Manually rebased: ath79/patches-5.10/910-unaligned_access_hacks.patch
All other patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit acb10faa35)
Some copper SFP modules come with Marvell's 88E1xxx PHY and need this
module to function. Package it, so users can easily install this PHY
driver and use e.g. FINISAR CORP. FCLF-8521-3-HC SFP.
Without marvell PHY driver:
sfp sfp2: module FINISAR CORP. FCLF-8521-3-HC rev A sn XXXXXXX dc XXXXXX
mt7530 mdio-bus:1f sfp2: validation with support 0000000,00000000,00000000 failed: -22
sfp sfp2: sfp_add_phy failed: -22
With marvell PHY driver:
sfp sfp2: module FINISAR CORP. FCLF-8521-3-HC rev A sn XXXXXXX dc XXXXXX
mt7530 mdio-bus:1f sfp2: switched to inband/sgmii link mode
mt7530 mdio-bus:1f sfp2: PHY [i2c:sfp2:16] driver [Marvell 88E1111] (irq=POLL)
mt7530 mdio-bus:1f sfp2: Link is Up - 1Gbps/Full - flow control rx/tx
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit ebe2b7190b)
As reported by @kuanyili on Github, commit 3564c22e46 broke CI build:
3564c22e46 (commitcomment-91091149)
Adding back those symbols fixes the problem.
Fixes: 3564c22e46 ("bcm27xx: disable duplicate sdhost driver")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Enabling both CONFIG_MMC_BCM2835 and CONFIG_MMC_BCM2835_SDHOST causes this
error in dmesg:
Error: Driver 'sdhost-bcm2835' is already registered, aborting...
Disabling CONFIG_MMC_BCM2835 and leaving CONFIG_MMC_BCM2835_SDHOST enabled
avoids this error.
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B
Signed-off-by: John Audia <therealgraysky@proton.me>
[Disable driver for all subtargets, refresh configs, tweak description]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 3f7cc9d014)
OpenWrt's support for splitting rootfs (to create an extra "rootfs_data"
partition) is limited to partitions called "rootfs". Upstream kernel
allows any name partition to be rootfs if it has "linux,rootfs" property
set. Add split support to such partitions in OpenWrt code.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit e4770db163)
This helps choosing the right NTFS driver from two available options.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit b066ad7d9a)
This DT property allows marking flash partition that Linux should use as
a root device. It's useful for devices that don't use U-Boot and cmdline
parser for partitioning. It may be used with "fixed-partitions" or some
dynamic partitioning based on flash content.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit d33e49857e)
This is some hack on top of our old hack. Use separated patch for it so
it's easier to understand and actually possible to describe. We should
ideally get rid of this (and we actually did with kernels 5.15+).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 6a64eb2664)
Add UIMAGE_NAME and UIMAGE_MAGIC to allow users to directly install
initramfs-kernel.bin from the stock firmware Web UI. At the same time,
this change makes it possible to boot OpenWrt with the official u-boot.
Notice:
Since the stock firmware is based on OpenWrt and the configuration
will be retained by default during the upgrade process, so we must use
initramfs-kernel.bin to do a initial installation. After the system
restarts, install sysupgrade.bin and do not retain any configuration.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit eba0a8deb6)
The SPI max frequency was set to 80MHz, considerably higher than the
vendor clocks it in their firmware (10MHz). Multiple users reported
jffs2 corruption/instability in GitHub issue #10461.
My unit has a W25Q256; datasheet specifies maximum SPI frequency for
read command of 50MHz.
Thanks to @DragonBlueP for suggesting to eliminate m25p,fast-read;
and @MPannen1979 for identifying the problem.
Fixes: #10461
Signed-off-by: Michael Lyle <mlyle@lyle.org>
(cherry picked from commit 961e01fc67)
Fix the LZMA ERROR 1 with a single line of recipe instead of duplicating
"uimage-lzma-loader".
While reviewing my original submission of commit ce19571004 David
suggested to use $(Device/uimage-lzma-loader), but due to the specific
needs of the vendor bootloader that simple oneliner didn't work.
The new $(Device/seama-lzma-loader) is for those SEAMA capable
bootloaders.
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
(cherry picked from commit 18801f2648)
In the support topic [0] of the GitHub issue #10634 it was found out
(based on boot logs) that the uimage-lzma-loader (commit 09faa73c53)
never worked, as an earlier workaround (commit 6fba88de19) negated
the recipe:
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
.raspi_read: from:50000 len:c
.raspi_read: from:50000 len:1fa000
................................We have SEAMA, Image Size = 2072512
Verifying Checksum ...
Uncompressing SEAMA linux.lzma ... OK
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 5.4.188 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16554-1d4dea6d4f)) #0 Sat Apr 16 12:59:34 2022
[ 0.000000] SoC Type: Ralink RT3883 ver:1 eco:5
[ 0.000000] printk: bootconsolde [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] MIPS: machine is D-Link DIR-645
[ 0.000000] Initrd not found or empty - disabling initrd
Using the new seama-lzma-loader it's able to boot OpenWrt 22.03
and OpenWrt SNAPSHOT too:
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
.raspi_read: from:50000 len:c
.raspi_read: from:50000 len:48b004
.........................................................................We have SEAMA, Image Size = 4763588
Verifying Checksum ...
Uncompressing SEAMA linux.lzma ... OK
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
OpenWrt kernel loader for MIPS based SoC
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Decompressing kernel... done!
Starting kernel at 80000000...
[ 0.000000] Linux version 5.10.144 (xabolcs@ut2004) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r20774+2-b71affaf8b) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 Tue Sep 27 23:02:30 2022
[ 0.000000] SoC Type: Ralink RT3883 ver:1 eco:5
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] MIPS: machine is D-Link DIR-645
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
The OKLI Loader is unable to read the flash on this SoC:
Looking for OpenWrt image... not found! ('0xddbaddba' at 0xbc051000)
0: https://forum.openwrt.org/t/136435
Fixes: GitHub issue #10634 ("V22.03.0 release currently does not work on D-Link DIR-645")
Fixes: 09faa73c53 ("ramips: rt3883: use lzma-loader for DIR-645")
Tested-by: Glenn Fowler <gfowler1@outlook.com>
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
(cherry picked from commit c293b492df)
Define "Device/seama-lzma-loader" recipe for SEAMA devices to help
contributors avoid doing recipe mistakes.
In a forum topic [0] I was under the impression that the good old
uimage-lzma-loader didn't fix the LZMA ERROR 1 for a device.
It was found out, that the uimage-lzma-loader never worked because the
KERNEL variable was overriden earlier (also an LZMA ERROR 1 related
commit, 6fba88de19), and the "use lzma-loader" fix (commit
09faa73c53) didn't catch that to include the "loader-kernel" part.
I contributed an LZMA ERROR 1 fix (commit ce19571004) for the SEAMA
device D-Link DIR-860L B1, where I had to duplicate the whole
uimage-lzma-loader recipe because of the special needs of the vendor
bootloader.
This new recipe reuse most of uimage-lzma-loader's KERNEL definiton to
avoid duplication.
It uses "relocate-kernel" as it needed for D-Link DIR-860L B1 to
boot from flash, and it's compatible with D-Link DIR-645 too.
It repacks lzma-loader with lzma for kernel (without uImage), because
these weird hacked vendor bootloaders accepts only LZMA compressed
kernels from flash:
We have SEAMA, Image Size = 4759794
Verifying Checksum ...
Uncompressing SEAMA linux.lzma ... OK
It uses uImage header for initramfs kernel to be little bit verbose.
0: https://forum.openwrt.org/t/136435/10
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
(cherry picked from commit e7ad68d682)
On TP-Link ar7241 devices LAN and WAN interfaces are swapped. Keeping
that in mind fix MAC address assignment as used in vendor firmware:
LAN MAC - main MAC stored in u-boot and printed on label
WAN MAC - LAN MAC + 1
Signed-off-by: Will Moss <willormos@gmail.com>
(cherry picked from commit 5a1af6ed62)
Add support for the Linksys EA4500 v3 wireless router
Hardware
--------
SoC: Qualcomm Atheros QCA9558
RAM: 128M DDR2 (Winbond W971GG6KB-25)
FLASH: 128M SPI-NAND (Spansion S34ML01G100TFI00)
WLAN: QCA9558 3T3R 802.11 bgn
QCA9580 3T3R 802.11 an
ETH: Qualcomm Atheros QCA8337
UART: 115200 8n1, same as ea4500 v2
USB: 1 single USB 2.0 host port
BUTTON: Reset - WPS
LED: 1x system-LED
LEDs besides the ethernet ports are controlled
by the ethernet switch
MAC Address:
use address(sample 1) source
label 94:10:3e:xx:xx:6f caldata@cal_macaddr
lan 94:10:3e:xx:xx:6f $label
wan 94:10:3e:xx:xx:6f $label
WiFi4_2G 94:10:3e:xx:xx:70 caldata@cal_ath9k_soc
WiFi4_5G 94:10:3e:xx:xx:71 caldata@cal_ath9k_pci
Installation from Serial Console
------------
1. Connect to the serial console. Power up the device and interrupt
autoboot when prompted
2. Connect a TFTP server reachable at 192.168.1.0/24
(e.g. 192.168.1.66) to the ethernet port. Serve the OpenWrt
initramfs image as "openwrt.bin"
3. To test OpenWrt only, go to step 4 and never execute step 5;
To install, auto_recovery should be disabled first, and boot_part
should be set to 1 if its current value is not.
ath> setenv auto_recovery no
ath> setenv boot_part 1
ath> saveenv
4. Boot the initramfs image using U-Boot
ath> setenv serverip 192.168.1.66
ath> tftpboot 0x84000000 openwrt.bin
ath> bootm
5. Copy the OpenWrt sysupgrade image to the device using scp and
install it like a normal upgrade (with no need to keeping config
since no config from "previous OpenWRT installation" could be kept
at all)
# sysupgrade -n /path/to/openwrt/sysupgrade.bin
Note: Like many other routers produced by Linksys, it has a dual
firmware flash layout, but because I do not know how to handle
it, I decide to disable it for more usable space. (That is why
the "auto_recovery" above should be disabled before installing
OpenWRT.) If someone is interested in generating factory
firmware image capable to flash from stock firmware, as well as
restoring the dual firmware layout, commented-out layout for the
original secondary partitions left in the device tree may be a
useful hint.
Installation from Web Interface
------------
1. Login to the router via its web interface (default password: admin)
2. Find the firmware update interface under "Connectivity/Basic"
3. Choose the OpenWrt factory image and click "Start"
4. If the router still boots into the stock firmware, it means that
the OpenWrt factory image has been installed to the secondary
partitions and failed to boot (since OpenWrt on EA4500 v3 does not
support dual boot yet), and the router switched back to the stock
firmware on the primary partitions. You have to install a stock
firmware (e.g. 3.1.6.172023, downloadable from
https://www.linksys.com/support-article?articleNum=148385 ) first
(to the secondary partitions) , and after that, install OpenWrt
factory image (to the primary partitions). After successful
installation of OpenWrt, auto_recovery will be automatically
disabled and router will only boot from the primary partitions.
Signed-off-by: Edward Chow <equu@openmail.cc>
(cherry picked from commit 50f727b773)
Add support for the TrendNet TEW-673GRU to ath79.
This device was supported in 19.07.9 but was deprecated with ar71xx.
This is mostly a copy of D-Link DIR-825 B1.
Updates have been completed to enable factory.bin and sysupgrade.bin both.
Code improvements to DTS file and makefile.
Architecture | MIPS
Vendor | Qualcomm Atheros
bootloader | U-Boot
System-On-Chip | AR7161 rev 2 (MIPS 24Kc V7.4)
CPU/Speed | 24Kc V7.4 680 MHz
Flash-Chip | Macronix MX25L6405D
Flash size | 8192 KiB
RAM Chip: | ProMOS V58C2256164SCI5 × 2
RAM size | 64 MiB
Wireless | 2 x Atheros AR922X 2.4GHz/5.0GHz 802.11abgn
Ethernet | RealTek RTL8366S Gigabit w/ port based vlan support
USB | Yes 2 x 2.0
Initial Flashing Process:
1) Download 22.03 tew-673gru factory bin
2) Flash 22.03 using TrendNet GUI
OpenWRT Upgrade Process
3) Download 22.03 tew-673gru sysupgrade.bin
4) Flash 22.03 using OpenWRT GUI
Signed-off-by: Korey Caro <korey.caro@gmail.com>
(cherry picked from commit 12cee86989)
There is no root-part FEATURE.
Reported-by: Karl Palsson <karlp@etactica.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit dc51342d34)
fix reading the per-packet rate on devices with firmware rate control
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 161b22d103)
dtim_period is a bss property, not a device one.
It is already handled properly in mac80211.sh
Fixes: 30c64825c7 ("hostapd: add dtim_period, local_pwr_constraint, spectrum_mgmt_required")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit ddf736e543)
This backports a commit which fixes LEDs vor the RE200 like this:
Set power LED to gpio 43 instead of 44 for v3 and v4.
Set red wifi LED to gpio 40 (was assigned to `red:wifi5g`).
Tested by the author of the initial v3 and v4 commit.
Tested-by: Richard Fröhning <misanthropos@gmx.de>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
(cherry picked from commit 02aa7a2bb9)
Needed when building with libdw and CONFIG_BUILD_NLS, mostly for the
rpath-link.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 4dc198a74e)
Improvements
- Added an interface of raising des Strausses awareness.
- Added --tips option to print strace tips, tricks, and tweaks at the end of the tracing session.
- Enhanced decoding of bpf and io_uring_register syscalls.
- Implemented decoding of COUNTER_*, RTC_PARAM_GET, and RTC_PARAM_SET ioctl commands.
- Updated lists of BPF_*, BR_*, BTRFS_*, IFA_*, IFLA_*, IORING_*, KEY_*, KVM_*, MADV_*, and UFFD_* constants.
- Updated lists of ioctl commands from Linux 5.18.
Bug fixes
- Fixed printing of the updated value of union bpf_attr.next_id on the exiting of bpf(BPF_*_GET_NEXT_ID) calls.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit 6d423ffbd1)
Improvements
- Added 64-bit LoongArch architecture support.
- Extended personality designation syntax of syscall specification expressions to support all@pers and %class@pers.
- Enhanced rejection of invalid syscall numbers in syscall specification expressions.
- Implemented decoding of set_mempolicy_home_node syscall, introduced in Linux 5.17.
- Implemented decoding of IFLA_GRO_MAX_SIZE and TCA_ACT_IN_HW_COUNT netlink attributes.
- Implemented decoding of PR_SET_VMA operation of prctl syscall.
- Implemented decoding of siginfo_t.si_pkey field.
- Implemented decoding of LIRC ioctl commands.
- Updated lists of FAN_*, IORING_*, IOSQE_*, KEY_*, KVM_*, MODULE_INIT_*, TCA_ACT_*, and *_MAGIC constants.
- Updated lists of ioctl commands from Linux 5.17.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit 36f3238dcb)
add Flow Queuing with Proportional Integral controller Enhanced (FQ-PIE) as an
optional kmod in network support and extract sched-pie from kmod-sched to
allow dependency on just kmod-sched-pie (PIE).
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
(cherry picked from commit c3e4a0d99b)
There is only one module in kmod-sched that depends on iptables. Move it
to its own kmod package so we can drop the kmod-ipt-core dependency from
kmod-sched. This makes it possible to disable all kmod-ipt-* packages
without having to disable kmod-sched. Since we now default to firewall4
and nftables, we should avoid iptables dependencies where we can.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 05775e38a5)
This extracts kmod-sched-act-police to allow using it without adding all
the packages from the big kmod-sched package.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
(cherry picked from commit 0582acf429)
This adds the act_sample.ko and psample.ko kernel module which allows
traffic sampling.
Signed-off-by: Thomas Langer <tlanger@maxlinear.com>
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
(cherry picked from commit aba1bdaed8)
Extract the kmod-sched-prio and kmod-sched-red kernel modules from the
big kmod-sched package. This allows adding the two kernel modules to
OpenWrt without adding the kmod-sched and all its depdnecy.
Signed-off-by: Thomas Langer <tlanger@maxlinear.com>
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
(cherry picked from commit 0e3911b608)
This puts the kmod-sched packages into an alphabetical order.
I kept the kmod-sched-core at the top as this is the main package.
No changes other than reordering were done.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
(cherry picked from commit c94ba95e6c)
With initial support, the mapping of LAN1/WAN and LAN2 ports was
swapped. Fix it to match labels on the device, keeping the "WAN"
personality of the first port - in line with current state of DSA setup
in master for this device.
Tested-by: Marcin Gajda <mgajda@o2.pl>
Tested-by: Christian Heuff <christian@heuff.at>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Change GPIO from 10 to 35 to make it works as expected
Fixes: 0de6a3339f ("ipq40xx: Add ZTE MF289F")
Signed-off-by: Giammarco Marzano <stich86@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit cd93980abb)
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA)
and Vodafone DE\T-Mobile PL (called GigaCube).
Modem is a MiniPCIe-to-USB based on Snapdragon X24,
it supports 4CA aggregation.
There are currently two hardware revisions, which
differ on the 5Ghz radio:
AT1 = QCA9984 5Ghz Radio on PCI-E bus
AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz
Device specification
--------------------
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz:
(QCA9984): a/n/ac, 4x4 HW REV AT1
(IPA4019): a/n/ac, 2x2 HW REV AT2
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot
Installation
------------
1. Place OpenWrt initramfs image for the device on a TFTP
in the server's root. This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial connector
GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX
(refer to this image: https://ibb.co/31Gngpr).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. Stop in u-Boot (using ESC button) and run u-Boot commands:
setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb
bootm $loadaddr
5. Please make backup of original partitions, if you think about revert to
stock, specially mtd16 (Web UI) and mtd17 (rootFS).
Use /tmp as temporary storage and do:
WEB PARITION
--------------------------------------
cat /dev/mtd16 > /tmp/mtd16.bin
scp /tmp/mtd16.bin root@YOURSERVERIP:/
rm /tmp/mtd16.bin
ROOT PARITION
--------------------------------------
cat /dev/mtd17 > /tmp/mtd17.bin
scp /tmp/mtd17.bin root@YOURSERVERIP:/
rm /tmp/mtd17.bin
6. Login via ssh or serial and remove stock partitions
(default IP 192.168.0.1):
# this can return an error, if ubi was attached before
# or rootfs part was erased before.
ubiattach -m 17
# it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs
# some devices doesn't have it
ubirmvol /dev/ubi0 -N ubi_rootfs_data
7. download and install image via sysupgrade -n
(either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin
to the device's /tmp directory)
sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin
Sometimes it could print ubi attach error, but please ignore it
if process goes forward.
Flash Layout
NAND:
mtd8: 000a0000 00020000 "fota-flag"
mtd9: 00080000 00020000 "0:ART"
mtd10: 00080000 00020000 "mac"
mtd11: 000c0000 00020000 "reserved2"
mtd12: 00400000 00020000 "cfg-param"
mtd13: 00400000 00020000 "log"
mtd14: 000a0000 00020000 "oops"
mtd15: 00500000 00020000 "reserved3"
mtd16: 00800000 00020000 "web"
mtd17: 01d00000 00020000 "rootfs"
mtd18: 01900000 00020000 "data"
mtd19: 03200000 00020000 "fota"
mtd20: 0041e000 0001f000 "kernel"
mtd21: 0101b000 0001f000 "ubi_rootfs"
SPI:
mtd0: 00040000 00010000 "0:SBL1"
mtd1: 00020000 00010000 "0:MIBIB"
mtd2: 00060000 00010000 "0:QSEE"
mtd3: 00010000 00010000 "0:CDT"
mtd4: 00010000 00010000 "0:DDRPARAMS"
mtd5: 00010000 00010000 "0:APPSBLENV"
mtd6: 000c0000 00010000 "0:APPSBL"
mtd7: 00050000 00010000 "0:reserved1"
Back to Stock (!!! need original dump taken from initramfs !!!)
-------------
1. Place mtd16.bin and mtd17.bin initramfs image
for the device on a TFTP in the server's root.
This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial console
connector (refer to the pin-out from above).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s
5. Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase RootFS+Web:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000
This will restore RootFS:
tftpboot 0x84000000 ${dir}root_uImage_s
nand erase 0x1800000 0x1D00000
nand write $fileaddr 0x1800000 $filesize
This will restore Web Interface:
tftpboot 0x84000000 ${dir}web.img
nand erase 0x1000000 0x800000
nand write $fileaddr 0x1000000 $filesize
After first boot on stock firwmare, do a factory reset.
Push reset button for 5 seconds so all parameters will
be reverted to the one printed on label on bottom of the router
Signed-off-by: Giammarco Marzano <stich86@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
(Warning: commit message did not conform to UTF-8 - hopefully fixed?,
added description of the pin-out if image goes down, reformatted
commit message to be hopefully somewhat readable on git-web,
redid some of the gpio-buttons & leds DT nodes, etc.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 0de6a3339f)
[Backported to 22.03: added DTS to the makefile patch, fixed ipq-wifi
inclusion for MF286D]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
The sector number must be stored in hex. Otherwise, the number (like 16)
will be parsed as hex and any write to the partition will end up with an
error like:
MTD erase error on /dev/mtd5: Invalid argument
Fixes: 9adfeccd84 ("uboot-envtools: Add support for IPQ806x AP148 and DB149")
Fixes: 54b275c8ed ("ipq40xx: add target")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@fungible.com>
(cherry picked from commit 8d3e932b65)
Changes between 1.1.1r and 1.1.1s [1 Nov 2022]
*) Fixed a regression introduced in 1.1.1r version not refreshing the
certificate data to be signed before signing the certificate.
[Gibeom Gwon]
Changes between 1.1.1q and 1.1.1r [11 Oct 2022]
*) Fixed the linux-mips64 Configure target which was missing the
SIXTY_FOUR_BIT bn_ops flag. This was causing heap corruption on that
platform.
[Adam Joseph]
*) Fixed a strict aliasing problem in bn_nist. Clang-14 optimisation was
causing incorrect results in some cases as a result.
[Paul Dale]
*) Fixed SSL_pending() and SSL_has_pending() with DTLS which were failing to
report correct results in some cases
[Matt Caswell]
*) Fixed a regression introduced in 1.1.1o for re-signing certificates with
different key sizes
[Todd Short]
*) Added the loongarch64 target
[Shi Pujin]
*) Fixed a DRBG seed propagation thread safety issue
[Bernd Edlinger]
*) Fixed a memory leak in tls13_generate_secret
[Bernd Edlinger]
*) Fixed reported performance degradation on aarch64. Restored the
implementation prior to commit 2621751 ("aes/asm/aesv8-armx.pl: avoid
32-bit lane assignment in CTR mode") for 64bit targets only, since it is
reportedly 2-17% slower and the silicon errata only affects 32bit targets.
The new algorithm is still used for 32 bit targets.
[Bernd Edlinger]
*) Added a missing header for memcmp that caused compilation failure on some
platforms
[Gregor Jasny]
Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit a0814f04ed)
In a254279a6c LS1012A-IOT kernel image was switched to FIT.
But u-boot config is lack of FIT and ext4 support.
This patch enables it.
It also fix envs, because for some reason this board need to use "loadaddr"
variable in brackets.
Fixes: #9894
Fixes: a254279a6c ("layerscape: Change to combined rootfs on sd images")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(cherry picked from commit d75ed3726d)
This backports a commit from upstream dnsmasq to fix CVE-2022-0934.
CVE-2022-0934 description:
A single-byte, non-arbitrary write/use-after-free flaw was found in
dnsmasq. This flaw allows an attacker who sends a crafted packet
processed by dnsmasq, potentially causing a denial of service.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 002a99eccd)
This backports a commit which fixes a use after free bug in awk.
CVE-2022-30065 description:
A use-after-free in Busybox 1.35-x's awk applet leads to denial of
service and possibly code execution when processing a crafted awk
pattern in the copyvar function.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 8b383ee2a0)
This update contains only a security fix for an issue in chsh and chfn,
but OpenWrt is not packaging these applications so OpenWrt is not
affected. In OpenWrt master this was already fixed by the update to
util-linux 2.38.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
