These get dynamically set based on compiler version. Not relevant for
targets.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16770
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This symbol is no longer present.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16770
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This GPIO is pulled down by the onboard MCU when the power button
is pressed for 5 seconds, indicating a user-initiated shutdown.
Refresh patches at the same time.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Remove folder with DTS files for Linux 6.1 which has already been
dropped.
Fixes: f142ce87d9 ("kirkwood: remove 6.1 support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The company Zyxel rebranded some years ago.
Currently the casing is according to the old branding even
for newer devices which already use the new branding.
This commit aligns the casing of Zyxel everywhere.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15652
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Kirkwood was switched to 6.6. We can remove 6.1 support now.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15998
Signed-off-by: Robert Marko <robimarko@gmail.com>
generic.mk was commited by mistake. It isn't used. Let's remove it.
Fixes: ccbdb212f3 ("kirkwood: Add missing package dependency")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15998
Signed-off-by: Robert Marko <robimarko@gmail.com>
Let's switch to kernel 6.6 for wide tests.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15998
Signed-off-by: Robert Marko <robimarko@gmail.com>
gpio is deprecated. Found with dtc's -Wdeprecated_gpio_property
Used git grep -E $'\tgpio = <' to make the changes.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15681
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The recently added D-Link DNS-320L and the Zyxel NSA310S
is missing an RTC module so let's give them the default
Marvell RTC at least.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Dual-slot NAS based on Marvell Kirkwood.
Specifications:
- Marvell 88F6702 @1GHz
- 256Mb RAM
- 128Mb NAND
- 1x GbE LAN (Marvell 88E1318R)
- 1x USB 2.0
- 2x SATA
- Weltrend WT69P3 ("supervisor" MCU chip)
- Serial on J2 (115200,8n1)
- Newer bootROM so kwboot-ing via serial is possible
Notes:
- The Weltrend MCU is controlled by the package added in utils/dns320l-mcu.
- The original MAC address is stored in the "mini firmware" image's first
17 bytes.
- Compared to the original MTD layout, the uImage+rootfs are now stored in
a common ubi partition.
Installation:
1. Serial console
- Connect your levelshifter to the serial console
on J2 (refer to the wiki page for pinout)
2. Update u-boot
- Download the u-boot.kwb image for the device
- Powercycle the NAS
- Run "kwboot -b u-boot-dns320l/u-boot.kwb /dev/ttyUSB0 -p"
- Connect to the serial console with minicom
- tftp 0x0800000 u-boot-dns320l/u-boot.kwb
(Please note that "PHY reset timed out" seems to be customary
on kirkwood devices, the egiga0 interface works regardless.)
- nand erase 0x0 100000
- nand write 0x0800000 0x0 0x100000
- reset
3. Install OpenWrt
- Boot up the initramfs image
- tftpboot 0x800000 openwrt-kirkwood-generic-dlink_dns320l-initramfs-uImage; bootm 0x800000
- Download the sysupgrade image and perform sysupgrade
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
The backports introduced in commit d40756563c ("kernel: backport
phylink changes from mainline Linux") broke the mv88e6xxx DSA driver.
A backport to fix this was added to the kirkwood target, but as it is
used in multiple targets, and there's a kmod package for it, the fix
should be in generic backports.
This fixes the switch on the WatchGuard Firebox M300 when running the
6.1 testing kernel.
There is no need to backport the fix for the 6.6 kernel, as it was
included in 6.6.5.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This is an automatically generated commit.
During a `git bisect` session, `git bisect --skip` is recommended.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The 6.1 kernel has caused another increase in kernel size, and now
it's more than 3MB:
WARNING: Image file iom_ix4-200d-uImage is too big: 3170394 > 3145728
WARNING: Image file iom_ix2-200-uImage is too big: 3171494 > 3145728
WARNING: Image file linksys_e4200-v2-uImage is too big: 3171879 > 3145728
WARNING: Image file linksys_ea4500-uImage is too big: 3171871 > 3145728
WARNING: Image file linksys_ea3500-uImage is too big: 3171651 > 3145728
This causes problems for 5 devices:
- Iomega StorCenter ix2/ix4
- Linksys EA3500/EA4200/EA4500
They have enough resources for proper operation with 6.1, but all of
them had a 3MB kernel size limit. Let's keep them alive and
resize kernel partitions to 4MB.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
6.1 testing version was introduced some time ago. Kernel size issues
are resolved now. Time to bump kernel version.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
When build images with the 6.1 kernel for all devices and all kmods,
there is one dependancy error:
pkg_hash_check_unresolved: cannot find dependency kmod-thermal
for kmod-hwmon-gpiofan
This commit fix that issue.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Copied from original Andrew's Lunn commit message:
The DSA framework has got more picky about always having a phy-mode
for the CPU port. The Kirkwood Ethernet is an RGMII port. Set the
switch to impose the RGMII delays.
Additionally, the cpu label has never actually been used in the
binding, so remove it.
This commit backport change from upstream and fix downstream EA3500 dts.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Dual-slot NAS based on Marvell Kirkwood.
Specifications:
- Marvell 88F6281 @1GHz
- 128Mb RAM
- 256Mb NAND
- 1x GbE LAN (Marvell 88E1116)
- 1x USB 2.0
- 2x SATA
- PCF8563 RTC
- LM75 sensor
- TC654 PWM fan controller
- Serial on J2 (115200,8n1)
- Newer bootROM so kwboot-ing via serial is possible
Installation:
1. Serial console
- Connect your levelshifter to the serial console
on J2 (refer to the wiki page for pinout)
2. Update u-boot
- Download the u-boot.kwb image for the device
- Powercycle the NAS
- Run "kwboot -b ./u-boot.kwb /dev/ttyUSB0 -p"
- Connect to the serial console with minicom
- tftp 0x0800000 netgear_stora-u-boot.kwb
- nand erase 0x0 100000
- nand write 0x0800000 0x0 0x100000
- reset
3. Install OpenWrt
- Boot up the initramfs image
- tftpboot 0x800000 openwrt-kirkwood-netgear_stora-initramfs-uImage; bootm 0x800000
- Download the sysupgrade image and perform sysupgrade
The fan is controlled in 3 stages by a script running every minute
from cron, measuring the CPU temperature.
Snippets taken from bodhi <mibodhi@gmail.com>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The Kirkwood SoCs all have an onchip RTC that can hold the time
over e.g. a reboot which will help if no NTP servers are available.
Create a kernel module package for the Marvell RTC, and add it to
all Kirkwood devices that do not have their own discrete
battery-backed RTC. Adding it to platforms with a proper RTC
is just surplus.
All Kirkwoods have at least one RTC so add RTC to the features
list for Kirkwood as well.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
From the original Patch:
|In 749237967a downstream dts was replaced with upstream accepted
|patch. But in upstream version last partition was called "rootfs"
|instead "ubi". OpenWrt require "ubi" label for ubi rootfs.
|This patch restore proper label.
|
|Fixes: 749237967a ("kirkwood: Replace dtses with upstream accepted")
|
|Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(patch updated to include 6.1, dropped label properties)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
In 749237967a downstream dts was replaced with upstream accepted
patch. But in upstream version last partition was called "rootfs"
instead "ubi". OpenWrt require "ubi" label for ubi rootfs.
This patch restore proper label.
Fixes: 749237967a ("kirkwood: Replace dtses with upstream accepted")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Iomega Storcenter ix4-200d is a four-bay SATA NAS powered by a Marvell
Kirkwood SoC clocked at 1.2GHz. It has 512MB of RAM and 32MB of
flash memory, 3x USB 2.0 and 2x 1Gbit/s NIC
Specification:
- SoC: Marvell Kirkwood 88F6281
- CPU/Speed: 1200Mhz
- Flash size: 32 MiB
- RAM: 512MB
- LAN: 2x 1Gbit/s
- 3x USB 2.0
Notes:
- The blue drive LED is triggered by HDD activity, it can not be controlled
via GPIO.
- The LCD screen requires proprietary code and does not function at this time.
- Due to a kernel-related issue with the Marvell 88SE6121 SATA controller,
currently only trays numbered #3 and #4 work, #1 and #2 do not. [1]
Serial pinout:
CN4
--------------
| 10 8 6 4 2 |
| 9 7 5 3 1 |
-------------- PIN 1 Mark (fat line)
1 = RXD
4 = TXD
6 = GND
9 = 3.3V (not necessary to connect)
Installation instructions:
1. download initramfs-uImage and copy into tftp server
2. connect the tftp server to network port #1
3. access uboot environment with serial cable and run
setenv mainlineLinux yes
setenv arcNumber 1682
setenv console 'console=ttyS0,115200n8'
setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
setenv bootargs_root 'root='
setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
saveenv
setenv serverip 192.168.1.1
setenv ipaddr 192.168.1.2
tftpboot 0x00800000 [initramfs-uImage filename]
bootm 0x00800000
4. connect to LAN on network port #2, log into openwrt and sysupgrade to install into flash
[1] https://bugzilla.kernel.org/show_bug.cgi?id=216094
Signed-off-by: Sander van Deijck <sander@vandeijck.com>
(aligned FROM from signed-off. LED+key rename, whitespace removal)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
DTSes from of three boards was sent and accpeted upstream. Let's use
backport patches with small OpenWrt tweak like other upstream stuff.
List of boards:
- Zyxel NSA310S
- Endian 4i Edge 200
- Ctera C-200 V1
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
All targets are bumped to 5.15. Remove the old 5.10 patches, configs
and files using:
find target/linux -iname '*-5.10' -exec rm -r {} \;
Further, remove the 5.10 include.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Fix following error when building 32bit arm targets with kmod-crypto-sha512
ERROR: module '/home/user/openwrt/build_dir/target-arm_xscale_musl_eabi/linux-kirkwood_generic/linux-5.15.109/arch/arm/crypto/sha512-arm.ko' is missing.
Signed-off-by: Lu jicong <jiconglu58@gmail.com>
It appears that the refactor of the upgrade process for NAND devices
resulted in the nand_do_upgrade_success step not being called for
devices using the linksys.sh script. As a result, configuration was
not preserved over sysupgrade steps.
This restores the preservation of configs for kirkwood devices using the
linksys.sh script.
Fixes: e25e6d8e54 ("base-files: fix and clean up nand sysupgrade code")
Fixes: #12298
Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
Starting from Linux Kernel version 6.3 UBI devices will no longer be
considered virtual, but rather have an MTD device parent. Hence they
will no longer be listed under /sys/devices/virtual/ubi which is
used in multiple places in OpenWrt. Prepare for future kernels by
using /sys/class/ubi instead of /sys/devuces/virtual/ubi.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
