/tmp/u-boot-env.bin
   # dd if=/dev/mtd4 of=/tmp/firmware.bin
5. Edit u-boot env to ensure use default bootargs and first image slot:
   # fw_setenv bootargs
   # fw_setenv bootflag 0
6. Upgrade sysupgrade firmware.
7. About restore stock firmware: flash the "firmware" and "u-boot-env"
   partitions that we backed up in step 4.
   # mtd write /tmp/u-boot-env.bin u-boot-env
   # mtd write /tmp/firmware.bin firmware

Additional Info:
The H3C stock firmware has a 160-byte firmware header that appears to
use a non-standard CRC32 verification algorithm. For this part of the
data, the u-boot does not check it so we can just directly replace it
with a placeholder.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-07-31 19:23:24 +02:00
John Audia
7be62b1187 kernel: bump 5.10 to 5.10.134
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-07-29 23:03:41 +02:00
David Bauer
a0b7fef0ff ramips: add support for ZyXEL NWA50AX / NWA55AXE
Hardware
--------
CPU:    Mediatek MT7621
RAM:    256M DDR3
FLASH:  128M NAND
ETH:    1x Gigabit Ethernet
WiFi:   Mediatek MT7915 (2.4/5GHz 802.11ax 2x2 DBDC)
BTN:    1x Reset (NWA50AX only)
LED:    1x Multi-Color (NWA50AX only)

UART Console
------------
NWA50AX:
Available below the rubber cover next to the ethernet port.
NWA55AXE:
Available on the board when disassembling the device.

Settings: 115200 8N1

Layout:

<12V> <LAN> GND-RX-TX-VCC

Logic-Level is 3V3. Don't connect VCC to your UART adapter!

Installation Web-UI
-------------------
Upload the Factory image using the devices Web-Interface.

As the device uses a dual-image partition layout, OpenWrt can only
installed on Slot A. This requires the current active image prior
flashing the device to be on Slot B.

If the currently installed image is started from Slot A, the device will
flash OpenWrt to Slot B. OpenWrt will panic upon first boot in this case
and the device will return to the ZyXEL firmware upon next boot.

If this happens, first install a ZyXEL firmware upgrade of any version
and install OpenWrt after that.

Installation TFTP
-----------------
This installation routine is especially useful in case
 * unknown device password (NWA55AXE lacks reset button)
 * bricked device

Attach to the UART console header of the device. Interrupt the boot
procedure by pressing Enter.

The bootloader has a reduced command-set available from CLI, but more
commands can be executed by abusing the atns command.

Boot a OpenWrt initramfs image available on a TFTP server at
192.168.1.66. Rename the image to owrt.bin

 $ atnf owrt.bin
 $ atna 192.168.1.88
 $ atns "192.168.1.66; tftpboot; bootm"

Upon booting, set the booted image to the correct slot:

 $ zyxel-bootconfig /dev/mtd10 get-status
 $ zyxel-bootconfig /dev/mtd10 set-image-status 0 valid
 $ zyxel-bootconfig /dev/mtd10 set-active-image 0

Copy the OpenWrt ramboot-factory image to the device using scp.
Write the factory image to NAND and reboot the device.

 $ mtd write ramboot-factory.bin firmware
 $ reboot

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-07-20 21:52:06 +02:00
Wenli Looi
0f068e7c4a
ramips: add support for Netgear WAX202
Netgear WAX202 is an 802.11ax (Wi-Fi 6) router.

Specifications:
* SoC: MT7621A
* RAM: 512 MiB NT5CC256M16ER-EK
* Flash: NAND 128 MiB F59L1G81MB-25T
* Wi-Fi:
  * MT7915D: 2.4/5 GHz (DBDC)
* Ethernet: 4x 1GbE
  * Switch: SoC built-in
* USB: None
* UART: 115200 baud (labeled on board)

Load addresses (same as ipTIME AX2004M):
* stock
  * 0x80010000: FIT image
  * 0x81001000: kernel image -> entry
* OpenWrt
  * 0x80010000: FIT image
  * 0x82000000: uncompressed kernel+relocate image
  * 0x80001000: relocated kernel image -> entry

Installation:
* Flash the factory image through the stock web interface, or TFTP to
  the bootloader. NMRP can be used to TFTP without opening the case.
* Note that the bootloader accepts both encrypted and unencrypted
  images, while the stock web interface only accepts encrypted ones.

Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.

References in WAX202 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX202_V1.0.5.1_Source.rar

* openwrt/target/linux/ramips/dts/mt7621-ax-nand-wax202.dts
  DTS file for this device.

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2022-07-19 14:49:04 +02:00
Rui Salvaterra
3e9ad2cdce kernel: bump 5.15 to 5.15.53
Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-07-11 00:50:18 +02:00
Nita Vesa
1a8c74da70 ramips: Add Xiaomi Mi Router 4A 100M International
The international version of Mi Router 4A 100M is physically
identical to the non-international one, but appears to be
using a different partitioning scheme with the "overlay"
partition being 2MiB in size instead of 1MiB. This means
the following "firmware" partition starts at a different
address and the DTS needs to be adjusted for the firmware
to work.

Signed-off-by: Nita Vesa <werecatf@outlook.com>
2022-07-03 22:14:05 +02:00
Sergei Iudin
4b0c433c39 ramips: Add suport for COMFAST CF-WR617AC
Specifications:
Chipset:MT7628DA+MT7612E
Antenna : 2.4Ghz:2x5dbi Antenna + 5.8Ghz:2x5dbi Antenna
Wireless Rate:2.4Ghz 300Mbps , 5.8Ghz 867Mbps
Output Power :100mW(20dbm)
Physical port:110/100Mbps RJ45 WAN Port , 310/100Mbps RJ45 LAN Port
Flash: 8Mb
DRam: 64Mb
Flashing: default bootloader attempts to boot from tftp://192.168.1.10/firmware_auto.bin using 192.168.1.1

Known issues:
mac-address-increment for 5GHZ doesnt work, i failed to figure out why. Original firmware using +1 from original value in factory partition.

Signed-off-by: Sergei Iudin <tsipa740@gmail.com>
2022-07-03 22:14:05 +02:00
Mikhail Zhilkin
bd783fd60a ramips: add support for Beeline SmartBox GIGA
Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by
Sercomm company.

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB, Nanya NT5CC128M16JR-EK
Flash: 128 MiB, Macronix MX30LF1G18AC
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7613BE): a/n/ac, 2x2
Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2)
USB ports: 1xUSB3.0
Button: 1 button (Reset/WPS)
PCB ID: DBE00B-1.6MM
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot

Installation
-----------------
1. Downgrade stock (Beeline) firmware to v.1.0.02;
2. Give factory OpenWrt image a shorter name, e.g. 1001.img;
3. Upload and update the firmware via the original web interface.

Remark: You might need make the 3rd step twice if your running firmware
is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware
reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update.

Revert to stock
---------------
1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
      printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
2. Optional: Update with any stock (Beeline) firmware if you want to
   overwrite OpenWrt in Slot 0 completely.

MAC Addresses
-------------
+-----+-----------+---------+
| use | address   | example |
+-----+-----------+---------+
| LAN | label     | *:16    |
| WAN | label + 1 | *:17    |
| 2g  | label + 4 | *:1a    |
| 5g  | label + 5 | *:1b    |
+-----+-----------+---------+
The label MAC address was found in Factory 0x21000

Notes
-----
1. The following scripts are required for the build:
      sercomm-crypto.py - already exists in OpenWrt
      sercomm-partition-tag.py - already exists in OpenWrt
      sercomm-payload.py - already exists in OpenWrt
      sercomm-pid.py - new, the part of this pull request
      sercomm-kernel-header.py - new, the part of this pull request
2. This device (same as other Sercomm S2,S3-based devices) requires
   special LZMA and LOADADDR settings for successful boot:
      LZMA_TEXT_START=0x82800000
      KERNEL_LOADADDR=0x81001000
      LOADADDR=0x80001000
3. This device (same as several other Sercomm-based devices - Beeline,
   Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing
   real partition offsets, which may differ from device to device
   depending on the number and location of bad blocks on NAND.
   "fixed-partitions" is used if the partition map is not found or
   corrupted. This behavour (it's the same as on stock firmware) is
   provided by MTD_SERCOMM_PARTS module.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-07-03 20:25:38 +02:00
Rui Salvaterra
90a6350423 kernel: bump 5.15 to 5.15.50
Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-07-03 20:25:38 +02:00
Thibaut VARÈNE
a0e1d3ab7b
ramips: improve YunCore AX820 LEDs
At least two AX820 hardware variants are known to exist, but they cannot
be distinguished (same hardware revision, no specific markings).

They appear to have the same LED hardware, but wired differently:

- One has a red system LED at GPIO 15, a green wlan2g LED at GPIO 14 and
  a blue wlan5g LED at GPIO 16;
- The other only offers a green system LED at GPIO 15, with GPIO 14 and
  16 being apparently not connected

Finally, a Yuncore datasheet says the canonical wiring should be:
- Blue wlan2g GPIO 14, green system GPIO 15, red wlan5g GPIO 16

All GPIOs are tied to a single RGB LED which is exposed via lightpipe on
the device front casing.

Considering the above, this patch exposes all three LEDs, preserves the
common system LED (GPIO 15) as the openwrt status LED, and removes the
color information from the LEDs names since it is not consistent across
hardware. The LED naming is made consistent with other YunCore devices.
A note is added in DTS to ensure this information is always available
and prevent unwanted changes in the future.

Fixes: #10131 "YunCore AX820: GPIO LED not correct"

Reviewed-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2022-07-01 20:13:46 +02:00
John Thomson
ef69ab7a35 kernel: cut broken SPI_NOR 4K eraseblock LIMIT patch
Since 4e0c54bc5b ("kernel: add support for kernel 5.4"),
the spi-nor limit 4k erasesize to spi-nor chips below a configured size
patch has not functioned as intended.

For uniform erasesize SPI-NOR devices, both
nor->erase_opcode & mtd->erasesize are used in erase operations.
These are set before, and not modified by, this
CONFIG_MTD_SPI_NOR_USE_4K_SECTORS_LIMIT patch.
Thus, an SPI-NOR device with CONFIG_MTD_SPI_NOR_USE_4K_SECTORS will
always use 4k erasesize (where the device supports it).

If this patch was fixed to function as intended, there would be
cases where devices change from a 4K to a 64K erasesize.

Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
2022-06-29 12:34:49 +02:00
Tamas Balogh
74dd7f9c36 ramips: add support for ASUS RP-AC87
Asus RP-AC87 ac2600 Repeater
2.4GHz 800Mbps
5GHz 1733Mbps

Hardware specifications:
SoC: MT7621A 2 cores 4 threads @880MHz
WiFi2G: MT7615E 2G 4x4 b/g/n
Wifi5G: MT7615E 5G 4x4 n/ac
DRAM: 128MB DDR3 @1200mhz
Flash: 16MB MX25L12805D SPI-NOR
LAN/WAN: MT7530 1x1000M

MAC addresses as verified by OEM firmware:
use address source
Lan/W5G *:B0 factory 0x8004 (label)
W2G *:B4 factory 0x0

Installation:

Asus windows recovery tool:

install the Asus firmware restoration utility
unplug the router, hold the reset button while powering it on
release when the power LED flashes slowly
specify a static IP on your computer:
IP address: 192.168.1.75
Subnet mask 255.255.255.0
Start the Asus firmware restoration utility, specify the factory image
and press upload
Do not power off the device after OpenWrt has booted until the LED flashing.
TFTP Recovery method:

set computer to a static ip, 192.168.1.2
connect computer to the LAN 1 port of the router
hold the reset button while powering on the router for a few seconds
send firmware image using a tftp client; i.e from linux:
$ tftp
tftp> binary
tftp> connect 192.168.1.1
tftp> put factory.bin
tftp> quit

Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
2022-06-29 00:57:56 +02:00
Rui Salvaterra
b55efebb1f kernel: bump 5.15 to 5.15.47
Deleted (upstreamed):
generic/backport-5.15/702-v5.19-32-net-ethernet-mtk_eth_soc-out-of-bounds-read-in-mtk_h.patch [01]

[01] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.47&id=b24ca1cf846273361d5bd73a35de95a486a54b6d

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[Removed 702-v5.19-32-net-ethernet-mtk_eth_soc-out-of-bounds-read-in-mtk_h.patch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-06-27 00:57:16 +02:00
Rui Salvaterra
251a382c28 kernel: bump 5.15 to 5.15.46
Deleted (upstreamed):
generic/backport-5.15/400-mtdblock-warn-if-opened-on-NAND.patch [01]
generic/backport-5.15/420-v5.19-01-mtd-spinand-gigadevice-fix-Quad-IO-for-GD5F1GQ5UExxG.patch [02]
bcm27xx/patches-5.15/950-0029-Revert-mailbox-avoid-timer-start-from-callback.patch [03]
bcm27xx/patches-5.15/950-0417-bcm2711_thermal-Don-t-clamp-temperature-at-zero.patch [04]
bcm27xx/patches-5.15/950-0740-drm-vc4-hvs-Fix-frame-count-register-readout.patch [05]
bcm27xx/patches-5.15/950-0755-drm-vc4-hvs-Reset-muxes-at-probe-time.patch [06]
bcm27xx/patches-5.15/950-0759-drm-vc4-txp-Don-t-set-TXP_VSTART_AT_EOF.patch [07]
bcm27xx/patches-5.15/950-0760-drm-vc4-txp-Force-alpha-to-be-0xff-if-it-s-disabled.patch [08]
bcm53xx/patches-5.15/031-v5.17-0005-ARM-dts-BCM5301X-update-CRU-block-description.patch [09]
mediatek/patches-5.15/102-mt7629-enable-arch-timer.patch [10]

Manually rebased:
bcm27xx/patches-5.15/950-0741-drm-vc4-hvs-Use-pointer-to-HVS-in-HVS_READ-and-HVS_W.patch

[01] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=f41c9418c5898c01634675150696da290fb86796
[02] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=d5b66645305c6f3a1b2cf75cee4157b07f293309
[03] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=119f99209d8531359bcb935f252ec435f9d21b13
[04] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=c4e1280abead1552e1764684079a43e222ccd163
[05] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=08465a1889cb48ec64431e9db745b5be15399251
[06] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=0e26a6da02e63b75b629573d13966c36aa6264f0
[07] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=01c9020b2e7c85e394879f34851805179ac3d1d8
[08] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=d47f85cc0171a5d3c5bd8cbb8a98983ca3357cbd
[09] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=5151f24ac937ff7eb1f078257c66e3c0f0296010
[10] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=ffea838686b82fbb2801cdfad6ba5309d15c032d

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-06-27 00:57:16 +02:00
John Audia
53d99fedc7 kernel: bump 5.10 to 5.10.125
All patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-06-27 00:57:16 +02:00
John Audia
9e5d743422 kernel: bump 5.10 to 5.10.124
All patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-06-27 00:57:15 +02:00
John Audia
9edc514e3d kernel: bump 5.10 to 5.10.122
All patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-06-27 00:57:15 +02:00
John Audia
706a4ec40c kernel: bump 5.10 to 5.10.121
Manually rebased:
    oxnas/patches-5.10/100-oxnas-clk-plla-pllb.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-06-27 00:57:15 +02:00
Semih Baskan
530c0a2068 ramips: add support for Asus RT-N12+ B1 and RT-N300 B1
Asus RT-N12+ B1 and Asus RT-N300 B1 are the same device
with a different name.

The OEM firmwares have the same MD5 with Asus RT-N11P B1.

Same instructions for Asus RT-N11P B1 see:
commit c3dc52e39a ("ramips: add support for Asus RT-N10P V3 / RT-N11P B1 / RT-N12 VP B1")

Signed-off-by: Semih Baskan <strstgs@gmail.com>
(Added id from the PR review to commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-06-25 10:14:18 +02:00
Chuncheng Chen
8c00fd9b45 ramips: add support for ASUS RT-AX53U
Specifications:
- Device: ASUS RT-AX53U
- SoC: MT7621AT
- Flash: 128MB
- RAM: 256MB
- Switch: 1 WAN, 3 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- Ports: USB 3.0
- LEDs: 1x POWER (blue, configurable)
        3x LAN (blue, configurable)
        1x WAN (blue, configurable)
        1x USB (blue, not configurable)
	1x 2.4G (blue, not configurable)
	1x 5G (blue, not configurable)

Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.1.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
   Select "2. Upgrade firmware"
   Press enter when show "Run firmware after upgrading? (Y/n):"
   Select 0 for TFTP method
   Input U-Boot's IP address: 192.168.1.1
   Input TFTP server's IP address: 192.168.1.2
   Input IP netmask: 255.255.255.0
   Input file name: openwrt-ramips-mt7621-asus_rt-ax53u-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"

Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com>
(replaced led label, added key-* prefix to buttons, added note about
BBT)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-06-25 10:14:18 +02:00
Tomasz Maciej Nowak
539e60539a generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]
This is now built-in, enable so it won't propagate on target configs.

Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca9367069 ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-06-24 17:10:24 +02:00
Bjørn Mork
79112e7d47 ramips: force ZyXEL NR7101 to boot from "Kernel" partition
Make sure BootingFlag points to the system partition we install to.

The BootingFlag variable selects which system partition the system
boots from (0 => "Kernel", 1 => "Kernel2"). OpenWrt does not yet have
device specific support for this dual image scheme, and can therefore
only boot from "Kernel".

This has not been an issue until now, since all known OEM firmware
versions have ignored "Kernel2" - leaving the BootingFlag fixed at 0.
But the newest OEM firmware has a new upgrade procedure, installing
to the "inactive" system partition and setting BootingFlag accordingly.

This workaround is needed until the dual image scheme is fully
supported.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2022-06-24 09:18:03 +02:00
Arınç ÜNAL
a1ad837735 ramips: mt7621-dts: fix claiming rgmii2 pin group for EdgeRouter X SFP
For a TX->TX connected external phy to transmit/receive data, the rgmii2
pin group needs to be claimed with gpio function, at least for EdgeRouter X
SFP. We already claim the pin group under the pinctrl node with gpio
function on the gpio node on mt7621_ubnt_edgerouter-x.dtsi.

However, we should claim a pin group under its consumer node. It's the
ethernet node in this case, which we already claim the rgmii2 pin group
under it on mt7621.dtsi. Therefore, set the function as gpio on the rgmii2
node for EdgeRouter X SFP and get rid of claiming the rgmii2 pin group
under the pinctrl node. With this change, we also get to remove a
definition from mt7621_ubnt_edgerouter-x.dtsi which is specific to
EdgeRouter X SFP.

This change is tested on an EdgeRouter X SFP.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2022-06-24 09:18:03 +02:00
Piotr Dymacz
fd72e595c2 ramips: fix booting on ZyXEL NBG-419N v2
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of other devices from 'ramips' target.

Fixes: #9842
Fixes: #8964

Reported-by: Juergen Hench <jurgen.hench@gmail.com>
Tested-by: Juergen Hench <jurgen.hench@gmail.com>
Signed-off-by: Demetris Ierokipides <ierokipides.dem@gmail.com>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2022-06-20 11:05:41 +02:00
David Bauer
535b0c70b1 ramips: fix RT-AC57U button level
Both buttons on the RT-AC57U are active-low. Fix the GPIO flag for the
WPS cutton to fix button behavior.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-06-18 22:11:19 +02:00
Mikhail Zhilkin
498c15376b ramips: add support for MTS WG430223
MTS WG430223 is a wireless AC1300 (WiFi 5) router manufactured by
Arcadyan company. It's very similar to Beeline Smartbox Flash (Arcadyan
WG443223).

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB
Flash: 128 MiB (Winbond W29N01HV)
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: No
Button: 1 (Reset/WPS)
LEDs: 2 (Red, Green)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WG430223

Installation
------------
1. Login to the router web interface (superadmin:serial number)
2. Navigate to Administration -> Miscellaneous -> Access control lists &
   enable telnet & enable "Remote control from any IP address"
3. Connect to the router using telnet (default admin:admin)
4. Place *factory.trx on any web server (192.168.1.2 in this example)
5. Connect to the router using telnet shell (no password required)
6. Save MAC adresses to U-Boot environment:
   uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
    awk '{print $5}')
   uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
    awk '{print $5}')
   uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
    awk '{print $5}')
   uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
    awk '{print $5}')
7. Ensure that MACs were saved correctly:
   uboot_env --get --name eth2macaddr
   uboot_env --get --name eth3macaddr
   uboot_env --get --name ra0macaddr
   uboot_env --get --name rax0macaddr
8. Download and write the OpenWrt images:
   cd /tmp
   wget http://192.168.1.2/factory.trx
   mtd_write erase /dev/mtd4
   mtd_write write factory.trx /dev/mtd4
9. Set 1st boot partition and reboot:
   uboot_env --set --name bootpartition --value 0

Back to Stock
-------------
1. Run in the OpenWrt shell:
   fw_setenv bootpartition 1
   reboot
2. Optional step. Upgrade the stock firmware with any version to
   overwrite the OpenWrt in Slot 1.

MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC               | Source         |
+-----------+-------------------+----------------+
| label     | A4:xx:xx:51:xx:F4 | No MACs was    |
| LAN       | A4:xx:xx:51:xx:F6 | found on Flash |
| WAN       | A4:xx:xx:51:xx:F4 | [1]            |
| WLAN_2g   | A4:xx:xx:51:xx:F5 |                |
| WLAN_5g   | A6:xx:xx:21:xx:F5 |                |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
   key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
   with saving of the MACs to u-boot-env during the installation was
   applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:A0) was found in
   "Factory" 0xfff0. It's the same for all MTS WG430223 devices. OEM
   firmware also uses this MAC when initialazes ethernet driver. In
   OpenWrt we use it only as internal GMAC (eth0), all other MACs are
   unique. Therefore, there is no any barriers to the operation of several
   MTS WG430223 devices even within the same broadcast domain.

Stock firmware image format
---------------------------
The same as Beeline Smartbox Flash but with another trx magic
+--------------+---------------+----------------------------------------+
| Offset       |               | Description                            |
+==============+===============+========================================+
| 0x0          | 31 52 48 53   | TRX magic "1RHS"                       |
+--------------+---------------+----------------------------------------+

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-06-13 15:26:23 +08:00
Mikhail Zhilkin
5b59137a16 ramips: create new dtsi for Arcadyan routers
This commit moves common properties for the boards below to a new dtsi:
Beeline Smartbox Flash (Arcadyan WG443223)
MTS WG430223 (Arcadyan WG430223)

The boards are almost the same. Here is the differences:
+------+----------+----------+
|      | WG430223 | WG443223 |
+------+----------+----------+
| RAM  | 128      | 256      |
+------+----------+----------+
| USB  | -        | 1x3.0    |
+------+----------+----------+
| LEDS | RG       | RGB      |
+------+----------+----------+

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-06-13 15:26:23 +08:00
Mikhail Zhilkin
109c503bee ramips: allow custom trx magic for Arcadyan
This commit:
1. Renames beeline-trx recipe in mt7621.mk to arcadyan-trx. The recipe
   is necessary for:
   - MTS WG430223 (Arcadyan WG430223)
   - Beeline Smartbox Flash (Arcadyan WG443223)
2. Allows specify custom trx magic which is different for the routers
   mentined above.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-06-13 15:26:23 +08:00
Aviana Cruz
857ea3f690 ramips: decrease SPI frequency for Phicomm K2P
Some K2P comes with the worse boards with GD25Q128 (may be A2), which
only works with 50MHz frequency and less. Reduce spi frequency so that
these routers can boot.
remove m25p,fast-read because it isn't needed for 50MHz SPI.

Signed-off-by: Aviana Cruz <gwencroft@proton.me>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-06-13 15:26:23 +08:00
Rui Salvaterra
ed1536e0b6 kernel: bump 5.15 to 5.15.41
Deleted (upstreamed):
generic/backport-5.15/890-v5.19-net-sfp-Add-tx-fault-workaround-for-Huawei-MA5671A-SFP-ON.patch [1]

Other patches automatically rebased.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.41&id=99858114a3b2c8f5f8707d9bbd46c50f547c87c0

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-06-06 19:20:28 +02:00
John Audia
01a6a5c731 kernel: bump 5.10 to 5.10.117
Removed upstreamed:
    backport-5.10/890-v5.19-net-sfp-Add-tx-fault-workaround-for-Huawei-MA5671A-SFP-ON.patch

All patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-06-06 19:20:02 +02:00
Stijn Tintel
ce90ba1f31 ramips: use hotplug script for EAP615-Wall MACs
Using nvmem-cells to set the MAC address for a DBDC device results in
both PHY devices using the same MAC address. This in turn will result in
multiple BSSes using the same BSSID, which can cause various problems.

Use the hotplug script for the EAP615-Wall instead to avoid this.

Fixes: a1b8a4d7b3 ("ramips: support TP-Link EAP615-Wall")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-By: Andrew Powers-Holmes <aholmes@omnom.net>
2022-06-03 13:45:38 +03:00
David Bauer
275a76e59a ramips: disable unsupported background-radar
The UniFi 6 Lite as well as the Tenbay T-MB5EU do not have the third
background-radar chain. For the Tenbay, the connector is present,
however no antenna is connected to it.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-05-29 00:00:39 +02:00
Andreas Böhler
9ee6ac00c4 ramips: Add support for SERCOMM NA502S
The SERCOMM NA502s is a smart home gateway manufactured by SERCOMM and sold
under different brands (among others, A1 Telekom Austria SmartHome Premium
Gateway). It has multi-protocol radio support in addition to LAN and WiFi.

Note: BLE and audio are currently unsupported.

Specifications
--------------

  - MT7621ST 880MHz, Single-Core, Dual-Thread
  - MT7603EN 2.4GHz WiFi
  - MT7662EN 5GHz WiFi + BLE
  - 128MiB NAND
  - 256MiB DDR3 RAM
  - SD3503 ZWave Controller
  - EM357 Zigbee Coordinator
  - Telit UMTS module
  - Rechargeable battery
  - speaker and microphone

MAC address assignment
----------------------

LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches
the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the
OEM firmware does not enable 5GHz WiFi.

Installation
------------
Attach serial console, then boot the initramfs image via TFTP.
Once inside OpenWrt, run sysupgrade -n with the sysupgrade file.

Attention: The device has a dual-firmware design. We overwrite kernel2,
since kernel1 contains an automatic recovery image.

If you get NAND ECC errors and are stuck with bad eraseblocks, try to
erase the mtd partition first with

mtd unlock ubi
mtd erase ubi

This should only be needed once.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2022-05-16 20:26:38 +02:00
Tamas Balogh
771ea6f2e3 ramips: add led_source for Asus RT-AC1200 devices
this adds the mediatek,led_source dts binding for
Asus RT-AC1200 devices' dtsi, for correct switch LED
behavior.

The dts-binding is introduced in commit:
65dc9e0980

Without this, we only have constantly very fast
blinking LEDs, which don't react on any traffic or
LAN events at all.

Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
2022-05-15 22:59:35 +02:00
Piotr Dymacz
064e7e57b4 ramips: fix booting on Samknows SK-WB8
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.

Fixes: #9824
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2022-05-13 13:43:32 +02:00
Rui Salvaterra
c3569a70c6 kernel: bump 5.15 to 5.15.36
Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-05-09 20:49:50 +01:00
Alessio Prescenzo
4a8eaa5c7c ramips: add support for Cudy X6
Specifications:

SoC: MediaTek MT7621
RAM: 256 MB
Flash: 32 MB
WiFi: MediaTek MT7915E
Switch: 1 WAN, 4 LAN (Gigabit)
Ports: 1 USB 3.0
Buttons: Reset, WPS
LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
Power: DC 12V 1A tip positive
Installation:

Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.

Recovery:

Loads only signed manufacture firmware due to bootloader RSA verification
serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
connect to any lan ethernet port
power on the device while holding the reset button
wait at least 8 seconds before releasing reset button for image to
download

Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com>
[ensure unique wireless MAC, fix GPIO pingroup]
Signed-off-by: David Bauer <mail@david-bauer.net>
2022-05-09 15:31:01 +02:00
Ptilopsis Leucotis
b697b5c55e ramips: add i2c in dts for GL-MT300N-V2
According wiki https://docs.gl-inet.com/en/2/hardware/mt300n-v2/
GL-MT300N-V2 have I2C interface on GPIO4, GPIO5.
Adding I2C in device tree make possible using I2C on this device.

Signed-off-by: Ptilopsis Leucotis <PtilopsisLeucotis@yandex.com>
2022-05-05 09:19:00 +09:00
Tamas Balogh
65dc9e0980 ramips: ethernet: ralink: add led_source dts-binding
this adds the new dts-binding "mediatek,led_source"
currently for MT7628AN and MT7688 built-in switches,
which is documented as a 3-bit field configuring the
switch LEDs for various control schemes from 0 to 3.

Normally this is not needed, but e.g. for Asus RT-AC1200-V2
it is a must to set it to the anyway undocumented value
of 4, to have the switch LEDs react correctly on link/act
events. This is an MT7628DAN device, but I doubt this is
a speciality of this particular SoC.

Also added the RT305X_ESW_LED_OFF value to LED states.
Did also rename the register RT5350_EWS_REG_LED_POLARITY
to RT5350_EWS_REG_LED_CONTROL, which is the correct name.
Also making use of defines for some hardcoded values.

Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
2022-05-01 13:40:13 +09:00
Alban Bedel
d806c3caf3 ramips: zbt-wg2626: Fix the LAN ports names
The current names don't match with the labels on the case, reverse
the LAN ports order so they match.

Signed-off-by: Alban Bedel <albeu@free.fr>
2022-05-01 13:39:56 +09:00
Alban Bedel
f953a1a4bf ramips: zbt-wg2626: Add the reset gpio for PCIe port 1
The 2.4GHz interface doesn't come up properly with the log showing:

    mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)

As seen on other MT7621 boards this is caused by a missing reset GPIO.
The MT7621 dtsi set GPIO 19 as PCIe reset GPIO, which on this board
reset the 5GHz interface on port 0. Add GPIO 8 to the PCIe reset GPIO
list to also reset the 2.4GHz interface on port 1.

Signed-off-by: Alban Bedel <albeu@free.fr>
2022-05-01 11:21:23 +08:00
Davide Fioravanti
32e6942d72 ramips: add support for Wavlink WL-WN533A8
The Wavlink WL-WN533A8 is an AC3000 router with 5 gigabit ethernet ports
and one USB 3.0 port.
It's also known as Wavlink QUANTUM T8.

Hardware
--------
SoC:   Mediatek MT7621A
RAM:   128MB (Nanya NT5CB64M16GP-EK)
FLASH: 16MB NOR (GigaDevice GD25Q127CSIG3)
ETH:
  - 5x 10/100/1000 Mbps Ethernet (4x LAN + 1x WAN)
WIFI:
  - 1x MT7615DN (2x 2x2:2) 2.4GHz and 5GHz DBDC
  - 1x MT7615NE (4x4:4) 5GHz
  - 8 external antennas
BTN:
  - 1x Reset button
  - 1x WPS button
  - 1x Turbo button
  - 1x Touchlink button
  - 1x ON/OFF switch
LEDS:
  - 1x Red led (system status)
  - 1x Blue led (system status)
  - 7x Blue leds (wifi led + 5 ethernet ports + power)
USB:
  - 1x USB 3.0 port
UART:
  - 57600-8-N-1
    J4

Everything works correctly.

Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
(Procedure tested on fw M33A8.V5030.190716 and M33A8.V5030.201204)

Restore OEM Firmware
--------------------
Flash the firmware update available online directly from LUCI.
You can download it from:
https://www.wavlink.com/en_us/firmware/details/f2d247ecba.html
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Notes
-----
1) Router mac addresses:
   LAN		XX:XX:XX:XX:XX:63 (factory @ 0xe006)
   WAN		XX:XX:XX:XX:XX:64 (factory @ 0xe000)
   WIFI 2G/5G	XX:XX:XX:XX:XX:65 (factory @ 0x04)
   WIFI 5G	XX:XX:XX:XX:XX:66 (factory @ 0x8004)

   LABEL	XX:XX:XX:XX:XX:65

   In OEM firmware the DBDC wifi interfaces have these mac addresses:
     2G) 82:XX:XX:XX:XX:65
     5G) 80:XX:XX:XX:XX:65

   While in OpenWrt the addresses are:
     2G) 80:XX:XX:XX:XX:65
     5G) 02:XX:XX:XX:XX:65

2) radio0 will show as 2G/5G interface but only 2G is really usable.

3) There is just one wifi led for all wifi interfaces.
   It currently shows only the radio0 GHz wifi activity.

4) My unit was shipped with M33A8.V5030.190716 firmware which contains
   the http://192.168.10.1/webcmd.shtml page. Entering "telnetd" in
   the input box it will start the telnet daemon. Now you can access
   the telnet console on port 2323 with these credentials:
     username: admin2860
     password: admin

5) The M33A8.V5030.201204 firmware version, doesn't contain anymore the
   webcmd.shtml page. If your router is shipped with a previous firmware
   version and you want to back it up, you can follow the back up
   procedure of the WS-WN583A6.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2022-04-30 23:56:47 +02:00
Davide Fioravanti
57b6dcd826 ramips: create shared DTSI for Wavlink WN53XAX devices
Most of the definitions for WN531A6 will be shared with WN533A8 in a
future commit, so put them in a shared DTSI.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2022-04-30 23:56:47 +02:00
Marcin Gordziejewski
39799974a3 ramips: add support for TP-Link RE650 v2
TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1

Hardware specification:

- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
  requires soldering because they're not through holes.

  Serial console @ 57600,8n1

Flash instructions:

Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.

TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.

Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
2022-04-23 22:02:27 +02:00
Clemens Hopfer
4891b86538 ramips: add support for YunCore AX820/HWAP-AX820
There are two versions which are identical apart from the enclosure:
  YunCore AX820: indoor ceiling mount AP with integrated antennas
  YunCore HWAP-AX820: outdoor enclosure with external (N) connectors

Hardware specs:
  SoC: MediaTek MT7621DAT
  Flash: 16 MiB SPI NOR
  RAM: 128MiB (DDR3, integrated)
  WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax
  Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN)
  LED: Status (green)
  Button: Reset
  Power: 802.11af/at PoE; DC 12V,1A
  Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external

Flash instructions:
  The "OpenWRT support" version of the AX820 comes with a LEDE-based
  firmware with proprietary MTK drivers and a luci webinterface and
  ssh accessible under 192.168.1.1 on LAN; user root, no password.
  The sysupgrade.bin can be flashed using luci or sysupgrade via ssh,
  you will have to force the upgrade due to a different factory name.
  Remember: Do *not* preserve factory configuration!

MAC addresses as used by OEM firmware:
  use   address            source
  2g    44:D1:FA:*:0b      Factory 0x0004 (label)
  5g    46:D1:FA:*:0b      LAA of 2g
  lan   44:D1:FA:*:0c      Factory 0xe000
  wan   44:D1:FA:*:0d      Factory 0xe000 + 1
The wan MAC can also be found in 0xe006 but is not used by OEM dtb.

Due to different MAC handling in mt76 the LAA derived from lan is used
for 2g to prevent duplicate MACs when creating multiple interfaces.

Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
2022-04-23 20:46:25 +02:00
Ray Wang
9a750aae62 ramips: add support for OrayBox X3A
OrayBox X3A is a 2.4/5GHz dual band AC router, based on MediaTek MT7621.

Specification:
* SoC: MT7621
* RAM: DDR3 128 MiB
* Flash: 16 MiB NOR (XM25Q128)
* Wi-Fi: (single chip hosting both 2.4G and 5G)
  * 2.4GHz: MT7615
  * 5GHz: MT7615
* Ethernet: 3x 1000Mbps
  * Switch: MT7530
* LED:
  * Ethernet LEDs: On the back of the router, hardware-controlled.
  * Status LEDs: One "pixel-like" RGB LED in the front of the router,
                 which is actually made up of 3 individual LEDs (with
                 dedicated GPIO pins) with the color of Red, Green,
                 and Blue.
                 The OEM firmware only lights up one color at a time to
                 indicate status, but that's very boring, and the colors
                 actually look great when combined, so I've improvised a
                 little and made them indicate netdev activities.
                 My test results:
                 GPIO 13/14/15
                 000 white (actually more like bright green or cyan
                            because the brightness of the green LED is
                            higher than red and blue)
                 001 bright purple
                 010 bright green
                 011 red
                 100 bright cyan
                 101 blue
                 110 green
                 111 off

Flash Layout:
 0x0000000-0x0030000 : "u-boot"
 0x0030000-0x0040000 : "u-boot-env"
 0x0040000-0x0050000 : "factory"
 0x0050000-0x0f50000 : "firmware"
 /*0x0f50000 to 0x0fe0000 is undefined, same as OEM firmware*/
 0x0fe0000-0x0ff0000 : "bdinfo"
 0x0ff0000-0x1000000 : "reserve"

MAC address:
 MAC               Source                          Description    Fix
 A0:CX:XX:BX:XX:0D BDINFO_9                        LAN(LABEL)     DTS
 A0:CX:XX:BX:XX:0E BDINFO_9 + 1                    WAN            DTS
 A2:CX:XX:BX:XX:0F FACTORY_4                       WIFI2G         DTS
 A2:CX:XX:CX:XX:0F SETBIT 7 (FACTORY_4 + 0x100000) WIFI5G         HOTPLUG
 A6:CX:XX:BX:XX:0F N/A                             WIFI2G_CLIENT  N/A
 A6:DX:XX:BX:XX:0F N/A                             WIFI5G_CLIENT  N/A

Stock dmesg:
https://pastebin.com/2t2jwLdf

Stock Dumps:
https://pastebin.com/LDLxSWX3

Installation via SSH (does not void your warranty):
1.  -----UNLOCK SSH-----
1.1 Set computer IP to DHCP mode, load 'http://10.168.1.1/cgi-bin/luci' in
    your browser. Password is 'admin'.
1.2 Click the "备份且导出" (backup and export) button, and download the
    config file.
1.3 Open the downloaded file with 7zip, navigate to '/etc/config/'.
1.4 Edit the file './system'. Change the '0' into '1' under
    "config sys 'ssh'".
1.5 Save the file.
1.6 Upload the file by clicking the "导入且恢复" (import and recover)
    button. The router will automatically reboot.
2.  -----FLASH THE OPENWRT FIRMWARE-----
2.1 Use any scp tool to upload the 'sysupgrade' firmware to the '/tmp/'
    folder to your router. It should be root@10.168.1.1 and the password
    is 'admin'.
2.2 SSH into the router, also root@10.168.1.1 and the password is 'admin'.
2.3 **IMPORTANT** Type command 'dd if=/dev/mtd3 of=/tmp/firmware.bin', to
    backup the stock firmware. Since the OEM does not provide firmware
    download on their website, this is the only way to get it.
2.3 **ALSO IMPORTANT** Use any scp tool to download your backed-up stock
    firmware from '/tmp/' to your local drive. Then you'd better use a hex
    reading tool to have a rough look at it to make sure nothing is
    corrupt. Or u can just back up again and cross check the MD5.
2.4 Type command 'mtd write /tmp/XXX.bin firmware', and it should flash
    the firmware.
2.5 Verify that nothing went wrong. If you're confident, type 'reboot' and
    reboot the router.

Revert to stock firmware:
1.  load stock firmware using mtd (make sure u have a backup).

Signed-off-by: Ray Wang <raywang777@foxmail.com>
2022-04-17 14:10:11 +02:00
Russell Morris
fb3f519e59 ramips: mt7621: make u_env partition r/w for Linksys EA7xxx devices
Make u_env partition read/write - currently cannot write to it, which
blocks fw_setenv. This in turn breaks features like Advanced Reboot,
which rely on setting the environment variable boot_part (1 or 2).

Signed-off-by: Russell Morris <rmorris@rkmorris.us>
2022-04-16 16:59:29 +02:00
Tamas Balogh
a4bf562aa7 ramips: add support for ASUS RT-AC1200-V2
Hardware specifications:
SoC: MT7628DAN MIPS_24KEc@580MHz 2.4G-n 2x2
WiFi: MT7613BEN 5G-ac 160MHz 2x2
Switch: 4x100M built-in SoC
Flash: 16MB W25Q128JVSQ SPI-NOR
DRAM: 64MB built-in SoC

MAC addresses as verified by OEM firmware:
use address source
Lan/Wan/2G *:60 factory 0x4 (label)
5G *:64 factory 0x8000

Serial console: 57600,8n1

Installation:

Asus windows recovery tool:

install the Asus firmware restoration utility
unplug the router, hold the reset button while powering it on
release when the power LED flashes slowly
specify a static IP on your computer:
IP address: 192.168.1.75
Subnet mask 255.255.255.0
start the Asus firmware restoration utility, specify the factory image
and press upload
do NOT power off the device after OpenWrt has booted until the LED flashing
after flashing OpenWrt, there will be first no 5GHz Wifi available probably,
wait until blinking finishes and do a reboot
TFTP Recovery method:

set computer to a static ip, 192.168.1.75
connect computer to the LAN 1 port of the router
hold the reset button while powering on the router for a few seconds
send firmware image using a tftp client; i.e from linux:
$ tftp
tftp> binary
tftp> connect 192.168.1.1
tftp> put factory.bin
tftp> quit
do NOT power off the device after OpenWrt has booted until the LED flashing
after flashing OpenWrt, there will be first no 5GHz Wifi available probably,
wait until blinking finishes and do a reboot

Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
2022-04-16 15:30:11 +02:00
Abdul Aziz Amar
78c3534645 ramips: add support for BOLT! Arion
This device is from now-defunct BOLT! ISP in Indonesia.
The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision.

Specifications:

- SoC:      MediaTek MT7621
- Flash:    32 MiB NOR SPI
- RAM:      128 MiB DDR3
- Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN)
- WIFI0:    MT7603E 2.4GHz 802.11b/g/n
- WIFI1:    MT7612E 5GHz 802.11ac
- Antennas: 2x internal, non-detachable
- LEDs:     Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1)
            Non-programmable "Power"  LED
- Buttons:  Reset and WPS

Instalation:
Install from TFTP

Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123
Press "1" when turning on the router, and type the initramfs file name

You also need to solder pin header or cable to J4 or neighboring test points (T19-T21)
Pinouts from top to bottom: GND, TX, RX, VCC (3.3v)
Baudrate: 57600n8

There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB.

Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com>
2022-04-16 14:02:11 +02:00
Davide Fioravanti
bb505d82ad ramips: add support for Wavlink WL-WN531A3
The Wavlink WL-WN531A3 is an AC1200 router with 5 fast ethernet ports
and one USB 2.0 port.
It's also known as Wavlink QUANTUM D4.

Hardware
--------
SoC:   Mediatek MT7628AN
RAM:   64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CSIG3)
ETH:
  - 5x 10/100 Mbps Ethernet (4x LAN + 1x WAN)
WIFI:
  - 2.4GHz: 1x (integrated in SOC) (2x2:2)
  - 5GHz:   1x MT7612E (2x2:2)
  - 4 external antennas
BTN:
  - 1x Reset button
  - 1x WPS button
  - 1x Turbo button
  - 1x Touchlink button
  - 1x ON/OFF switch
LEDS:
  - 1x Red led (system status)
  - 1x Blue led (system status)
  - 7x Blue leds (wifi led + 5 ethernet ports + power)
USB:
  - 1x USB 2.0 port
UART:
  - 57600-8-N-1
    J1
      O VCC +3,3V (near lan ports)
      o RX
      o TX
      o GND

Everything works correctly.

Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.

Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on M31A3.V4300.200420 firmware version.

1) Go to http://192.168.10.1/webcmd.shtml

2) Type the following line in the "Command" input box and then press enter:
	mkdir /etc_ro/lighttpd/www/dev; cp /dev/mtd0ro /etc_ro/lighttpd/www/dev/mtd0ro; ls -la /etc_ro/lighttpd/www/dev/mtd0ro

3) After few seconds in the textarea should appear this output:
	-rw-r--r--    1 0        0         8388608 /etc_ro/lighttpd/www/dev/mtd0ro

   If your output doesn't match mine, stop reading and ask for
   help in the forum.

4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the
   content of the whole NOR. If the file size is 0 byte, stop reading
   and ask for help in the forum.

5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type:
	rm /etc_ro/lighttpd/www/dev/mtd0ro; for i in 1 2 3 4 ; do cp /dev/mtd${i}ro /etc_ro/lighttpd/www/dev/mtd${i}ro; done; ls -la /etc_ro/lighttpd/www/dev/

6) After few seconds, in the textarea should appear this output:
	-rw-r--r--    1 0        0          196608 mtd1ro
	-rw-r--r--    1 0        0           65536 mtd2ro
	-rw-r--r--    1 0        0           65536 mtd3ro
	-rw-r--r--    1 0        0         8060928 mtd4ro
	drwxr-xr-x    7 0        0               0 ..
	drwxr-xr-x    2 0        0               0 .

   If your output doesn't match mine, stop reading and ask for
   help in the forum.

7) Open the following links to download the partitions of the OEM FW:
	http://192.168.10.1/dev/mtd1ro
	http://192.168.10.1/dev/mtd2ro
	http://192.168.10.1/dev/mtd3ro
	http://192.168.10.1/dev/mtd4ro

   If one (or more) of these files are 0 byte, stop reading and ask
   for help in the forum.

8) Store these downloaded files in a safe place.

9) Reboot your router to remove any temporary file in ram.

Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.

Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Notes
-----
1) Router mac addresses:
   LAN		XX:XX:XX:XX:XX:9B (factory @ 0x28)
   WAN		XX:XX:XX:XX:XX:9C (factory @ 0x2e)
   WIFI 2G	XX:XX:XX:XX:XX:9D (factory @ 0x04)
   WIFI 5G	XX:XX:XX:XX:XX:9E (factory @ 0x8004)

   LABEL	XX:XX:XX:XX:XX:9D

2) There is just one wifi led for both wifi interfaces.
   It currently shows only the 2.4 GHz wifi activity.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2022-04-16 14:02:11 +02:00
Rui Salvaterra
be381a7ac7 kernel: bump 5.15 to 5.15.33
Deleted (upstreamed):
generic/backport-5.15/350-v5.18-MIPS-pgalloc-fix-memory-leak-caused-by-pgd_free.patch [1]
generic/backport-5.15/730-v5.16-hv-utils-add-PTP_1588_CLOCK-to-Kconfig-to-fix-build.patch [2]
generic/pending-5.15/850-0014-PCI-aardvark-Fix-reading-PCI_EXP_RTSTA_PME-bit-on-em.patch [3]
generic/pending-5.15/850-0002-PCI-aardvark-Fix-reading-MSI-interrupt-number.patch [4]

Manually rebased:
generic/pending-5.15/850-0002-PCI-aardvark-Fix-reading-MSI-interrupt-number.patch
ramips/patches-5.15/710-at803x.patch

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.33&id=d29cda15cab086d82d692de016f7249545d4b6b4
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.33&id=d5aad7d63b1b5c1f3c4b69e12c05e7c7d196fae8
[3] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.33&id=ed750e22e44366e264bcdf7b1cf0713f08f7980a
[4] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.33&id=0fe94b84c43cfea867e1721606185e8686d7d32f

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[Refresh patches again]
[Remove generic/pending-5.15/850-0002-PCI-aardvark-Fix-reading-MSI-interrupt-number.patch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-04-09 19:31:46 +02:00
Aleksander Jan Bajkowski
a98ded6c5c kernel: move some symbols to generic config
This commit add some enabled symbols to generic config.
LTO is only supported by clang compiler and therefore should
be disabled in the generic config instead of duplicating this
symbol in each target. CONFIG_LTO_NONE do this job.

The second group of symbols is enabled by the options available
in the generic config and is therefore added here:
* CONFIG_AF_UNIX_OOB is selected by CONFIG_NET && CONFIG_UNIX,
* CONFIG_BINARY_PRINTF is selected by CONFIG_BPF_SYSCALL,
* CONFIG_NET_SOCK_MSG is selected by CONFIG_BPF_SYSCALL && CONFIG_NET.

The other symbols are disabled and should be in the generic config.

This commit also removes these symbols from subtargets.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-04-09 19:31:46 +02:00
John Audia
c41da167d2 kernel: bump 5.10 to 5.10.109
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <graysky@archlinux.us>
2022-03-30 18:33:38 +02:00
Felix Fietkau
92081f9a34 ramips: fix kernel module build errors on linux 5.15
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-28 11:03:13 +02:00
Felix Fietkau
a3764ee29d ramips: add linux 5.15 support for mt7621
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-27 21:36:40 +02:00
Felix Fietkau
0f029b3d2b mediatek: add patches for MT7622 WED (wireless ethernet dispatch)
This series also contains other improvement for hardware flow offload support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-27 12:54:38 +02:00
Shiji Yang
2e6d19ee32 ramips: fix wifi mac address of HiWiFi series devices
For HiWiFi series devices, label_mac can be read from bdinfo partition,
and lan_mac, wlan2g_mac are same as the label_mac. Converting label_mac
to wlan5g_mac only needs to unset 6th bit. (It seems that all HiWiFi's
label_mac start with D4:EE)

For example:
label	D4:EE:07:32:84:88
lan	D4:EE:07:32:84:88
wan	D4:EE:07:32:84:89
wlan2g	D4:EE:07:32:84:88
wlan5g	D0:EE:07:32:84:88

Tested on HiWiFi HC5661.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-03-26 02:02:44 +01:00
Felix Fietkau
55e8d52157 ramips: skip bbt scan on mt7621
reduces unnecessary flash reads and speeds up boot time

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-25 21:11:09 +01:00
Felix Fietkau
4947623d6c ramips: enable support for mtk_bmt in the nand flash driver
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-25 21:11:09 +01:00
Felix Fietkau
73b2a4ca03 ramips: mt7621_nand: initialize ECC_FDMADDR
This is needed for the ECC controller to access FDM data

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-03-25 21:11:09 +01:00
Stijn Tintel
89c1959251 ramips: mt7621_nand: reduce log verbosity
Avoid flooding the log with the message below by increasing the log
level to debug:

  mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-03-25 21:11:09 +01:00
Stijn Tintel
2f2e81a4ea ramips: move mt7621_nand driver to files
The patch was rejected by upstream. The mtk_nand driver should be
modified to support the mt7621 flash controller instead. As there is no
newer version to backport, or no upstream version to fix bugs, let's
move the driver to the files dir under the ramips target. This makes it
easier to make changes to the driver while waiting for mt7621 support to
land in mtk_nand.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-03-25 21:11:09 +01:00
Igor Nazarov
42626aef67 ramips: add support for D-Link DIR-878 R1
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz)
- Switch: 1 WAN, 4 LAN (Gigabit)
- Buttons: Reset, WiFi Toggle, WPS
- LEDs: Power, Internet, WiFi 2.4G WiFi 5G

The R1 revision is identical to the A1 revision except
- No Config2 Parition, therefore
- factory partition resized to 64k from 128K
- Firmware partition offset is 0x50000 not 0x60000
- Firmware partitions size increased by 64K
- Firmware partition type is "denx,uimage", not "sge,uimage"
- Padding of image creation "uimage-padhdr 96" removed

Installation:
Update to the last D-Link firmware through web-ui before OpenWRT
installation then follow the instructions to patch your device using
D-Link FailsafeUI.

- D-Link FailsafeUI:
Power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing, then jack into any lan port and manually assign a static IP
address in 192.168.0.0/24 other than 192.168.0.1 (e.g. 192.168.0.2)
and go to http://192.168.0.1
Flash with the factory image.

Signed-off-by: Igor Nazarov <tigron.dev@gmail.com>
2022-03-19 19:51:20 +01:00
Mikhail Zhilkin
f8b02130d2 ramips: add support for Beeline SmartBox Flash
Beeline SmartBox Flash is a wireless AC1300 (WiFi 5) router manufactured
by Arcadyan company.

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB, Winbond W632GU6NB
Flash: 128 MiB (NAND), Winbond W29N01HVSINF
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: 1xUSB3.0
Button: 1 (Reset/WPS)
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WE42022

Installation
------------
1. Place *factory.trx on any web server (192.168.1.2 in this example)
2. Connect to the router using telnet shell (no password required)
3. Save MAC adresses to U-Boot environment:
   uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
    awk '{print $5}')
   uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
    awk '{print $5}')
   uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
    awk '{print $5}')
   uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
    awk '{print $5}')
4. Ensure that MACs were saved correctly:
   uboot_env --get --name eth2macaddr
   uboot_env --get --name eth3macaddr
   uboot_env --get --name ra0macaddr
   uboot_env --get --name rax0macaddr
5. Download and write the OpenWrt images:
   cd /tmp
   wget http://192.168.1.2/factory.trx
   mtd_write erase /dev/mtd4
   mtd_write write factory.trx /dev/mtd4
6. Set 1st boot partition and reboot:
   uboot_env --set --name bootpartition --value 0
   reboot

Back to Stock
-------------
1. Run in the OpenWrt shell:
   fw_setenv bootpartition 1
   reboot
2. Optional step. Upgrade the stock firmware with any version to
   overwrite the OpenWrt in Slot 1.

MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC               | Source         |
+-----------+-------------------+----------------+
| label     | 30:xx:xx:51:xx:09 | No MACs was    |
| LAN       | 30:xx:xx:51:xx:09 | found on Flash |
| WAN       | 30:xx:xx:51:xx:06 | [1]            |
| WLAN_2g   | 30:xx:xx:51:xx:07 |                |
| WLAN_5g   | 32:xx:xx:41:xx:07 |                |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
   key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
   with saving of the MACs to u-boot-env during the installation was
   applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:36) was found in
   "Factory" 0xfff0. It's the same for all Smartbox Flash devices. OEM
   firmware also uses this MAC when initialazes ethernet driver. In
   OpenWrt we use it only as internal GMAC (eth0), all other MACs are
   unique. Therefore, there is no any barriers to the operation of several
   Smartbox Flash devices even within the same broadcast domain.

Stock firmware image format
---------------------------
+--------------+---------------+----------------------------------------+
| Offset       | 1.0.15        | Description                            |
+==============+===============+========================================+
| 0x0          | 5d 43 6f 74   | TRX magic "]Cot"                       |
+--------------+---------------+----------------------------------------+
| 0x4          | 00 70 ff 00   | Length (reverse)                       |
+--------------+---------------+----------------------------------------+
|              |               | htonl(~crc) from 0xc ("flag_version")  |
| 0x8          | 72 b3 93 16   | to "Length"                            |
+--------------+---------------+----------------------------------------+
| 0xc          | 00 00 01 00   | Flags                                  |
+--------------+---------------+----------------------------------------+
|              |               | Offset (reverse) of Kernel partition   |
| 0x10         | 1c 00 00 00   | from the start of the header           |
+--------------+---------------+----------------------------------------+
|              |               | Offset (reverse) of RootFS partition   |
| 0x14         | 00 00 42 00   | from the start of the header           |
+--------------+---------------+----------------------------------------+
| 0x18         | 00 00 00 00   | Zeroes                                 |
+--------------+---------------+----------------------------------------+
| 0x1c         | 27 05 19 56 … | Kernel data + zero padding             |
+--------------+---------------+----------------------------------------+
|              |               | RootFS data (starting with "hsqs") +   |
| 0x420000     | 68 73 71 73 … | zero padding to "Length"               |
+--------------+---------------+----------------------------------------+
|              |               | Some signature data (format is         |
|              |               | unknown). Necessary for the fw         |
| "Lenght"     | 00 00 00 00 … | update via oem fw web interface.       |
+--------------+---------------+----------------------------------------+
| "Lenght" +   |               | TRX magic "HDR0". U-Boot is            |
| 0x10c        | 48 44 52 30   | checking it at every boot.             |
+--------------+---------------+----------------------------------------+
|              |               | 1.00:                                  |
|              |               |   Zero padding to ("Lenght" + 0x23000) |
|              |               | 1.0.12:                                |
|              |               |   Zero padding to ("Lenght" + 0x2a000) |
| "Lenght" +   |               | 1.0.13, 1.0.15, 1.0.16:                |
| 0x110        | 00 00 00 00   |   Zero padding to ("Lenght" + 0x10000) |
+--------------+---------------+----------------------------------------+

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-03-19 16:14:01 +01:00
Rodolphe de Saint Léger
46c5de5385 ramips: add support for Netgear WN3100RPv2
This patch adds support for the Netgear WN3100RPv2
http://www.netgear.com/support/product/wn3100rpv2.aspx

Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Stock firmware based on OpenWRT Kamikaze

Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577

This device seems to be same hardware as a WN3000RPv3

Flash instructions:
- Use the Netgear WebUI to upgrade to OpenWRT using the factory image
  (see note below),
- Use the sysupgrade image for upgrading versions from OpenWRT,
- TFTP recovery procedure can be used to flash the factory image
  (preferred method).

Note:
- The WebUI may not reboot automatically, wait at least 5 minutes before
  powercycling the device

Flashing using TFTP:
- Set you IP address to 192.168.1.10/24 (no gateway)
- Connect your machine to the Ethernet port
- Power off the device and wait for 10 seconds,
- Hold the reset button and power on the device (do not release reset),
- Hold the reset button until the green light is flashing (Approx. 15s)
- launch tftp, set mode to binary and connect to 192.168.1.1
- put the factory firmware image
- All leds will switch off (like a power off), this is normal
- Wait for the device to reboot in the new OpenWRT image (max 5 mins)
- The first boot will take longer than usual.
- After boot, the Device IP on the ethernet port is 192.168.1.1

Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com>
[drop unneeded includes in dts, wrap commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-03-16 23:14:25 +09:00
Sungbo Eo
fe34001ee5 Revert "ramips: add support for Netgear WN3000RPv3"
This reverts commit 7bc20cb614.

It adds support for Netgear WN3100RPv2, but the commit title is wrong.
It will be re-added with the correct title.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-03-16 23:10:45 +09:00
Rodolphe de Saint Léger
7bc20cb614 ramips: add support for Netgear WN3000RPv3
This patch adds support for the Netgear WN3100RPv2
http://www.netgear.com/support/product/wn3100rpv2.aspx

Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Stock firmware based on OpenWRT Kamikaze

Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577

This device seems to be same hardware as a WN3000RPv3

Flash instructions:
- Use the Netgear WebUI to upgrade to OpenWRT using the factory image
  (see note below),
- Use the sysupgrade image for upgrading versions from OpenWRT,
- TFTP recovery procedure can be used to flash the factory image
  (preferred method).

Note:
- The WebUI may not reboot automatically, wait at least 5 minutes before
  powercycling the device

Flashing using TFTP:
- Set you IP address to 192.168.1.10/24 (no gateway)
- Connect your machine to the Ethernet port
- Power off the device and wait for 10 seconds,
- Hold the reset button and power on the device (do not release reset),
- Hold the reset button until the green light is flashing (Approx. 15s)
- launch tftp, set mode to binary and connect to 192.168.1.1
- put the factory firmware image
- All leds will switch off (like a power off), this is normal
- Wait for the device to reboot in the new OpenWRT image (max 5 mins)
- The first boot will take longer than usual.
- After boot, the Device IP on the ethernet port is 192.168.1.1

Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com>
[drop unneeded includes in dts, wrap commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-03-16 22:36:04 +09:00
Pawel Dembicki
be89c9eec4 ramips: mt7620: Add support for D-Link DWR-961 A1
The DWR-961 A1 Wireless Router is based on the MT7620A SoC.
It's a merge of two Amit boards: DWR-960 with ethernet part
of Lava LR-25G001.

ROMID it's taken from Telenor branded version and it works with tested
device. Images from D-Link site for this router are from DWR-953 and it
have ROMID DLK6E2424001. I don't know if it's mistake on web-site
or if it's will require different image.

Specification:

- MediaTek MT7620A (580 Mhz)
- 128 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612 mpcie card)
- 5x 10/100/1000 Mbps Ethernet: 4xLAN and 1xWAN (QCA8337)
- 2x internal, non-detachable antennas (Wifi 2.4G)
- 3x external, detachable antennas (2x LTE, 1x Wifi 5G)
- 1x LTE modem cat 6
- UART (J5) header on PCB (57600 8n1)
- 13x LED, 2x button
- JBOOT bootloader

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-03-16 22:31:14 +09:00
Joe Mullally
8d25551243 ramips: Apply pinctrl DTS changes to TL-WPA8631P
Applies changes from 7774b86019 to new device committed later. Fix some
whitespace in the DTS. Use standard model name format in DTS.

Fixes: 6c743c3006 ("ramips: Add support for TP-Link TL-WPA8631P v3")
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2022-03-13 12:39:58 +09:00
Chukun Pan
7fa227ead5 ramips: update WLAN MAC address of JCG Y2
MAC addresses on OEM firmware:
  04:xx:xx:xx:xx:c8  factory 0x4     wlan2g
  06:xx:xx:xx:xx:c8  [not on flash]  wlan5g

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-03-13 12:39:58 +09:00
Chukun Pan
285e636b16 ramips: update WLAN MAC address of Phicomm K2P
The wireless mac address difference of this machine is similar
to that of D-Link DIR-853-R1, so use the same practice.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-03-13 12:39:58 +09:00
Dawsen Gao
b3da44b647 ramips: Add support for Dual-Q H721
Dual-Q H721 is a router platform board, it is the smaller model of
the U7621-06.

The device has the following specifications:

MT7621AT (880 MHz)
256 of RAM (DDR3)
16 MB of FLASH (MX25l12805d SPI)
5x 1 Gbps Ethernet (MT7621 built-in switch)
1x M.2 (NGFF) 3.7V 3A max for 5G M.2 Modem work at USB3.0 mode
1x Minipcie 3.7V 3A max for LTE Modem work at USB2.0 Mode
2x Minipcie for WIFI card
4x Lan+1x Wan 10/100M/1000M RJ45 port
14x LEDs (1x GPIO-controlled)
1x reset button
1x UART header (4-pins)
1x mico SD-card reader
1x DC jack for main power (5~27 V)

The following has been tested and is working:

Ethernet switch
miniPCIe slots (tested with Wi-Fi cards and LTE modem cards)
miniSIM slot (works with normal size simcard)
sysupgrade
reset button
micro SD-card reader

Installation:

This board has no locked down bootloader. The seller can be asked to
install openwrt, so upgrades are standard sysupgrade method.

Recovery:

This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.

Signed-off-by: Dawsen Gao <dawsen_gao@163.com>
[change author name (used SoB one), add ethernet pinctrl,
 apply sorting to device recipe]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-03-13 12:37:25 +09:00
Dmitry Chigiryov
9d06f1a618 ramips: allow USB power control on TP-Link MR3020v3
By switching EPHY_LED4_N_JTRST_N from EPHY_LED4_N to GPIO#39
we can control USB port power an all current revisions of MR3020v3.
It was not a thing on some first revisions, pin was unused.
But for now on all current MR3020v3 boards EPHY_LED4_N_JTRST_N pin
is connected to USB power key.
Also it was not used as EPHY indicator on any revision of the board.

Signed-off-by: Dmitry Chigiryov <dmitry.chigiryov@ya.ru>
[changed author address (used SoB one)]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-03-09 15:44:51 +09:00
Sungbo Eo
94d4269ec7 ramips: fix DEVICE_VENDOR for unbranded devices
In commit ee66fe4ea9 ("ramips: convert DEVICE_TITLE to new variables"),
DEVICE_VENDOR of some unbranded devices were set incorrectly:
* WR512-3GN is not a dev board from Ralink.
* "XDX-RN502J" is the whole model name and should be not split.

This patch sets their DEVICE_VENDOR to "Unbranded", and changes their DTS
model properties accordingly.

Ref: d0bf15f235 ("ramips: add support for A5-V11 board (resubmit)")
Ref: 9085b05d9e ("ramips: rt305x: support for wr512-3gn-like routers")
Ref: 0e486d2fd2 ("ramips: add support for unbranded XDX-RN502J board")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-03-09 15:38:36 +09:00
Kim Namu
2876f7534f ramips: mt7621: add support for Zbtlink ZBT-WG1608
Zbtlink ZBT-WG1608 is a Wi-Fi router intendent to use with WWAN (4G/5G)
modems.

Specifications:
* SoC: MediaTek MT7621A
* RAM: 256/512 MiB
* Flash: 16/32 MiB (SPI NOR)
* Wi-Fi:
  * MediaTek MT7603E : 2.4Ghz
  * MediaTek MT7613BE : 5Ghz
* Ethernet: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
* M.2: 1x slot with USB&SIM
  * EM7455/EM12-G/EM160R/RM500Q-AE
* USB: 1x 3.0 Type-A port
* External storage: 1x microSD (SDXC) slot
* UART: console (115200 baud)
* LED:
  * 1 power indicator
  * 1 WLAN 2.4G controlled (wlan 2G)
  * 3 SoC controlled (wlan 5G, wwan, internet)
  * 5 per Eth phy (4xLAN + WAN)

MAC Addresses:
* LAN    : f8:5e:3c:xx:xx:e0 (Factory, 0xe000 (hex))
* WAN    : f8:5e:3c:xx:xx:e1 (Factory, 0xe006 (hex))
* 2.4 GHz: f8:5e:3c:xx:xx:de (Factory, 0x0004 (hex))
* 5 GHz  : f8:5e:3c:xx:xx:df (Factory, 0x8004 (hex))

Installation:
* Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can
  be directly used to install OpenWrt. Firmware must be upgraded using the
  'force' and 'do not save configuration' command line options (or
  correspondig web interface checkboxes) since the vendor firmware is from
  the pre-DSA era.

Recovery Mode:
 * Press reset button, power up the device, wait for about 10sec.
 * Upload sysupgrade image through the firmware recovery mode web page at
  192.168.1.1.

Signed-off-by: Kim Namu <namu@theseed.io>
2022-03-09 15:38:32 +09:00
Ray Wang
3c4810fecc ramips: add support for Asus RT-AC1200
Asus RT-AC1200 is a 2.4/5GHz dual band AC router,
based on MediaTek MT7628AN.

Specification:
* SoC: MT7628AN
* RAM: DDR2 64 MiB
* Flash: 16 MiB NOR (W25Q128BV)
* Wi-Fi:
  * 2.4GHz: SoC Built-in
  * 5GHz: MT7612EN
* Ethernet: 5x 100Mbps
  * Switch: SoC built-in
* USB: 1x 2.0

Flash Layout:
 0x0000000-0x0030000 : "bootloader"
 0x0030000-0x0040000 : "nvram"
 0x0040000-0x0050000 : "factory"
 0x0050000-0x1000000 : "firmware"

MAC address:
 LAN: factory 0x28
 WAN: factory 0x22
 2.4G: factory 0x4
 5G: factory 0x8004

Installation via **recovery** mode:
1. Download the Asus recovery firmware (windows) tool from
   http://dlcdnet.asus.com/pub/ASUS/LiveUpdate/Release/Wireless/Rescue.zip
2. Set your ethernet IP manually 192.168.1.5 / 255.255.255.0 with NO
   gateway.
3. Plug in your ethernet to LAN port 1 on the router.
4. Load up the recovery software with the firmware file, but don't press
   "Upload" yet.
5. Plug in the router to power WHILE HOLDING the reset button in. While
   CONTINUING to hold the button, select "Upload" Continue to hold the
   reset button in until it finishes and verifies!
6. If that doesn't work try pressing "Upload" first just before you do
   step 5. At some point while holding reset the rescue tool will finally
   detect and upload the firmware. That's when you can let go of the
   reset button.
7. The router will reboot and not much will happen. Wait a minute or 2.
8. Power off and on the router again. Voila. Set everything your Ethernet
   IP back to DHCP (automatically) and you're good to go.

Revert to stock firmware:
1. Install stock image via recovery mode.

Tested-by: Ivan Pavlov <AuthorReflex@gmail.com>
Signed-off-by: Ray Wang <raywang777@foxmail.com>
2022-03-09 15:38:28 +09:00
Birger Koblitz
ed364cd4b0 ramips: add support for Renkforce WS-WN530HP3-A
This adds support for the Renkforce WS-WN530HP3-A ceiling-
mountable Wireless Access Point, which is powered over PoE.
Hardware:
	- SoC: Mediatek MT7621DAT
	- RAM: 128MiB on SoC
	- Flash: 16MiB GigaDevice GD25Q128C
	- 2.4Ghz Wifi: Mediatek MT603EN
	- 5GHz Wifi: MT613BEN
	- Ethernet:
	  - 1x 1GBit WAN port, passive PoE capable
	  - 2x 1GBit LAN ports
	LEDs: 1x Bi-Color LED (red/blue)
	Buttons: 1x Reset Button, 1x Power Button

Installation:
	Power on the access point and immedately press the reset
	button for 10 seconds. Connect web-browser to 192.168.10.1
	and upload sysupgrade image. Flash uploaded image and wait
	about 2 minutes for reboot.

Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [fixed SoB]
2022-03-08 18:34:32 +01:00
INAGAKI Hiroshi
f7f9e6bd20 ramips: use parser_trx for Buffalo WCR-1166DS
Buffalo WCR-1166DS uses trx-fomatted firmware and the custom magic
number (0x5C436F74, "\Cot") is required for OpenWrt installation from
OEM WebUI.
But the current mtdsplit_trx doesn't support the custom magic number and
fail to parse and split to kernel and rootfs when the factory image is
flashed. Then, the kernel fails to mount rootfs automatically and panics.

Before the commit fddc78bc11, mtdsplit_trx
was patched in ramips target and the device-specific magic number was
supported only for WCR-1166DS[1].
But the patch was not inherited to the later version of the kernel and
deleted by the above commit, then, the custom magic number support was
broken.

[1]: 05d6e92594/target/linux/ramips/patches-4.4/0400-mtd-mtdsplit-add-support-for-custom-trx-magic-for-Buffalo-WCR-1166DS.patch (L27)

log (factory image):

[    1.165312] spi-mt7621 10000b00.spi: sys_freq: 193333333
[    1.195782] spi-nor spi0.0: w25q128 (16384 Kbytes)
[    1.205353] 7 fixed-partitions partitions found on MTD device spi0.0
[    1.217938] Creating 7 MTD partitions on "spi0.0":
[    1.227436] 0x000000000000-0x000000030000 : "u-boot"
[    1.238427] 0x000000030000-0x000000040000 : "u-boot-env"
[    1.250123] 0x000000040000-0x000000050000 : "factory"
[    1.261306] 0x000000050000-0x000000810000 : "firmware"
[    1.282051] 0x000000810000-0x000000fd0000 : "firmware2"
[    1.293594] 0x000000fd0000-0x000000fe0000 : "glbcfg"
[    1.304719] 0x000000fe0000-0x000000ff0000 : "board_data"
...
[    1.452424] /dev/root: Can't open blockdev
[    1.460619] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[    1.475434] Please append a correct "root=" boot option; here are the available partitions:
[    1.491986] 1f00             192 mtdblock0
[    1.491989]  (driver?)
[    1.504938] 1f01              64 mtdblock1
[    1.504941]  (driver?)
[    1.517885] 1f02              64 mtdblock2
[    1.517888]  (driver?)
[    1.530831] 1f03            7936 mtdblock3
[    1.530834]  (driver?)
[    1.543777] 1f04            7936 mtdblock4
[    1.543781]  (driver?)
[    1.556724] 1f05              64 mtdblock5
[    1.556727]  (driver?)
[    1.569672] 1f06              64 mtdblock6
[    1.569675]  (driver?)
[    1.582617] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    1.598976] Rebooting in 1 seconds..

This patch fixes this issue by using parser_trx with specifying custom
magic number in dts instead of mtdsplit_trx.

log (fixed factory image):

[    1.202044] spi-mt7621 10000b00.spi: sys_freq: 193333333
[    1.225369] spi-nor spi0.0: w25q128 (16384 Kbytes)
[    1.235015] 7 fixed-partitions partitions found on MTD device spi0.0
[    1.247603] Creating 7 MTD partitions on "spi0.0":
[    1.257106] 0x000000000000-0x000000030000 : "u-boot"
[    1.269447] 0x000000030000-0x000000040000 : "u-boot-env"
[    1.281192] 0x000000040000-0x000000050000 : "factory"
[    1.294208] 0x000000050000-0x000000810000 : "firmware"
[    1.305774] 2 trx partitions found on MTD device firmware
[    1.316540] Creating 2 MTD partitions on "firmware":
[    1.326399] 0x00000000001c-0x000000214754 : "linux"
[    1.336063] mtd: partition "linux" doesn't start on an erase/write block boundary -- force read-only
[    1.357070] 0x000000214754-0x0000007c0000 : "rootfs"
[    1.366994] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only
[    1.386368] mtd: device 5 (rootfs) set to be root filesystem
[    1.398700] 1 squashfs-split partitions found on MTD device rootfs
[    1.411027] 0x000000520000-0x0000007c0000 : "rootfs_data"
[    1.422841] 0x000000810000-0x000000fd0000 : "firmware2"
[    1.436282] 0x000000fd0000-0x000000fe0000 : "glbcfg"
[    1.447408] 0x000000fe0000-0x000000ff0000 : "board_data"
...
[    1.611216] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-03-06 20:40:35 +01:00
INAGAKI Hiroshi
5403defbec ramips: switch parser of trx for mt76x8 subtarget
This patch enable parser_trx and disable mtdsplit_trx for mt76x8
subtarget.
The trx format is used only on Buffalo WCR-1166DS in mt76x8 subtarget
and the parser need to be switched to parser_trx to use the custom magic
number in the header for WCR-1166DS.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-03-06 20:40:35 +01:00
INAGAKI Hiroshi
770cfe9bff ramips: update MAC address configuration for Buffalo WCR-1166DS
This patch converts MAC address configuration of Buffalo WCR-1166DS in
02_network to use the generic function of OpenWrt. And also, add
label_mac.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-03-06 20:05:45 +01:00
INAGAKI Hiroshi
621d88d741 ramips: increase spi frequency for Buffalo WCR-1166DS
Use higher frequency than current and up the speed to access to the
flash on WCR-1166DS.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-03-06 20:05:45 +01:00
Joe Mullally
6c743c3006 ramips: Add support for TP-Link TL-WPA8631P v3
AV1300 Gigabit Passthrough Powerline ac Wi-Fi Extender

Specifications
--------------
* SoC: MediaTek MT7621AT
* CPU: 880 MHz MIPS 1004KEc dual-core CPU
* RAM: 64 MiB DDR2 (Zentel A3R12E40DBF-8E)
* Flash: 8 MiB SPI NOR (GigaDevice GD25Q64CSIG)
* Ethernet: SoC built-in Switch 5x 1GbE
  * Port 0: PLC (connected through AR8035-A)
  * Port 1-3: LAN
* WLAN: 2x2 2.4GHz 300 Mbps + 2x2 5GHz 867 Mbps (MT7603EN + MT7613BEN)
* PLC: HomePlug AV2 (Qualcomm QCA7500)
* PLC Flash: 2MiB SPI NOR (GigaDevice GD25Q16CSIG)
* Buttons: Reset, LED, Pair, Wi-Fi
* LEDs: Power (green), PLC (green/amber), LAN (green), 2.4G (green),
  5G (green)
* UART: J1 (57600 baud)
  * Pinout: (3V3) (GND) (RX) (TX)
  * Visually identify GND from connection to PCB ground plane

Installation
------------
Installation is possible from the OEM web interface. Make sure to install
the latest OEM firmware first, so that the PLC firmware is at the latest
version. However, please first check the OpenWRT Wiki page for
confirmation that your OEM firmware version is supported.

Signed-off-by: Joe Mullally <jwmullally@gmail.com>
2022-03-06 18:57:33 +01:00
John Audia
0989b7ad3a kernel: bump 5.10 to 5.10.102
Removed upstreamed:
	bcm4908/patches-5.10/180-i2c-brcmstb-fix-support-for-DSL-and-CM-variants.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.102&id=f333c1916fd6b55900029bf8f918cc00009e2111

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <graysky@archlinux.us>
2022-03-01 21:38:36 +01:00
Petr Štetiar
fb2801b82c mt7620: fix missing kernel config symbol
Fixes following missing kernel config symbol after adding GPIO watchdog:

  Software watchdog (SOFT_WATCHDOG) [M/n/y/?] m
  Watchdog device controlled through GPIO-line (GPIO_WATCHDOG) [Y/n/m/?] y
    Register the watchdog as early as possible (GPIO_WATCHDOG_ARCH_INITCALL) [N/y/?] (NEW)

Fixes: 1a97c03d86 ("rampis: feed zbt-we1026 external watchdog")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-02-28 21:32:32 +01:00
Arvid E. Picciani
1a97c03d86 rampis: feed zbt-we1026 external watchdog
Without feeding the gpio watchdog, the board will reset after 90 seconds

Signed-off-by: Arvid E. Picciani <aep@exys.org>
2022-02-28 15:17:11 +01:00
Stijn Tintel
a1b8a4d7b3 ramips: support TP-Link EAP615-Wall
Add support for the TP-Link EAP615-Wall, an AX1800 Wall Plate WiFi 6 AP.
The device is very similar to the TP-Link EAP235-Wall.

Hardware:
* SoC: MediaTek MT7621AT
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Ethernet: 4x GbE
  * Back: ETH0 (PoE-PD)
  * Bottom: ETH1, ETH2, ETH3 (PoE passthrough)
* WiFi: MT7905DAN/MT7975DN 2.4/5 GHz 2T2R
* LEDS: 1x white
* Buttons: 1x LED, 1x reset

Stock firmware uses a random MAC address for ethernet. OpenWrt uses the
MAC address that is on the device label for ethernet and the wireless
interfaces. MAC address must not be incremented, as this will cause MAC
address conflicts in case you have two devices with consecutive MAC
addresses. Instead, different locally administered addresses will be
generated automatically, based on the MAC on the label.

Installation via stock firmware:
* Enable SSH in the TP-Link web interface
* SSH to the device
* Run `cliclientd stopcs`
* Upload the OpenWrt factory image via the TP-Link web interface

Installation via bootloader:
* Solder TTL header. Pinout: 1: TX, 2: RX, 3: GND, 4: VCC, with pin 1
  closest to ETH1. Baud rate 115200
* Interrupt boot process by holding a key during boot
* Boot the OpenWrt initramfs:
  # tftpboot 0x84000000 openwrt-ramips-mt7621-tplink_eap615-wall-v1-initramfs-kernel.bin
  # bootm
* Copy openwrt-ramips-mt7621-tplink_eap615-wall-v1-squashfs-sysupgrade.bin
  to /tmp and use sysupgrade to install it

Thanks to Sander Vanheule for his work on the EAP235-Wall, which made
adding support for the EAP615-Wall very easy.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Sander Vanheule <sander@svanheule.net>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2022-02-27 12:01:22 +02:00
Arınç ÜNAL
7774b86019 ramips: mt7621-dts: add pinctrl properties for ethernet
Add the missing pinctrl properties on the ethernet node.
GMAC1 will start working with this change.

Link: https://lore.kernel.org/netdev/83a35aa3-6cb8-2bc4-2ff4-64278bbcd8c8@arinc9.com/

Overwrite pinctrl-0 property without rgmii2_pins on devicetrees which use
the rgmii2 pins as GPIO (22 - 33).

Give gpio function to rgmii2 pin group on mt7621_tplink_archer-x6-v3.dtsi
which uses GPIO 28.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2022-02-26 13:36:30 +01:00
Arınç ÜNAL
704c8426fb ramips: mt7621-dts: enable flow control on port@6
Flow control needs to be enabled on both sides to work.
It is already enabled on gmac0, enable it on port@6 too.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Sungbo Eo <mans0n@gorani.run>
2022-02-26 13:36:30 +01:00
Arınç ÜNAL
2b202185d2 ramips: mt7621-dts: fix switch@1f warnings
Remove reg property from ports node to fix this warning:

Warning (unit_address_vs_reg): /ethernet@1e100000/mdio-bus/switch@1f/ports: node has a reg or ranges property, but no unit name

Another warning surfaces afterwards. Remove #address-cells and #size-cells
from switch@1f node to fix this warning:

Warning (avoid_unnecessary_addr_size): /ethernet@1e100000/mdio-bus/switch@1f: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2022-02-26 13:36:30 +01:00
Nick McKinney
61d97bf377 ramips: clean up Makefile formatting
Use correct indent in target/linux/ramips/image/mt7621.mk
to be consistent with the rest of the file.

Signed-off-by: Nick McKinney <nick@ndmckinney.net>
[rephrase commit message as Adrian suggested, fix a6004ns-m indent]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-02-20 16:16:43 +09:00
Sven Roederer
65df862b50 ramips: mt7621: print size of factory initramfs-image if it's too big
It's helpful to know the current and maximal size of the imagefiles if the
creation fails.

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
2022-02-20 15:55:36 +09:00
Yoonji Park
125b9aec29 ramips: add support for ipTIME A3002MESH
Add support for ipTIME A3002MESH.

Hardware:
- SoC: MediaTek MT7621AT (880MHz, Duel-Core)
- RAM: DDR3 128MB
- Flash: XMC XM25QH128AHIG (SPI-NOR 16MB)
- WiFi: MediaTek MT7615D (2.4GHz, 5GHz, DBDC)
- Ethernet: MediaTek MT7530 (WAN x1, LAN x2, SoC built-in)
- UART: [GND, RX, TX, 3.3V] (57600 8N1, J4)

MAC addresses:
| interface |        MAC        |     source     | comment
|-----------|-------------------|----------------|----------
|       LAN | 70:XX:XX:5X:XX:X3 |                |
|       WAN | 70:XX:XX:5X:XX:X1 | u-boot 0x1fc40 |
|   WLAN 2G | 72:XX:XX:4X:XX:X0 |                |
|   WLAN 5G | 70:XX:XX:5X:XX:X0 | factory 0x4    |
|           | 70:XX:XX:5X:XX:X0 | u-boot 0x1fc20 | unknown
|           | 70:XX:XX:5X:XX:X2 | factory 0x8004 | unknown

- WLAN 2G MAC address is not the same as stock firmware since OpenWrt
  uses LAN MAC address with local bit sets.

Installation:
1. Flash initramfs image. This can be done using stock web ui or TFTP
2. Connect to OpenWrt with an SSH connection to 192.168.1.1
3. Perform sysupgrade with sysupgrade image

Revert to stock firmware:
- Flash stock firmware via OEM TFTP Recovery mode
- Perform sysupgrade with stock image

TFTP Recovery method:
1. Unplug the router
2. Hold the reset button and plug in
3. Release when the power LED stops flashing and go off
4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0
5. Flash image with TFTP client to 192.168.0.1

Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
[wrap/rephrase commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-02-20 13:53:15 +09:00
Sungbo Eo
9968a909c2 Revert "ramips: increase spi-max-frequency for ipTIME mt7620 devices"
This reverts commit 13a185bf8a.

There was a report that one A1004ns device fails to detect its flash
chip correctly:

[    1.470297] spi-nor spi0.0: unrecognized JEDEC id bytes: e0 10 0c 40 10 08
[    1.484110] spi-nor: probe of spi0.0 failed with error -2

It also uses a different flash chip model:
* in my hand: Winbond W25Q128FVSIG (SOIC-8)
* reported: Macronix MX25L12845EMI-10G (SOP-16)

Reducing spi-max-frequency solved the detection failure. Hence revert.

Reported-by: Koasing <koasing@gmail.com>
Tested-by: Koasing <koasing@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-02-20 13:47:57 +09:00
Nick Hainke
2fd049f5cd ramips: add Ubiquiti EdgePoint R6 as alt name
The Ubiquiti EdgePoint R6 is identical to the EdgeRouter X SFP.
However, it fits well into outdoor environments due to its water-proven
case.

More specifications: 9715beb04c ("ramips: add support for Ubiquiti
EdgeRouter X-SFP")

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-02-19 17:26:37 +01:00
Felix Fietkau
918d4ab41e ramips: fix NAND flash driver ECC bit position mask
The bit position mask was accidentally made too wide, overlapping with the LSB
from the byte position mask. This caused ECC calculation to fail for odd bytes

Signed-off-by: Chad Monroe <chad.monroe@smartrg.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-02-16 21:26:27 +01:00
Chuanhong Guo
2f024b7933 ramips: mt7621: do memory detection on KSEG1
It's reported that current memory detection code occasionally detects
larger memory under some bootloaders.
Current memory detection code tests whether address space wraps around
on KSEG0, which is unreliable because it's cached.

Rewrite memory size detection to perform the same test on KSEG1 instead.
While at it, this patch also does the following two things:
1. use a fixed pattern instead of a random function pointer as the magic
   value.
2. add an additional memory write and a second comparison as part of the
   test to prevent possible smaller memory detection result due to
   leftover values in memory.

Fixes: 6d91ddf517 ("ramips: mt7621: add support for memory detection")
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-02-14 11:59:12 +08:00
John Audia
e9c1c83679 kernel: bump 5.10 to 5.10.98
Manually rebased:
	bcm27xx/patches-5.10/950-0675-drm-vc4-hdmi-Drop-devm-interrupt-handler-for-CEC-int.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <graysky@archlinux.us>
2022-02-11 23:17:40 +01:00
INAGAKI Hiroshi
337e942290 ramips: add support for ELECOM WRC-2533GS2
ELECOM WRC-2533GS2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB (NT5CC64M16GP-DI)
- Flash		: SPI-NOR 16 MiB (MX25L12835FM2I-10G)
- WLAN		: 2.4/5GHz 4T4R (2x MediaTek MT7615)
- Ethernet	: 10/100/1000 Mbps x5
  - Switch	: MediaTek MT7530 (SoC)
- LEDs/Keys	: 4x/6x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J4: 3.3V, GND, TX, RX from ethernet port side
  - 57600n8
- Power		: 12 VDC, 1.5 A

Flash instruction using factory image:

1. Boot WRC-2533GS2 normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing

MAC Addresses:

LAN	: 04:AB:18:xx:xx:FB (Factory, 0xFFF4 (hex))
WAN	: 04:AB:18:xx:xx:FC (Factory, 0xFFFA (hex))
2.4 GHz	: 04:AB:18:xx:xx:FD (Factory, 0x4    (hex))
5 GHz	: 04:AB:18:xx:xx:FE (Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-02-11 22:30:04 +09:00
INAGAKI Hiroshi
34a373c0df ramips: move MAC configs to device dts from wrc-gs-2pci.dtsi
The locations of MAC addresses in mtd for LAN/WAN on ELECOM WRC-2533GS2
are changed from the other WRC-GS/GST devices with 2x PCIe. So move the
related configurations in mt7621_elecom_wrc-gs-2pci.dtsi to dts of each
model.

- WRC-1750GS
- WRC-1750GSV
- WRC-1750GST2
- WRC-1900GST
- WRC-2533GST
- WRC-2533GST2

  -> LAN: 0xE000, WAN: 0xE006

- WRC-2533GS2

  -> LAN: 0xFFF4, WAN: 0xFFFA

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-02-11 22:30:04 +09:00
Sungbo Eo
cdc735de62 ramips: update WLAN MAC address of ipTIME A3004T
Reported MAC addresses:

| interface |    MAC address    |     source     | comment
|-----------|-------------------|----------------|---------
|       LAN | 90:xx:xx:18:xx:1F |                | [1]
|       WAN | 90:xx:xx:18:xx:1D |                |
|   WLAN 2G | 92:xx:xx:48:xx:1C |                |
|   WLAN 5G | 90:xx:xx:18:xx:1C | factory 0x4    |
|           | 90:xx:xx:18:xx:1C | config ethaddr |

[1] Used in this patch as WLAN 2G MAC address with the local bit set

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-02-11 22:30:04 +09:00
Sungbo Eo
37753f34ac ramips: add support for ipTIME AX2004M
ipTIME AX2004M is an 802.11ax (Wi-Fi 6) router, based on MediaTek
MT7621A.

Specifications:
* SoC: MT7621A
* RAM: 256 MiB
* Flash: NAND 128 MiB
* Wi-Fi:
  * MT7915D: 2.4/5 GHz (DBDC)
* Ethernet: 5x 1GbE
  * Switch: SoC built-in
* USB: 1x 3.0
* UART: J4 (115200 baud)
  * Pinout: [3V3] (TXD) (RXD) (GND)

MAC addresses:

| interface |    MAC address    |     source     | comment
|-----------|-------------------|----------------|---------
|       LAN | 58:xx:xx:00:xx:9B |                | [1]
|       WAN | 58:xx:xx:00:xx:99 |                |
|   WLAN 2G | 58:xx:xx:00:xx:98 | factory 0x4    |
|   WLAN 5G | 5A:xx:xx:40:xx:98 |                |
|           | 58:xx:xx:00:xx:98 | config ethaddr |

[1] Used in this patch as WLAN 5G MAC address with the local bit set

Load addresses:
* stock
  * 0x80010000: FIT image
  * 0x81001000: kernel image -> entry
* OpenWrt
  * 0x80010000: FIT image
  * 0x82000000: uncompressed kernel+relocate image
  * 0x80001000: relocated kernel image -> entry

Notes:
* This device has a dual-boot partition scheme, but this firmware works
  only on boot partition 1. The stock web interface will flash only on the
  inactive boot partition, but the recovery web page will always flash on
  boot partition 1.

Installation via recovery mode:
1.  Press reset button, power up the device, wait >10s for CPU LED
    to stop blinking.
2.  Upload recovery image through the recovery web page at 192.168.0.1.

Revert to stock firmware:
1.  Install stock image via recovery mode.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-02-11 22:30:04 +09:00
DENG Qingfang
f9cfe7af1f kernel: backport MT7530 IRQ support
Support MT7530 PHY link change interrupts, and enable for MT7621.

For external MT7530, a GPIO IRQ line is required, which is
board-specific, so it should be added to each DTS. In case the
interrupt-controller property is missing, it will fall back to
polling mode.

Signed-off-by: DENG Qingfang <dqfext@gmail.com>
2022-02-10 13:44:06 +00:00
DENG Qingfang
73fd9f79ce
kernel: backport MediaTek Ethernet PHY driver
Add support for MediaTek Gigabit Ethernet PHYs found in MT7530 and
MT7531. Fix some link up/down issues.
The errornous check for the PHY mode which broke things with MT7531
has been removed as suggested by patch
 net: phy: mediatek: remove PHY mode check on MT7531
As a result, things are working fine now on MT7622+MT7531 as well.

Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-02-09 21:17:54 +00:00
Sungbo Eo
09f383465e ramips: move KERNEL_LOADADDR into Device/Default
Commit f4a79148f8 ("ramips: add support for ipTIME AX2004M") was
reverted due to KERNEL_LOADADDR leakage, and it seems the problem can be
mitigated by moving the variable definition into Device/Default. By this,
KERNEL_LOADADDR redefined in a device recipe will not be leaked into the
subsequent device recipes anymore and thus will remain as a per-device
variable.

Ref: cd6a6e3030 ("Revert "ramips: add support for ipTIME AX2004M"")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-02-08 23:23:53 +09:00
Raymond Wang
3343ca7e68 ramips: add support for Xiaomi Mi Router CR660x series
Xiaomi Mi Router CR6606 is a Wi-Fi6 AX1800 Router with 4 GbE Ports.
Alongside the general model, it has three carrier customized models:
CR6606 (China Unicom), CR6608 (China Mobile), CR6609 (China Telecom)

Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256MB DDR3 (ESMT M15T2G16128A)
- Flash: 128MB NAND (ESMT F59L1G81MB)
- Ethernet: 1000Base-T x4 (MT7530 SoC)
- WLAN: 2x2 2.4GHz 574Mbps + 2x2 5GHz 1201Mbps (MT7905DAN + MT7975DN)
- LEDs: System (Blue, Yellow), Internet (Blue, Yellow)
- Buttons: Reset, WPS
- UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1)
- Power: 12VDC, 1A

Jailbreak Notes:
1. Get shell access.
   1.1. Get yourself a wireless router that runs OpenWrt already.
   1.2. On the OpenWrt router:
      1.2.1. Access its console.
      1.2.2. Create and edit
             /usr/lib/lua/luci/controller/admin/xqsystem.lua
             with the following code (exclude backquotes and line no.):
```
     1  module("luci.controller.admin.xqsystem", package.seeall)
     2
     3  function index()
     4      local page   = node("api")
     5      page.target  = firstchild()
     6      page.title   = ("")
     7      page.order   = 100
     8      page.index = true
     9      page   = node("api","xqsystem")
    10      page.target  = firstchild()
    11      page.title   = ("")
    12      page.order   = 100
    13      page.index = true
    14      entry({"api", "xqsystem", "token"}, call("getToken"), (""),
103, 0x08)
    15  end
    16
    17  local LuciHttp = require("luci.http")
    18
    19  function getToken()
    20      local result = {}
    21      result["code"] = 0
    22      result["token"] = "; nvram set ssh_en=1; nvram commit; sed -i
's/channel=.*/channel=\"debug\"/g' /etc/init.d/dropbear; /etc/init.d/drop
bear start;"
    23      LuciHttp.write_json(result)
    24  end
```
      1.2.3. Browse http://{OWRT_ADDR}/cgi-bin/luci/api/xqsystem/token
             It should give you a respond like this:
             {"code":0,"token":"; nvram set ssh_en=1; nvram commit; ..."}
             If so, continue; Otherwise, check the file, reboot the rout-
             er, try again.
      1.2.4. Set wireless network interface's IP to 169.254.31.1, turn
             off DHCP of wireless interface's zone.
      1.2.5. Connect to the router wirelessly, manually set your access
             device's IP to 169.254.31.3, make sure
             http://169.254.31.1/cgi-bin/luci/api/xqsystem/token
             still have a similar result as 1.2.3 shows.
   1.3. On the Xiaomi CR660x:
        1.3.1. Login to the web interface. Your would be directed to a
               page with URL like this:
               http://{ROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/web/home#r-
               outer
        1.3.2. Browse this URL with {STOK} from 1.3.1, {WIFI_NAME}
               {PASSWORD} be your OpenWrt router's SSID and password:
               http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/misy-
               stem/extendwifi_connect?ssid={WIFI_NAME}&password={PASSWO-
               RD}
               It should return 0.
        1.3.3. Browse this URL with {STOK} from 1.3.1:
               http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/xqsy-
               stem/oneclick_get_remote_token?username=xxx&password=xxx&-
               nonce=xxx
   1.4. Before rebooting, you can now access your CR660x via SSH.
        For CR6606, you can calculate your root password by this project:
        https://github.com/wfjsw/xiaoqiang-root-password, or at
        https://www.oxygen7.cn/miwifi.
        The root password for carrier-specific models should be the admi-
        nistration password or the default login password on the label.
        It is also feasible to change the root password at the same time
        by modifying the script from step 1.2.2.
        You can treat OpenWrt Router however you like from this point as
        long as you don't mind go through this again if you have to expl-
        oit it again. If you do have to and left your OpenWrt router unt-
        ouched, start from 1.3.
2. There's no official binary firmware available, and if you lose the
   content of your flash, no one except Xiaomi can help you.
   Dump these partitions in case you need them:
   "Bootloader" "Nvram" "Bdata" "crash" "crash_log"
   "firmware" "firmware1" "overlay" "obr"
   Find the corespond block device from /proc/mtd
   Read from read-only block device to avoid misoperation.
   It's recommended to use /tmp/syslogbackup/ as destination, since files
   would be available at http://{ROUTER_ADDR}/backup/log/YOUR_DUMP
   Keep an eye on memory usage though.
3. Since UART access is locked ootb, you should get UART access by modify
   uboot env. Otherwise, your router may become bricked.
   Excute these in stock firmware shell:
    a. nvram set boot_wait=on
    b. nvram set bootdelay=3
    c. nvram commit
   Or in OpenWrt:
    a. opkg update && opkg install kmod-mtd-rw
    b. insmod mtd-rw i_want_a_brick=1
    c. fw_setenv boot_wait on
    d. fw_setenv bootdelay 3
    e. rmmod mtd-rw

Migrate to OpenWrt:
 1. Transfer squashfs-firmware.bin to the router.
 2. nvram set flag_try_sys1_failed=0
 3. nvram set flag_try_sys2_failed=1
 4. nvram commit
 5. mtd -r write /path/to/image/squashfs-firmware.bin firmware

Additional Info:
 1. CR660x series routers has a different nand layout compared to other
    Xiaomi nand devices.
 2. This router has a relatively fresh uboot (2018.09) compared to other
    Xiaomi devices, and it is capable of booting fit image firmware.
    Unfortunately, no successful attempt of booting OpenWrt fit image
    were made so far. The cause is still yet to be known. For now, we use
    legacy image instead.

Signed-off-by: Raymond Wang <infiwang@pm.me>
2022-02-07 00:03:27 +01:00
Hauke Mehrtens
1b311aab31 Revert "kernel: backport MediaTek Ethernet PHY driver"
This reverts commit 8b4cba53a9.

This broke the mt7530 on Linksys e8450 (mt7622) for me.
[    1.312943] mt7530 mdio-bus:00 lan1 (uninitialized): failed to connect to PHY: -EINVAL
[    1.320890] mt7530 mdio-bus:00 lan1 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 0
[    1.331163] mt7530 mdio-bus:00 lan2 (uninitialized): failed to connect to PHY: -EINVAL
[    1.339085] mt7530 mdio-bus:00 lan2 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 1
[    1.349321] mt7530 mdio-bus:00 lan3 (uninitialized): failed to connect to PHY: -EINVAL
[    1.357241] mt7530 mdio-bus:00 lan3 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 2
[    1.367452] mt7530 mdio-bus:00 lan4 (uninitialized): failed to connect to PHY: -EINVAL
[    1.375367] mt7530 mdio-bus:00 lan4 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 3
[    1.385750] mt7530 mdio-bus:00 wan (uninitialized): failed to connect to PHY: -EINVAL
[    1.393575] mt7530 mdio-bus:00 wan (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 4

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-02-05 19:13:19 +01:00
Hauke Mehrtens
781f2f7300 Revert "kernel: backport MT7530 IRQ support"
This reverts commit 3f4301e123.

This broke the mt7530 on Linksys e8450 (mt7622) for me.
[    1.300554] mt7530 mdio-bus:00: no interrupt support

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-02-05 19:13:15 +01:00
DENG Qingfang
3f4301e123 kernel: backport MT7530 IRQ support
Support MT7530 PHY link change interrupts, and enable for MT7621.

Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-02-05 17:46:59 +02:00
DENG Qingfang
8b4cba53a9 kernel: backport MediaTek Ethernet PHY driver
Add support for MediaTek Gigabit Ethernet PHYs found in MT7530.
Fix some link up/down issues.

Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-02-05 17:46:59 +02:00
Sven Eckelmann
7c3efd5273 ramips: Switch Teltonika RUT5xx to kernel GPIO-line watchdog driver
The commit 04e91631e0 ("om-watchdog: add support for Teltonika RUT5xx
(ramips)") used the deprecated om-watchdog daemon to handle the GPIO-line
connected watchdog on the Teltonika RUT5xx.

But this daemon has massive problems since commit 30f61a34b4
("base-files: always use staged sysupgrade"). The process will always be
stopped on sysupgrades. If the sysupgrade takes slightly longer, the
watchdog is not triggered at the correct time and thus the sysupgrade will
interrupted hard by the watchdog sysupgrade. And this hard interrupt can
easily brick the device when there is no fallback (dual-boot, ...).

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-02-03 22:27:15 +01:00
Stijn Tintel
cd6a6e3030 Revert "ramips: add support for ipTIME AX2004M"
Commit f4a79148f8 ("ramips: add support for ipTIME AX2004M") seems to
leak KERNEL_LOADADDR 0x82000000 to other devices, causing the to no
longer boot. The leak is visible in u-boot:

   Using 'config-1' configuration
   Trying 'kernel-1' kernel subimage
     Description:  MIPS OpenWrt Linux-5.10.92
     Type:         Kernel Image
     Compression:  lzma compressed
     Data Start:   0x840000e4
     Data Size:    10750165 Bytes = 10.3 MiB
     Architecture: MIPS
     OS:           Linux
     Load Address: 0x82000000
     Entry Point:  0x82000000

Normally, it should look like this:

   Using 'config-1' configuration
   Trying 'kernel-1' kernel subimage
     Description:  MIPS OpenWrt Linux-5.10.92
     Type:         Kernel Image
     Compression:  lzma compressed
     Data Start:   0xbfca00e4
     Data Size:    2652547 Bytes = 2.5 MiB
     Architecture: MIPS
     OS:           Linux
     Load Address: 0x80001000
     Entry Point:  0x80001000

Revert the commit to avoid more people soft-bricking their devices.

This reverts commit f4a79148f8.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-02-01 21:35:15 +02:00
Davide Fioravanti
8fde82095b ramips: add support for Wavlink WL-WN535K1
The Wavlink WL-WN535K1 is a "mesh" router with 2 gigabit ethernet ports
and one fast ethernet port. Mine is branded as Talius TAL-WMESH1.
It can be found in kits of 2 or 3 (WL-WN535K2 or WL-WN535K3).
The motherboard is labelled as WS-WN535G3-B-V1.2 so this image could
potentially work for WL-WN535G3R and WS-WN535G3R with little to none
effort, but it's untested.

Hardware
--------
SoC:   Mediatek MT7620A
RAM:   64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CS)
ETH:
  - 2x 10/100/1000 Mbps Ethernet (RTL8211F)
  - 1x 10/100 Mbps Ethernet (integrated in SOC)
WIFI:
  - 2.4GHz: 1x (integrated in SOC) (2x2:2)
  - 5GHz:   1x MT7612E (2x2:2)
  - 4 internal antennas
BTN:
  - 1x Reset button
  - 1x Touchlink button (set to WPS)
  - 1x ON/OFF switch
LEDS:
  - 1x Red led (system status)
  - 1x Blue led (system status)
  - 3x Green leds (ethernet port status/act)
UART:
  - 57600-8-N-1

Everything works correctly.

Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.

Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on WN535K1_V1510_200916 firmware version.

1) Go to http://192.168.10.1/webcmd.shtml

2) Type the following line in the "Command" input box and then press enter:
	mkdir /etc_ro/lighttpd/www/dev; dd if=/dev/mtd0ro of=/etc_ro/lighttpd/www/dev/mtd0ro

3) After few seconds in the textarea should appear this output:
		16384+0 records in
	16384+0 records out

   If your output doesn't match mine, stop reading and ask for
   help in the forum.

4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the
   content of the whole NOR. If the file size is 0 byte, stop reading
   and ask for help in the forum.

5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type:
	rm /etc_ro/lighttpd/www/dev/mtd0ro;for i in 1 2 3 4 5; do dd if=/dev/mtd${i}ro of=/etc_ro/lighttpd/www/dev/mtd${i}ro; done

6) After few seconds, in the textarea should appear this output:
		384+0 records in
	384+0 records out
	128+0 records in
	128+0 records out
	128+0 records in
	128+0 records out
	14720+0 records in
	14720+0 records out
	1024+0 records in
	1024+0 records out

   If your output doesn't match mine, stop reading and ask for
   help in the forum.

7) Open the following links to download the partitions of the OEM FW:
	http://192.168.10.1/dev/mtd1ro
	http://192.168.10.1/dev/mtd2ro
	http://192.168.10.1/dev/mtd3ro
	http://192.168.10.1/dev/mtd4ro
	http://192.168.10.1/dev/mtd5ro

   If one (or more) of these files are 0 byte, stop reading and ask
   for help in the forum.

8) Store these downloaded files in a safe place.

9) Reboot your router to remove any temporary file in ram.

Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update_mesh.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.

Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Notes
-----
1) Router mac addresses:
   LAN		XX:XX:XX:XX:XX:E2 (factory @ 0x28)
   WAN		XX:XX:XX:XX:XX:E3 (factory @ 0x2e)
   WIFI 2G	XX:XX:XX:XX:XX:E4 (factory @ 0x04)
   WIFI 5G	XX:XX:XX:XX:XX:E5 (factory @ 0x8004)

   LABEL	XX:XX:XX:XX:XX:E5

2) The OEM firmware upgrade page accepts only files containing the
   string "WN535K1" in the filename.

3) Additional notes 1,2,3 in the WS-WN583A6 commit are still valid
(92780d80ab)

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[remove trailing whitespace]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-30 01:15:23 +09:00
Sungbo Eo
f4a79148f8 ramips: add support for ipTIME AX2004M
ipTIME AX2004M is an 802.11ax (Wi-Fi 6) router, based on MediaTek
MT7621A.

Specification:
* SoC: MT7621A
* RAM: 256 MiB
* Flash: NAND 128 MiB
* Wi-Fi:
  * MT7915D: 2.4/5 GHz (DBDC)
* Ethernet: 5x 1GbE
  * Switch: SoC built-in
* USB: 1x 3.0
* UART: J4 (115200 baud)
  * Pinout: [3V3] (TXD) (RXD) (GND)

MAC address:

| interface |        MAC        |     source     | comment
|-----------|-------------------|----------------|---------
|       LAN | 58:XX:XX:00:XX:9B |                | [1]
|       WAN | 58:XX:XX:00:XX:99 |                |
|   WLAN 2G | 58:XX:XX:00:XX:98 | factory 0x4    |
|   WLAN 5G | 5A:XX:XX:40:XX:98 |                |
|           |                   |                |
|           | 58:XX:XX:00:XX:98 | config ethaddr |

[1] Used in this patch as WLAN 5G MAC address with the local bit set

Load address:
* stock
  * 0x80010000: FIT image
  * 0x81001000: kernel image -> entry
* OpenWrt
  * 0x80010000: FIT image
  * 0x82000000: uncompressed kernel+relocate image
  * 0x80001000: relocated kernel image -> entry

Installation via **recovery** mode:
1.  Press reset button, power up the device, wait >10s for CPU LED
    to stop blinking.
2.  Upload recovery image through the recovery web page at 192.168.0.1.

Revert to stock firmware:
1.  Install stock image via recovery mode.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Sungbo Eo
03aa57d7ab ramips: make the relocation address configurable
If no argument is given to relocate-kernel, KERNEL_LOADADDR will be used
just as before.

This is a preparation for ramips support of ipTIME AX2004M.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Stijn Tintel
a47f152943 ramips: enable I2C_CHARDEV in mt7621/config-5.10
I2C_CHARDEV used to be enabled in mt7621/config-5.4. Enable it in the
5.10 config, as it's required for PoE control on Unifi Switch Flex.

Fixes: b4aad29a1d ("ramips: add support for kernel 5.10")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-01-28 19:03:52 +02:00
Chuanhong Guo
c06482489d kernel: 5.10: drop broken-flash-reset patch
Flash accessing instruction templates are determined during probe since
v5.6 for spimem-dirmap support in spi-nor driver in upstream commit:
df5c21002cf4 ("mtd: spi-nor: use spi-mem dirmap API")
As a result, changing bus_width on the fly doesn't work anymore and this
patch will cause executing spi-mem ops with 3-byte address on 16-32M
flash area.
We can't easily revert that behavioral change upstream so drop the patch
to prevent u-boot and eeprom from being erased.

Fixes: b10d604459("kernel: add linux 5.10 support")
Reported-by: Frank Di Matteo <dimatto@foxmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-01-28 21:03:10 +08:00
Rodrigo Araujo
7c8ade1765 ramips: correct vendor name for COMFAST/Joowin
When Joowin WR758AC V1 and V2 devices were added, they should have been
added with the primary manufacturer name which is COMFAST, since Joowin
is just an alternate vendor name on some coutries or stores.

Fix this by changing the the vendor name on the respective files and set
Joowin as ALT0 variants while ensuring compatibility for early users.
Also adjust the model names to better follow the naming rules.

As a side effect, fix mt76x8 network script which was left incorrectly
unsorted on the case block conditions.

Fixes: 766733e172 ("ramips: add support for Joowin WR758AC V1 and V2")
Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
2022-01-22 01:17:04 +01:00
David Bauer
ef5f3eb700 ramips: read Tenbay T-MB5EU address from single location
Currently the WAN MAC address is read from a different offset contrary
to all other addresses.

There's conflicting information whether offset 0x28 on the factory
partition contains the valid WAN mac for all devices while 0x4 seems to
be uniform.

Read the WAN mac from this location and calculate it.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-01-22 01:16:56 +01:00
David Bauer
b0c04a37e4 ramips: update Tenbay T-MB5EU wireless MAC address
The current MAC address assignment is still incorrect.

Use the same MAC address as seen on the stock firmware
for both wireless interfaces.

The 5GHz MAC address OUI is +2 in the first EUI octet. We currently
don't do this in OpenWrt. Ignore this offset for now. With the current
assignment, recurring MAC addresses between radios is already taken care
of.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-01-22 01:16:49 +01:00
Rui Salvaterra
61e58f7cec kernel: bump 5.10 to 5.10.92
Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-01-16 20:51:14 +01:00
Michael Pratt
74516f4357 ramips: fix reboot for remaining 32 MB boards
The following devices have a Winbond W25Q256FV flash chip,
which does not have the RESET pin enabled by default,
and otherwise would require setting a bit in a status register.

Before moving to Linux 5.4, we had the patch:
0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch
which kept specific flash chips with explicit 3-byte and 4-byte address modes
to stay in 3-byte address mode while idle (after an erase or write)
by using a custom flag SPI_NOR_4B_READ_OP that was part of the patch.

this was obsoleted by the patch:
481-mtd-spi-nor-rework-broken-flash-reset-support.patch
which uses the newer upstream flag SNOR_F_BROKEN_RESET
for devices with a flash chip that cannot be hardware reset with RESET pin
and therefore must be left in 3-byte address mode when idle.

The new patch requires that the DTS of affected devices
have the property "broken-flash-reset", which was not yet added for most of them.

This commit adds the property for remaining affected devices in ramips target,
specifically because of the flash chip model.

However, it is possible that there are other devices
where the flash chip uses an explicit 4-byte address mode
and the RESET pin is not connected to the SOC on the board,
and those DTS would also need this property.

Ref: 22d982ea00 ("ramips: add support for switching between 3-byte and 4-byte addressing")
Ref: dfa521f129 ("generic: spi-nor: rework broken-flash-reset")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-01-15 17:12:12 +01:00
SeongUk Moon
9c8ccdcdc8 ramips: add support for ipTIME A6004NS-M
ipTIME A6004NS-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A.

Specifications:
- SoC: MediaTek MT7621A (880MHz, Duel-Core)
- RAM: DDR3 256MB
- Flash: SPI NOR 16MB (Winbond W25Q128BV)
- WiFi: MediaTek MT7615E (2.4GHz, 5GHz)
- Ethernet: MediaTek MT7530 (WAN x1, LAN x4, SoC built-in Estimated)
- USB: USB 3.0 x1
- UART: [3.3V, TX, RX, GND] (57600 8N1)

Installation via web interface:
1. Flash initramfs image using OEM's Firmware Update page.
2. Connect to OpenWrt with an SSH connection to `192.168.1.1`.
3. Perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Flash stock firmware via OEM's Recovery mode

How to use OEM's Recovery mode:
1. Power on the device and connect the shell through UART.
2. Connect to the shell and press the `t` key on the keyboard.
3. Set fixed IP with  `192.168.0.2`  with subnet mask  `255.255.255.0`
4. Flash image via TFTP to  `192.168.0.1`

Additional Notes:
1. The higher the 5Ghz Frequency, the lower the stability. It is recommended to use less than 5.775Ghz.
2. If the 5Ghz frequency is too high, 5Ghz may not work.
3. A6ns-M use shared dtsi file of A6004NS-M. (reference: /mt7621_iptime_a6004ns-m.dtsi).

Signed-off-by: SeongUk Moon <antegral@antegral.net>
[convert CRLF to LF]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-15 20:43:14 +09:00
Kyoungkyu Park
6041c693dd ramips: add support for HUMAX E2
HUMAX E2 (also known as HUMAX QUANTUM E2) is a 2.4/5GHz band AC router,
based on MediaTek MT7620A.

Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB (MXIC MX25L6405D)
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7610E
- Ethernet: 1x 10/100Mbps
  - Switch: SoC internal
- UART: J2 (57600 8N1)
  - pinout: [3V3] (RXD) (GND) (TXD)

Installation and Recovery via TFTP:
1. Connect ethernet cable between Router port and PC Ethernet port.
2. Set your computer to a static IP **192.168.1.1**
3. Turn the device off and wait a few seconds. Hold the WPS button on front
   of device and insert power.
4. Send a firmware image to **192.168.1.6** using TFTP.
   You can use any TFTP client. (tftp, curl, Tftpd64...)
5. Wait until Power LED stop flashing. **DO NOT TURN OFF DEVICE!**
   The device will be automatically rebooted.

Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space>
2022-01-15 20:05:46 +09:00
Felix Fietkau
83b14ec026 ramips: enable badblock table support on linksys ea7xxx devices
Use remapping only on the kernel partitions.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Felix Fietkau
3c78fabb0d ramips: mt7621_nand: fix writing upper half of fdm data
Since the loop iterates from 0-3, subtracting 4 from the shift
multiplier does not make any sense

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-01-13 18:33:06 +01:00
Oskari Lemmela
fdda3130f2 mikrotik: make soft_config writable
Parent mtd partition needs to be writable

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2022-01-13 09:33:29 +01:00
Oskari Lemmela
8441a622ec mikrotik: enable variable size erase
Add support for variable size erase blocks.
Enable it to all targets which has mikrotik targets.

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2022-01-13 09:33:29 +01:00
Nick McKinney
e0a574d4b7 ramips: add support for Linksys EA6350 v4
Specifications:
- SoC: MT7621DAT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 128 MB NAND
- Ethernet: 5x 1GiE MT7530
- WiFi: MT7603/MT7613
- USB: 1x USB 3.0

This is another MT7621 device, very similar to other Linksys EA7300
series devices.

Installation:

Upload the generated factory.bin image via the stock web firmware
updater.

Reverting to factory firmware:

Like other EA7300 devices, this device has an A/B router configuration
to prevent bricking.  Hard-resetting this device three (3) times will
put the device in failsafe (default) mode.  At this point, flash the
OEM image to itself and reboot.  This puts the router back into the 'B'
image and allows for a firmware upgrade.

Troubleshooting:

If the firmware will not boot, first restore the factory as described
above.  This will then allow the factory.bin update to be applied
properly.

Signed-off-by: Nick McKinney <nick@ndmckinney.net>
2022-01-08 00:49:59 +01:00
Liangkuan Yang
bc7d36ba3a ramips: add support for RAISECOM MSG1500 X.00
RAISECOM MSG1500 X.00 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router.
Apart from the general model, there are two ISP customized models:
China Mobile and China Telecom.

Specifications:

- SoC: Mediatek MT7621AT
- RAM: 256MiB DDR3
- Flash: 128MiB NAND
- Ethernet: 5 * 10/100/1000Mbps: 4 * LAN + 1 * WAN
  - Switch: MediaTek MT7530 (SoC)
- WLAN: 1 * MT7615DN Dual-Band 2.4GHz 2T2R (400Mbps) 5GHz 2T2R (867Mbps)
- USB: 1 * USB 2.0 port
- Button: 1 * RESET button, 1 * WPS button, 1 * WIFI button
- LED: blue color: POWER, WAN, WPS, 2.4G, 5G, LAN1, LAN2, LAN3, LAN4, USB
- UART: 1 * serial port header (4-pin)
- Power: DC 12V, 1A
  - Switch: 1 * POWER switch

MAC addresses as verified by vendor firmware:

use   address             source
LAN   C8:XX:XX:3A:XX:E7   Config   "protest_lan_mac"  ascii  (label)
WAN   C8:XX:XX:3A:XX:EA   Config   "protest_wan_mac"  ascii
5G    C8:XX:XX:3A:XX:E8   Factory  "0x4"              hex
2.4G  CA:XX:XX:4A:XX:E8   [not on flash]

The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:

       5g                 2.4g         increment
 C8:XX:XX:90:XX:C3  CA:XX:XX:C0:XX:C3  0x30
 C8:XX:XX:3A:XX:08  CA:XX:XX:4A:XX:08  0x10
 C8:XX:XX:3A:XX:E8  CA:XX:XX:4A:XX:E8  0x10

Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.

Notes:

1. The vendor firmware allows you to connect to the router by telnet.
   (known version 1.0.0 can open telnet.)
   There is no official binary firmware available.
   Backup the important partitions data:
   "Bootloader", "Config", "Factory", and "firmware".
   Note that with the vendor firmware the memory is detected only 128MiB
   and the last 512KiB in NAND flash is not used.

2. The POWER LED is default on after press POWER switch.
   The WAN and LAN1 - 4 LEDs are wired to ethernet switch.
   The WPS LED is controlled by MT7615DN's GPIO.
   Currently there is no proper way to configure it.

3. At the time of adding support the wireless config needs to be set up
   by editing the wireless config file:

 * Setting the country code is mandatory, otherwise the router loses
   connectivity at the next reboot. This is mandatory and can be done
   from luci. After setting the country code the router boots correctly.
   A reset with the reset button will fix the issue and the user has to
   reconfigure.

 * This is minor since the 5g interface does not come up online although
   it is not set as disabled. 2 options here:

   1- Either run the "wifi" command. Can be added from LuCI in system -
      startup - local startup and just add wifi above "exit 0".

   2- Or add the serialize option in the wireless config file as shown
      below. This one would work and bring both interfaces automatically
      at every boot:

      config wifi-device 'radio0'
          option serialize '1'

      config wifi-device 'radio1'
          option serialize '1'

Flash instructions using initramfs image:

1. Press POWER switch to power down if the router is running.

2. Connect PC to one of LAN ports, and set
   static IP address to "10.10.10.2", netmask to "255.255.255.0",
   and gateway to "10.10.10.1" manually on the PC.

3. Push and hold the WIFI button, and then power up the router.
   After about 10s (or you can call the recovery page, see "4" below)
   you can release the WIFI button.
   There is no clear indication when the router
   is entering or has entered into "RAISECOM Router Recovery Mode".

4. Call the recovery page for the router at "http://10.10.10.1".
   Keep an eye on the "WARNING!! tip" of the recovery page.
   Click "Choose File" to select initramfs image, then click "Upload".

5. If image is uploaded successfully, you will see the page display
   "Device is upgrading the firmware... %".
   Keep an eye on the "WARNING!! tip" of the recovery page.
   When the page display "Upgrade Successfully",
   you can set IP address as "automatically obtain".

6. After the rebooting (PC should automatically obtain an IP address),
   open the SSH connection, then download the sysupgrade image
   to the router and perform sysupgrade with it.

Flash back to vendor firmware:

 See "Flash instructions 1 - 5" above.
 The only difference is that in step 4
 you should select the vendor firmware which you backup.

Signed-off-by: Liangkuan Yang <ylk951207@gmail.com>
2022-01-08 00:49:59 +01:00
Rodrigo Araujo
766733e172 ramips: add support for Joowin WR758AC V1 and V2
This commit adds support for Joowin (aka Comfast) WR758AC V1 and V2
devices.

Both have the same wall AP/repeater form factor and differ only
in the 5Ghz chipset (V1 has MT7662, V2 has MT7663).

OpenWrt developers forum page:
https://forum.openwrt.org/t/87355

Specifications:

 - CPU: MediaTek MT7628AN (580MHz)
 - Flash: 8MB
 - RAM: 64MB DDR2
 - 2.4 GHz: 802.11b/g/n (MT7603)
 - 5 GHz: 802.11ac (V1 has MT7662, V2 has MT7663)
 - Antennas: 4x external single band antennas
 - LAN: 1x 10/100M
 - LED: Wifi 3x blue. Programmable
 - Button: WPS

MAC addresses as verified by OEM firmware:

use address source
LAN *:83 factory 0xe000
2g *:85 factory 0x4
5g *:86 factory 0x8004

How to install:
1- Setup a TFTP server on a machine with IP address 192.168.1.10/24
2- Name the image as `firmware_auto.bin` and place it on the root of the
TFTP server
3- Connect the device via Ethernet, it should pick and flash the image

Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
2022-01-08 00:49:59 +01:00
Shiji Yang
86d019d116 ramips: add ASUS RT-AC1200GU as alt name
RT-AC57U and RT-AC1200GU are the same models sold in different countries.
The purpose of this commit is to allow users to easily find the
corresponding firmware through the model number on the device label.

More specifications: 14e0e4f138 ("ramips: add support for ASUS RT-AC57U")

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[reword commit title/message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-02 01:31:02 +09:00
Sungbo Eo
a1deab0ec9 ramips: add support for ipTIME T5004
ipTIME T5004 is a 5-port Gigabit Ethernet router, based on MediaTek MT7621A.

Specifications:
* SoC: MT7621AT
* RAM: 128 MiB
* Flash: NAND 128 MiB
* Ethernet: 5x 1GbE
  * Switch: SoC built-in
* UART: J4 (57600 baud)
  * Pinout: [3V3] (TXD) (RXD) (GND)

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware via recovery mode:
1.  Press reset button, power up the device, wait >15s for CPU LED
    to stop blinking.
2.  Upload stock image to TFTP server at 192.168.0.1.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-02 00:50:43 +09:00
WonJung Kim
2dde2416e1 ramips: add support for ipTIME A3004T
ipTIME A3004T is a 2.4/5GHz band router, based on Mediatek MT7621.

Specifications:
 - SoC: MT7621 (880MHz)
 - RAM: DDR3 256M
 - Flash: NAND 128MB  (Macronix NAND 128MiB 3,3V 8-bit)
 - WiFi:
   - 2.4GHz: MT7615E
   - 5GHz : MT7615E
 - Ethernet:
   - 4x LAN
   - 1x WAN
 - USB: 1 * USB3.0 port
 - UART:
   - 3.3V, TX, RX, GND / 57600 8N1

Installation via web interface:
 1. Flash initramfs image using OEM's Recovery mode
 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
 - Flash stock firmware via OEM's Recovery mode

How to use OEM's Recovery mode:
 1. Power up with holding down the reset key until CPU LED stop blinking.
 2. Set fixed ip with `192.168.0.2` with subnet mask `255.255.255.0`
 3. Flash image via tftp to `192.168.0.1`

Additional Notes:
 This router shares one MT7915E chip for both 2.4Ghz/5Ghz.
 radio0 will not working on 5Ghz as it's not connected to the antenna.

Signed-off-by: WonJung Kim <git@won-jung.kim>
(added led dt-bindings)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-29 20:35:57 +01:00
Sungbo Eo
482a7e23a4 ramips: add support for WeVO AIR DUO
WeVO AIR DUO is a 1-bay NAS & 802.11ac (Wi-Fi 5) router, based on
MediaTek MT7620A.

Specifications:
* SoC: MT7620A
* RAM: 64 MiB
* Flash: SPI NOR 16 MiB
* USB & SATA bridge controller: JMicron JMS567
  * SATA 6Gb/s: 2.5" drive slot
  * USB 3.0: Micro-B
  * USB 2.0: connected to SoC
* Wi-Fi:
  * 2.4 GHz: SoC built-in
  * 5 GHz: MT7612EN
* Ethernet: 5x 1GbE
  * Switch: MT7530WU
* UART: 4-pin 1.27 mm pitch through-hole (57600 baud)
  * Pinout: (3V3)|(RXD) (TXD) (GND)

Notes:
* The drive is accessible through the external USB port only when the
  router is turned off.

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
    The image filename should have ".upload" extension.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-29 20:35:57 +01:00
David Bauer
00b194871c ramips: aw9523: add can_sleep flag for GPIO chip
The GPIO expander is connected via I2C, thus the can_sleep flag has to
be set to true. This should fix spurious "scheduling while atomic" bugs
in the kernel ringbuffer.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-29 03:43:03 +01:00
David Bauer
b1d483b865 ramips: work around duplicate MAC address on U6 Lite
The UniFi 6 Lite has two MAC addresses for the 2.4 and 5GHz radio in
it's EEPROM partition.

On my unit these are

F4 92 BF A0 BB 6F
F6 92 BF A0 BB 6F

The problem with these is that mac80211 increases the first octet by
2, which leads to conflicting MAC addresses between radios.

Work around this problem for now by increasing the last octet by 1 on
the 5 GHz radio.

Ubiquiti increases the last octet by 2 for each subsequent VAP created
per radio. Ideally we should do the same, however this functionality is
currently lacking from mac80211.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-20 00:12:12 +01:00
Sergey Ryazanov
fa3690f8f1 kernel: 5.10: consolidate mac80211 crypto options
Each of
- CRYPTO_AEAD2
- CRYPTO_AEAD
- CRYPTO_GF128MUL
- CRYPTO_GHASH
- CRYPTO_HASH2
- CRYPTO_HASH
- CRYPTO_MANAGER2
- CRYPTO_MANAGER
- CRYPTO_NULL2

either directly required for mac80211 crypto support, or directly
selected by such options. Support for the mac80211 crypto was enabled in
the generic config since c7182123b9 ("kernel: make cryptoapi support
needed by mac80211 built-in"). So move the above options from the target
configs to the generic config to make it clear why do we need them.

CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-17 16:16:34 +01:00
Sergey Ryazanov
b61ab8f57e kernel: filter out both Clang and LLD versions
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-17 16:16:34 +01:00
Sungbo Eo
cc3e390a74 ramips: mt7620: tidy up 02_network
* fix alphabetic sorting
* consolidate duplicate cases

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-16 22:28:58 +09:00
Rui Salvaterra
c772783394 ramips: remove Linux 5.4 support
We're at 5.10 stable, this can finally go.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-12-15 09:40:03 +00:00
David Bauer
07452a680b ramips: fix Tenbay T-MB5EU v1 Wireless MAC
It was reported, that Tenbay T-MB5EU v1 do have incorrect Wireless MAC
address set on 2.4 and 5 GHz.

Some boards do not seem to have the correct MAC address set for the
external PHY of the MT7915 radio at caldata offset 0xa.

As the external PHY does not expose a DT binding (yet), fix up the mac
address in userspace.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-12-15 00:13:40 +01:00
Rui Salvaterra
66f9ed1684 ramips: switch to kernel 5.10
Tested on mt7621 (Redmi AC2100) and running stable for several months.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2021-12-13 19:36:52 +01:00
Pawel Dembicki
794e8123ce ramips: mt7620: use OKLI loader with Jboot devices
Jboot devices have problem with >2MB kernelsize. The only way to avoid
this problem is use small loader.

This patch switch all mt7620 Jboot devices to lzma OKLI loader.

Suggested-by: Szabolcs Hubai <szab.hu@gmail.com>
Co-authored-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-12-13 19:36:10 +01:00
John Audia
6c945fa379 kernel: bump 5.10 to 5.10.83
Removed upstreamed:
    bcm53xx/patches-5.10/033-v5.16-0024-ARM-dts-BCM5301X-Fix-I2C-controller-interrupt.patch[1]
    bcm53xx/patches-5.10/033-v5.16-0025-ARM-dts-BCM5301X-Add-interrupt-properties-to-GPIO-no.patch[2]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.83&id=b2cd6fdcbe0a5cb44e4610a08cc58261d494a885
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.83&id=9db1d4a3c2700e1cc84c3d61199411d75c2a3ec6

Build system: x86_64*
Build-tested: bcm2711/RPi4B, ipq806x/R7800†
Run-tested: bcm2711/RPi4B, ipq806x/R7800†

* Had to revert 7c99085bd6 in order to build
  (latest bump of ca-certificates)

† Had to revert 7f1edbd412 in order to build
  (binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149)

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-12 21:11:30 +01:00
Kyoungkyu Park
9a1b9a42b7 ramips: add support for HUMAX E10
HUMAX E10 (also known as HUMAX QUANTUM E10) is a 2.4/5GHz band AC router,
based on MediaTek MT7621A.

Specifications:
- SoC: MT7621A
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB (MXIC MX25L12805D)
- WiFi:
  - 2.4GHz: MT7615
  - 5GHz: MT7615
- Ethernet: 2x 10/100/1000Mbps
  - Switch: SoC internal
- USB: 1x USB 2.0 Type-A
- UART: J1 (57600 8N1)
  - pinout: [3V3] (RXD) (GND) (TXD)

Installation via web interface:
- Flash **factory** image through the stock web interface.

Recovery procedure:
1. Connect ethernet cable between Router **LAN** port and PC Ethernet port.
2. Set your computer to a static IP **192.168.1.1**
3. Turn the device off and wait a few seconds. Hold the WPS button on front
   of device and insert power.
4. Send a firmware image to **192.168.1.6** using TFTP.
   You can use any TFTP client. (tftp, curl, Tftpd64...)
- It can accept both images which is
  HUMAX stock firmware dump (0x70000-0x1000000) image
  and OpenWRT **sysupgrade** image.

Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space>
[remove trailing whitespace]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-12 20:33:19 +09:00
Sungbo Eo
91e37b60a0 ramips: mt76x8: tidy up 02_network
* fix alphabetic sorting
* consolidate duplicate cases

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-12 20:25:56 +09:00
Sergey Ryazanov
7e89421a7c ramips: add support for Zbtlink ZBT-WG1602
Zbtlink ZBT-WG1602 is a Wi-Fi router intendent to use with WWAN
(UMTS/LTE/3G/4G) modems. The router board offsers a couple of miniPCIe
slots with USB and SIM only and another one pure miniPCIe slot as well
as five Gigabit Ethernet ports (4xLAN + WAN).

Specification:

* SoC: MT7621A
* RAM: 256/512 MiB
* Flash: 16/32 MiB (SPI NOR)
* external watchdog (looks like Torexsemi XC6131B)
* Eth: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
* WLAN 2GHz: MT7603EN (.11n, MIMO 2x2)
* WLAN 5GHz: MT7612EN (.11ac, MIMO 2x2)
* WLAN Ants: detachable x2, shared by 2GHz & 5GHz radios
* miniPCIe: 2x slots with USB&SIM + 1x slot with regular PCIe bus
* WWAN Ants: detachable x4
* External storage: microSD (SDXC) slot
* USB: 2.0 Type-A port
* LED: 11 (5 per Eth phy, 3 SoC controlled, 2 WLAN 2/5 controlled, 1
       power indicator)
* Button: 1 (reset)
* UART: console (115200 baud)
* Power: DC jack (12 V / 2.5 A)

Additional HW information:

* SoC USB port #1 is shared by internal miniPCIe slot and external
  Type-A USB port, USB D+/D- lines are toggled between ports using a
  GPIO controlled DPDT switch.
* Power of the USB enabled miniPCIe slots can be individually controlled
  using dedicated GPIO lines.
* Vendor firmware feeds the external watchdog with 1s pulses. GPIO
  watchdog driver is able to either generate a 1us pulses or toggle the
  output line. 1us is not enough for the external watchod timer, so
  the line toggling driver mode is utilized.

Installation:

Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can
be directly used to install OpenWrt. Firmware must be upgraded using the
'force' and 'do not save configuration' command line options (or
correspondig web interface checkboxes) since the vendor firmware is from
the pre-DSA era.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-05 18:49:14 +01:00
Yuchan Seo
c33eb0372e ramips: add support for ipTIME A3004NS-dual
ipTIME A3004NS-dual is a 2.4/5GHz band router, based on Mediatek MT7621.

Specifications:
- SoC: MT7621 (880MHz)
- RAM: DDR3 256M
- Flash: SPI NOR 16MB
- WiFi:
 - 2.4GHz: MT7602E
 - 5GHz : MT7612E
- Ethernet:
 - 4x LAN
 - 1x WAN
- USB: 1 * USB3.0 port
- UART:
  - 3.3V, TX, RX, GND / 57600 8N1

Installation via web interface:
- 1. Flash Initramfs image using OEM Firmware's web GUI
- 2. Boot into OpenWrt and perform Sysupgrade with sysupgrade image.

Revert to stock firmware:
- 1. Boot into OpenWrt and perform Sysupgrade with OEM Stock Firmware image.

Signed-off-by: Yuchan Seo <hexagonwin@disroot.org>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
2021-12-04 09:39:11 +09:00
Sergey V. Lobanov
e22c91e144 ramips: fix tl-mr3020-v3 switch topology to configure vlans via luci
Currently it is not possible to configure VLANs via LUCI on
tplink tl-mr3020-v3. This patch fixes switch topology for the
LUCI interface.

Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
[copied commit message from github PR]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-04 00:36:47 +01:00