This change makes it possible to configure the wan/dsl ppp interface
settings independantly from the used TC-Layer (ATM/PTM).
Now you can move a device from an ADSL/ATM port to an VDSL/PTM port
without any configuration changes for example.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[use the dsl0 interface name for the default netdev trigger in 01_led,
add ip dependency]
Signed-off-by: Mathias Kresin <dev@kresin.me>
If xfer_mode is set to auto the vdsl_cpe_control daemon assumes that
ATM should be used for ADSL and PTM for VDSL.
xfer_mode and line_mode can be set to fixed value independantly from
each other.
The syntax for the tc_layer argument of vdsl_cpe_control is as follow:
-T<TcADSL>:<TcCfgUsADSL>:<TcCfgDsADSL>_<TcVDSL>:<TcCfgUsVDSL>:<TcCfgDsVDSL>
where TcADSL and TcVDSL can be: 1=ATM, 2=PTM/EFM, 4=Auto TC-Layer
and TcCfgUsADSL, TcCfgUsVDSL, TcCfgDsADSL, TcCfgDsVDSL can be:
1=64/65-octet encapsulation supported
2=64/65-octet encapsulation with pre-emption
3=64/65-octet encapsulation with short packets
Default: In case of no '-T' option is given, ADSL will be configured
in ATM and VDSL in PTM/EFM: -T1:0x1:0x1_2:0x1:0x1
The '-M' argument of dsl_cpe_control defines the initial DSL mode
(NextMode) for ADSL/VDSL multimode handling.
Possible Values: 0=API-default, 1=ADSL, 2=VDSL
Default: In case of no '-M' option is given, '0' (API-default) will
be selected.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
The esi call was added to workaround a race condition between applying
a configured mac address to the wan interface and starting the protocol
(handler) as it was observed in a DHCP over ATM bridge configuration.
Martin Schiller, TDT GmbH was so kind to test with their local
infrastructure if the race condition still exists. The provided package
dumps captured behind the DSLAM shows that it doesn't. It was most
likely fixed with adding carrier support to the lantiq ptm/atm driver.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This is necessary for devices using the PSB80108/VRX220LD front-end
(currently only known on the Netgear DM200).
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
This patch makes possible to tweak the downstream SNR margin on
Lantiq DSL devices.
The UCI parameter 'network.dsl.ds_snr_offset' is used to set the SNR
margin offset. It accepts values in range -50 to +50 in 0.1 dB units.
The SNR margin can thus be modified in range -5.0 to +5.0 dB in 0.1 dB
steps.
Currently this should only affect ADSL (not VDSL). It should be very
easy to make this work also on VDSL lines, but since I couldn't test
on VDSL lines this patch does not do that yet.
I have also a patch for LUCI about this, that I could submit.
Tested on FB3370 (Lantiq VR9) and Telecom Italia ADSL2+ line.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Add nonshared flag to package depending on specific targets or subtargets as
there's no guarantee otherwise that they'll be available in the shared repo.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
I do not know if this causes any problems now, but we should not set
it, because it is reserved. Some more recent versions of the Lantiq DSL
API driver and Control is checking if only valid bits are set.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48948
There are some cases where ISPs are running ATM over VDSL or PTM over
ADSL, this is not the common case, but these cases exist. Make it
possible to configure OpenWrt for such cases by adding a new config
option line_mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48947
The detailed annex option were only available in the danube DSL app
including the activation of G.992.2 Annex A (ADSL Lite). This is now
also added to the vdsl app for the vrx200.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48946
I am not calling dsl_cmd because I want to ignore the lock, quit
should also be send when someone else is accessing it. I saw that some
other call was stuck here and all following calls were stuck in the
dsl_cmd lock.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48943
Before r47933 Bit 1 (first bit) of xTSE Octet 1 (first octet) defaulted
to 1, which allowed T1.413 to operate.
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
SVN-Revision: 48763
Add back a slightly modified version of the lowlevel settings which
where removed with r46920.
In compare to the old lowlevel settings, the B43c tone is added to
tone_adsl_b and tone_adsl_bv.
If an unsupported tone value is used, the auto probing mode is used, in
compare to the fallback to tone_adsl_av and tone_vdsl_av with the old
lowlevel settings.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48054
According to ITU-T G.997.1 Amendment 2 (04/2013) section 2.1, bit 3 of
XTSE octet 8 either allow or denies the initialization of G.993.5.
Even if the current redistributable xDSL firmware doesn't include
G.993.5 vectoring support, enable this bit by default to allow people to
get their G.993.5 line working using a custom xDSL firmware.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48053
r47933 revealed that the driver/app in combination with the chosen
firmware does a good job in selecting a working xtse.
Use this probing mode if no annex is specified.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48052
This patch adds the missing VDSL2 bits to the annex specific XTSE (like
it should be according to the comments above the XTSE bits).
Since r47933 it's mandatory to remove the annex option to switch to
VDSL2 (only) operation mode.
As shown by ticket #21436 and a few mails I received personally, even
experienced users are not aware that they have to remove the annex
option to get their VDSL2 line working and as shown by this patch it
doesn't need to be that "complicated".
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48051
- CONFIG_IFX_CLI is unused, couldn't find any reference to this config variable
- use disable-feature instead of enable-feature=no
- reorder configure args to have depending args together
- remove configure args which set the default value
- group enable-model and configure args which enable or disable features that
are covered by the feature set
The config.log contains the same values as before. The vdsl_cpe_control binary
has the same checksum as before.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47888
The typicial feature set doesn't include "DSL PM showtime counters support"
(INCLUDE_DSL_CPE_PM_SHOWTIME_COUNTERS). This feature provides the
vdsl_cpe_control command 'pmccsg', which is used by 'dsl_control status' to get
the line uptime.
The binary size increases to 103912 byte (+4256 byte) uncompressed.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47887
Use the 'typical' compile configuration instead of 'full', which most
notably excludes the soap support.
/sbin/vdsl_cpe_control shrinks down to ~50%, from 178kb(!) to 90kb.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 47769
In this upstream dsl driver app version the autoboot is deactivated activate
it again.
In addition to the update this also fixes some build warnings and makes it
use the same configure option as used in Lantiq UGW.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
SVN-Revision: 47637
Thanks to Sylwester Petela for testing my patch (successfully on an
ADSL connection) and for pointing out some configuration mistakes.
Others (including me) have also successfully tested this extensively
on VDSL connections.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46920
I had to use a VDSL-only tone-setup to get show-time.
Handle this in uci by checking if annex is unset.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43114
the IB tries to run the enable target on all init.d scripts.
It fails when including the dsl_control helper. Check for existence
prior to the include.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41787
* atm module needs to be loaded before linux-atm
* use absolute firmware paths
* extended validation
* add a script for mounting an optional firmware partition
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40460
