The Zyxel EMG2926-Q10A is 99% the Zyxel NBG6716, but the bootloader
expects a different product name when flashing over TFTP. Also, the
EMG2926-Q10A always has 128 MiB of NAND flash whereas the NBG6716
reportedly can have either 128 MiB or 256 MiB.
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Netgear R6100 is a dual-band Wi-Fi 5 (AC1200) router based on Qualcomm
Atheros (AR9344 + QCA9882) platform. Support for this device was first
introduced in 15f6f67d18 (ar71xx). FCC ID: PY312400225.
Specifications:
- Atheros AR9344 (560 MHz)
- 128 MB of RAM (DDR2)
- 128 MB of flash (parallel NAND)
- 2T2R 2.4 GHz Wi-Fi (AR9344)
- 2T2R 5 GHz Wi-Fi (QCA9882)
- 5x 10/100 Mbps Ethernet (AR9344)
- 4x internal antenna
- 1x USB 2.0 (GPIO-controlled power)
- 6x LED, 3x button (reset, Wi-Fi, WPS)
- UART (4-pin, 2.54 mm pitch) header on PCB
- 1x mechanical power switch
- DC jack for main power input (12 V)
WARNING: sysupgrade from older stable releases is not possible, fresh
installation (via vendor's GUI or TFTP based recovery) is required.
Reason for that is increased kernel partition size.
Installation:
Use the 'factory' image under vendor's GUI or via TFTP U-Boot recovery.
You can use the 'nmrpflash' tool at a boot time, before kernel is loaded
or start it manually by pressing the 'reset' button for ~20 seconds from
powering up the device (U-Boot will start TFTP server on 192.168.1.1,
use TFTP client to send the image).
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Dongwon T&I DW02-412H is a 2.4/5GHz band 11ac (WiFi-5) router, based on
Qualcomm Atheros QCA9557.
Specifications
--------------
- SoC: Qualcomm Atheros QCA9557-AT4A
- RAM: DDR2 128MB
- Flash: SPI NOR 2MB (Winbond W25Q16DVSSIG / ESMT F25L16PA(2S)) +
NAND 64/128MB
- WiFi:
- 2.4GHz: QCA9557 WMAC
- 5GHz: QCA9882-BR4A
- Ethernet: 5x 10/100/1000Mbps
- Switch: QCA8337N-AL3C
- USB: 1x USB 2.0
- UART:
- JP2: 3.3V, TX, RX, GND (3.3V is the square pad) / 115200 8N1
Installation
--------------
1. Connect a serial interface to UART header and
interrupt the autostart of kernel.
2. Transfer the factory image via TFTP and write it to the NAND flash.
3. Update U-Boot environment variable.
> tftpboot 0x81000000 <your image>-factory.img
> nand erase 0x1000000
> nand write 0x81000000 0x1000000 ${filesize}
> setenv bootpart 2
> saveenv
Revert to stock firmware
--------------
1. Revert to stock U-Boot environment variable.
> setenv bootpart 1
> saveenv
MAC addresses as verified by OEM firmware
--------------
WAN: *:XX (label)
LAN: *:XX + 1
2.4G: *:XX + 3
5G: *:XX + 4
The label MAC address was found in art 0x0.
Credits
--------------
Credit goes to the @manatails who first developed how to port OpenWRT
to this device and had a significant impact on this patch.
And thanks to @adschm and @mans0n for guiding me to revise the code
in many ways.
Signed-off-by: Jihoon Han <rapid_renard@renard.ga>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Sungbo Eo <mans0n@gorani.run>
Many people appear to use an unneeded "+" prefix for the increment
when calculating a MAC address with macaddr_add. Since this is not
required and used inconsistently [*], just remove it.
[*] As a funny side-fact, copy-pasting has led to almost all
hotplug.d files using the "+", while nearly all of the
02_network files are not using it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the WNDR4300TN, marketed by Belgian ISP
Telenet. The hardware is the same as the WNDR4300 v1, without the
fifth ethernet port (WAN) and the USB port. The circuit board has
the traces, but the components are missing.
Specifications:
* SoC: Atheros AR9344
* RAM: 128 MB
* Flash: 128 MB NAND flash
* WiFi: Atheros AR9580 (5 GHz) and AR9344 (2.4 GHz)
* Ethernet: 4x 1000Base-T
* LED: Power, LAN, WiFi 2.4GHz, WiFi 5GHz, WPS
* UART: on board, to the right of the RF shield at the top of the board
Installation:
* Flashing through the OEM web interface:
+ Connect your computer to the router with an ethernet cable and browse
to http://192.168.0.51/
+ Log in with the default credentials are admin:password
+ Browse to Advanced > Administration > Firmware Upgrade in the Telenet
interface
+ Upload the Openwrt firmware: openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img
+ Proceed with the firmware installation and give the device a few
minutes to finish and reboot.
* Flashing through TFTP:
+ Configure your wired client with a static IP in the 192.168.1.x range,
e.g. 192.168.1.10 and netmask 255.255.255.0.
+ Power off the router.
+ Press and hold the RESET button (the factory reset button on the bottom
of the device, with the gray circle around it, next to the Telenet logo)
and turn the router on while keeping the button pressed.
+ The power LED will start flashing orange. You can release the button
once it switches to flashing green.
+ Transfer the image over TFTP:
$ tftp 192.168.1.1 -m binary -c put openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img
Signed-off-by: Davy Hollevoet <github@natox.be>
[use DT label reference for adding LEDs in DTSI files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The gl-e750 is a portable travel router that gives you safe access to
the internet while traveling.
Specifications:
- SoC: Qualcomm Atheros AR9531 (650MHz)
- RAM: 128 MB DDR2
- Flash: 16 MB SPI NOR (W25Q128FVSG) + 128 MB SPI NAND (GD5F1GQ4UFYIG)
- Ethernet: 10/100: 1xLAN
- Wireless: QCA9531 2.4GHz (bgn) + QCA9887 5GHz (ac)
- USB: 1x USB 2.0 port
- Switch: 1x switch
- Button: 1x reset button
- OLED Screen: 128*64 px
MAC addresses based on vendor firmware:
LAN *:a0 art 0x0
2.4GHz *:a1 art 0x1002
5GHz *:a2 art calculated from art 0x0 + 2
Flash firmware:
Since openwrt's kernel already exceeds 2MB, upgrading from the official
version of GL-inet (v3.100) using the sysupgrade command will break the
kernel image. Users who are using version 3.100 can only upgrade via
uboot. The official guidance for GL-inet is as follows:
https://docs.gl-inet.com/en/3/troubleshooting/debrick/
In the future, GL-inet will modify the firmware to support the sysupgrade
command, so users will be able to upgrade directly with the sysupgrade
command in future releases.
OLED screen control:
OLED controller is connected to QCA9531 through serial port, and can send
instructions to OLED controller directly through serial port.
Refer to the links below for a list of supported instructions:
https://github.com/gl-inet/GL-E750-MCU-instruction
Signed-off-by: Luochongjun <luochongjun@gl-inet.com>
[fix alphabetic sorting in 10-fix-wifi-mac, drop check-kernel-size]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the WNDR4300SW, marketed by California ISP
SureWest (hence the 'SW' suffix). Hardware wise, it's identical to the
WNDR4300 v1.
Specifications:
* SoC: Atheros AR9344
* RAM: 128 MB
* Flash: 128 MB NAND flash
* WiFi: Atheros AR9580 (5 GHz) and AR9344 (2,4 GHz)
* Ethernet: 5x 1000Base-T
* LED: Power, WAN, LAN, WiFi, USB, WPS
* UART: on board, to the right of the RF shield at the top of the board
Installation:
* Flashing through the OEM web interface:
+ Connect your computer to the router with an ethernet cable and browse
to http://192.168.1.1/
+ Log in with the default credentials are admin:password
+ Browse to Advanced > Administration > Firmware Upgrade in the Netgear
interface
+ Upload the Openwrt firmware: openwrt-ath79-nand-netgear_wndr4300sw-squashfs-factory.img
+ Proceed with the firmware installation and give the device a few
minutes to finish and reboot.
* Flashing through TFTP:
+ Configure your wired client with a static IP in the 192.168.1.x range,
e.g. 192.168.1.10 and netmask 255.255.255.0.
+ Power off the router.
+ Press and hold the RESET button (the factory reset button on the bottom
of the device, with the red circle around it) and turn the router on
while keeping the button pressed.
+ The power LED will start flashing orange. You can release the button
once it switches to flashing green.
+ Transfer the image over TFTP:
$ tftp 192.168.1.1 -m binary -c put openwrt-ath79-nand-netgear_wndr4300sw-squashfs-factory.img
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2.4 GHz Wifi on ath79 is set up in 10-ath9k-eeprom, but in ar71xx
it was done with ath79_register_wmac.
Thus, the following errors are observed on the device:
ath: phy1: Unable to initialize hardware; initialization status: -5
ath9k 18100000.wmac: failed to initialize device
ath9k: probe of 18100000.wmac failed with error -5
This patch changes the ath79 support to properly use wmac as well.
This will also require fixing the MAC address in a different way.
Signed-off-by: Guillaume Lefebvre <guillaume@zelig.ch>
[several adjustments to 10-fix-wifi-mac, use correct MAC address,
rewrite commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit creates the ath79/mikrotik subtarget in order to support
MikroTik devices based on Qualcomm Atheros MIPS SoCs.
MikroTik devices need a couple of specific features: the split MiNOR
firmware MTD format, which is not used by other devices, and the 4k
sector erase size on SPI NOR storage, which can not be added to the
ath79/generic and ath79/nand subtargets now.
Additionally, the commit moves the two MikroTik devices already in
the generic and nand subtargets to this new one.
Tested on the RB922 board and the wAP AC router.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This commit ports the device from ar71xx to the ath79 target and
modifies the partition layout.
1. Firmware is installed to nand flash.
2. Modify the uboot-env parameter to boot from the nand flash.
3. The kernel size is extended to 5M.
4.nor flash retains the oem firmware.
oem partition layout
dev: size erasesize name
mtd0: 00040000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00e30000 00010000 "rootfs"
mtd3: 00170000 00010000 "kernel"
mtd4: 00010000 00010000 "art"
mtd5: 00f90000 00010000 "firmware"
mtd6: 06000000 00020000 "rootfs_data"
mtd7: 02000000 00020000 "backup"
new partition layout
dev: size erasesize name
mtd0: 00040000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00fa0000 00010000 "oem-firmware"
mtd3: 00010000 00010000 "art"
mtd4: 00500000 00020000 "kernel"
mtd5: 05b00000 00020000 "ubi"
mtd6: 02000000 00020000 "oem-backup"
MAC address overview:
All mac addresses are stored in the art partition.
eth0: 0x0
eth1: 0x6
ath9k: 0xc
ath10k: 0x12
No valid addresses in 0x1002 and 0x5006. All addresses match the OEM
firmware.
Install from oem firmware.
Enable ssh service:
Connect to the router web, click professional, click system-startup,
and add dropbear in the local startup input box. Click
system-administration, delete ssh-key, and replace your ssh pub key.
Restart the router.
1.Upload openwrt firmware to the device
scp openwrt-snapshot-r11365-df60a0852c-ath79-nand-domywifi_dw33d-\
squashfs-factory.bin root@192.168.10.1:/tmp
2.modify uboot-env.
ssh login to the device:
fw_setenv bootcmd 'nboot 0x8050000 0;bootm || bootm 0x9fe80000'
Run the fw_printenv command to check if the settings are correct.
3.Write openwrt firmware.
ssh login to the device:
mtd -r write /tmp/openwrt-snapshot-r11365-df60a0852c-ath79-nand-\
domywifi_dw33d-squashfs-factory.bin /dev/mtd6
The device will restart automatically and the openwrt firmware
installation is complete.
Restore oem firmware.just erase the kernel partition and the ubi
partition.
ssh login to the device:
mtd erase /dev/mtd4
mtd -r erase /dev/mtd5
Reboot the device
Signed-off-by: WeiDong Jia <jwdsccd@gmail.com>
[alter flash instruction in commit message]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This patch ports support for the MikroTik RouterBOARD 922UAGS-5HPacD
with a built-in 802.11ac High-Power radio (31dBm), which was already
available in the ar71xx target.
See https://mikrotik.com/product/RB922UAGS-5HPacD for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9558 (720 MHz)
- RAM: 128 MB
- Storage: 128 MB NAND
- Wireless: external QCA9882 802.11a/ac 2x2:2
- Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE-in 24V
- SFP: 1x host
- USB: 1x 2.0 type A
- PCIe: 1x Mini slot (also contains USB 2.0 for 3G/LTE modems)
- SIM slot: 1x mini-SIM
Working:
- Board/system detection
- SPI and NAND storage
- PCIe
- USB type A host
- Wireless
- Ethernet
- LEDs (user, phy0)
- Reset button
- Sysupgrade to/from ar71xx
Not supported:
- RSSI LEDs
- SFP cage
Installation methods:
- Sysupgrade from ar71xx (it is advisable to use the -n option to
wipe any previous settings), or
- Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This patch introduces support for Netgear WNDR4500v3. Router
is very similar to WNDR4300v2 and is based on the same PCB.
Information gathered from various Internet sources (including
https://patchwork.ozlabs.org/patch/809227/) shows following
differences to WNDR4300v2:
* two USB 2.0 ports with separate LEDs
* USB LEDs soldered to secondary pads
* WPS and RFKILL buttons soldered to secondary pads
* described as N900 device with 3x3:3 MIMO for 2.4GHz radio
* power supply requirement is DC 12V 2.5A
* vendor HW ID suffix differs in one digit
* bigger chassis
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This patch introduces support for Netgear WNDR4300v2.
Specification
=============
* Description: Netgear WNDR4300 v2
* Loader: U-boot
* SOC: Qualcomm Atheros QCA9563 (775 MHz)
* RAM: 128 MiB
* Flash: 2 MiB SPI-NOR + 128 MiB SPI-NAND
- NOR: U-boot binary: 256 KiB
- NOR: U-boot environment: 64 KiB
- NOR: ART Backup: 64 KiB
- NOR: Config: 64 KiB
- NOR: Traffic Meter: 64 KiB
- NOR: POT: 64 KiB
- NOR: Reserved: 1408 KiB
- NOR: ART: 64 KiB
- NAND: Firmware: 25600 KiB (see notes for OpenWrt)
- NAND: Language: 2048 KiB
- NAND: mtdoops Crash Dump: 128 KiB
- NAND: Reserved: 103296 KiB
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8337)
* Wireless:
- 2.4 GHz b/g/n (internal)
- 5 GHz a/n (AR9580)
* USB: yes, 1 x USB 2.0
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN 2G (green)
- WLAN 5G (blue)
- 4 x LAN (amber/green)
- USB (green)
- WPS (green)
* UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 1.5A
* MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2
Important Notes
===============
0. NOR Flash (2 MiB) is not touched by OpenWrt installation.
1. NAND Flash (128 MiB) layout under OpenWrt is changed as follows:
all space is split between 4 MiB kernel and 124 MiB UBI areas;
vendor partitions (language and mtdoops) are removed; kernel space
size can be further expanded if needed; maximum image size is set
to 25600k for compatibility reasons and can also be increased.
2. CPU clock is 775 MHz, not 750 MHz.
3. 5 GHz wireless radio chip is Atheros AR9580-AR1A with bogus PCI
device ID 0xabcd. For ath9k driver to load successfully, this is
overriden in DTS with correct value for this chip, 0x0033.
4. RFKILL button is wired to AR9580 pin 9 which is normally disabled
by chip definition in ath9k code (0x0000F4FF gpio mask). Therefore
'qca,gpio-mask=<0xf6ff>' hack must be used for button to work
properly.
5. USB port is always on, no GPIO for 5V power control has been
identified.
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_nand=y
CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300-v2=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
The GL.iNet GL-AR750S has been supported by the ar71xx and ath79
platforms with access to its 16 MB NOR flash, but not its 128 MB
SPI NAND flash.
This commit provides support for the NAND through the upstream
SPI-NAND framework.
At this time, the OEM U-Boot appears to only support loading the
kernel from NOR. This configuration is preserved as this time,
with the glinet,gl-ar750s-nand name reserved for a potential,
future, NAND-only boot.
The family of GL-AR750S devices on the ath79 platform now includes:
* glinet,gl-ar750m-nor-nand "nand" target
* glinet,gl-ar750m-nor "nand" target (NAND-aware)
NB: This commit increases the kernel size from 2 MB to 4 MB
"Force-less" sysupgrade is presently supported from the current
versions of following NOR-based firmwre images to the version of
glinet,gl-ar750s-nor firmware produced by this commit:
* glinet,gl-ar750s -- OpenWrt 19.07 ar71xx
* glinet,gl-ar750s -- OpenWrt 19.07 ath79
Users who have sucessfully upgraded to glinet,gl-ar750m-nor may then
flash glinet,gl-ar750m-nor-nand with sysupgrade to transtion to the
NAND-based variant.
Other upgrades to these images, including directly to the NAND-based
glinet,gl-ar750s-nor-nand firmware, can be accomplished through U-Boot.
NB: See "ath79: restrict GL-AR750S kernel build-size to 2 MB" which
enables flashing of NAND factory.img with the current GL-iNet U-Boot,
"U-Boot 1.1.4-gcf378d80-dirty (Aug 16 2018 - 07:51:15)"
The GL-AR750S OEM U-Boot allows upload and flashing of either NOR
firmware (sysupgrade.bin) or NAND firmware (factory.img) through its
HTTP-based GUI. Serial connectivity is not required.
The glinet,gl-ar750s-nor and glinet,gl-ar750s-nor-nand images
generated after this commit flash each other directly.
This commit changes the control of the USB VBUS to gpio-hog from
regulator-fixed introduced by commit 0f6b944c92. This reduces the
compressed kernel size by ~14 kB, with no apparent loss of
functionality. No other ath79-nand boards are using regulator-fixed
at this time.
Note: mtd_get_mac_binary art 0x5006 does not return the proper MAC
and the GL.iNet source indicates that only the 0x0 offset is valid
The ar71xx targets are unmodified.
Cc: Alexander Wördekemper <alexwoerde@web.de>
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
This fixes several issues introduced with ZyXEL NBG6716 support:
- Inhomogeneous indent
- Wrong ath10k MAC patching function
- Wrong brackets for pad-to in nand.mk
- Add missing DEVICE_MODEL
- Remove k2t.sh include (copy/paste leftover)
Fixes: 99835e0999 ("ath79: add support for ZyXEL NBG6716")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Due to rebase of the base-files split patch after adding support
for the ZyXEL NBG6716, its base-files were added to the generic
subtarget, although the device belongs to the nand subtarget.
This moves the definitions to their proper locations.
Fixes: 0130022bae ("ath79: split base-files into subtargets")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[improve commit message, rebase]
Signed-off-by: David Bauer <mail@david-bauer.net>