Add a ubus method to request link-measurements from connected STAs.
In addition to the STAs address, the used and maximum transmit power can
be provided by the external process for the link-measurement. If they
are not provided, 0 is used as the default value.
Signed-off-by: David Bauer <mail@david-bauer.net>
Problem exist when dnsmasq is exclusively bind to particular interface.
After reconfiguring or restarting this interface, its index changes, but
dnsmasq uses the old one. When this problem occurs, dnsmasq does not
listen on the correct interface so DHCP does not work, and clients do not
get an IP address. Procd netdev param can be added to restart dnsmasq when
the interface index is changed.
Signed-off-by: Valentyn Datsko <valikk.d@gmail.com>
[combined into a single &&-connected statement]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This package uses BPF to create a fast path which improves bridging performance
by bypassing the bridge layer. It also supports creating tc offload rules for
hardware that supports it.
Hardware offload support can be used with MT7622 + MT7915 once it is merged
Signed-off-by: Felix Fietkau <nbd@nbd.name>
860ca90 odhcpd: Support for Option NTP and SNTP
83e14f4 router: advertise removed addresses as invalid in 3 consecutive RAs
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Enable both the hunting-and-pecking loop and hash-to-element mechanisms
by default in OpenWRT with SAE.
Commercial Wi-Fi solutions increasingly frequently now ship with both
hunting-and-pecking and hash-to-element (H2E) enabled by default as this
is more secure and more performant than offering hunting-and-pecking
alone for H2E capable clients.
The hunting and pecking loop mechanism is inherently fragile and prone to
timing-based side channels in its design and is more computationally
intensive to perform. Hash-to-element (H2E) is its long-term
replacement to address these concerns.
For clients that only support the hunting-and-pecking loop mechanism,
this is still available to use by default.
For clients that in addition support, or were to require, the
hash-to-element (H2E) mechanism, this is then available for use.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
The 80211r r0kh and r1kh defaults are generated from the md5sum of
"$mobility_domain/$auth_secret". auth_secret is only set when using EAP
authentication, but the default key is used for SAE/PSK as well. In
this case, auth_secret is empty, and the default value of the key can
be computed from the SSID alone.
Fallback to using $key when auth_secret is empty. While at it, rename
the variable holding the generated key from 'key' to 'ft_key', to avoid
clobbering the PSK.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[make ft_key local]
Signed-off-by: David Bauer <mail@david-bauer.net>
Add the STAs extended capabilities to the ubus STA information. This
way, external daemons can be made aware of a STAs capabilities.
This field is of an array type and contains 0 or more bytes of a STAs
advertised extended capabilities.
Signed-off-by: David Bauer <mail@david-bauer.net>
Recently the hostapd has undergone many changes. The patches were not refreshed.
Refreshed with
make package/hostapd/{clean,refresh}
Refreshed:
- 380-disable_ctrl_iface_mib.patch
- 600-ubus_support.patch
- 700-wifi-reload.patch
- 720-iface_max_num_sta.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
Up to now the WPS script triggered WPS on the stations only if it
could not trigger it successfully on any hostapd instance.
In a Multi-AP context, there can be a need (to establish a new
wireless backhaul link) to trigger WPS on the stations, regardless of
whether there is already a hostapd instance configured or not. The
current script makes it impossible, as if hostapd is running and
configured, WPS would always be triggered on hostapd only.
To allow both possibilities, the following changes are made:
- Change the "pressed" action to "release", so that we can make use of
the "$SEEN" variables (to know for how long the button was pressed).
- If the button is pressed for less than 3 seconds, keep the original
behavior.
- If the button is pressed for 3 seconds or more, trigger WPS on the
stations, regardless of the status of any running hostapd instance.
- Add comments explaining both behaviors.
- While at it, replace the usage of '-a' with a '[] && []'
construct (see [1]).
This gives users a "fallback" mechanism to onboard a device to a
Multi-AP network, even if the device already has a configured hostapd
instance running.
[1]: https://github.com/koalaman/shellcheck/wiki/SC2166
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
The auto-ht option already kept HT and VHT support, but wasn't updated
to support HE (11ax).
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Provide incoming BSS transition queries to ubus subscribers.
This allows external steering daemons to provide clients with
an optimal list of transition candidates.
This commit has no functional state in case no ubus subscriber is
present or it does not handle this ubus message.
To prevent hostapd from sending out a generic response by itself, a
subscribing daemon has to return a non-zero response code to hostapd.
Signed-off-by: David Bauer <mail@david-bauer.net>
Backport a patch to allow extending the ubus BSS-transition method
for specifying individual dialog tokens for BSS transition
management requests.
This is required for handling BSS transition queries in the future.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds a new struct for storing statistics not (yet) tracked by
hostapd regarding RRM and WNM activity.
These statistics can be read using the get_status hostapd interface ubus
method.
Signed-off-by: David Bauer <mail@david-bauer.net>
The 'fils_dhcp' option can be set to '*' in order to autodetect the DHCP server
For proto=dhcp networks, the discovered dhcp server will be used
For all other networks, udhcpc is called to discover the address
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add the beacon interval to hostapd status output. This allows external
services to discover the beacon interval for a specific VAP.
This way, external wireless management daemons can correctly calculate
fields containing TBTT value from absolute time-values.
Signed-off-by: David Bauer <mail@david-bauer.net>
If authentication fails repeatedly e.g. because of a weak signal, the link
can end up in blocked state. If one of the nodes tries to establish a link
again before it is unblocked on the other side, it will block the link to
that other side. The same happens on the other side when it unblocks the
link. In that scenario, the link never recovers on its own.
To fix this, allow restarting authentication even if the link is in blocked
state, but don't initiate the attempt until the blocked period is over.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When procd-ujail is available, 1f78538387 runs hostapd as user
"network", with only limited additional capabilities (CAP_NET_ADMIN and
CAP_NET_RAW).
hostapd_cli (CONFIG_PACKAGE_hostapd-utils) communicates with hostapd
over a named UNIX-domain socket. hostapd_cli is responsible for creating
this socket at /tmp/wpa_ctrl_$pid_$counter. Since it typically runs as
root, this endpoint is normally created with uid root, gid root, mode
0755. As a result, hostapd running as uid network is able to receive
control messages sent through this interface, but is not able to respond
to them. If debug-level logging is enabled (CONFIG_WPA_MSG_MIN_PRIORITY
<= 2 at build, and log_level <= 2 in /etc/config/wireless wifi-device),
this message will appear from hostapd:
CTRL: sendto failed: Permission denied
As a fix, hostapd_cli should create the socket node in the filesystem
with uid network, gid network, mode 0770. This borrows the presently
Android-only strategy already in hostapd intended to solve the same
problem on Android.
If procd-ujail is not available and hostapd falls back to running as
root, it will still be able to read from and write to the socket even if
the node in the filesystem has been restricted to the network user and
group. This matches the logic in
package/network/services/hostapd/files/wpad.init, which sets the uid and
gid of /var/run/hostapd to network regardless of whether procd-ujail is
available.
As it appears that the "network" user and group are statically allocated
uid 101 and gid 101, respectively, per
package/base-files/files/etc/passwd and USERID in
package/network/services/hostapd/Makefile, this patch also uses a
constant 101 for the uid and gid.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
[refreshed patch]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix the return value, shell return codes should be 0 to indicate success
(i.e. mount point found), 1 should be failure (i.e. mount point not-found).
Fixes: ac4e8aa ("dnsmasq: fix more dnsmasq jail issues")
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
19aae94 [build: avoid rebuilds of unset VARIANT packages] builds
packages defined without a VARIANT only once, using the first VARIANT
defined in the Makefile.
This caused problems with wpa-cli, as it is only built for variants that
include supplicant support, and the first VARIANT defined may not build
it.
The same happens to hostapd-utils, which is not built for
supplicant-only variants.
To circumvent this, set VARIANT=* for both packages so that they get
built for every defined variant. This should not cause spurious
rebuilds, since tey are not a dependency of any other package defined in
this Makefile.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
We can't use booleans, since we're not including stdbool.h. Use integers
instead.
Fixes: 0b79e7c01e ("dnsmasq: generate the dns object name dynamically")
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
dnsmasq may call hotplug.dhcp, hotplug.neigh and hotplug.tftp.
Only the first two callees were listed in the ACL, so add missing
hotplug.tftp.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A set of tags can be specified for --dhcp-host option to restrict the
assignment to the requests which match all the tags.
Example usage:
config vendorclass
option networkid 'udhcp'
option vendorclass 'udhcp'
config host
option mac '*:*:*:*:*:*'
list match_tag 'switch.10'
list match_tag 'udhcp'
option ip '192.168.25.10'
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
This implements the mapping recommendations from RFC8325, with an
update from RFC8622. This ensures that DSCP marked packets are properly
sorted into WMM classes.
The map can be disabled by setting iw_qos_map_set to something invalid
like 'none'
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Package hostapd-common is a dependency of every other package defined in
hostpad Makefile. It is currently built next to the bottom of that
Makefile's package list.
If you run make back to back, then check-compile will compare the
hostapd-common timestamp to the variant being compiled, to decide if the
varint needs to be rebuilt or not. Since the hostapd-conf package is
built towards the end of the list, it will be newer than most of the
variants, causing unnecessary package rebuilds.
Move it to the top, so that its timestamp will be older than dependent
packages, avoiding unnecessary rebuild of every selected variant.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Commit a2fcd3900c ("dnsmasq: improve init script") broke the existing
handling for hosts_dir. Remove the redundant mount again to fix it.
Reported-by: Hartmut Birr <e9hack@gmail.com>
Fixes: a2fcd3900c ("dnsmasq: improve init script")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* fix restart in LuCI (inherited umask was to restrictive)
* make directory of hosts-file (!= /tmp) accessible in ujail
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* SSH agent forwarding might cause security issues, locally and on the jump
machine (https://defn.io/2019/04/12/ssh-forwarding/). So allow to
completely disabling it.
* separate options for client and server
* keep it enabled by default
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
The 'madvise', syscall is missing.
Found with 'utrace /usr/sbin/umdns' on an R7800 and RT3200.
Signed-off-by: Michael Peleshenko <mpeleshenko@gmail.com>
