This uses "GPL-2.0-or-later" header for files identified using scancode
license scanner with 100% score as GPL 2.0 or later.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Specifications:
SOC: Qualcomm Atheros TP9343 (750 MHz)
Flash: 8 Mb (GigaDevice GD25Q64CSIG)
RAM: 64 Mb (Zentel A3R12E40DBF-8E)
Serial: yes, 4-pin header
Wlan: Qualcomm Atheros TP9343, antenna: MIM0 3x3:3 RP-SMA
3 x 2.4GHz power amp module Skyworks (SiGe) SE2576L
Ethernet: Qualcomm Atheros TP9343
Lan speed: 100M ports: 4
Lan speed: 100M ports: 1
Other info: same case, ram and flash that TP-Link TL-WR841HP,
different SOC
https://forum.openwrt.org/t/adding-device-support-tp-link-wr941hp/
Label MAC addresses based on vendor firmware:
LAN *:ee label
WAN *:ef label +1
WLAN *:ee label
The label MAC address found in "config" partition at 0x8
Flash instruction:
Upload the generated factory firmware on web interface.
Signed-off-by: Diogenes Rengo <rengocbx250@gmail.com>
[remove various whitespace issues, squash commits, use short 0x0]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Compile with Ninja. Ninja compiles faster and is more stable with
parallel builds. Routines copied from cmake.mk.
Speed improves from:
Executed in 127.47 secs fish external
usr time 17.02 mins 446.00 micros 17.02 mins
sys time 1.18 mins 40.00 micros 1.18 mins
to:
Executed in 118.91 secs fish external
usr time 17.28 mins 499.00 micros 17.28 mins
sys time 1.13 mins 45.00 micros 1.13 mins
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The Canadian edition of the TP-Link Archer A6 v3 uses a different header, but
otherwise it's identical to the already supported EU/US editions.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Brian Lee <dev@leebrian.me>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
The patch adds support for the TP-Link Archer C6 v3 (FCC ID TE7A6V3)
The patch adds identification changes to the existing TP-Link Archer A6,
by Vinay Patil <post2vinay@gmail.com>, which has identical hardware.
Specification
-------------
MediaTek MT7621 SOC
RAM: 128MB DDR3
SPI Flash: W25Q128 (16MB)
Ethernet: MT7530 5x 1000Base-T
WiFi 5GHz: Mediatek MT7613BE
WiFi 2.4GHz: Mediatek MT7603E
UART/Serial: 115200 8n1
Device Configuration & Serial Port Pins
---------------------------------------
ETH Ports: LAN4 LAN3 LAN2 LAN1 WAN
_______________________
| |
Serial Pins: | VCC GND TXD RXD |
|_____________________|
LEDs: Power Wifi2G Wifi5G LAN WAN
Build Output
------------
The build will generate following set of files
[1] openwrt-ramips-mt7621-tplink_archer-c6-v3-initramfs-kernel.bin
[2] openwrt-ramips-mt7621-tplink_archer-c6-v3-squashfs-factory.bin
[3] openwrt-ramips-mt7621-tplink_archer-c6-v3-squashfs-sysupgrade.bin
How to Use - Flashing from TP-Link Web Interface
------------------------------------------------
* Go to "Advanced/System Tools/Firmware Update".
* Click "Browse" and upload the OpenWrt factory image: factory.bin[2]
* Click the "Upgrade" button, and select "Yes" when prompted.
TFTP Booting
------------
Setup a TFTP boot server with address 192.168.0.5.
While starting U-boot press '4' key to stop autoboot.
Copy the initramfs-kernel.bin[1] to TFTP server folder, rename as test.bin
From u-boot command prompt run tftpboot followed by bootm.
Recovery
--------
Archer A6 V3 has recovery page activated if SPI booting from flash fails.
Recovery page can be activated by powercycling the router four times
before the boot process is complete.
Note: TFTP boot can be activated only from u-boot serial console.
Device recovery address: 192.168.0.1
Signed-off-by: Amish Vishwakarma <vishwakarma.amish@gmail.com>
[fix indent]
Signed-off-by: David Bauer <mail@david-bauer.net>
ninja is faster at building cmake packages than make, and according to reports
also more reliable at handling parallel builds
This commit includes a patch that adds GNU make jobserver support, in order to
allow more precise control over the number of parallel tasks
Enable parallel build by default for packages using ninja
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
CPExxx and WBSxxx boards with AR9344 SOC
use the OKLI lzma kernel loader
with the offset of 3 blocks of length 4k (0x3000)
in order to have a fake "kernel" that cannot grow larger
than how it is defined in the now static OEM partition table.
Before recent changes to the mtdsplit driver,
the uImage parser for OKLI only supported images
that started exactly on an eraseblock boundary.
The mtdsplit parser for uImage now supports identifying images
with any magic number value
and at any offset from the eraseblock boundary
using DTS properties to define those values.
So, it is no longer necessary to use fixed sizes
for kernel and rootfs
Tested-by: Andrew Cameron <apcameron@softhome.net> [CPE510 v2]
Tested-by: Bernhard Geier <freifunk@geierb.de> [WBS210 v2]
Tested-by: Petrov <d7c48mWsPKx67w2@gmail.com> [CPE210 v1]
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This patch adds support for TP-Link Archer C6U v1 (EU).
The device is also known in some market as Archer C6 v3.
This patch supports only Archer C6U v1 (EU).
Specifications:
--------------
* SoC: Mediatek MT7621AT 2C2T, 880MHz
* RAM: 128MB DDR3
* Flash: 16MB SPI NOR flash (Winbond 25Q128)
* WiFi 5GHz: Mediatek MT7613BEN (2x2:2)
* WiFi 2.4GHz: Mediatek MT7603EN (2x2:2)
* Ethernet: MT7630, 5x 1000Base-T.
* LED: Power, WAN, LAN, WiFi 2GHz and 5GHz, USB
* Buttons: Reset, WPS.
* UART: Serial console (115200 8n1), J1(GND:3)
* USB: One USB2 port.
Installation:
------------
Install the OpenWrt factory image for C6U is from the
TP-Link web interface.
1) Go to "Advanced/System Tools/Firmware Update".
2) Click "Browse" and upload the OpenWrt factory image:
openwrt-ramips-mt7621-tplink_archer-c6u-v1-squashfs-factory.bin.
3) Click the "Upgrade" button, and select "Yes" when prompted.
Recovery to stock firmware:
--------------------------
The C6U bootloader has a failsafe mode that provides a web
interface (running at 192.168.0.1) for reverting back to the
stock TP-Link firmware. The failsafe interface is triggered
from the serial console or on failed kernel boot. Unfortunately,
there's no key combination that enables the failsafe mode. This
gives us two options for recovery:
1) Recover using the serial console (J1 header).
The recovery interface can be selected by hitting 'x' when
prompted on boot.
2) Trigger the bootloader failsafe mode.
A more dangerous option is force the bootloader into
recovery mode by erasing the OpenWrt partition from the
OpenWrt's shell - e.g "mtd erase firmware". Please be
careful, since erasing the wrong partition can brick
your device.
MAC addresses:
-------------
OEM firmware configuration:
D8:07:B6:xx:xx:83 : 5G
D8:07:B6:xx:xx:84 : LAN (label)
D8:07:B6:xx:xx:84 : 2.4G
D8:07:B6:xx:xx:85 : WAN
Signed-off-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
The patch adds support for the TP-Link Archer A6 v3
The router is sold in US and India with FCC ID TE7A6V3
Specification
-------------
MediaTek MT7621 SOC
RAM: 128MB DDR3
SPI Flash: W25Q128 (16MB)
Ethernet: MT7530 5x 1000Base-T
WiFi 5GHz: Mediatek MT7613BE
WiFi 2.4GHz: Mediatek MT7603E
UART/Serial: 115200 8n1
Device Configuration & Serial Port Pins
---------------------------------------
ETH Ports: LAN4 LAN3 LAN2 LAN1 WAN
_______________________
| |
Serial Pins: | VCC GND TXD RXD |
|_____________________|
LEDs: Power Wifi2G Wifi5G LAN WAN
Build Output
------------
The build will generate following set of files
[1] openwrt-ramips-mt7621-tplink_archer-a6-v3-initramfs-kernel.bin
[2] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-factory.bin
[3] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-sysupgrade.bin
How to Use - Flashing from TP-Link Web Interface
------------------------------------------------
* Go to "Advanced/System Tools/Firmware Update".
* Click "Browse" and upload the OpenWrt factory image: factory.bin[2]
* Click the "Upgrade" button, and select "Yes" when prompted.
TFTP Booting
------------
Setup a TFTP boot server with address 192.168.0.5.
While starting U-boot press '4' key to stop autoboot.
Copy the initramfs-kernel.bin[1] to TFTP server folder, rename as test.bin
From u-boot command prompt run tftpboot followed by bootm.
Recovery
--------
Archer A6 V3 has recovery page activated if SPI booting from flash fails.
Recovery page can be activated from serial console only.
Press 'x' while u-boot is starting
Note: TFTP boot can be activated only from u-boot serial console.
Device recovery address: 192.168.0.1
Thanks to: Frankis for Randmon MAC address fix.
Signed-off-by: Vinay Patil <post2vinay@gmail.com>
[remove superfluous factory image definition, whitespacing]
Signed-off-by: David Bauer <mail@david-bauer.net>
This adjusts the Makefile to use the new option to turn off the
doc builds. It will not cause any problems except a warning
about unused options if combined with a ccache source missing
the upstream patch.
Since a config setting is required to re-enable the doc build this
is equivalent to unconditionally disabling the docs if the config
setting is not created.
Signed-off-by: David Adair <djabhead@aol.com>
Prevent build error on Alpine Linux host:
libfakeroot.c error: conflicting types for 'id_t'
Error relocating openwrt/staging_dir/host/lib/libfakeroot.so: SEND_GET_XATTR: symbol not found
Signed-off-by: Ruslan Isaev <legale.legale@gmail.com>
The ZyXEL NR7101 prepend an additional header to U-Boot images. This
header use the TRX magic 0x30524448 (HDR0), but is incompatible with
TRX images.
This code is reverse-engineered based on matching 32 bit numbers
found in the header with lengths and different checksum
calculations of the vendor images found on the device. The result
was matched against the validation output produced by the
bootloader to name the associated header fields.
Example bootloader validation output:
Zyxel TRX Image 1 --> Found! Header Checksum OK
============ZyXEL header information==================
chipId : MT7621A
boardId : NR7101
modelId : 07 01 00 01
kernel_len : (14177560)
kernelChksum : (0x8DD31F69)
swVersionInt : 1.00(ABUV.0)D1
swVersionExt : 1.00(ABUV.0)D1
Zyxel TRX Image 2 --> Found! Header Checksum OK
============ZyXEL header information==================
chipId : MT7621A
boardId : NR7101
modelId : 07 01 00 01
kernel_len : (14176660)
kernelChksum : (0x951A7637)
swVersionInt : 1.00(ABUV.0)D0
swVersionExt : 1.00(ABUV.0)D0
=================================================
Check image validation:
Image1 Header Magic Number --> OK
Image2 Header Magic Number --> OK
Image1 Header Checksum --> OK
Image2 Header Checksum --> OK
Image1 Data Checksum --> OK
Image2 Data Checksum --> OK
Image1 Stable Flag --> Stable
Image1 Try Counter --> 0
Image1: OK
Image2: OK
The coverage and algorithm for the kernelChksum field is unknown.
This field is not validated by the bootloader or the OEM firmware
upgrade tool. It is therefore set to a static value for now.
The swVersion fields contain free form string values. The OEM firmware
use ZyXEL structured version numbers as shown above. The strings are
not interpreted or validated on boot, so they can be repurposed for
anything we want the bootloader to display to the user. But the OEM
web GUI fails to flash images with freeform strings.
The purpose of the other strings in the header is not known. The
values appear to be static. We assume they are fixed for now, until
we have other examples. One of these strings is the platform name,
which is taken as an input parameter for support other members of
the device family.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
The stock firmware does not accept firmware with "Talon" in the name.
Tested on firmware version 1.0.10 Build 20160902 rel. 57400 which came
preinstalled, as well as latest firmware version 2.0.1 Build 20170103
rel.71053 flashed from
AD7200v1-up-ver2-0-1-P1[20170103-rel71053]_2017-01-04_10.08.28.bin.
Fixes: 1a775a4fd0 ("ipq806x: add support for TP-Link Talon AD7200")
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
[added details about vendor firmware]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add "-i" option for reading & displaying firmware info. First it lists
in-firmware partitions ("fwup-ptn"). Then it checks for human
understandable partitions and prints data found in each of them.
This new feature is meant for development & debug purposes.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The old code didn't make sense as it was using "len" variable which was
guaranteed to be always 0. Loop right above broken code is:
while (len > 0) { }
With this recent ALIGN macro fix this resulted in subtracting block size
from 0 and calling write_out_padding() with a negative length.
To calculate amount of bytes needed for padding & alignment it should be
enough to use % 4.
Fixes: a2f6622945 ("firmware-utils: fix few random warnings")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes:
src/zyimage.c:10:0: warning: "_POSIX_SOURCE" redefined
src/zyimage.c:11:0: warning: "_POSIX_C_SOURCE" redefined
This change has been tested on Linux with -Wextra and on Mac OS.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Currently it's not possible to flash factory images on devices shipped
with vendor firmware versions 1.1.0 Build 20201120 rel. 50406 (published
2020-12-22):
(curFw_ver, newFw_ver) == (1.1, 1.0) [NM_Error](nm_checkSoftVer) 00848: Firmwave not supports, check failed.
[NM_Error](nm_checkUpdateContent) 01084: software version dismatched
[NM_Error](nm_buildUpgradeStruct) 01188: checkUpdateContent failed.
They've even following note in release notes:
Note: You will be unable to downgrade to the previous firmware version
after updating this firmware.
This version check in vendor firmware is implemented in
/usr/bin/nvrammanager binary likely as following C code[1]:
sscanf(buf, "%d.%d.%*s",&upd_fw_major, &upd_fw_minor);
...
if (((int)upd_fw_major < (int)cur_fw_major) ||
((ret = 1, cur_fw_major == upd_fw_major && (upd_fw_minor < (int)cur_fw_minor)))) {
ret = 0;
printf("[NM_Error](%s) %05d: Firmwave not supports, check failed.\r\n\r\n","nm_checkSoftVer" ,0x350);
}
...
return ret;
So in order to fix this and make it future proof it should be enough to
ship our factory firmware images with major version 7 (lucky number).
Tested on latest firmware version 1.1.2 Build 20210125 rel.37999:
Firmwave supports, check OK.
(curFw_ver, newFw_ver) == (1.1, 7.0) check firmware ok!
Flashing back to vendor firmware
c7v5_us-up-ver1-1-2-P1[20210125-rel37999]_2021-01-25_10.33.55.bin works
as well:
U-Boot 1.1.4-gbec22107-dirty (Nov 18 2020 - 18:19:12)
...
Firmware downloaded... filesize = 0xeeae77 fileaddr = 0x80060000.
Firmware Recovery file length : 15642231
Firmware process id 2.
handle_fw_cloud 146
Image verify OK!
Firmware file Verify ok!
product-info:product_name:Archer C7
product_ver:5.0.0
special_id:55530000
[Error]sysmgr_cfg_checkSupportList(): 1023 @ specialId 45550000 NOT Match.
Firmware supports, check OK.
Firmware Recovery check ok!
1. https://gist.github.com/ynezz/2e0583647d863386a66c3d231541b6d1
Signed-off-by: Petr Štetiar <ynezz@true.cz>
bcm4908img is a tool managing BCM4908 platform images. It's used for
creating them as well as checking, modifying and extracting data from.
It's required by both: host (for building firmware images) and target
(for sysupgrade purposes). Make it a host/target package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
JFFS2 bootfs partition in a BCM4908 image usually includes some padding.
For flashing it individually (writing to designed MTD partition) we want
just JFFS2 data.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's required for upgrading firmware using single partitions instead of
just blindly writing whole image.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's much easier to operate on BCM4908 image data with absolute offset
of each section stored. It doesn't require summing sizes over and over.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This adds support for accessing bootfs JFFS2 partition in the BCM4908
image. Support includes:
1. Listing files
2. Renaming file (requires unchanged name length)
Above commands are useful for flashing BCM4908 images which by defualt
come with cferom.000 file and require renaming it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's important for modifying / extracting firmware content. cferom is
optional image content at the file beginning.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
1. Don't allow pipe stdin as we need to fseek()
2. Don't alow TTY as it doesn't make sense for binary input
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Netgear uses CHK header which needs to be skipped when validating
BCM4908 image. Detect it directly in the bcm4908img tool. Dealing with
binary structs and endianess is way simpler in C.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Move code parsing existing firmware file to separated function. This
cleans up existing code and allows reusing parsing code for other
commands.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Update to the latest stable release.
This fixes a segfault and build failure seen compiling the 5.10 kernel
for x86/64. With this update, builds complete and sparse generates the
usual large volume of warnings as on 5.4 kernels.
Reported-by: Javier Marcet <javier@marcet.info>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This allows to specify an own magic instead of using the default magic
value TRX_MAGIC. If no own magic is specified the default one will be
used.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Discovered by coverty:
CID 1473630: Code maintainability issues (UNUSED_VALUE)
Assigning value from "type_to_guid_and_name(type, &name)" to
"part_guid" here, but that stored value is overwritten before it can
be used.
Remove the now redundant assignment of part_guid which is also set
conditionally later on.
Fixes: 4a078bd135 ("firmware-utils/ptgen: fix partition guid and name")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This old ELF library dating to 2009 used to be necessary on MacOS but
is not required for building the kernel or tools since [1]. On Linux
systems, libelf is already an OpenWRT build-system prerequisite [2].
Presence of the older library can mask or conflict with the system libelf
and lead to build errors, as seen compiling Linux kernels since v5.8 or
host tools such as dwarves (e.g. pahole).
Remove the unnecessary tools/libelf library and avoid the related issues.
[1] 5f8e587240 ("build: force disable stack validation during kernel build
on non-linux systems")
[2] https://openwrt.org/docs/guide-developer/build-system/install-buildsystem#prerequisites
Tested-by: Rosen Penev <rosenp@gmail.com> (Linux)
Tested-by: Georgi Valkov <gvalkov@abv.bg> (MacOS)
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Add patches for mkimage to allow using it instead of the binary-only
'bromimage' tool to generate bl2 for MT7622.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Do not align partitions with sectors. Only kb align
for GPT is supported.
Use 254 heads and 63 sectors for PMBR.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Adding -H option copies partition to MBR after pmbr entry.
Max 3 partitions can be copied to MBR.
Hybrid MBR is needed only in special cases.
For example mt7622 SD card boot needs MBR entry with boot
flag enabled.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Don't download all of vim just to build xxd. Use a tight tarball
containing only xxd sources instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
U-Boot requires xxd to create the default environment from an external
file as done in uboot-mediatek.
Build xxd (only, not the rest of vim) as part of tools to make sure it
is present on the buildhost.
Reported-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow setting GPT partition names as used by TF-A bl2 to identify the
FIP volume to load from eMMC and SD-card.
While at it, also allow setting 'required' attribute as it should be
used for volumes which are essential for the system to boot.
Also properly handle setting the LEGACY_BOOT flag on the partition
selected as 'active', as this is how it is specified in the spec.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
mediatek-mt7622 as well as mediatek-mt7623 require CPIO to create their
initramfs images. So build CPIO as part of the host toolchain.
Signed-off-by: David Bauer <mail@david-bauer.net>
The TP-Link EAP235-Wall is a wall-mounted, PoE-powered AC1200 access
point with four gigabit ethernet ports.
When connecting to the device's serial port, it is strongly advised to
use an isolated UART adapter. This prevents linking different power
domains created by the PoE power supply, which may damage your devices.
The device's U-Boot supports saving modified environments with
`saveenv`. However, there is no u-boot-env partition, and saving
modifications will cause the partition table to be overwritten. This is
not an issue for running OpenWrt, but will prevent the vendor FW from
functioning properly.
Device specifications:
* SoC: MT7621DAT
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (MT7603EN): b/g/n, 2x2
* Wireless 5GHz (MT7613BEN): a/n/ac, 2x2
* Ethernet: 4× GbE
* Back side: ETH0, PoE PD port
* Bottom side: ETH1, ETH2, ETH3
* Single white device LED
* LED button, reset button (available for failsafe)
* PoE pass-through on port ETH3 (enabled with GPIO)
Datasheet of the flash chip specifies a maximum frequency of 33MHz, but
that didn't work. 20MHz gives no errors with reading (flash dump) or
writing (sysupgrade).
Device mac addresses:
Stock firmware uses the same MAC address for ethernet (on device label)
and 2.4GHz wireless. The 5GHz wireless address is incremented by one.
This address is stored in the 'info' ('default-mac') partition at an
offset of 8 bytes.
From OEM ifconfig:
eth a4:2b:b0:...:88
ra0 a4:2b:b0:...:88
rai0 a4:2b:b0:...:89
Flashing instructions:
* Enable SSH in the web interface, and SSH into the target device
* run `cliclientd stopcs`, this should return "success"
* upload the factory image via the web interface
Debricking:
U-boot can be interrupted during boot, serial console is 57600 baud, 8n1
This allows installing a sysupgrade image, or fixing the device in
another way.
* Access serial header from the side of the board, close to ETH3,
pin-out is (1:TX, 2:RX, 3:GND, 4:3.3V), with pin 1 closest to ETH3.
* Interrupt bootloader by holding '4' during boot, which drops the
bootloader into its shell
* Change default 'serverip' and 'ipaddr' variables (optional)
* Download initramfs with `tftpboot`, and boot image with `bootm`
# tftpboot 84000000 openwrt-initramfs.bin
# bootm
Revert to stock:
Using the tplink-safeloader utility from the firmware-utils package,
TP-Link's firmware image can be converted to an OpenWrt-compatible
sysupgrade image:
$ ./staging_dir/host/bin/tplink-safeloader -B EAP235-WALL-V1 \
-z EAP235-WALLv1_XXX_up_signed.bin -o eap235-sysupgrade.bin
This can then be flashed using the OpenWrt sysupgrade interface. The
image will appear to be incompatible and must be force flashed, without
keeping the current configuration.
Known issues:
- DFS support is incomplete (known issue with MT7613)
- MT7613 radio may stop responding when idling, reboot required.
This was an issue with the ddc75ff704 version of mt76, but appears to
have improved/disappeared with bc3963764d.
Error notice example:
[ 7099.554067] mt7615e 0000:02:00.0: Message 73 (seq 1) timeout
Hardware was kindly provided for porting by Stijn Segers.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
* The fit image is now created with 0666 permission in upstream U-Boot
remove our patch switch creates it with 0744
* The generated/autoconf.h file is created now as an empty file, it is
not needed to remove this include any more.
* Upstream lib/rsa/rsa-sign.c now includes stdlib.h instead of malloc.h
* ALIGN_MASK was moved to imagetool.h, own patch should not be needed
any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Multiple sources are hosted on OpenWrts source server only. The source
URLs to point to the server vary based on different epochs in OpenWrts
history.
Replace all by @OPENWRT which is an "empty" mirror, therefore using the
fallback servers sources.cdn.openwrt.org and sources.openwrt.org.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Although provided in separate zip archives, the firmwares for EU
and RU version are byte-identical. This adds the missing ID compared
to the support-list in the vendor firmware.
Note (since I checked it anyway):
Partitions and support list are unchanged for all three existing
firmware versions:
* 20200721-rel40773
* 20201029-rel43238
* 20201120-rel50399
Signed-off-by: Alexey Kunitskiy <alexey.kv@gmail.com>
[rewrite commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Switch to the normal tarball instead of the codeload generated one. The
latter has the potential to change hashes based on changes in the repo.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Asus looks for an extra data at the end of BCM4908 image, right before
the BCM4908 tail. It needs to be properly filled to make Asus accept
firmware image.
This tool constructs such a tail, writes it and updates CRC32 in BCM4908
tail accordingly.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Flashing image with BCM4908 CFE bootloader requires specific firmware
format. It needs 20 extra bytes with magic numbers and CRC32 appended.
This tools allows appending such a tail to the specified image and also
verifying CRC32 of existing BCM4908 image.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
BCM4908 CFE bootloader requires kernel to be prepended with a custom
header. This simple tool implements support for such headers.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It looks like GitHub changed the URL path for release tarballs, thus the
download for the zstd package was always falling back to the OpenWrt
sources mirror.
Fix the GitHub URL for one which works. The file hash remains unchanged.
Signed-off-by: David Bauer <mail@david-bauer.net>
Previously, ccache would end up using the system libzstd, which is not
supposed to be a build requirement.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
Instead of using an ancient qemu version in-tree the building machine
should just have qemu-utils installed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
cmake is a dependency of ccache, which means it is build before ccache
is available and hence must be build with non-ccache CC and CXX. It
currently works, because the cmake build system splits the compiler
variable and treats them as multiple compilers to check.
For "ccache gcc" it first tests for "ccache", which always fails,
because ccache is not a compiler by itself, even if it is available, and
then ends up calling "gcc" alone, effectively never using ccache.
Let's make this explicit by forcing the use of non-ccache CC and CXX.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
use PKG_FIXUP:=autoreconf to generate configure
200-hide-dlsym-error.patch deleted due to fixed upstream in another way
other patches refreshed to reflect latest changes
Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
Device hardware: https://deviwiki.com/wiki/TP-LINK_AD7200_(Talon)
The Talon AD7200 is basically an Archer C2600 with a third PCIe lane
and an 802.11ad radio. It looks like the Archers C2600/5400 but the
housing is slightly larger.
Specifications
--------------
- IPQ8064 dual-core 1400MHz
- QCA9988 2.4GHz WiFi
- QCA9990 5GHz WiFi
- QCA9500 60GHz WiFi
- 32MB SPI Flash
- 512MiB RAM
- 5 GBit Ports (QCA8337)
Installation
------------
Installation is possible from the OEM web interface.
Sysupgrade is possible.
TFTP recovery is possible.
- Image: AD7200_1.0_tp_recovery.bin
Notes
- This will be the first 802.11ad device supported by mainline.
Signed-off-by: Gary Cooper <gaco@bitmessage.de>
glibc started to return errors from dlerror() for dlsym() lookup failures which
results in a lot of messages from fakeroot like
dlsym(acl_get_fd): staging_dir/host/lib/libfakeroot.so: undefined symbol: acl_get_fd
dlsym(acl_get_file): staging_dir/host/lib/libfakeroot.so: undefined symbol: acl_get_file
dlsym(acl_set_fd): staging_dir/host/lib/libfakeroot.so: undefined symbol: acl_set_fd
when building OpenWrt using a recent glibc. Use the patch from the upstream
Debian package to silence these messages.
Link: https://bugs.debian.org/830912
Fixes: FS#3393
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Upstream switched to building with CMake. Adjust accordingly.
Reapplied patch as upstream changed the file format.
Added HOST_BUILD_PARALLEL for faster compilation.
Added cmake tool dependency and removed circular dependencies as a
result.
Adjusted dependent tools to use NOCACHE as they are needed to build
ccache.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This reverts commit b1952dc259 as it's
causing issues on the buildbot which uses some kind of ccache wrapper
and so the breakage needs to be investigated further:
bash: cmake: command not found
time: tools/ccache/compile#0.05#0.03#0.15
ERROR: tools/ccache failed to build.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Some Russian d-link routers require that their firmware be signed with a
salted md5 checksum followed by the bytes 0x00 0xc0 0xff 0xee. This tool
signs factory images the OEM's firmware accepts them.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
The Ubiquiti Network airCube AC is a cube shaped device supporting
2.4 GHz and 5 GHz with internal 2x2 MIMO antennas.
It can be powered with either one of:
- 24v power supply with 3.0mm x 1.0mm barrel plug
- 24v passive PoE on first LAN port
There are four 10/100/1000 Mbps ports (1 * WAN + 3 * LAN).
First LAN port have optional PoE passthrough to the WAN port.
SoC: Qualcomm / Atheros AR9342
RAM: 64 MB DDR2
Flash: 16 MB SPI NOR
Ethernet: 4x 10/100/1000 Mbps (1 WAN + 3 LAN)
LEDS: 1x via a SPI controller (not yet supported)
Buttons: 1x Reset
Serial: 1x (only RX and TX); 115200 baud, 8N1
Missing features:
- LED control is not supported
Physical to internal switch port mapping:
- physical port #1 (poe in) = switchport 2
- physical port #2 = switchport 3
- physical port #3 = switchport 5
- physical port #4 (wan/poe out) = switchport 4
Factory update is tested and is the same as for Ubiquiti AirCube ISP
hence the shared configuration between that devices.
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
Upstream switched to building with CMake. Adjust accordingly.
Reapplied patch as upstream changed the file format.
Added HOST_BUILD_PARALLEL for faster compilation.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This adds new strings for the v3.20 to the support list of the
already supported TP-Link CPE510 v3.
The underlying hardware appears to be the same, similar to the
situation with CPE210 v3.20 in 4a2380a1e7 ("tplink-safeloader:
expand support list for TP-Link CPE210 v3")
Signed-off-by: Gioacchino Mazzurco <gio@altermundi.net>
[extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Because some padding values in the TP-Link safeloader image generation
were hardcoded, different values were sometimes used throughout a
factory image. TP-Link's upgrade images use the same value everywhere,
so let's do the same here.
Although a lot of TP-Link's safeloader images have padded partition
payloads, images for the EAP-series of AC devices don't. This padding is
therefore also made optional.
By replacing the type of the padding value byte with a wider datatype,
new values outside of the previously valid range become available. Use
these new values to denote that padding should not be performed.
Because char might be signed, also replace the char literals by a
numeric literal. Otherwise '\xff' might be sign extended to 0xffff.
This results in factory images differing by 1 byte for:
* C2600
* ARCHER-C5-V2
* ARCHERC9
* TLWA850REV2
* TLWA855REV1
* TL-WPA8630P-V2-EU
* TL-WPA8630P-V2-INT
* TL-WPA8630P-V2.1-EU
* TLWR1043NDV4
* TL-WR902AC-V1
* TLWR942NV1
* RE200-V2
* RE200-V3
* RE220-V2
* RE305-V1
* RE350-V1
* RE350K-V1
* RE355
* RE450
* RE450-V2
* RE450-V3
* RE500-V1
* RE650-V1
The following factory images no longer have padding, shrinking the
factory images by a few bytes for:
* EAP225-OUTDOOR-V1
* EAP225-V3
* EAP225-WALL-V2
* EAP245-V1
* EAP245-V3
Signed-off-by: Sander Vanheule <sander@svanheule.net>
TP-Link safeloader firmware images contain a number of (small)
partitions with information about the device. These consist of:
* The data length as a 32-bit integer
* A 32-bit zero padding
* The partition data, with its length set in the first field
The OpenWrt factory image partitions that follow this structure are
soft-version, support-list, and extra-para. Refactor the code to put all
common logic into one allocation call, and let the rest of the data be
filled in by the original functions.
Due to the extra-para changes, this patch results in factory images that
change by 2 bytes (not counting the checksum) for three devices:
* ARCHER-A7-V5
* ARCHER-C7-V4
* ARCHER-C7-V5
These were the devices where the extra-para blob didn't match the common
format. The hardcoded data also didn't correspond to TP-Link's (recent)
upgrade images, which actually matches the meta-partition format.
A padding byte is also added to the extra-para partition for EAP245-V3.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
rules.mk always passes these as -I/-L to the toolchain.
Fixes rare errors like:
cc1: error: staging_dir/target-aarch64_cortex-a53_musl/usr/include: No such file or directory [-Werror=missing-include-dirs]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Paul Spooren <mail@aparcar.org>
Acked-by: Rosen Penev <rosenp@gmail.com>
Drop our local sstrip copy and use the current ELFKickers upstream
version.
Patch the original makefile in order to avoid building elftoc, since it
fails with musl's elf.h. This is fine, since we only need sstrip anyway.
Finally, add the possibility to pass additional arguments to sstrip and
pass -z (remove trailing zeros) by default, which matches the behaviour
of the previous version.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[shorten long commit msg lines]
Signed-off-by: Paul Spooren <mail@aparcar.org>
