```
Specifications:
* CPU: Qualcomm IPQ8074A, SoC Version: 2.0, Quad core 1651 MHz
* RAM: 1 GiB of DDR3 466 MHz
* Flash: NAND 512 MiB (Winbond W29N04GZ)
* 6 RGB LEDs: Power, LAN1, LAN2, 2.4GHz, 5GHz H and 5GHz L
* UART: One 4-pin populated header next to the heatsink and a chip.
GND RXD TXD, beginning from the external antennas. 115200n8.
Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet 802.3bt/at
* One 100/1000 Gigabit Ethernet
Wlan:
* 4x4 in 2.4GHz : 802.11b/g/n/ax
* 4x4 in 5.0GHz L: 802.11a/n/ac/ax
* 4x4 in 5.0GHz H: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 2.86/4.41/4.98 dBi (2.4GHz/5GHz L/5GHz H)
Power:
* 802.3bt/at 30.1W
* DC 12V/3.5A
Mounting: Wall and ceiling
```
```
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect to the console on the AP, and connect the LAN port to your LAN
3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4. Set active_fw in env
4. Set active_fw in env
# setenv active_fw 1
5. Transfer the initramfs image with TFTP
# setenv serverip 192.168.1.10 (IP of TFTP server host)
# setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
# tftpboot openwrt-qualcommax-ipq807x-netgear_wax630-initramfs-uImage.itb
6. Reboot and load the image
# bootm
7. SCP factory image to the AP
# scp openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi root@192.168.1.1:/tmp/
8. Connect to device using SSH (use the LAN port)
9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
# cat /proc/mtd (To check MTD partitions)
# ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi
10. Set active_fw to 0
# /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
# reboot
```
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
As requested by the maintainers, the order for the WAX family
should be alphabetically. WAX620 is now after WAX218.
Files changed:
+ipq807x.mk
+01_leds
No changes to the content.
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 64GB eMMC or 128 MB SPI-NAND
RAM: 512MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
- UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | GND TX VCC RX | <= |
| ----------------- |
--------------------------
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Enter fakeroot, decompress the configuration:
tar -zxf cfg_export_config_file.conf
3. Edit 'etc/config/dropbear', set 'enable' to '1'.
4. Edit 'etc/shadow', update (remove) root password:
'root::19523:0:99999:7:::'
5. Repack 'etc' directory:
tar -zcf cfg_export_config_file.conf etc/
* If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
just ignore it.
6. Upload new configuration via web interface, now you can SSH to RAX3000M.
Check stroage type:
Check the label on the back of the device:
"CH EC CMIIT ID: xxxx" is eMMC version
"CH CMIIT ID: xxxx" is NAND version
eMMC Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'factory' part.
('data' partition can be ignored, it's useless.)
2. Write new GPT table:
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
IP 192.168.1.254, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync
NAND Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'Factory' part.
2. Erase and write new BL2:
mtd erase BL2
mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2
3. Erase and write new FIP:
mtd erase FIP
mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, erase UBI volumes:
ubidetach -p /dev/mtd0
ubiformat -y /dev/mtd0
ubiattach -p /dev/mtd0
8. Create new ubootenv volumes:
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb
10. Perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Allwinner H6 needs this driver to enable DVFS support.
May also be used with H616/H618 SoC in the future.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Kernel 5.15 already supports the NanoPi R1 and NanoPi R1S H5,
and they use new LED bindings that do not match the existing
settings in 01_leds. Update led settings to fixes that.
List the led node on NanoPi R1S H5:
root@OpenWrt:~# ls /sys/class/leds/
green:lan green:wan red:status
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
This will help switching to newer 5.15 kernels. This backport required
rebasing Northstar's USB host patch.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The IXP4xx crypto module must be loaded after the rootfs is
up as it depends on loading some NPE microcode from the file
system.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This resurrects the support for IXP4xx using device tree
rather than the old (deleted) board files. The final pieces
of IXP4xx board files were deleted in Linux v5.19.
Ext4 root filesystems on CF and USB are supported by the
default config.
We support these three initial targets:
- The Gateworks Avila GW2348 reference design has 64MB of RAM
and 32MB of flash and also supports USB and CompactFlash.
- The Gateworks Cambria GW2358 reference design has 128MB of
RAM and 32MB of flash and also supports USB and CompactFlash.
- The old and stable Linksys NSLU2 works fine as well, albeit
it only has 32MB of RAM so it has been marked as non-default.
The 8MB of flash can only fit the kernel, so it has been
patched to boot from exteral media on USB. I have used
it successfully as a NAS with ksmbd and LUCI web API, see:
https://dflund.se/~triad/krad/ixp4xx/
Signed-off-by: Howard Harte <hharte@magicandroidapps.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
This is a backport of the patch to support the Altima AMI101L
PHY which is merged for the v6.7 kernel. This PHY is used in the
IXP4xx-based USRobotics USR8200.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a backport of the patch for byte addressed IO to the
Epson RTC7301 driver. This is used by the IXP4xx-based
USRobotics USR8200.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Among other changes this commit makes Linux use correct switch ports
again.
Fixes: a4792d79e8 ("bcm53xx: backport DT changes from v6.5")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This backports patches
leds: turris-omnia: convert to use dev_groups
leds: turris-omnia: Use sysfs_emit() instead of sprintf()
leds: turris-omnia: Drop unnecessary mutex locking
leds: turris-omnia: Do not use SMBUS calls
leds: turris-omnia: Make set_brightness() more efficient
leds: turris-omnia: Support HW controlled mode via private trigger
leds: turris-omnia: Add support for enabling/disabling HW gamma correction
leds: turris-omnia: Fix brightness setting and trigger activating
into backport-5.15.
The above patches replace:
leds: turris-omnia: support HW controlled mode via private trigger
leds: turris-omnia: initialize multi-intensity to full
leds: turris-omnia: change max brightness from 255 to 1
from mvebu/patches-5.15.
Signed-off-by: Marek Behún <kabel@kernel.org>
This reverts commit 0c117e1f6c.
Activate the lantiq/xrx200 target again.
There are still some problems with the GSWIP, but it is not leaking
packets to the wrong bridge in normal operations.
It shows some error messages at configuration like these:
[ 54.308861] gswip 1e108000.switch: port 5 failed to add ce:9d:84:d1:81:f0 vid 1 to fdb: -22
[ 54.325633] gswip 1e108000.switch: port 5 failed to add e8🇩🇪27:95:c1:b4 vid 0 to fdb: -22
[ 54.351242] gswip 1e108000.switch: port 5 failed to add e8🇩🇪27:95:c1:b4 vid 1 to fdb: -22
[ 54.358311] gswip 1e108000.switch: port 5 failed to delete ce:9d:84:d1:81:f0 vid 1 from fdb: -2
The problems are described in this pull request:
https://github.com/openwrt/openwrt/pull/13200
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
1) clear nvram partialboots upon successful boot
This behavior is already defined for EA9500; enabled for EA9200 too.
2) fix MAC address in board.d/02_network
Use the correct nvram variable to derive lan/wan MAC address.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Set correct GPIO (10) for the WPS button. This matches GPIO settings in
vendor GPL sources. Note that GPL sources also mention a USB indicator
LED (GPIO 13) but the device has neither an external USB port nor a USB LED.
In addition, prefixes (button-, led-) are added to relevant DT entries,
as well as color and function specifications for LEDs.
Closes: #13736
Reported-by: Waldemar Czabaj <kaball@wp.pl>
Signed-off-by: Rani Hod <rani.hod@gmail.com>
(added led mitigations for wifi leds)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This backports patches
leds: turris-omnia: Use sysfs_emit() instead of sprintf()
leds: turris-omnia: Drop unnecessary mutex locking
leds: turris-omnia: Do not use SMBUS calls
leds: turris-omnia: Make set_brightness() more efficient
leds: turris-omnia: Support HW controlled mode via private trigger
leds: turris-omnia: Add support for enabling/disabling HW gamma correction
leds: turris-omnia: Fix brightness setting and trigger activating
into backport-6.1.
The above patches replace:
leds: turris-omnia: support HW controlled mode via private trigger
leds: turris-omnia: initialize multi-intensity to full
leds: turris-omnia: change max brightness from 255 to 1
from mvebu/patches-6.1.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
This is an RTL8382-based switch with 24 copper ports + 4 SFP ports
Specifications:
---------------
* SoC: Realtek RTL8382M
* Flash: 32 MiB SPI flash
* RAM: 256 MiB
* Ethernet: 24x 10/100/1000 Mbps
* Buttons: 1x "Reset" button
* UART: 1x serial header, unpopulated
* SFP: 4 SFP ports
Works:
------
- (24) RJ-45 ethernet ports
- Switch functions
- Buttons
- Sys LED on front panel (no port LEDs)
Not yet enabled:
----------------
- Port LEDs (no driver for RTL8231 in this mode)
- SFP cages (no driver for PHY)
Install via web interface:
-------------------------
Not supported at this time.
Install via serial console/tftp:
--------------------------------
The U-Boot firmware drops to a TP-Link specific "BOOTUTIL" shell at
38400 baud. There is no known way to exit out of this shell, and no
way to do anything useful.
Ideally, one would trick the bootloader into flashing the sysupgrade
image first. However, if the image exceeds 6MiB in size, it will not
work. To install OpenWRT:
Prepare a tftp server with:
1. server address: 192.168.0.146
2. the image as: "uImage.img"
Power on device, and stop boot by pressing any key.
Once the shell is active:
1. Ground out the CLK (pin 16) of the ROM (U6)
2. Select option "3. Start"
3. Bootloader notes that "The kernel has been damaged!"
4. Release CLK as soon as bootloader thinks image is corrupted.
5. Bootloader enters automatic recovery -- details printed on console
6. Watch as the bootloader flashes and boots OpenWRT.
Blind install via tftp:
-----------------------
This method works when it's not feasible to install a serial header.
Prepare a tftp server with:
1. server address: 192.168.0.146
2. the image as: "uImage.img"
3. Watch network traffic (tcpdump or wireshark works)
4. Power on the device.
5. Wait 1-2 seconds then ground out the CLK (pin 16) of the ROM (U6)
6. When 192.168.0.30 makes tftp requests, release pin 16
7. Wait 2-3 minutes for device to auto-flash and boot OpenWRT
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Like with some other ipq40xx devices, the kernel image size for the WPJ428
is limited in stock u-boot. For that reason, the current release doesn't
include an image for the board.
By switching to the zImage format, the kernel image size is reduced which
re-enables the build process. The image boots and behaved normally through
a few days of testing.
Before the switch to kernel version 6.1, it was possible to reduce the
image size by enough when disabling UBIFS and its otherwise unneeded
dependencies.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
prepend-dtb got extended to handle the Meraki devices too,
the problem here was that the Netgear WNDR4700 expects an
u-boot header in front of the DTB, whereas Meraki devices
don't.
Since the header was dropped, the WNDR4700's uboot started
to complain:
Bad Magic Number,it is forbidden to be written to flash!!
when flashing the factory.img since it expects an u-boot
header there.
Fixes: 5dece2d9355a ("apm821xx: switch over from DTB_SIZE to DEVICE_DTC_FLAGS")
Reported-by: @kisgezenguz
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Doing a simple ping to my device shows this:
64 bytes from 10.0.253.101: icmp_seq=1 ttl=64 time=2.00 ms
64 bytes from 10.0.253.101: icmp_seq=2 ttl=64 time=2.02 ms
64 bytes from 10.0.253.101: icmp_seq=3 ttl=64 time=1.68 ms
64 bytes from 10.0.253.101: icmp_seq=4 ttl=64 time=1.91 ms
64 bytes from 10.0.253.101: icmp_seq=5 ttl=64 time=1.92 ms
64 bytes from 10.0.253.101: icmp_seq=6 ttl=64 time=2.04 ms
Some users even report higher values on older kernels:
64 bytes from 192.168.1.10: seq=0 ttl=64 time=0.612 ms
64 bytes from 192.168.1.10: seq=1 ttl=64 time=2.852 ms
64 bytes from 192.168.1.10: seq=2 ttl=64 time=2.719 ms
64 bytes from 192.168.1.10: seq=3 ttl=64 time=2.741 ms
64 bytes from 192.168.1.10: seq=4 ttl=64 time=2.808 ms
The problem is that the governor is set to Ondemand, which causes
the CPU to clock all the way down to 48MHz in some cases.
Switching to performance governor:
64 bytes from 10.0.253.101: icmp_seq=1 ttl=64 time=0.528 ms
64 bytes from 10.0.253.101: icmp_seq=2 ttl=64 time=0.561 ms
64 bytes from 10.0.253.101: icmp_seq=3 ttl=64 time=0.633 ms
64 bytes from 10.0.253.101: icmp_seq=4 ttl=64 time=0.526 ms
In theory, using the Performance governor should increase power draw,
but it looks like it really does not matter for this soc.
Using a calibrated precision DC power supply (cpu idle):
Ondemand
24.00V * 0.134A = 3.216 Watts
48.00V * 0.096A = 4.608 Watts
Performance
24.00V * 0.135A = 3.240 Watts
48.00V * 0.096A = 4.608 Watts
Let's simply switch to the Performance governor by default
to fix the general jittery behaviour on devices using this soc.
Tested on: MikroTik wAP ac
Fixes: #13649
Reviewed-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Copy configuration to boot partition (partition 1) instead of root
partition (partition 2) because the root partition is not writable if
it's a suqashfs image.
Move configuration back to root during preinit.
Fixes: https://github.com/openwrt/openwrt/issues/13695
Signed-off-by: Christian Buschau <cbuschau@d00t.de>
At this moment, 702-phy-Add-2.5G-SGMII-interface-mode.patch cause error
durring kernel compilation:
CC drivers/net/phy/phylink.o
drivers/net/phy/phylink.c: In function 'phylink_get_capabilities':
drivers/net/phy/phylink.c:443:9: error: enumeration value 'PHY_INTERFACE_MODE_2500SGMII' not handled in switch [-Werror=switch]
443 | switch (interface) {
| ^~~~~~
cc1: all warnings being treated as errors
NXP take care of it. Let's port their patch.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Patches recreated from NXP 6.1 tree:
400-LF-20-3-mtd-spi-nor-Use-1-bit-mode-of-spansion-s25fs.patch
701-staging-add-fsl_ppfe-driver.patch
702-phy-Add-2.5G-SGMII-interface-mode.patch
Patch 703 includes changes made by Christian Marangi, extracted from commit
0d4a547905.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Some MT7915 devices need to load the second part of the eeprom to
work properly. The mt76 driver is not yet ready to read the pre-cal
data via the NVMEM cell. Therefore, partially revert commit to fix
the device probe issue on some devices.
P.S.
Except for D-Link and Ubnt devices, It is still uncertain whether
pre-cal data is required for other devices in the patch.
This partially reverts commit 9ac891f8c4.
Fixes: https://github.com/openwrt/openwrt/issues/13700
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Telco Electronics X1 has MT7603E and MT7612E PCIe NICs. They are
driven by kmod-mt7603 and kmod-mt76x2.
Ref: 73e0f52b6e ("ramips: add support for Telco Electronics X1")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The starting address of 'factory' partition is 0x40000, and the
starting address of the next partition is 0x50000. It's obvious
that the correct size for the 'factory' is 0x10000, just like
other MT7620 devices.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
These three devices uses MT7612E PCIe NIC and supported by the
'mt76' driver. So the right frequency limit property should be
`ieee80211-freq-limit`.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
On the ramips target, all 'wmac' nodes in SoC dtsi are enabled by
default except mt7628. There is no need to mark them as 'okay'
again. So these useless properties can be removed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
