The USB PHY on the ar9330 and similar SoCs needs the PHY driver. In
OpenWrt 23.05 it was compiled into the kernel. The kernel 6.6
configuration does not compile it in any more, make the
kmod-usb-chipidea driver select it to add it to the images.
Fixes: https://github.com/openwrt/openwrt/issues/17710
Fixes: 04bdf9b3323e ("ath79: disable ath79 USB phy drivers by default")
Link: https://github.com/openwrt/openwrt/pull/17720
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These symbols are needed to satisfy lxc dependencies.
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17553
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The patch adding temperature sensor support for r8169 has been removed upstream
and the functionality will be added to Realtek PHY instead:
1f691a1fc4
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This was the first DSA packaged, and the tagger was made into
a separate package. This is too complicated: the mv88e6xxx
is the only module using this tagger after all, fold the module
for the DSA hardware and the driver for the tagger into a
single package and let modprobe do its job of probing the
tagger for the driver.
Tested on the BMIPS Inteno XG6846.
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250110-mv88e6xxx-single-package-v1-1-223ad7fb312e@linaro.org/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This LED controller has a driver under development which is currently being reviewed by the respective kernel maintainers. They are currently on v11 which is included here.
The LED1202 is a 12-channel low quiescent current LED driver with:
* Supply range from 2.6 V to 5 V
* 20 mA current capability per channel
* 1.8 V compatible I2C control interface
* 8-bit analog dimming individual control
* 12-bit local PWM resolution
* 8 programmable patterns
If the led node is present in the controller then the channel is
set to active.
The output current can be adjusted separately for each channel by 8-bit
analog (current sink input) and 12-bit digital (PWM) dimming control. The
LED1202 implements 12 low-side current generators with independent dimming
control.
Internal volatile memory allows the user to store up to 8 different patterns,
each pattern is a particular output configuration in terms of PWM
duty-cycle (on 4096 steps). Analog dimming (on 256 steps) is per channel but
common to all patterns. Each device tree LED node will have a corresponding
entry in /sys/class/leds with the label name. The brightness property
corresponds to the per channel analog dimming, while the patterns[1-8] to the
PWM dimming control.
Signed-off-by: Manuel Fombuena <fombuena@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17451
Signed-off-by: Robert Marko <robimarko@gmail.com>
7a3bcd39ae1f r8169: use helper r8169_mod_reg8_cond to simplify rtl_jumbo_config
e3e9e9039fa6 r8169: align WAKE_PHY handling with r8125/r8126 vendor drivers
330dc2297c82 r8169: improve rtl_set_d3_pll_down
c507e96b5763 r8169: improve __rtl8169_set_wol
83cb4b470c66 r8169: remove leftover locks after reverted change
2cd02f2fdd8a r8169: improve initialization of RSS registers on RTL8125/RTL8126
a3d8520e6a19 r8169: align RTL8126 EEE config with vendor driver
4af2f60bf737 r8169: align RTL8125/RTL8126 PHY config with vendor driver
eb90f876b796 r8169: align RTL8125 EEE config with vendor driver
b8bd8c44a266 r8169: fix inconsistent indenting in rtl8169_get_eth_mac_stats
f75d1fbe7809 r8169: add support for RTL8125D
c4e64095c00c r8169: enable EEE at 2.5G per default on RTL8125B
d64113c6bb5e r8169: remove rtl_dash_loop_wait_high/low
1c105bacb160 r8169: avoid duplicated messages if loading firmware fails and switch to warn level
ac48430368c1 r8169: don't take RTNL lock in rtl_task()
e3fc5139bd8f r8169: implement additional ethtool stats ops
b8bf38440ba9 r8169: enable SG/TSO on selected chip versions per default
854d71c555df r8169: remove original workaround for RTL8125 broken rx issue
1ffcc8d41306 r8169: add support for the temperature sensor being available from RTL8125B
The following patches require backporting additional linux patches:
e2015942e90a r8169: replace custom flag with disable_work() et al
e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Just one of the devices uses the Marvell MV88E6060 DSA
switch so break this out from the generic kernel config
and into a package selected only by that single device
and probed at boot instead.
The big win is from being able to drop the dsa_core
(~600KB) kernel module out of the common kernel on
devices with no DSA switch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix bogus reference to kmod-nf-conntrack-timeout, fixing the warning
`WARNING: Makefile 'package/kernel/linux/Makefile' has a dependency on
'kmod-nf-conntrack-timeout', which does not exist`.
Fixes: 0e2dcfc4f488 ("netfilter: add kmod-nfnetlink-ct{helper,timeout}")
Signed-off-by: Joel Low <joel@joelsplace.sg>
Link: https://github.com/openwrt/openwrt/pull/17388
Signed-off-by: Robert Marko <robimarko@gmail.com>
Package bnxt_en kernel module for Broadcom NetXtreme-C/E based Ethernet
network chips like BCM573xx and BCM574xx.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17301
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit 1cea889c96a8df4e91236e269539b086d519a60a.
This reverts commit 5fd86d66c15fc4d6f5076f7d07c91e0690d91531.
The patch is causing build servers to fail. Revert it for now.
Signed-off-by: John Crispin <john@phrozen.org>
This option enables support for monochrome LEDs that are grouped into multicolor
LEDs which is useful in the case where LEDs of different colors are physically
grouped in a single multi-color LED and driven by a controller that doesn't have
multi-color support.
Signed-off-by: Jonathan Brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/16397
Signed-off-by: John Crispin <john@phrozen.org>
This commit adds the Linux kernel mainline driver "leds-ktd202x" for the
KinetIC KTD2026 and KTD2027 RGB/RBGW controller with I2C interface that was
introduced in kernel version 6.7, last changed in mainline on 2024-05-31.
At least the Acer Connect Vero W6m (a variant of the Acer Predator Connect
W6 without 2.5G eth1 port, usb3 port, and the 6 on-board gpio RGB LEDs) is
equipped with a KTD2026 (and a single RGB LED attached to it used by the
stock firmware as status LED), and maybe other router devices also are.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16860
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Change the dependency on the kmod-media-controller from depends to
select.
Fixes: 109592524663 ("kernel: add kmod-media-controller dependency for kmod-usb-audio")
Link: https://github.com/openwrt/openwrt/pull/17058
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Netatalk v4 reintroduces AppleTalk and this module is required for
layer 3 protocol support.
Module was removed in kernel 4.14 for OpenWrt 18.06 (commmit
14a0131, 22/02/2018). At the time nothing used it as Netatalk v3
did not support AppleTalk.
Not building ipddp feature/module like it was in the past, as
recommended by upstream Netatalk maintainers.
Signed-off-by: Antonio Pastor <antonio.pastor@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16979
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These packages are needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The snd-usb-audio drivers uses media controller if media controller is set.
So add kmod-media-controller as dependency.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Disable drm-i915 module for target x86/geode.
Fixes: 77cfe8f ("x86: make i915 as a kmod with required firmware")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16977
Signed-off-by: Robert Marko <robimarko@gmail.com>
i915 driver requires to load correct firmware to work on latest x86
GPU, it is more reasonable to make it as a kernel module, so that
initramfs is not required, and it can also save some space from the
kernel image comparing being a built-in driver
Signed-off-by: Joe Zheng <joe.zheng@intel.com>
Link: https://github.com/openwrt/openwrt/pull/16276
Signed-off-by: Robert Marko <robimarko@gmail.com>
Package kmod-drm-panel-mipi-dbi as well as modules it depends on in
order to support a wide range of MIPI DBI complaint SPI-connected
TFT panels.
See https://github.com/notro/panel-mipi-dbi/ for more information on
how to use specific panels.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Package gs_usb CAN driver, which is for Geschwister Schneider and
bytewerk.org candleLight compatible USB/CAN interfaces.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Drop limitation on depending on only armv8 for armsr target as those
module should support both 32 and 64 bits systems.
Only thunderx-net actually require 64 bit systems.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add INET diag socket monitoring interface module for MultiPath TCP.
It allows using native Linux socket diagnostic tools such as 'ss' for
Multipath TCP connections.
Co-authored-by: Rodrigo B. de Sousa Martins <rodrigo.sousa.577@gmail.com>
Signed-off-by: sKy King <29267720+sKyissKy@users.noreply.github.com>
Link: https://github.com/openwrt/openwrt/pull/12884
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Set the boot flag for the igc, mlx4-core, and mlx5-core network device drivers
to load them at a more early stage of the boot process.
This is required for network drivers whose network interface PCI paths are set
via ucidef_set_network_device_path inside the 02_network script since it is
called after kernel modules are loaded from modules-boot.d but before they are
loaded from the modules.d directory.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/16560
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The swconfig-based b53 driver for the BCM53128 switch stopped working
after commits b2cfed48f6 (Revert "swconfig: fix Broadcom b53 support")
and e4e410733f (kernel: export switch_generic_set_link() symbol). This
rendered the 8 LAN ports of the EdgeSwitch 8XP non-functional, so the
image compilation for the device was disabled (5a1d7d8c1b).
This commit adds the kmod-dsa-b53-mdio and kmod-dsa-b53 packages
with the upstream B53 DSA driver, replacing the swconfig-based
kmod and kmod-switch-bcm53xx-mdio downstream ones that are not used by
any other device.
The 8 LAN ports of the EdgeSwitch 8XP are usable again. The 02_network
init script has been updated with the new DSA interfaces lan1 .. lan8.
Image building has been reenabled for the device, adding the usual DSA
incompatibility notice.
Tested on a Ubiquiti EdgeSwitch 8XP.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Link: https://github.com/openwrt/openwrt/pull/11680
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This solution that is needed for some routers to provide proper
LED activity when controlled directly by the MV88E6xxx switch,
has just been merged in upstream Linux.
Make this patch 901 as other backports from earlier kernels
are in patch 896 and this is the first free number after
that.
Patch offsets in pending patches are augmented as part of
the refresh.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
RmNet driver provides a transport agnostic MAP (multiplexing and
aggregation protocol) support in embedded module. Module provides
virtual network devices which can be attached to any IP-mode
physical device.
This is commonly used on Qualcomm based modems for data aggregation.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
1. Remove outdated symbol CONFIG_USB_OHCI_ATH79.
The ath79 OHCI USB was already supported by the generic driver
kmod-usb-ohci. And this kernel symbol has been dropped since
upstream commit:
53d473fc1e38 ("usb: host: Remove the deprecated ATH79 USB host config options")
2. Add ath79 USB phy package to the OHCI dependencies.
Both EHCI and OHCI require it on the ath79 target.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16380
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Compile LED support to swconfig and phy modules
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for building DSA switch drivers as kernel modules.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for building multiple phy drivers as kernel modules
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for building both upstream and downstream ag71xx drivers
as modules.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* Adds the x86_64 dependency for mlxsw_core
* Removes the redundant mlxsw_core dependency
from mlxsw-minimal and mlxsw-spectrum
* Removes the DCB configuration symbols because
they were moved into the generic configuration
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/15362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds the missing x86 dependency for
the Mellanox mlxcpld LED driver.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/15362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
