Commit Graph

651 Commits

Author SHA1 Message Date
Adrian Schmutzler
c642a97aa6 ath79: add support for TP-Link TL-WDR4300 v1 (IL)
The TL-WDR4300 v1 sold in Israel has a different TPLINK_HWID.

Thanks to Josh4300 for testing on device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 14:42:05 +01:00
Adrian Schmutzler
8e91b18ab7 ath79: redistribute UBNT variables in Ubiquiti image Makefile
The variables UBNT_BOARD and UBNT_VERSION are defined in the parent
Device/ubnt definition and then overwritten for most of the derived
platform definitions (e.g. Device/ubnt-wa).

Since this mixed use of inheritance and overwriting can be misleading,
this moves the variables to the platform-based definitions.

While at it, reorder the definitions to have order consistent, too.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:18:01 +01:00
DENG Qingfang
46c74944df ath79: fix typos in DTS
Replace "usb_ochi" with "usb_ohci", and "usb_echi" with "usb_ehci".

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-12-11 22:50:12 +01:00
Koen Vandeputte
88ca372b5a kernel: bump 4.19 to 4.19.88
Refreshed all patches.

Remove upstreamed:
- 0004-boot-sq201-from-sda1.patch
- 500-v4.20-ubifs-Fix-default-compression-selection-in-ubifs.patch
- 0003-usb-dwc2-use-a-longer-core-rest-timeout-in-dwc2_core.patch

Altered patches:
- 0011-ARM-dts-Fix-up-SQ201-flash-access.patch
- 400-mtd-add-rootfs-split-support.patch
- 0101-pci-mediatek-backport-fix-pcie.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-12-10 09:50:42 +01:00
Koen Vandeputte
d395583d69 kernel: bump 4.14 to 4.14.158
Refreshed all patches.

Altered patches:
- 400-mtd-add-rootfs-split-support.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-12-10 09:50:42 +01:00
Adrian Schmutzler
231dc26867 treewide: remove dts-v1 identifier from DTSI files
The "/dts-v1/;" identifier is supposed to be put once at the beginning
of a device tree file. Thus, it makes no sense to provide it a second
time in to-be-included DTSI files.

This removes the identifier from all DTSI files in /target/linux.

Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is
missing for most of the following targets, though:
mvebu, ipq806x, mpc85xx, ipq40xx

This does not touch ipq806x for now, as the bump to 4.19 is close.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-08 16:44:06 +01:00
Christian Lamparter
a428606646 ath79: fix WNDR3700/WNDR3800 wifi reg size
"[...] the size component shall be zero."
(See "PCI Bus Binding to: IEEE Std 1275-1994 Rev 2.1"
section "4.1.1 Open Firmware-defined Properties for Child Nodes")

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-12-07 12:01:23 +01:00
Stijn Tintel
157e17e985 ath79: add support for Ubiquiti LiteBeam AC Gen2
Hardware:
* SoC: Atheros AR9342-BL1A
* RAM: 64MB DDR2 (Winbond W9751G6KB-25)
* Flash: 16MB SPI NOR (Macronix MX25L12835FZ2I-10G)
* Ethernet: 1x 10/100/1000 Mbps (Atheros AR8035-A) with 24V PoE support
* Wifi 2.4GHz: Atheros AR9340 v2
* WiFi 5GHz: Ubiquiti U-AME-G1-BR4A (rebranded QCA988X v2)
* LEDs: 1x Power, 1x Ethernet
* Buttons: 1x Reset
* UART: 1x TTL 115200n8, 3.3V RX TX GND, 3.3V pin closest to RJ45 port

The LEDs do not seem to be connected to any GPIO, so there is currently
no way to control them.

Installation via U-Boot, TFTP and serial console:
* Configure your TFTP server with IP 192.168.1.254
* Connect serial console and power up the device
* Hit any key to stop autoboot
* tftpboot 0x81000000 openwrt-ath79-generic-ubnt_litebeam-ac-gen2-initramfs-kernel.bin
* bootm 0x81000000
* copy openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin
  to /tmp
* sysupgrade /tmp/openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-04 23:17:41 +02:00
Stijn Tintel
db26f53bb3 ath79: drop IMAGE/factory.bin from ubnt-wa devices
The sysupgrade image contains OpenWrt specific metadata. Having this
metadata in the factory images makes no sense. Drop IMAGE/factory.bin
from Device/ubnt-wa and use the default from Device/ubnt instead.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-04 23:17:41 +02:00
Adrian Schmutzler
f6385f30bd ath79: fix source of label MAC address for Ubiquiti XM devices
In d421a8b944 ("ath79: read label MAC address from flash instead
of using phy0/phy1") the source of the label MAC address was changed
for devices just reading it from phy0. To get rid of the dependency
from phy startup, addresses were read directly from the flash
locations that are used to initialize the phy MAC addresses.

Unfortunately, it turned out that Ubiquiti XM devices seem to have
different flash locations than expected, and also seem to have
specific locations for different devices (all in art/EEPROM):

0xe012 AR9280 Nanostation M2 - 0x120c
0xe035 AR9280 Nanostation M3 - 0x120c
0xe1b2 AR9280 Rocket M2 - 0x120c
0xe1c3 AR9280 Rocket M3 - 0x120c
0xe1b5 AR9280 Rocket M5 - 0x120c
0xe2d5 AR9280 Bullet M2 Titanium - 0x120c
0xe2b5 AR9280 Nanobridge M5 - 0x120c
0xe202 AR9280 Bullet M2 - 0x120c
0xe232 AR9287 Nanobridge M2 - 0x110c
0xe4a2 AR9285 AirRouter - 0xa0bf
Picostation M2 - 0x120c and 0xa0bf
Nanostation Loco M2 - not in 0x120c, other locations not checked

An additional problem of the Ubiquiti device support in OpenWrt is
that we provide images that match several subvariants of the devices,
which might have different MAC address locations.

Given that reading the address from phy0 in 02_network _is_ working
for the ath79 target in general, it does not seem reasonable to
rebuild a complex MAC address retrieval mechanism which is already
present in the ath9k driver.

So, this patch reverts the label MAC address source for Ubiquiti XM
devices (and the Unifi AP) to /sys/class/ieee80211/phy0/macaddress.

This doesn't affect XW and Unifi AC devices, where the label MAC
address source is defined via device tree.

For alfa-network,ap121f the location 0x1002 is kept, as this has
been verified during device support preparation in PR #2199.

Fixes: d421a8b944 ("ath79: read label MAC address from flash
instead of using phy0/phy1")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-03 13:30:51 +01:00
Koen Vandeputte
f19e471f32 kernel: bump 4.19 to 4.19.86
Refreshed all patches.

Altered patches:
- 950-0064-mfd-Add-Raspberry-Pi-Sense-HAT-core-driver.patch
- 0005-mtd-physmap_of-Move-custom-initialization.patch

Remove upstreamed:
- 0001-pinctrl-gemini-Mask-and-set-properly.patch
- 0002-pinctrl-gemini-Fix-up-TVC-clock-group.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-29 09:59:49 +01:00
Anderson Vulczak
9b90dc05f5 ath79: add support for TP-Link Archer C6 v2 (US) and A6 (US/TW)
This patch is based on #1689 and adds support for TP-Link Archer
C6 v2 (US) and A6 (US/TW).

The hardware is the same as EU and RU variant, except for GPIOs
(LEDS/Buttons), flash(chip/partitions) and UART being available
on the board.

- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q127CS1G (16MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
  - 2.4GHz (bgn) QCA9563 integrated (3x3)
  - 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: 115200, 8n1 (header available on board)

Known issues:
 - Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range.

Flash instructions:

Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin
via the router Web interface.

Flash instruction using tftp recovery:

1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
   tftp root directory renamed to ArcherA6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the
   reset button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing

Flash partitioning: I've followed #1689 for defining the partition layout
for this patch. The partition named as "tplink" @ 0xfd0000 is marked
as read only as it is where some config for stock firmware are stored.
On stock firmware those stock partitions starts at 0xfd9400 however
I had not been able to make it functional starting on the same address as
on stock fw, so it has been partitioned following #1689 and not the stock
partition layout for this specific partition. Due to that firmware/rootfs
partition lenght is 0xf80000 and not 0xf89400 as stock.

According to the GPL code, the EU/RU/JP variant does have different GPIO pins
assignment to LEDs and buttons, also the flash memory layout is different.

GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz

Signed-off-by: Anderson Vulczak <andi@andi.com.br>
[wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases
to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-27 22:54:36 +01:00
Adrian Schmutzler
c08ddfce3f ath79: rename EEPROM to art
This renames all remaining occurrences of "EEPROM" to "art" to
further harmonize the partition labelling in ath79. This will
help to reduce the amount of user-space code and might be
beneficial when code is copy/pasted in the future.

Affected are only devices from Ubiquiti, where the XM board is
already using "art" in ath79.

Acked-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-27 22:54:36 +01:00
Piotr Dymacz
e5d4c09667 ath79: add support for YunCore XD4200 and A782
YunCore XD4200 ('XD4200_W6.0' marking on PCB) is Qualcomm/Atheros based
(QCA9563, QCA9886, QCA8334) dual-band, Wave-2 AC1200 ceiling AP with PoE
(802.3at) support. A782 model ('T750_V5.1' marking on PCB) is a smaller
version of the XD4200, with similar specification but lower TX power.

Specification:

- QCA9563 (775 MHz)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet (QCA8334), with 802.3at PoE support (WAN)
- Wi-Fi 2.4 GHz:
  - XD4200: 2T2R (QCA9563), with ext. PA (SKY65174-21) and LNA
  - A782: 2T2R (QCA9563), with ext. FEM (SKY85329-11)
- Wi-Fi 5 GHz:
  - XD4200: 2T2R (QCA9886), with ext. FEM (SKY85728-11)
  - A782: 2T2R (QCA9886), with ext. FEM (SKY85735-11)
- LEDs:
  - XD4200: 5x (2x driven by SOC, 1x driven by AC radio, 2x Ethernet)
  - A782: 3x (1x RGB, driven by SOC and radio, 2x Ethernet)
- 1x button (reset)
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x DC jack (12 V)

Flash instructions:

If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):

  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
  sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin

In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:

1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
   'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
   seconds, recovery mode should start downloading image from server
   (unfortunately, there is no visible indication that recovery got
   enabled - in case of problems check TFTP server logs)

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-25 17:32:46 +01:00
Vincent Wiemann
8016f64864 ath79: add support for YunCore TFTP image generation
YunCore QCA9k based devices released in 2019 require a custom TFTP image
for U-Boot built-in recovery mode (triggered with reset button). Image
has to be prepended with 'YUNCORE' keyword followed by U-Boot CLI
commands which will be executed later. Images without the custom header
will be ignored by U-Boot.

To be able to support both the vendor firmware (QSDK) and OpenWrt flash
layouts, used here commands change the 'bootcmd' before flashing image.

This commit adds generic helper script for YunCore devices with 16 MB of
flash and enables TFTP image generation for A770 model.

Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>
[pepe2k@gmail.com: commit description reworded, recipe renamed]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-25 17:32:46 +01:00
Piotr Dymacz
c543dfe431 ath79: generic: base-files: fix indentation in 02_network
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-25 17:32:46 +01:00
Stijn Segers
bfabd8d613 ath79: remove ath10k drivers from Archer C7 v1 profile
Ath10k packages were removed from ar71xx in master in commit
34113999ef ("ar71xx: Remove ath10k packages from archer-c7-v1 (fixes
FS#1743)") but ath79 in master and the 19.07 branch still suffer from
the issue.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-11-24 14:19:43 +01:00
Adrian Schmutzler
226bc91109 ath79: improve TP-Link CPE DTSI names for ar9344 SOC
The initial DTSI names for the TP-Link CPE devices have become
quite confusing, as several non-V1 devices now use the *-v1.dtsi,
the *cpe510-v1.dts does not use the cpe510.dtsi, etc.

This introduces a new naming scheme based on whether devices have
one or two ports, which should be easier to grasp.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-23 12:03:49 +01:00
Adrian Schmutzler
640a36aafc ath79: DTS style improvement for Ubiquiti XM and BZ devices
This applies minor style improvements and removes commented pll
clock adjustments from ubnt_xm DTSI. The latter were introduced
(already commented out) when adding ath79 target and have never
been touched since then. For Unifi (BZ board), similar clock
adjustments are employed and used.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-23 11:57:48 +01:00
Andrew Cameron
20fdfe37d2 ath79: add support for the TP-LINK WBS510 V1
This adds support for a popular low-cost 5GHz N based AP

Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
2019-11-22 11:41:27 +01:00
Andrew Cameron
5b8709d9f2 ath79: add support for the TP-LINK WBS510 V2
This adds support for a popular low-cost 5GHz N based AP

Specifications:
 - SoC: Atheros AR9344
 - RAM: 64MB
 - Storage: 8 MB SPI NOR
 - Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
 - Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
2019-11-22 11:41:24 +01:00
Adrian Schmutzler
317e98a5a2 ath79: add PoE passthrough switch for Ubiquiti Nanostation (XM/XW)
This adds the gpio switch to enable PoE passthrough on Ubiquiti
Nanostation (XM/XW).

Values are copied from the implementation in ar71xx.

GPIO values checked on:
- NanoStation M5 XW
- NanoStation M2 XM

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-21 12:26:05 +01:00
Adrian Schmutzler
1a0d6e1eba ath79: fix DTS node names for Ubiquiti XM partitions
Some node names were inconsistent with the reg property. Fix it.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-19 00:16:48 +01:00
Christian Lamparter
7a7610c21b ath79: remap D-Link DIR-859 A1 WPS button to WPS
The WPS button was mapped to the restart/reset. This patch
changes it to emit the KEY_WPS_BUTTON keycode so pressing
the WPS button does initiate WPS.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-11-16 22:42:07 +01:00
Jeff Kletsky
f84d6d2f3a ath79: fix firmware partition attributes for GL-AR300M16 and -Lite
During the introduction of the ath79/nand images for the GL-AR300M
series the firmware partition label and compatible were altered,
but the necessary adjustments have not been made for the
GL-AR300M16 and the GL-AR300M-Lite. This will result in a
non-bootable partition setup for these devices.

This patch adds the necessary definitions to those two devices.

Fixes: 55e6c903ae ("ath79: GL-AR300M: provide NAND support;
       increase to 4 MB kernel")
Fixes: b591cabd39 ("ath79: add GL.iNet GL-AR300M16 as NOR-only
       board")

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
[extend commit message, alter commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-16 02:41:13 +01:00
Adrian Schmutzler
fc44a8481c ath79: fix sysupgrade from ar71xx for WNDR3700 V2 and WNDR3800(CH)
ar71xx has just one board name "wndr3700" for WNDR3700 V1/V2,
WNDR3800 and WNDR3800CH, whereas ath79 provides separate images for
the boards. So, update SUPPORTED_DEVICES to store the correct
ar71xx board names.

Fixes: FS#2510

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-14 23:14:35 +01:00
Paul Blazejowski
7e623c3128 ath79: add support for Netgear WNDR3700v4
This patch adds ath79 support for Netgear WNDR3700v4.
Router was previously supported by ar71xx target only.
Note: device requires 'ar934x-nand' driver in kernel.

Specification
=============
  * Description: Netgear WNDR3700v4
  * Loader: U-boot
  * SOC: Atheros AR9344 (560 MHz)
  * RAM: 128 MiB
  * Flash: 128 MiB (NAND)
    - U-boot binary: 256 KiB
    - U-boot environment: 256 KiB
    - ART: 256 KiB
    - POT: 512 KiB
    - Language: 2 MiB
    - Config: 512 KiB
    - Traffic Meter: 3 MiB
    - Firmware: 25 MiB
    - ART Backup: 256 KiB
    - Reserved: 96 MiB
  * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8327)
  * Wireless:
    - 2.4 GHz b/g/n (internal)
    - 5 GHz a/n (AR9580)
  * USB: yes, 1 x USB 2.0
  * Buttons:
    - Reset
    - WiFi (rfkill)
    - WPS
  * LEDs:
    - Power (amber/green)
    - WAN (amber/green)
    - WLAN 2G (green)
    - WLAN 5G (blue)
    - 4 x LAN (amber/green)
    - USB (green)
    - WPS (amber/green)
  * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
  * Power supply: DC 12V 2.5A
  * MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2

Installation
============
  * TFTP recovery
  * TFTP via U-boot prompt
  * sysupgrade
  * Web interface

Note about partitioning: firmware partition offset (0x6c0000) is
hardcoded into vendor's u-boot, so this partition cannot be moved
and resized to include Netgear-specific flash areas (pot, language,
config, traffic_meter) not used by OpenWrt.

Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_nand=y
CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr3700-v4=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y

Signed-off-by: Paul Blazejowski <paulb@blazebox.homeip.net>
2019-11-14 23:14:15 +01:00
Michal Cieslakiewicz
119e0d57ae ath79: split dts file for Netgear WNDR4300
Move board configuration to dtsi file in preparation for WNDR3700v4
router support.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-11-14 23:13:49 +01:00
Adrian Schmutzler
71fbec0eff ath79: fix indent in TP-Link TL-WDR4900 v2 DTS
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-14 23:13:19 +01:00
Adrian Schmutzler
bcee364944 ath79: improve common DTSI name for TP-Link Archer C5, C7 v1/v2
As the former qca9558_tplink_archer-c7.dtsi is also used for
Archer C5 v1 this patch removes the number from the DTSI name
to indicate that.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-14 23:12:48 +01:00
Petr Štetiar
fa83455392 ath79: remove obsolete OF PCI related config symbols
Those symbols were removed in kernel 4.16:

 commit 4670d610d59233b017a6ea1fa25bbf06dabbff42
 Author:     Rob Herring <robh@kernel.org>

    PCI: Move OF-related PCI functions into PCI core

Fixes: FS#2588
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-11-14 22:53:31 +01:00
Roger Pueyo Centelles
1c6066a867 ath79: include rssileds package for ubnt devices with LEDs
Some Ubiquiti devices had the RSSI LEDs configured in 01_leds but
were missing the rssileds package, while others that don't have
RSSI LEDS had the package included.

This commit includes the rssileds package only for those devices
that need it.

Tested on a NanoStation M XW.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-11-14 16:03:33 +01:00
Jeff Kletsky
b496a2294c ath79: GL-AR750S: provide NAND support; increase kernel to 4 MB
The GL.iNet GL-AR750S has been supported by the ar71xx and ath79
platforms with access to its 16 MB NOR flash, but not its 128 MB
SPI NAND flash.

This commit provides support for the NAND through the upstream
SPI-NAND framework.

At this time, the OEM U-Boot appears to only support loading the
kernel from NOR. This configuration is preserved as this time,
with the glinet,gl-ar750s-nand name reserved for a potential,
future, NAND-only boot.

The family of GL-AR750S devices on the ath79 platform now includes:

  * glinet,gl-ar750m-nor-nand   "nand" target
  * glinet,gl-ar750m-nor        "nand" target (NAND-aware)

NB: This commit increases the kernel size from 2 MB to 4 MB

"Force-less" sysupgrade is presently supported from the current
versions of following NOR-based firmwre images to the version of
glinet,gl-ar750s-nor firmware produced by this commit:

  * glinet,gl-ar750s     -- OpenWrt 19.07 ar71xx
  * glinet,gl-ar750s     -- OpenWrt 19.07 ath79

Users who have sucessfully upgraded to glinet,gl-ar750m-nor may then
flash glinet,gl-ar750m-nor-nand with sysupgrade to transtion to the
NAND-based variant.

Other upgrades to these images, including directly to the NAND-based
glinet,gl-ar750s-nor-nand firmware, can be accomplished through U-Boot.

NB: See "ath79: restrict GL-AR750S kernel build-size to 2 MB" which
enables flashing of NAND factory.img with the current GL-iNet U-Boot,
"U-Boot 1.1.4-gcf378d80-dirty (Aug 16 2018 - 07:51:15)"

The GL-AR750S OEM U-Boot allows upload and flashing of either NOR
firmware (sysupgrade.bin) or NAND firmware (factory.img) through its
HTTP-based GUI. Serial connectivity is not required.

The glinet,gl-ar750s-nor and glinet,gl-ar750s-nor-nand images
generated after this commit flash each other directly.

This commit changes the control of the USB VBUS to gpio-hog from
regulator-fixed introduced by commit 0f6b944c92. This reduces the
compressed kernel size by ~14 kB, with no apparent loss of
functionality. No other ath79-nand boards are using regulator-fixed
at this time.

Note: mtd_get_mac_binary art 0x5006 does not return the proper MAC
and the GL.iNet source indicates that only the 0x0 offset is valid

The ar71xx targets are unmodified.

Cc: Alexander Wördekemper <alexwoerde@web.de>

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-11-14 14:38:58 +08:00
Jeff Kletsky
b591cabd39 ath79: add GL.iNet GL-AR300M16 as NOR-only board
The GL.iNet GL-AR300M series of devices includes variants without NAND
and only the 16 MB NOR flash. These include the GL-AR300M16 and the
GL-AR300M-Lite (already with its own board name).

This board-name addition provides disambiguation from the NAND-bearing
GL-AR300M devices, both for OpenWrt code and for end users.

Kernel and firmware support for NAND and UBI will add ~320 kB to the
overall firmware size at this time. This NOR-only option continues to
provide more compact firmware for both the GL-AR300M16 as well as
those who wish to use it as an alternate or primary, NOR-resident
firmware on the GL-AR300M.

The ar71xx targets are unmodified.

Installation
------------

Install through OEM U-Boot (HTTP-based) or `sysupgrade --force` when
booted from NOR and running OEM or OpenWrt, NOR-based firmware.

As one of the intentions is disambiguation from NAND-bearing units,
users who have flashed this firmware onto a device with NAND would
need to use U-Boot or `sysupgrade --force` to flash firmware that
again supports NAND.

There are no additional SUPPORTED_DEVICES as it is not possible to
determine if a device does or does not have NAND based on
either the OEM's or OpenWrt's board names prior to this patch.

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-11-14 14:38:58 +08:00
Jeff Kletsky
55e6c903ae ath79: GL-AR300M: provide NAND support; increase to 4 MB kernel
The GL.iNet GL-AR300M has been supported by the ar71xx and ath79
platforms with access to its 16 MB NOR flash, but not its 128 MB
SPI NAND flash.

This commit provides support for the NAND through the upstream
SPI-NAND framework. Devices with both NOR and NAND flash can support
independent firmware on each, with U-Boot able to boot from either.
The OEM U-Boot will fall back to the NOR firmware after three
"unsuccessful" boots.

The family of GL-AR300M devices on the ath79 platform now includes:

  * glinet,gl-ar300m-lite       "generic" target, NOR-only board
  * glinet,gl-ar300m-nand       "nand" target
  * glinet,gl-ar300m-nor        "nand" target (NAND-aware)

NB: This commit increases the kernel size from 2 MB to 4 MB

"Force-less" sysupgrade is presently supported from the current
versions of following NOR-based firmwre images to the version of
glinet,gl-ar300m-nor firmware produced by this commit:

  * gl-ar300m            -- OEM v3 NOR    ar71xx (openwrt-ar300m16-*.bin)
  * gl-ar300m            -- OpenWrt 18.06 ar71xx
  * gl-ar300m            -- OpenWrt 19.07 ar71xx

Other upgrades to these images should be performed through U-Boot.

The GL-AR300M OEM U-Boot allows upload and flashing of either NOR
firmware (sysupgrade.bin) or NAND firmware (factory.img) through its
HTTP-based GUI. Serial connectivity is not required.

The glinet,gl-ar300m-nand and glinet,gl-ar300m-nor images generated
after this commit should safely flash each other using sysupgrade.

The boot counter is implemented by the OEM using u-boot-env. At this
time, it does not appear that the switch on the side of the unit can
be used to select NOR vs. NAND boot and the fail-over is only from
NAND to NOR. To save flash wear, it is only reset when running the
glinet,gl-ar300m-nand firmware.

NAND-specific base-files are used to remove impact on existing
generic and tiny targets.

As there is now no "generic" build appropriate for the GL-AR300M16,
(or for users of the GL-AR300M that do not need access to NAND)
it will be introduced in a subsequent commit.

Note: `mtd_get_mac_binary art 0x6` does not return the proper MAC
and the GL.iNet source indicates that only the 0x0 offset is valid

The ar71xx targets are unmodified.

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-11-14 14:38:58 +08:00
Jeff Kletsky
20b3e77ba3 ath79: prepare NAND subtarget for upstream support of SPI NAND
Linux 4.19 supplies the upstream spi-nand framework,
permitting porting and support of boards with SPI NAND.

  * Adjusted nand/target.mk to provide FEATURES += squashfs nand

  * Updated config-default to provide current MTD and UBI support

Defaults selected for:

  CONFIG_MTD_UBI_WL_THRESHOLD=4096
  CONFIG_MTD_UBI_BEB_LIMIT=20
  # CONFIG_MTD_UBI_FASTMAP is not set
  # CONFIG_MTD_UBI_GLUEBI is not set

The bad-block reservation limit technically should be 21 for Paragon
SPI NAND but most other devices in the class are 20 blocks per Gbit.
In Linux 5.2 this is specified on a per-chip basis through NAND_MEMORG

Contents adjusted to remove declarations provided at the target level
by commit 08a134820f (Oct 23, 2019) ath79: enable PCI for whole target

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Tested-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-11-14 14:38:58 +08:00
Adrian Schmutzler
d421a8b944 ath79: read label MAC address from flash instead of using phy0/phy1
This replaces all uses of $(cat /sys/class/ieee80211/phyX/macaddress)
by retrieval from the proper flash locations. This will make
02_network independent of WiFi setup again.

For future reference:

The MAC addresses of the FRITZ!WLAN Repeater 300E can be extracted
from the urlader key value store:

maca        *:6B
macb        *:6C
macwlan     *:6D
macdsl      *:6E

and be set by e.g.
addr=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-13 12:55:25 +01:00
Adrian Schmutzler
b5791118cc ath79: fix SUPPORTED_DEVICES for TP-Link TL-WR1043ND v3
In ar71xx, the board name for the TL-WR1043ND v3 is equal to v2:
tl-wr1043nd-v2

Fix SUPPORTED_DEVICES for v3 in ath79 accordingly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-11 19:03:20 +01:00
Adrian Schmutzler
5dc535419f ath79: fix identifier for Nanostation M in ath9k caldata extraction
When Nanostation M was renamed from ubnt,nano-m to ubnt,nanostation-m
in commit f1396ac753 ("ath79: align naming of Ubiquiti Nanostation M"),
the caldata extraction in 10-ath9k-eeprom was overlooked.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-11 00:33:34 +01:00
Adrian Schmutzler
4176100b06 ath79: replace generic button node names
In several DTS files, button nodes are just named buttonX or
xxx_button. This replaces the names with more specific names matching
the majority of key definitions.

While at it, fix name of keys node in one case.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-07 17:13:18 +01:00
Adrian Schmutzler
c8c4f7216e ath79: specify N and ND subversions of TL-WR941 with ALT0_MODEL
TP-Link's TL-WR941 is sold with detachable antennas
internationally (ND version), but with fixed antennas in China
(N version). While hardware and images are similar for both
variants of v2 and v4, they are different for v6.

Having both explicitly will make it easier for user to identify
the correct image, and most importantly will raise awareness
that N and ND are not necessarily always the same as for
TL-WR841 series.

With an image selection webpage, using ALT0_MODEL as in this
patch will provide the option to list versions for N and ND
separately.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 15:04:05 +01:00
Adrian Schmutzler
15dc60e727 ath79: move eth0 to parent DTSI for ar9344 TP-Link CPE devices
The &eth0 node is the same for all TP-Link CPE devices in ar9344,
so move it to parent DTSI. While at it, do some minor DTS
harmonizations.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 13:51:20 +01:00
Andrew Cameron
bae0d47f2e ath79: add support for the TP-LINK CPE220 V3
This adds support for a popular low-cost 2.4GHz N based AP

Specifications:
SoC: Qualcomm Atheros QCA9533 (650MHz)
RAM: 64MB
Storage: 8 MB SPI NOR
Wireless: 2.4GHz N based built into SoC 2x2
Ethernet: 2x 100/10 Mbps, integrated into SoC

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

This also applies some minor changes to the common DTSI:
- use &wmac for label-mac-device, as this one is actually set up in
  common DTSI
- move &eth0 to parent DTSI
- fix several leading spaces, added/removed newlines

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[DTS style fixes/improvements, updated commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 13:37:40 +01:00
Adrian Schmutzler
f4026ad24d ath79: DTS file style update and harmonization
This applies several style adjustments that have been requested in
recent reviews to older DTS files. Despite making the code base more
consistent, this will also help to reduce review time when DTSes
are copy/pasted.

Applied changes:
- Rename gpio-keys/gpio-leds to keys/leds
- Remove node labels that are not used
- Use label property for partitions
- Prefix led node labels with "led_"
- Remove redundant includes
- Harmonize new lines after status property
- Several smaller style fixes

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 00:27:55 +01:00
Adrian Schmutzler
443ba75c4e ath79: fix sorting and harmonize indent in tiny board.d files
This seems to have been overlooked when splitting base files.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-05 13:14:29 +01:00
Bernhard Geier
3930aab2cb ath79: add support for TP-Link WBS210 v2
TP-Link WBS210 v2 is an outdoor wireless CPE for 2.4 GHz with
two Ethernet ports based on Atheros AR9344

The device is the same as TP-Link CPE220 v2, but with higher TX power (27 dBm
instead of 12 dBm) and two antenna connectors instead of built-in antennas.

Specifications:
 - SoC: Atheros AR9344
 - RAM: 64MB
 - Storage: 8 MB SPI NOR
 - Wireless: 2.4GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
 - Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP: 192.168.0.100
Stock device TFTP adress: 192.168.0.254

The TP-Link WBS devices use the same GPIOs as the CPE devices,
except for the link4 LED. For this one, WBS devices use "2", while
CPE devices use "16". (Tested on WBS210 v2)

Signed-off-by: Bernhard Geier <freifunk@geierb.de>
[added comment about GPIO]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 13:59:18 +01:00
Adrian Schmutzler
fe534392a5 ath79: revert erroneous second addition of files for WNDR4300
There are two recent commits stating to add support for Netgear
WNDR4300, where the second one seems to be just leftover from
an earlier patch having been rebased.

Since the first patch already provides support in the most recent
state, just revert the second one.

This reverts commit cd87272eb2.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 00:46:59 +01:00
Rasim Kalimullin
81f7af4881 ath79: add support for TP-Link TL-WR1045ND v2
Specifications:
 - QCA9558 Soc
 - 720/800 (CPU/DDR)
 - 1x 10/100/1000 Mbps WAN Ethernet
 - 4x 10/100/1000 Mbps LAN Ethernet
 - 64 MB RAM (DDR2)
 - 8 MB FLASH
 - QCA9558 2.4 GHz 802.11bgn
 - 1x USB 2.0

Flash instruction
WebUI:
Download *-factory.bin image, rename to tp_firmware.bin and upload
it via the firmwary upgrade function of the stock firmware WebUI.

Tftp:
Rename OpenWRT or original firmware to wr1045v2_tp_recovery.bin and
Change your computer ip in 192.168.0.66 and subnet mask in 255.255.255.0.
Router will obtain IP 192.168.0.86 for a few seconds while loading,
when reset button pressed at power On.

Signed-off-by: Rasim Kalimullin <neutrino.vm@gmail.com>
[rebased onto base-files split]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 00:29:55 +01:00
Roger Pueyo Centelles
20ace70db6 ath79: remove wmac mtd-mac-address for UniFi AC family
The MAC address for the wmac 2.4 GHz radio of the Ubiquiti UniFi AC
family of devices is actually embedded in the mtd-cal-data, so there
is no need for mtd-mac-address (which was incorrectly forcing wmac
to have the same MAC as eth0). This makes it coherent with the stock
firmware and the ar71xx target:

 · XX:XX:XX:X0:XX:XX eth0
 · XX:XX:XX:X1:XX:XX ath0/wlan1 (2.4 GHz)
 · XX:XX:XX:X2:XX:XX ath1/wlan0 (5 GHz)

Checked on a UniFi AC Mesh, a UniFi AC LR and a UniFi Lite.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-11-03 00:29:40 +01:00
Adrian Schmutzler
194612997b ath79: use nand_do_upgrade by default for nand subtarget
On nand subtarget, the default upgrade mechanism should be
nand_do_upgrade. This patch changes platform_do_upgrade()
accordingly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 00:29:12 +01:00