This patch adds support for the Accton WR6202 Mini 3G broadband router.
Full details for this device are available at
http://www.awbnetworks.com/products03.php?Fullkey=19.
This device is identical to the SMCWBR11S-3GN:
http://www.smc-asia.com/products03.php?Fullkey=210
It's also worth noting that this board has a GPIO line to control the
power to the USB port.
[juhosg:
- fix checkpatch warnings,
- reorder Kconfig entry,
- merge the sysupgrade patch,
- add GPL header]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
SVN-Revision: 30434
This patch adds support for the Sitecom WL-341 v3 and other Sercomm
IP1006RRv2 based boards for sysupgrade support and for the initial
flash through pushbutton initiated recovery mode with the special
partition table and fixes for the quirks and things required by the
modified bootloader.
There is a known bug, Wi-Fi is not working on my board probably
because of the lack of RAM (the board only has 16MiB ram -- half of
the normal amount for non rebadged versions, but there is an empty
slot for another ram chip,) but I don't know for sure. The driver
loads but hostapd fails to load so I think it's not related to the
specific device except for the lack of RAM.
Moreover, only 7 of the 11 onboard leds are confirmed working, it
seems that one of the others is always on and the remaining ones are
connected to the wireless card leds already recognized by OpenWrt
[juhosg: reordered some parts in order to keep things sorted
alphabetically]
Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com>
SVN-Revision: 29910
In this patch:
* rename Argus leds to avoid underscores
* rename Belkin F5D8235 v1 leds from f5d8234 to f5d8235
* remove Belkin F5D8235 v1 status led defined as storage led (it was
defined as usb led earlier, just in wrong place) - it should have
router led as in v2
* add Argus, Sparklan and Belkin F5D8235 v2 status leds
* add Belkin F5D8235 v1 and v2 usb leds
* fix Belkin F5D8235 v2 network config generation and mac address axtraction
* fix Sparklan board identification
* add Sparklan usb led (this board doesn't have usb connector by
default and the led is hidden also but if you are going to solder
the connector then you'll see the led too)
* add Sparklan network config generation and mac address extraction
* fix empty string test in network script and...
* ...sort case entries by the first board in the list
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29871
Previously the tx housekeeping was done in a spin_lock_irqsave critical
section which causes irqs to be disabled during that time. Since the
housekeeping is already prepared to be scheduled as a tasklet process
the housekeeping only in softirq context and revise the locking between
the tx path and the housekeeping tasklet by using a normal spin_lock
which in most situations will be a NOP anyway.
This makes sure that interrupts are only disabled for a short time
since in the worst case the housekeeping might have to free up to 256
skbs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 29762
This add support for the Sitecom WL-351 v1 002.
In principle the Engenius ESR9850 should also work with this, but I
don't have the hardware to test it.
Since an external gigabit switch (RTL8366RB) is used,
I had to modify the ramips_esw driver to add a 'bypass' mode, which
just configures it to not filter the vlan tags.
Also two initialization words (FCT2 and FPA2) are set to different
values by u-boot than what the driver is using and it only seems to
work correctly when they not overridden by the driver, so I
added them to the platform specific data as reg_initval_fct2 and
reg_initval_fpa2.
With this wired lan works as expected, however I'm still having some
trouble with the wireless lan:
It only works after I rmmod & re-insmod rt2800pci and then
reconfigure it in the webinterface, but not directly after
rebooting.
The symptom of this is wpad saying:
Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: associated (aid 1)
Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> WPA: pairwise key handshake completed (RSN)
Dec 20 15:45:22 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: authenticated
But wpa_supplicant on the client saying:
Authentication with <wl351mac> timed out.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 29604
This patch adds support for the Omnima MiniEMBWiFi
Ralink RT3050F based board.
Based on a patch by Ivan Ignjatic <ivan at omnima.co.uk>
SVN-Revision: 29533
The preconfiguration of the USB LED has benn move to the
/etc/uci-defaults/leds script. [juhosg]
Signed-off-by: Adam Porter <porter.adam at gmail.com>
SVN-Revision: 28571
This patch adds initial board support for the MoFi Network MOFI3500-3GN
(Ralink RT3052F SoC, 8MB flash, 32MB ram, wireless N, USB-OTG). This
router is basically the NA version of the HW550-3G.
Signed-off-by: Layne Edwards <ledwards76@gmail.com>
SVN-Revision: 26466
This patch adds sysupgrade and status LED support for the Aztech
HW550-3G. Some LED GPIOs were changed for clarity.
Signed-off-by: Layne Edwards <ledwards76@gmail.com>
SVN-Revision: 26320
This patch adds initial support for the Aztech HW550-3G (Ralink
RT3052f SoC, 8MB flash, 32MB dram). Ethernet is not working yet.
Wireless appears to work fine. USB does not work yet (as with other
Ralink boards).
Signed-off-by: Layne Edwards <ledwards76@gmail.com>
SVN-Revision: 26123
