Manually rebased patches:
bcm27xx:
patches-5.4/950-0267-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch
bcm53xx:
patches-5.4/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
layerscape:
patches-5.4/802-can-0025-can-flexcan-add-LPSR-mode-support-for-i.MX7D.patch
patches-5.4/808-i2c-0002-MLK-10893-i2c-imx-add-irqf_no_suspend.patch
patches-5.4/820-usb-0016-MLK-16735-usb-host-add-XHCI_CDNS_HOST-flag.patch
Removed since could be reverse-applied by quilt:
mediatek:
patches-5.4/0700-arm-dts-mt7623-add-missing-pause-for-switchport.patch
All modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711, x86_64
Run-tested: ipq806x/R7800, x86_64
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [x86_64]
Rebase of 802-can-0025-can-flexcan-add-LPSR-mode-support-for-i.MX7D.patch
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
We use 5.4 on all targets by default, and 4.19 has never been released
in a stable version. There is no reason to keep it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The generic bootscript is tailored around a downstream firmware and
doesn't work on a firmware built from mainline components.
Add a bootscript which:
* sets $console since mainline u-boot doesn't do that
* uses distro boot variables, so OpenWRT can be booted off any supported
device when using a mainline firmware
* sets missing distro boot variables for the downstream firmware
Booting with a downstream firmware is unchanged.
Booting with a mainline firmware now works.
Signed-off-by: Andre Heider <a.heider@gmail.com>
correct oversight on setting regulatory country and mac address of wireless configuration
change method of retrieving mac address
The MAC address for eth0 is rad out of the devinfo partition in some
other initial configuration script already.
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
correct device CC oversight
Set the initial wifi configuration like for the other similar Linksys
devices.
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
This commit contains patches for PCI aardvark driver and relevant DTS
changes for Turris MOX and EspressoBin backported from mainline kernel.
It fixes support for old ATF, various wifi cards, mainly Compex WLE900VX.
Signed-off-by: Pali Rohár <pali@kernel.org>
Similar to how it was already done for other filesystems' *_FS_XATTR
kernel config symbols, also move CONFIG_F2FS_FS_XATTR=y and
CONFIG_F2FS_STAT_FS=y to target/linux/generic.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Extended attributes are required for overlayfs and have hence been long
ago enabled for jffs2, but should be enabled unconditionally for all
other filesystems which may potentially serve as overlayfs' upper
directory. Previously it was inconsistently added in multiple targets.
Add symbols to generic kernel config and remove all *_XATTR symbols
from target configs.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[keep things as they are for squashfs, improve commit message]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Seemingly unneeded based on new upstream code so manually deleted:
layerscape:
820-usb-0007-usb-dwc3-gadget-increase-timeout-value-for-send-ep-c.patch
Manually merged:
generic-hack:
251-sound_kconfig.patch
All other modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800, lantiq/Easybox 904 xDSL
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[add lantiq test report, minor commit message clarification]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
SPDX moved from GPL-2.0 to GPL-2.0-only and from GPL-2.0+ to
GPL-2.0-or-later. Reflect that in the SPDX license headers.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
fdt_addr and kernel_addr variables are getting obsolete in the mainline
u-boot in favor of fdt_addr_r and kernel_addr_r.
By checking if the new variables exist, we can make sure that devices with newer
version of u-boot will work while not breaking support for the existing ones.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The uci-default mechanism to update the compat-version was only
meant for early DSA-adopters, which should have updated by now.
Remove this workaround again in order to prevent the intended
experiences for all the other people.
This reverts:
a9703db720 ("mvebu: fix sysupgrade experience for early DSA-adopters")
86c89bf5e8 ("kirkwood: fix sysupgrade experience for early DSA-adopters")
Partially reverted:
1eac573b53 ("ramips: mt7621: implement compatibility version for DSA migration")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit e81e625ca3.
This was meant just for early DSA-adopters. Those should have
updated by now, remove it so future updaters get the intended
experience.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Manually merged:
hack-5.4
230-openwrt_lzma_options.patch
bcm27xx
950-0283-hid-usb-Add-device-quirks-for-Freeway-Airmouse-T3-an.patch
x86
011-tune_lzma_options.patch
Remove upstreamed patches in collaboration with Ansuel Smith:
ipq806x
093-1-v5.8-ipq806x-PCI-qcom-Add-missing-ipq806x-clocks-in-PCIe-driver.patch
093-2-v5.8-ipq806x-PCI-qcom-Change-duplicate-PCI-reset-to-phy-reset.patch
093-3-v5.8-ipq806x-PCI-qcom-Add-missing-reset-for-ipq806x.patch
All other modifications made by update_kernel.sh
Build-tested: bcm27xx/bcm2708, ipq806x, x86/64
Run-tested: ipq806x (R7800), x86/64
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[update commit message/tested]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Compile the Linkstation poweroff module for the Buffalo LS421DE.
Without this driver the device remains forever halted if a power off
command is executed.
The driver will also allow to use the WoL feature, which wasn't availabe
in the stock firmware.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Backport the Linkstation poweroff driver from the kernel upstream (commit
a7f79f99541ef)
This driver is required by the Buffalo LinkStation LS421DE for a correct
power off operation. It also allows to use the WoL feature.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
In order to support SAE/WPA3-Personal in default images. Replace almost
all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for
consistency. Keep out ar71xx from the list as it won't be in the next
release and would only make backports harder.
Build-tested (build-bot settings):
ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway,
sunxi: a53
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This PR is a blend of several kernel bumps authored by ldir taken from his
staging tree w/ some further adjustments made by me and update_kernel.sh
Summary:
Deleted upstreamed patches:
generic:
742-v5.5-net-sfp-add-support-for-module-quirks.patch
743-v5.5-net-sfp-add-some-quirks-for-GPON-modules.patch
bcm63xx:
022-v5.8-mtd-rawnand-brcmnand-correctly-verify-erased-pages.patch
024-v5.8-mtd-rawnand-brcmnand-fix-CS0-layout.patch
mediatek:
0402-net-ethernet-mtk_eth_soc-Always-call-mtk_gmac0_rgmii.patch
Deleted patches applied differently upstream:
generic:
641-sch_cake-fix-IP-protocol-handling-in-the-presence-of.patch
Manually merged patches:
generic:
395-v5.8-net-sch_cake-Take-advantage-of-skb-hash-where-appropriate.patch
bcm27xx:
950-0132-lan78xx-Debounce-link-events-to-minimize-poll-storm.patch
layerscape:
701-net-0231-enetc-Use-DT-protocol-information-to-set-up-the-port.patch
Build system: x86_64
Build-tested: ath79/generic, bcm27xx/bcm2708, bcm27xx/bcm2711,
imx6, mvebu/cortexa9, sunxi/a53
Run-tested: Netgear R7800 (ipq806x)
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-By: Lucian Cristian <Lucian.cristian@gmail.com> [mvebu]
Tested-By: Curtis Deptuck <curtdept@me.com> [x86/64]
[do not remove 395-v5.8-net-sch_cake-Take-advantage-... patch,
adjust and refresh patches, adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-By: John Audia <graysky@archlinux.us> [ipq806x]
It is deactivated everywhere, just set this in the generic config.
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add a specific comment for early DSA-adopters that they can keep
their config when prompted due to compat-version increase.
This is a temporary solution, the patch should be simply reverted
before any release.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Conceptually, the compat-version during sysupgrade is meant to
describe the config. Therefore, if somebody starts with a device on
19.07 and swconfig, and that person does a forceful upgrade into a
DSA-based firmware without wiping his/her config, then the local
compat-version should stay at 1.0 according to the config present
(and not get updated).
However, this poses a problem for those people that early-adopted
DSA in master, as they already have adjusted their config for DSA,
but it still is "1.0" as far as sysupgrade is concerned. This can
be healed by a simple
uci set system.@system[0].compat_version="1.1"
uci commit system
But this needs to be applied _after_ the upgrade (as the "old" fwtool
on the old installation does not know about compat_version) and it
requires access via SSH (i.e. no pure GUI solution is available for
this group of people, apart from wiping their config _again_ for
no technical reason). Despite, the situation will not become
obvious to those just upgrading via GUI, they will just have the
experience of a "broken upgrade".
This is a conflict which cannot be resolved by achieving both goals,
we have to decide to either keep the strict concept or improve the
situation for early adopters.
In this patch, we address the issue by providing a uci-defaults
script that will raise the compat_version for _all_ people upgrading
into a 1.1 image, no matter whether they have reset config or not.
The idea is to implement this as a _temporary_ solution, so early
adopters can upgrade into the new mechanism without issues, and
after a few weeks/months we could remove the uci-defaults script
again.
If we e.g. remove the script just before 20.xx.0-rc1, early adopters
should have moved on by then, and existing stable users would still
get the intended experience.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When changing the Pro variant to DSA, the ethernet interface rename
script was dropped by all devices to keep them in sync:
be309bfd74 ("mvebu: drop 06_set_iface_mac preinit script")
Therefore, network config will be broken after upgrade for the
Base variant as well. Increase the compat version and provide a
message to signal that to the users.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This implements the newly introduced compat-version to prevent
upgrade between swconfig and DSA for mvebu.
Just define a compat version with minor increment and an appropriate
message for both image (in Makefile) and device (in base-files).
Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES
that have been removed in previous patches to prevent broken config.
Attention:
All users that already updated to the DSA versions in master will
receive the same incompatibility warning since their devices are still
"1.0" as far as fwtool can tell.
Those, and only those, can bypass the upgrade check by using force (-F)
without having to reset config again. In addition, the new version
string needs to be put into uci config manually, so the new fwtool
knows that it actually deals with a "1.1":
uci set "system.@system[-1].compat_version=1.1"
uci commit system
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Use "DEFAULT := n" to only disable devices for buildbots, but
keep them available for manual build.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The kernel appears to have grown too large, breaking the build for the
entire target.
Disable the affected images for now until the situation is dealt with.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
update_kernel.sh refreshed all patches, no human interaction was needed
Build system: x86_64
Run-tested: Netgear R7800 (ipq806x)
Signed-off-by: John Audia <graysky@archlinux.us>
The Helios 4 is a NAS from Kobol
that is powered by an Armada 38x
MicroSOM from Solidrun, similarly
to Clearfog.
This device has:
-Armada 38x CPU
(dual core ARMv7 1.6 Ghz)
-2 GB of ECC RAM
-Gigabit ethernet (Marvell)
-2x USB 3.0 ports
-4x Sata 3.0 ports
-i2c header (J9 |>GND|SDA|SCL|VCC)
-2x 3-pin fan headers with PWM
-micro-usb port is a TTL/UART to
USB converter connected to TTL
-MicroSD card slot
-System, 4xSata and 1xUSB LEDs
NOT WORKING: fan control
Fan Control requires a kernel patch
that is available in the Armbian
project (the "default firmware"
of this device) and named
mvebu-gpio-remove-hardcoded
-timer-assignment
This patch isn't acceptable
by OpenWrt, it should be upstreamed.
I also have that patch in my own
local OpenWrt builds,
in case you want a more
clean and less confusing patch
for upstreaming.
To install, write the disk image
on a micro SD card with dd or
win32 disk imager, insert the
card in the slot.
Check that the dip switch battery
for boot selection is as follows
Switch 1 and 2 down/off, switches
3, 4, 5 up/on.
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
Add support for Marvell MACCHIATObin Single Shot, cortex-a72 based
Marvell ARMADA 8040 Community board. Single Shot was broken as the
device tree is different on the Double Shot Board.
Specifications:
- Quad core Cortex-A72 (up to 2GHz)
- DDR4 DIMM slot with optional ECC and single/dual chip select support
- Dual 10GbE (1/2.5/10GbE) SFP+
2.5GbE (1/2.5GbE) via SFP
1GbE via copper
- SPI Flash
- 3 X SATA 3.0 connectors
- MicroSD connector
- eMMC
- PCI x4 3.0 slot
- USB 2.0 Headers (Internal)
- USB 3.0 connector
- Console port (UART) over microUSB connector
- 20-pin Connector for CPU JTAG debugger
- 2 X UART Headers
- 12V input via DC Jack
- ATX type power connector
- Form Factor: Mini-ITX (170 mm x 170 mm)
More details at http://macchiatobin.net
Installation:
Write the Image to your Micro SD Card and insert it in the
MACCHIATObin Single Shot SD Card Slot.
In the U-Boot Environment:
1. reset U-Boot environment:
env default -a
saveenv
2. prepare U-Boot with boot script:
setenv bootcmd "load mmc 1:1 0x4d00000 boot.scr; source 0x4d00000"
saveenv
or manually (hanging lines indicate wrapped one-line command):
setenv fdt_name armada-8040-mcbin-singleshot.dtb
setenv image_name Image
setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr
$image_name;ext4load mmc 1:1 $fdt_addr $fdt_name;setenv
bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti
$kernel_addr - $fdt_addr'
saveenv
On newer Bootloaders (18.12) the Variables have been changed, use:
setenv fdt_name armada-8040-mcbin-singleshot.dtb
setenv image_name Image
setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr_r
$image_name;ext4load mmc 1:1 $fdt_addr_r $fdt_name;setenv
bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti
$kernel_addr_r - $fdt_addr_r'
Reported-by: Alexandra Alth <alexandra@alth.de>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: Alexandra Alth <alexandra@alth.de>
[add specs and installation as provided by Alexandra Alth]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Between kernels 4.20 and 5.0, a new variant of this board has been
introduced ("Single Shot"), and the existing one has been renamed
with the appendix "Double Shot". [1]
This also adjusted the first compatible in the list:
marvell,armada8040-mcbin -> marvell,armada8040-mcbin-doubleshot
This patch updates the OpenWrt implementation of this device by
adjusting the relevant references to that compatible (i.e., our
board name).
To still provide support for 4.19 with our setup, this adds a
small patch to change the compatible there as well.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=b1f0bbe2700051886b954192b6c1751233fe0f52
Cc: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
We are setting CONFIG_I2C_PXA is not set
If you do set pxa to y then you have issues if you do not have
CONFIG_I2C_PXA_SLAVE is not set
Fixes: dd13add3ce ("kernel: i2c-pxa: remove slave")
Signed-off-by: Scott Roberts <ttocsr@gmail.com>
The Buffalo Linkstation LS421DE has a chassis fan for cooling two internal
hard drives. Currently there is no control over this fan, running always
at fixed medium speed.
With the recent jump to the kernel 5.4, now we can monitor the hard drive
temperature and control the fan with thermal zones.
Install the kmod-hwmon-drivetemp module and wire up a thermal zone on the
dts file to allow automatic fan control by the kernel.
Tested succesfully using a single Crucial BX500 SSD drive.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Fixes:
- CVE-2020-10757
The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.
Run tested: ath79
Build tested: ath79
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Device/Default definition in mvebu defines an IMAGE/factory.img
which is not included in IMAGES, and only used twice in the
individual definitions. Move it out of the default definition
to keep it closer to the reassignment of IMAGES and make it more
consistent with respect to other values of IMAGE/factory.img
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In 02_network, the board name solidrun,clearfog-a1 is used in a
case, but it does not seem to be used/exist anywhere else in OpenWrt.
The valid strings are:
- solidrun,clearfog-pro-a1
- solidrun,clearfog-base-a1
Fixes: 12795ec9f1 ("mvebu: split interface configuration for
clearfog pro and base")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- Delete useless HDD presence inputs: they aren't buttons, and probably
they are outputs in the stock firmware.
- Change the Function Button keycode: the current one isn't mapped by
the kernel module.
- Use the recommended property names for the ethernet stuff.
- Add missing i2c pinmux.
- Minor cosmetic changes.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The DTS files in files-4.19 and files-5.4 are exactly identical
except for one file (armada-3720-uDPU.dts), which is only present
for 4.19, as it has been upstreamed before 5.4.
Since there is no point in maintaining all these identical files
twice, this patch moves them to the "files" directory, only keeping
the named exception to files-4.19.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The mwlwifi driver sets the default country code for EU (fi-
rmware region code 0x30) certified devices to FR (France),
not DE (Germany). Whilst this is a trivial fix, novice users
may not know how mwlwifi negatively reacts to a non-matching
country code and may leave the setting alone. Especially si-
nce it is under the advanced settings section in LuCI.
Relevant mwlwifi driver code:
0a550312dd
The mwlwifi driver readme states "Please don't change country
code and let mwlwifi set it for you." However, OpenWrt's current
behaviour does not adhere to this with its default, 'just flashed
from factory' setting for EU devices.
Signed-off-by: Jose Olivera <oliverajeo@gmail.com>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently I'm unable to boot initramfs image with `console=ttyS0,115200`
kernel commandline as the kernel commandline mangling resets kernel
commandline if there is no `root=` option provided, efectively clearing
whatever I pass to the kernel, making the `root=` option mandatory.
So if the kernel commandline mangling is not appropriate just leave the
kernel commandline as it is.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.
While at it, fix the executable flag on a few of these files.
This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
