This adds support for the various clones of the TL-WA830RE recently
supported in fb99ac6807 ("ath79: add support for TP-Link TL-WA830RE v1"):
- tplink,tl-wa701nd-v1
- tplink,tl-wa730re-v1
- tplink,tl-wa801nd-v1
- tplink,tl-wa830re-v1 (already supported)
- tplink,tl-wa901nd-v1
Since these devices are 100%-clones in ar71xx, this patch adds all
of them without run-testing (as this has been done for TL-WA830RE v1).
Specifications:
- SOC: Atheros AR7240
- CPU: 400MHz
- Flash: 4 MiB (Spansion S25FL032P)
- RAM: 32 MiB (Zentel A3S56D40FTP-G5)
- WLAN: Atheros AR9280 bgn 2x2
- Ethernet: 1 port (100M)
Flash instructions:
- install from u-boot with tftp (requires serial access)
> setenv ipaddr a.b.c.d
> setenv serverip e.f.g.h
> tftpboot 0x80000000 \
openwrt-ath79-tiny-tplink_tl-waxxxxx-v1-squashfs-factory.bin
> erase 0x9f020000 +0x3c0000
> cp.b 0x80000000 0x9f020000 0x3c0000
> bootm 0x9f020000
- flash factory image from OEM WebUI
- sysupgrade from ar71xx image
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Several devices with tplink-safeloader contain default values (0x0)
for TPLINK_HWID and TPLINK_HWREV in their device definitions.
Move those to common tplink-safeloader definition so they do not
have to be repeated each time.
While at it, set default value for tplink-v1 and tplink-v2 as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The TL-WR940N v6 is similar to v3/v4, it just has different
LEDs and MAC address assignment.
Specification:
- 750 MHz CPU
- 32 MB of RAM
- 4 MB of FLASH
- 2.4 GHz WiFi
- 4x 10/100 Mbps Ethernet
The use of LEDs is based on ar71xx, so blue LED is used for WAN
and orange LED for diag (boot/failsafe/etc.).
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to
wr940nv6_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Thanks to Manuel Kock for reviewing and testing this patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Manuel Kock <github.web@manu.li>
This ports support for the TL-WA830RE v1 range extender from ar71xx to
ath79.
Specifications:
- SOC: Atheros AR7240
- CPU: 400MHz
- Flash: 4 MiB (Spansion S25FL032P)
- RAM: 32 MiB (Zentel A3S56D40FTP-G5)
- WLAN: Atheros AR9280 bgn 2x2
- Ethernet: 1 port (100M)
Flash instructions:
- install from u-boot with tftp (requires serial access)
> setenv ipaddr a.b.c.d
> setenv serverip e.f.g.h
> tftpboot 0x80000000 \
openwrt-ath79-tiny-tplink_tl-wa830re-v1-squashfs-factory.bin
> erase 0x9f020000 +0x3c0000
> cp.b 0x80000000 0x9f020000 0x3c0000
> bootm 0x9f020000
- flash factory image from OEM WebUI
- sysupgrade from ar71xx image
The device seems to be a clone of the following devices not yet
added to ath79:
- tl-wa701nd-v1
- tl-wa730re-v1
- tl-wa801nd-v1
- tl-wa901nd-v1
Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
[make use of ar7240_tplink.dtsi, add note about clones]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Based on a script for comparison, this fixes (hopefully) all errors
in SUPPORTED_DEVICES for ar71xx->ath79 upgrade.
Devices where old string is removed as the device does not exist
in ar71xx:
- dlink_dir-859-a1
- tplink_archer-a7-v5
- tplink_cpe510-v3
Devices where string is changed because it did not match the board
name in ar71xx:
- tplink_tl-mr3220-v1
- tplink_tl-mr3420-v1
- tplink_tl-wr2543-v1
- tplink_tl-wr741nd-v4
- tplink_tl-wr841-v7
- ubnt_unifiac-mesh
- ubnt_unifiac-mesh-pro
- ubnt_unifiac-pro
For this device, the correct string could not be found, but we could
not determine the correct one. Thus, the string is removed for now:
- tplink_tl-wr740n-v4
The script for checking this is quite simple (note that newer
entries, i.e. ath79->ath79 upgrade, are displayed as missing):
newpath=target/linux/ath79/image/
oldpath=target/linux/ar71xx/base-files/lib/ar71xx.sh
for s in $(grep -roh "SUPPORTED_DEVICES.*" $newpath | sed 's/SUPPORTED_DEVICES *.= *//'); do
found="Missing"
grep -q -r "\"$s\"" $oldpath && found="Found"
echo "$s: $found."
done
The errors might be filtered by appending 'grep "Missing"' to the script.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB
Flash instruction: use "factory" image directly in vendor GUI.
Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.
You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin
Stock firmware uses label MAC address for WiFi and same with local
bit set for ethernet. Since this is difficult to reproduce with
the toolset of OpenWrt, we just keep both ethernet and WiFi to
the same address here.
This is the first tiny device with tplink-safeloader in ath79.
Firmware partition is only 3648k and thus even smaller than for
the tplink-4m(lzma) devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This ports support for the TL-WA850RE v1 range extender from ar71xx
to ath79.
Specifications:
Board: AP123 / AR9341 rev. 3
Flash/RAM: 4/32 MiB
CPU: 535 MHz
WiFi: 2.4 GHz b/g/n
Ethernet: 1 port (100M)
Flashing instructions:
Upload the factory image via the vendor firmware upgrade option.
Recovery:
Note that this device does not provide TFTP via ethernet like many
other TP-Link devices do. You will have to open the case if you
require recovery beyond failsafe.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This move the slightly different target-specific implementations of
mktplinkfw from the targets to include/image-commands.mk and renames
it to tplink-v1-image. Having a common version will increase
consistency between implementation and will complete the
tplink build command already present in the new location.
Due to the slight differences of the original implementations, this
also does some adjustments to the device build commands/variables.
This also moves rootfs_align as this is required as dependency.
Tested on:
- TL-WDR4300 v1 (ath79, factory)
- TL-WDR4900 v1 (mpc85xx, sysupgrade)
- RE210 v1 (ramips, see Tested-by)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Christoph Krapp <achterin@googlemail.com>
TP-Link's TL-WR941 is sold with detachable antennas
internationally (ND version), but with fixed antennas in China
(N version). While hardware and images are similar for both
variants of v2 and v4, they are different for v6.
Having both explicitly will make it easier for user to identify
the correct image, and most importantly will raise awareness
that N and ND are not necessarily always the same as for
TL-WR841 series.
With an image selection webpage, using ALT0_MODEL as in this
patch will provide the option to list versions for N and ND
separately.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This fixes the remaining IMAGE_SIZE issues in ath79 target.
All devices in target have been checked, so together with
previous patches this target should be "clean" afterwards.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This removes _all_ occurrences of kmod-usb-core from
DEVICE_PACKAGES and similar variables.
This package is pulled as dependency by one of the following
packages in any case:
- kmod-usb-chipidea
- kmod-usb-dwc2
- kmod-usb-ledtrig-usbport
- kmod-usb-ohci
- kmod-usb2
- kmod-usb2-pci
- kmod-usb3
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[remove kmod-usb-core from EnGenius ESR600]
Signed-off-by: David Bauer <mail@david-bauer.net>
This applies alphabetic sorting to devices in image/* files.
For certain cases, this patch deviates from strict sorting, e.g.
to ensure that v10 comes after v9.
While at it, fix an indent and remove some useless empty lines.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: ar9341
- RAM: 32M
- Flash: 4M
- Ethernet: 5x FE ports
- WiFi: ar9341-wmac
Flash instruction:
Upload generated factory firmware on vendor's web interface.
This changes the key assignment compared to ar71xx support of this
device, since of the two keys on the device one is used as combined
Reset/WPS and the second one as WiFi on/off button.
Despite, the reset button required GPIO_ACTIVE_HIGH to work correctly.
Signed-off-by: Lim Guo Wei <limguowei@gmail.com>
[redo commit message]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This adds support for several TP-Link devices based on TP9343
("a QCA9561 without PCIe and USB"):
- TL-WR940N v3
- TL-WR940N v4
- TL-WR941ND v6
The devices are only different concerning LEDs and MAC address
assignment.
All TL-WR940 are with non-detachable antennas (N), all
TL-WR941 devices are with detachable antennas (ND).
Specification:
- 750 MHz CPU
- 32 MB of RAM
- 4 MB of FLASH
- 2.4 GHz WiFi
- 4x 10/100 Mbps Ethernet
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to * (see below)
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
* TFTP image names:
940 v3: wr941ndv6_tp_recovery.bin
940 v4: wr940nv4_tp_recovery.bin
941 v6: wr941ndv6_tp_recovery.bin
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This router has the same hardware as TP-LINK TL-WR841N/ND v11 (same
FCC ID, same TFTP image name...).
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to wr841nv11_tp_recovery.bin
(it's really v11, not v12)
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The TL-WR841N/ND v10 is mostly identical to the v9. Apart from some minor
changes, it contains a newer revision of the QCA9533 SoC and the CPU clock
is significantly higher.
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to wr841nv10_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and
DEVICE_VARIANT. All three are merged together to look the same as the
current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as
a *fallback* for devices which weren't upgraded yet.
This is based on the work of @sudhanshu16.
The motivation is to create JSON files based on provided metadata,
needing clear differentiation between vendor, model and revision.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This adds support for the Chinese version of TL-WR941N v7.
It uses QCA9558+AR8236 while the international version
uses TP9343 instead.
Specification:
- SoC: Qualcomm Atheros QCA9558
- Flash: 4 MB
- RAM: 64 MB
- Ethernet: Atheros AR8236 with 5 FE ports
Flash instruction:
Upload the generated factory firmware on web interface.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
CPU: Atheros AR9341 535MHz
RAM: 32MB
FLASH: 4MiB
PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan
WiFi: Atheros AR9341 2x2:2 bgn
LED: Power (static on), LAN (controlled by Switch), WAN, SYS, WiFi, RFKill
BTN: WPS, WiFi, Reset
Installation:
Upload the factory image via the vendor-GUI.
Signed-off-by: Antonio Silverio <menion@gmail.com>
[resolve merge conflicts, squash commits, fix commit title, remove
default default off led properties, mark sysupgrade image compatible
with the ar71xx version of the board, drop blank lines from dts]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This commit adds support for the TP-Link TL-WR901ND v2 access point.
CPU: Atheros AR9132 400MHz
RAM: 32MB
FLASH: 4MiB
WiFi: Atheros AR9103 3x3:2 bgn
LED: Power (static on)
LAN (controlled by PHY)
SYS, WiFi, QSS toggleable
BTN: Reset, QSS
Installation:
Upload the factory image via the vendor-GUI.
Signed-off-by: David Bauer <mail@david-bauer.net>
Sysupgrading to ath79 from ar71xx currently fails because of mismatching
supported_devices. ar71xx is expecting "tl-mr3020" which is missing in
the ath79 image. Upgrading from ath79 is unaffected, as the image
contains the old string for ar71xx and the new one coming from the
device-tree.
Signed-off-by: David Bauer <mail@david-bauer.net>
Remove SUPPORTED_DEVICES from wr841-v9 because it´s not needed and
for consistency rename everything to tl-wr841-v9.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
This patch did the following things:
1. Separate ath9k-leds out of gpio leds so that all other leds will work
before ath9k loded (e.g. during preinit/init stage).
2. Rename wps led to qss since that's how TP-Link mark it.
3. Rename LED prefix to tp-link because that dts is shared by many devices.
4. Rename to wr740n-v1 because v1 is the first and v2 just use the fw of v1.
(This will require a forced sysupgrade if you comes from
the previous wr740n v2 image.)
5. Remove SUPPORTED_DEVICES.
(tl-wr740n-v2 doesn't exist anywhere so it's useless.)
6. Add all WR741ND v1 clones found in ar71xx.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This patch ports the TP-Link TL-WR741ND v4 and TL-WR740ND v4 to the
ath79 target.
Because the two devices share the same hw layout, this patch adds a common
.dtsi which is included by the two .dts.
Signed-off-by: Rocco Folino <rocco@folino.io>
