According to SinoVoip up to 3A @ 3.3V are available for both
SFP modules together. Raise energy limit from 1W (default) to 3W,
however, be aware that using modules consuming more than 1W will
require active cooling!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
qrtr/ns.ko is now merged into qrtr/qrtr.ko, so drop the individual module packaging.
Fixes: f4989239cc ("kernel: bump 5.15 to 5.15.107")
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> #ipq807x/ax3600, x86_64/FW-7543B, mt7621/dap-x1860
upstream PR 408 improvements:
-Fix AMSDU packets unused
-Removed the ASMDU packets queue
-Add more info in the iw tool
-fix is_hw_crypto_enabled
-Optimization AMPDU_TX_OPERATIONAL (avoid a spinlock)
change to wongsyrone mod
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
`bzip2` is the standard executable for bzip2 compression
this includes development includes and both static and shared libs
(libbz2) which can be used by other packages
the initramfs generator offers the BZIP2 option but there was no
executable to support it, and worked only via side effect of having a
system-installed version of bzip2, which could be less predictable
Signed-off-by: Tony Butler <spudz76@gmail.com>
[ remove unintended change ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 394d7134ec.
The commit has unintentded change that cause compilation error with SDK
or LZO compression.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
QCA has finally sent a proper fixup for the 160MHz regression upstream,
so lets use the pending fix which also properly sets center frequency 2
in case 80+80 MHz is used.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Requires: tools/libdeflate
fix consistency of executable to use
`$(STAGING_DIR_HOST)/bin/libdeflate-gzip`, and not system-installed ones
from the usual environment `PATH`;
this affects option `CONFIG_KERNEL_INITRAMFS_COMPRESSION_GZIP`
this may have worked in the past but only via side effect of having the
binaries on the host system (and whatever unpredictable version or
patchset those might be), and did not use the improved but totally
compatible libdeflate-gzip
Fixes: 330bd380e8 ("image: allow building FIT and uImage with ramdisk")
Signed-off-by: Tony Butler <spudz76@gmail.com>
Requires: tools/bzip2
fix consistency of executable to use `$(STAGING_DIR_HOST)/bin/bzip2`, and
not system-installed ones from the usual environment `PATH`;
this affects option `CONFIG_KERNEL_INITRAMFS_COMPRESSION_BZIP2`
this may have worked in the past but only via side effect of having the
binaries on the host system (and whatever unpredictable version or
patchset those might be)
Fixes: 330bd380e8 ("image: allow building FIT and uImage with ramdisk")
Signed-off-by: Tony Butler <spudz76@gmail.com>
`bzip2` is the standard executable for bzip2 compression
this includes development includes and both static and shared libs
(libbz2) which can be used by other packages
the initramfs generator offers the BZIP2 option but there was no
executable to support it, and worked only via side effect of having a
system-installed version of bzip2, which could be less predictable
Signed-off-by: Tony Butler <spudz76@gmail.com>
Instead of erasing the entire NAND partition holding the kernel during
every system upgrade and then flashing a Yaffs file system image
prepared using kernel2minor (not accounting for bad blocks in the
process), use the Yafut utility to replace the kernel executable on
MikroTik NAND devices, preserving the existing Yaffs file system
(including bad block information) on the partition holding the kernel.
Add Yafut to DEFAULT_PACKAGES for the ath79/mikrotik target, so that the
tool is included in the initramfs images created when building for
multiple profiles. However, exclude Yafut from the images built for
MikroTik devices with NOR flash as the tool is currently only meant to
be used on devices with NAND flash.
As this addresses the concerns for MikroTik NAND devices discussed in
commit 9d96b6fb72 ("ath79/mikrotik: disable building NAND images"),
re-enable building images for these devices.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
Commit 9d96b6fb72 ("ath79/mikrotik: disable building NAND images")
disabled building images for MikroTik devices with NAND flash due to a
less than satisfactory method used for updating the kernel on those
devices back then.
To address the problem, add support for updating the kernel on MikroTik
devices with NAND flash using a new tool, Yafut, which enables copying
files from/to Yaffs file systems even if the kernel does not have native
support for the Yaffs file system compiled in. Instead of erasing the
entire NAND partition holding the kernel during every system upgrade
(which is what the previously-used approach employing kernel2minor
involved), Yafut preserves the Yaffs filesystem present on that
partition and only replaces the kernel executable. This allows bad
block information to be preserved across sysupgrade runs and also
enables wear leveling on the NAND partition holding the kernel. Yafut
does not rely on kernel2minor in any way and intends to eventually
supersede the latter for NAND devices.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
MEMREAD is a new ioctl for MTD character devices that was first included
in Linux 6.1. It allows userspace applications to use the Linux
kernel's OOB autoplacement mechanism while reading data from NAND
devices. The Yafut tool needs this ioctl to do its job.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
The ramdisk used by sysupgrade on MikroTik devices currently includes
U-Boot fw_* files that are not necessary for performing a system upgrade
on that platform. The relevant lines were added to
target/linux/ath79/mikrotik/base-files/lib/upgrade/platform.sh by commit
a66eee6336 ("ath79: add mikrotik subtarget"), likely because they also
existed in target/linux/ath79/nand/base-files/lib/upgrade/platform.sh,
where the platform_do_upgrade_mikrotik_nand() function moved by commit
a66eee6336 originally lived. However, these lines were added to
target/linux/ath79/nand/base-files/lib/upgrade/platform.sh by commit
55e6c903ae ("ath79: GL-AR300M: provide NAND support; increase to 4 MB
kernel"), which is not related to MikroTik devices in any way.
Remove the code adding unused U-Boot fw_* files to the ramdisk used by
sysupgrade on MikroTik devices.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
Alter the Aruba AP-105 image generation process so OpenWrt can be loaded
with the vendor Aruba APBoot.
This works by prepending the OpenWrt LZMA loader to the uImage and
jumping directly to the loader. Aruba does not offer bootm on these
boards.
This approach keeps compatibility to devices which had their U-Boot
replaced. Both bootloaders can boot the same image.
The same modification is most likely also possible for the Aruba AP-175.
With this patch, new installations do not require replacing the
bootloader and can be performed from the serial console without opening
the case.
Installation
------------
1. Attach to the serial console of the AP-105.
Interrupt autoboot and change the U-Boot env.
$ setenv apb_rb_openwrt "setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66;
netget 0x84000000 ap105.bin; go 0x84000040"
$ setenv apb_fb_openwrt "cp.b 0xbf040000 0x84000000 0x10000;
go 0x84000040"
$ setenv bootcmd "run apb_fb_openwrt"
$ saveenv
2. Load the OpenWrt initramfs image on the device using TFTP.
Place the initramfs image as "ap105.bin" in the TFTP server
root directory, connect it to the AP and make the server reachable
at 192.168.1.66/24.
$ run apb_rb_openwrt
3. Once OpenWrt booted, transfer the sysupgrade image to the device
using scp and use sysupgrade to install the firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
In addition to standardizing LED names to match the rest of the systems, this
commit fixes a possibly erroneous pinout for LEDs in Comfast CF-E314N v2.
In particular, rssimediumhigh and rssihigh are moved from pins 13 and 14 to
14 and 16 respectively. In addition to working on a test device, this pinout
better matches the one set out in the prototype support patch for the device
in Github PR #1873.
Signed-off-by: Mark Onstid <turretkeeper@mail.com>
RA75 has 5 physical LEDs under 2 indicators, mixed with light pipes:
Indicator "System":
GPIO0: blue
GPIO2: amber
Indicator "Signal":
GPIO44: blue
GPIO37: amber
GPIO46: red
All except GPIO46 were already added by Jo Deisenhofer. GPIO46 is used for UART1 by
default, so it needs additional pin control change in devicetree to be operational.
Verified on my RA75.
Signed-off-by: Oleksandr Zharov <alex.zeed@gmail.com>
Re-enable the Aruba AP-365 with DSA support. Changes are trvivial, as
the board design is pretty much the already updated AP-303.
Run-tested on the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Import commit "ubi: Fix failure attaching when vid_hdr offset equals to
(sub)page size" which did not yet make it to stable upstream Linux trees.
Fixes: #12232Fixes: #12339
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Updating to U-Boot 2023.04 broke the build for the RAVPower RP-WD009
MT7628 board. This was due to upstream conversion of CONFIG_* to CFG_*
which was not applied to our downstream patch adding support for the
RAVPower RP-WD009 device.
Apply CONFIG_* to CFG_* converion analog to what has been done also
for mt7928_rfb upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that new pinconf features have been backported sync pinctrl-mt7981
and pinctrl-m7986 with bleeding-edge upstream versions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport new features for MediaTek pinctrl/pinconf drivers from upstream.
This will serve as the base to improve pinconf bias/pull-up/pull-down on
MT7981 and MT7986, and also prepare for upcoming support for MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Avoid MCU getting "command reply receive timed out" message when LED
configuration setting trigger function is enabled in heartbeat mode.
Signed-off-by: Ian Chang <ianchang@ieiworld.com>
Update to next U-Boot timed release.
Remove now obsolete patch
100-01-board-mediatek-add-more-network-configurations.patch
Default IP addresses are now dealt with in Kconfig, no longer in board-
specific C header files.
Add patches to restore ANSI support in bootmenu which was broken upstream,
always use high-speed mode on serial UART for improved stability and fix
an issue with pinconf not being applied on MT7623 resulting in eMMC
being inaccessible when booting from micro SD card.
In order to keep the size of the bootloader on MT7623 below 512kB remove
some unneeded commands on both MT7623 boards.
Tested on:
* BananaPi BPi-R2 (MT7623N)
* BananaPi BPi-R3 (MT7986A)
* BananaPi BPi-R64 (MT7622A)
* Linksys E8450 (MT7622B)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is a silent command that allows easy wifi up/down automation for
scripts.
It takes one or multiple devices as arguments (or all if none are passed),
and the exit code indicates if any of those is not up.
E.g.:
wifi isup && echo "all wifi devices are up"
wifi isup radio0 || echo "this wifi is down"
Signed-off-by: Andre Heider <a.heider@gmail.com>
Use the already present but unused $cmd and $dev variables instead of
positional parameters in ubus_wifi_cmd() to improve readability.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Synchronize the ath11k backports with the current ath-next tree.
This replaces the management TLV pending fix with the upstreamed one,
fixes traffic flooding when AP and monitor modes are used at the same time,
fixes QCN9074 always showing -95 dBm for station RSSI in dumps,
fixes potential crash on boot if spectral scan is enabled due to writing to
unitialized memory and adds 11d scan offloading for WCN6750 and WCN6855.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh multiple lzma configuration option patch with new version
proposed upstream. (Reintroduce -Xe option and add more checks and
general better code quality)
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit a33b97dcb1.
A new version of the squashfs4 tool patch reintroduced the -Xe option.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently, during initialization ath11k will receive a regulatory event
from the firmware in which it will receive the default regulatory domain
code and accompanying rules list and report those to the kernel.
Then if you try to change the regulatory domain to a different country code
it will do a weird thing in which it will send that to the FW and after
receiving the appropriate regulatory event it will parse the rules.
However, while its parsing there is a weird thing being done, and that is
that new raw rules from FW get intersected with the rules from the default
domain.
This is creating a big issue as the default domain is almost always set to
"US" or just "00" aka world so ath11k will unfairly limit you to the most
restrictive combination of rules based on the default domain and your
desired domain.
For example, in ETSI countries this is causing channels 12 and 13 on 2.4GHz
to not be usable since "US" limits 2.4GHz to 2472MHz instead of 2482MHz
like ETSI countries do.
So, lets do what TIP and even QCA do in their ath11k downstream tree and
completely get rid of the interesection code in ath11k.
Signed-off-by: Robert Marko <robimarko@gmail.com>
When using "ubiformat" with stdin it requires passing image size using
the -S argument. Provide it just like we do for "ubiupdatevol".
This fixes:
ubiformat: error!: must use '-S' with non-zero value when reading from stdin
This change fixes sysupgrade for bcm53xx and bcm4908 NAND devices
possibly some other targets too.
Cc: Rodrigo Balerdi <lanchon@gmail.com>
Cc: Daniel Golle <daniel@makrotopia.org>
Fixes: 9710712120 ("base-files: accept gzipped nand sysupgrade images")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
It appears that the refactor of the upgrade process for NAND devices resulted in the nand_do_upgrade_success step not being called for
devices using the linksys.sh script. As a result, configuration was
not preserved over sysupgrade steps.
This corrects a typo in the call of nand_do_upgrade_failed for ipq40xx
and ipq806x devices using the linksys.sh script.
Fixes: 8634c1080d ("ipq40xx: Fix Linksys upgrade, restore config step")
Fixes: 2715aff5df ("ipq806x: Fix Linksys upgrade, restore config step")
Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
