Make installation to eMMC more convenient on the BPi-R64 by also
copying the production image (if valid) from SD Card to eMMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of building all U-Boot variants by default, build only those
needed by the selected board(s).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add kmod-mdio-devres package and kernel config symbol, and update related
kmod-r8169 and kmod-ixgbe package dependencies.
Build tested module dependencies on x86/64 with CONFIG_ALL_KMODS=y.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The ZyXEL GS1900-8 is a 8 port switch without any PoE functionality or
SFP ports, but otherwise similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-8 v1.2
* SoC: Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash: Macronix MX25L12835F 16 MiB
* RAM: Nanya NT5TU128M8GE-AC 128 MiB DDR2 SDRAM
* Ethernet: 8x 10/100/1000 Mbit
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
8 ethernet port status LEDs (green, SoC controlled)
* Buttons: 1 on-off glide switch at the back (not configurable)
1 reset button at the right side, behind the air-vent
(not configurable)
1 reset button on front panel (configurable)
* Power 12V 1A barrel connector
* UART: 1 serial header (JP2) with populated standard pin connector on
the left side of the PCB, towards the back. Pins are labelled:
+ VCC (3.3V)
+ TX (really RX)
+ RX (really TX)
+ GND
the labelling is done from the usb2serial connector's point of
view, so RX/ TX are mixed up.
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
Instructions are identical to those for the GS1900-10HP and GS1900-8HP.
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-10HP is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only boot off the first partition anyway (hardcoded in the DTS). To
make sure we are manipulating the first partition, issue the following
commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-generic-zyxel_gs1900-8-squashfs-sysupgrade.bin
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
3d7da7a igmpproxy tidy some loose ends
c84ba0f rcigmpproxy: add entries to /etc when creating /etc/igmpproxy.conf
5a18967 adds igmpproxy skeleton
7e6a218 logread: support resolving dns names
e39ca8b netifd: add support for /etc/udhcpc.user
7952bd0 odhcp6c: support /etc/odhcp6c.user
ba0eb4e swconfig, fwenv, agent
4556b8a pppd cosmetic
9324d9d pppd: sends AT commands to model using /dev/ttyUSBN
417b14a ttydev: add some more ttyUSB
ed739dc example: dont depend on policycoreutils
97613f9 dropbear: using dropbear as scp: dns name resolving
12c193b dropbear tcp connect ssh ports for scp
c050077 rcdnsmasq: remove redundant rule and make rcsysntpd optional
8c5de35 this is a bug
8d5c463 uhttpd rcboot rcdnsmasq
094266e hostapd and wpa_supplicant
aef0bd7 mountroot: maintains /tmp/sysupgrade.tar
24f0406 dropbear: allow it to read tmp.fs files
2901433 firstboot mkfsf2fs rcboot
2c4afb7 blockmount mmc
465ca98 adds industrial i/o (iio) nodedev
82f686e mtd stordev: back that ubiblock0_4p1 up with a filecon
7df78bd ubus: "support" older ubusd versions that run as root
4458bce swconfig: allow using terminal (to print output)
e8d606d sslcert: openssl linked: this shaves off 200 bytes
93afffb jshn ntpdhotplug
0b847f0 wpad: reads /etc/ssl/openssl.cnf
f14ee34 indent fix
a0c7cad mtd, uhttpd, ubus and ntpdhotplug
d74f98f adds a not about checkreqprot requirement in some scenarios
affacce example: add policycoreutils-setfiles for make check
4f944dc kmodloader and fwenv:
efe36a3 netifd: adds a comment/reminder
581b087 more fw_printenv loose ends
30177a4 fw_setenv: needs mtd write access to set and delete env
da28f4c fw_printenv: some minor clean ups
a062053 fw_printenv missing rules
244ba5f blockmount: extroot and /rwm
0745a6a squid: allow squid to run sslcrtd with domain transition
b851df6 squid fix
8c55acd squid: adds certfile and allow connect http but...
b7c1f6d Makefile: exclude tinyproxy from mintesttgt (using squid)
5ff39bd squid: forgot about luci
5366c97 squid/rcsquid some basic fill in
8743da6 squid skeleton
687a43b adds squid 3128 port to httpproxy port
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
Commit f4da28c301 ("elfutils: Add host build") supplied a libelf host
library to fix a glib2 host build error, but this need was later removed
by b6212c8769 ("glib2: don't use libelf during host build").
More importantly, there are already two sources for libelf host libraries:
OpenWRT build prerequisites [1] and tools/libelf. A third is not needed.
Ref [1]: https://openwrt.org/docs/guide-developer/build-system/install-buildsystem#prerequisites
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Import patch form Frank Wunderlich <frank-w@public-files.de> to fix
build of MediaTek AHCI SATA driver.
Enable that driver on Bananapi BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[ -d /sys/module/xfrm_interface ] is enough to check if
CONFIG_XFRM_INTERFACE support was enabled in kernel.
Signed-off-by: Alin Nastac <alin.nastac@technicolor.com>
Copy patch added to uboot-sunxi by commit 3cc57ba462
("uboot-sunxi: add missing type __u64") also to uboot-mediatek.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* make sure USB 2.0 works (useful for UEFI-booting eg. memtest86)
* include more useful U-Boot config options on BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MediaTek published their current U-Boot patchset on github:
https://github.com/mtk-openwrt/u-boot/commits/mtksoc
Import the platform patches from there (`00-mtk-*.patch`), arrange,
them nicely, drop no longer needed local patches and rebase on top of
U-Boot 2021.04-rc3.
Tested and works well on Linksys E8450 (snand-1ddr) as well as
Bananapi BPi-R64 (sdmmc-2ddr, emmc-2ddr).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Most prominently this adds changes which allow replacing the binary-
only 'bromimage' tool by U-Boot's 'mkimage' (see previous commit).
This fixes build on non-Linux and/or non-x86 platforms.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add patches for mkimage to allow using it instead of the binary-only
'bromimage' tool to generate bl2 for MT7622.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
d3f2041 uci: manually clear uci_ptr flags after uci_delete() operations
ccb7517 sys: packagelist: drop ABI version from package name
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Document the existence of this feature. This allows the user to execute a script
at each DHCPv4 event. This is useful, for example, as an ad-hoc way to update a
DDNS entry when (and only when) required.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Document the existence of this feature. This allows the user to execute a script
at each DHCPv6 event. This is useful, for example, as an ad-hoc way to update a
DDNS entry when (and only when) required.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
d464187c policycoreutils: sestatus belongs to bin not sbin
d59932a7 policycoreutils: Resolve path in restorecon_xattr
5682c0d5 policycoreutils/fixfiles.8: add missing file systems and merge check and verify
57dd1f65 policycoreutils/setfiles: Drop unused nerr variable
be7f54cb setfiles: drop ABORT_ON_ERRORS and related code
9207823c setfiles: Do not abort on labeling error
c064d214 selinux_config(5): add a note that runtime disable is deprecated
8bc865e1 newrole: support cross-compilation with PAM and audit
ba2d6c10 fixfiles: correctly restore context of mountpoints
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
142826a3 libselinux: fix segfault in add_xattr_entry()
398d2cee libselinux: rename gettid() to something which never conflicts with the libc
8f0f0a28 selinux(8,5): Describe fcontext regular expressions
9cc6b5cf libselinux/getconlist: report failures
156dd0de libselinux: update getseuser
e2dca5df libselinux: accept const fromcon in get_context API
da4829d0 libselinux: Always close status page fd
45b15c22 selinux(8): explain that runtime disable is deprecated
3c16aaef selinux(8): mark up SELINUX values
c2a58cc5 libselinux: LABEL_BACKEND_ANDROID add option to enable
db0f2f38 libselinux: Add build option to disable X11 backend
4a142ac4 libsepol: Bump libsepol.so version
d23342a9 libselinux: convert matchpathcon to selabel_lookup()
7ef5b185 libselinux: Change userspace AVC setenforce and policy load messages to audit format.
f5d644c7 libselinux: Add additional log callback details in man page for auditing.
075f9cfe libselinux: Fix selabel_lookup() for the root dir.
a4149e0e libselinux: Add new log callback levels for enforcing and policy load notices.
a63f93d8 libselinux: initialize last_policyload in selinux_status_open()
ef902db9 libselinux: safely access shared memory in selinux_status_updated()
9e4480b9 libselinux: Remove trailing slash on selabel_file lookups.
21fb5f20 libselinux: use full argument specifiers for security_check_context in man page
e7abd802 libselinux: fix build order
05bdc031 libselinux: use kernel status page by default
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
a9e0004f libsepol: invalidate the pointer to the policydb if policydb_init fails
6238e025 libsepol/cil: fix NULL pointer dereference in cil_fill_ipaddr
b69d77bc libsepol/cil: handle SID without assigned context when writing policy.conf
0861c659 libsepol: Validate policydb values when reading binary policy
8f5409cf libsepol: Create function ebitmap_highest_set_bit()
0451adeb libsepol/cil: Destroy disabled optional blocks after pass is complete
32f8ed3d libsepol/cil: introduce intermediate cast to silence -Wvoid-pointer-to-enum-cast
4662bdc1 libsepol/cil: be more robust when encountering <src_info>
6b561058 libsepol/cil: fix NULL pointer dereference with empty macro argument
0d0e47c7 libsepol/cil: Fix integer overflow in the handling of hll line marks
1b36ace2 libsepol: include header files in source files when matching declarations
1f1fa9d4 libsepol: uniformize prototypes of sepol_mls_contains and sepol_mls_check
72a88d75 libsepol: remove unused files
eba0ffee libsepol/cil: Fix heap-use-after-free when using optional blockinherit
1048f8d3 libsepol/cil: unlink blockinherit->block link when destroying a block
b3202918 libsepol/cil: fix memory leak when a constraint expression is too deep
f0d98f83 libsepol/cil: Fix heap-use-after-free in __class_reset_perm_values()
5d021d66 libsepol/cil: Update symtab nprim field when adding or removing datums
34bd9a9d libsepol: destroy filename_trans list properly
bdf4e332 libsepol/cil: fix NULL pointer dereference when parsing an improper integer
b7ea65f5 libsepol/cil: destroy perm_datums when __cil_resolve_perms fails
228c06d9 libsepol/cil: fix out-of-bound read in cil_print_recursive_blockinherit
a25d9104 libsepol/cil: constify some strings
e2d01842 libsepol/cil: propagate failure of cil_fill_list()
6c8fca10 libsepol/cil: do not add a stack variable to a list
38a09b74 libsepol/cil: fix NULL pointer dereference when using an unused alias
3c357285 libsepol/cil: remove useless print statement
90809674 libsepol/cil: always destroy the lexer state
d16a1e46 libsepol/cil: Use the macro FLAVOR() whenever possible
2aac859a libsepol/cil: Use the macro NODE() whenever possible
d317b470 libsepol/cil: Remove unnecessary assignment in cil_resolve_name_keep_aliases()
9b9761cf libsepol/cil: Remove unused field from struct cil_args_resolve
e257d4c7 libsepol/cil: Get rid of unnecessary check in cil_gen_node()
ebba2b00 libsepol/cil: cil_tree_walk() helpers should use CIL_TREE_SKIP_*
89dab467 libsepol: free memory when realloc() fails
2d353bd5 libsepol/cil: Give error for more than one true or false block
4a142ac4 libsepol: Bump libsepol.so version
506c7b95 libsepol: Drop deprecated functions
ae58e84b libsepol: Get rid of the old and duplicated symbols
c97d63c6 libsepol: silence potential NULL pointer dereference warning
64387cb3 libsepol: drop confusing BUG_ON macro
521e6a2f libsepol/cil: fix signed overflow caused by using (1 << 31) - 1
a152653b libsepol/cil: Fix neverallow checking involving classmaps
734e4beb libsepol/cil: Validate conditional expressions before adding to binary policy
685f577a libsepol/cil: Validate constraint expressions before adding to binary policy
8206b8cb libsepol: implement POLICYDB_VERSION_COMP_FTRANS
42ae834a libsepol,checkpolicy: optimize storage of filename transitions
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
945d0d7 utils: fix C style in header file
2cfc26f inittab: detect active console from kernel if no console= specified
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix: bpftools 5.11.2 does not compile on macOS, because the -m option
was placed between src and dst. Corrected by moving -m 644 before src.
Signed-off-by: Georgi Valkov <gvalkov@abv.bg>
The pkgconfig file hardcodes a host library directory which cannot be
overridden by OpenWrt during builds. Use SED to fix this and potential
include directory problems, as is done with several other packages.
This fixes a strange issue intermittently seen building iproute2 on the
oxnas target:
iptables modules directory: /usr/lib/iptables
libc has setns: yes
SELinux support: no
libbpf support: no
libbpf version 0.3.0 is too low, please update it to at least 0.1.0
LIBBPF_FORCE=on set, but couldn't find a usable libbpf
Fixes: 2f0d672088 ("bpftools: add utility and library packages
supporting eBPF usage")
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Make packages depending on usb-serial selective, so we do not have
to add kmod-usb-serial manually for every device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Partially restore the wild-card matching for kmod-usb3 modules to fix
build on platforms without PCI which otherwise file, as seen on
buildbot:
ERROR: module '[...]/linux-5.4.102/drivers/usb/host/xhci-pci.ko' is missing.
modules/usb.mk:1675: recipe for target '[...]/kmod-usb3_5.4.102-1_mips_mips32.ipk' failed
Fixes: 7bda2e9aba ("kernel: fix kmod-usb3 dependencies")
Fixes: be23f9818a ("apm821xx: add support for kernel 5.10")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove unneeded delcarations form package Makefile now that everything
comes from github.com/mtk-openwrt upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Adding CONFIG_USB_XHCI_PCI_RENESAS to KCONFIG made it so it was set
for all targets that included kmod-usb3, not just the intended
apm821xx/nand. xhci-pci has a dependency on xhci-pci-renesas if
CONFIG_USB_XHCI_PCI_RENESAS is set, breaking kmod-usb3 builds on
Linux 5.10 on all other targets.
Rework the dependencies by breaking out xhci-hcd, xhci-mtk, and
xhci-pci-renesas into new hidden kernel modules and setting kmod-usb3
dependencies properly.
Tested by building mt7621 and apm821xx/nand with kmod-usb3 on Linux 5.10
Fixes: be23f981 ("apm821xx: add support for kernel 5.10")
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
DDR3_FLYBY has accidentally been set also for the 1-chip variant which
lead to broken, unbootable images. Fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch copies over refreshed patches from 5.4.
- dropped crypto patches (they got upstreamed)
- dropped renesas USB 3 firmware loader (they got upstreamed)
- NAND now needs extra device-properties for ECC settings.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* allow MAC address from U-Boot env to be inhertied
* allow eMMC installation to succeed also without recovery present
on the SD Card.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All necessary blobs are now contained in the upstream repository, no
more wild replacing of blobs needed.
This new version also contains new storage drivers for (SPI-)NAND which
already comes with support for FM35Q1GA, so that patch can be dropped
as well.
Tested on:
* Bananapi BPi-R64
- sdmmc-2ddr
- emmc-2ddr
* Linksys E8450
- snand-1ddr
All works fine (booting Bananapi BPi-R64 from SD Card does NOT require
a signed image, so patch arm-trusted-firmware-mediatek to allow doing
that).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This will use the new application led trigger backend. For now this is
the only package that uses leds trigger in user space to configure the
kernel led triggers.
The callback script only emmits a message for now, so that this LED is now
managed by the rssileds service. Until now a generic warning was emitted that
this LED trigger is not supported. But that is not true.
-> Skipping trigger 'rssileds' for led '<name>' due to missing kernel module
I think this callback should be changed in the future to restart the
service.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
For now we have only kernel LED trigger support. With this change it is now
possible to use application triggers.
If we configure a LED with a non kernel trigger, then we check on every
restart and boot of the LED service if we have this trigger as an application
in "/usr/libexec/led-trigger". If this file with the name is found, then we
execute this to init the LED.
Possible use cases are:
- Start/Stop/Restart an application led trigger service for this led
- Init a LED that is configured by a hotplug script (VPN tunnel established)
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
stropts.h is unavailable under glibc (and unneeded when building
against glibc). Include it only if not building against glibc.
Reported-by: @DazzyWalkman
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Don't try to install files which no longer exist
Since {e,sd}mmc are now produced by ptgen they have been removed.
Fixes: 5a3562cd1d ("arm-trusted-firmware-mediatek: remove {e,sd}mmc headers")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Turned out those are simply MBR with active boot partition. And not
needed at all on emmc. Remove them as ptgen can now generate hybrid
MBR sufficient to boot MT7622 from SD Card.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Write everything needed for eMMC install into the gaps between
partitions on SD card. In that way, installation to eMMC only needs
the SD card, no additional files need to be loaded via TFTP any more.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
p2p_add_device() may remove the oldest entry if there is no room in the
peer table for a new peer. This would result in any pointer to that
removed entry becoming stale. A corner case with an invalid PD Request
frame could result in such a case ending up using (read+write) freed
memory. This could only by triggered when the peer table has reached its
maximum size and the PD Request frame is received from the P2P Device
Address of the oldest remaining entry and the frame has incorrect P2P
Device Address in the payload.
Fix this by fetching the dev pointer again after having called
p2p_add_device() so that the stale pointer cannot be used.
This fixes the following security vulnerabilities/bugs:
- CVE-2021-27803 - A vulnerability was discovered in how p2p/p2p_pd.c
in wpa_supplicant before 2.10 processes P2P (Wi-Fi Direct) provision
discovery requests. It could result in denial of service or other
impact (potentially execution of arbitrary code), for an attacker
within radio range.
Fixes: 17bef1e97a50 ("P2P: Add peer entry based on Provision Discovery Request")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Changes:
- Remove custom Build/Compile because it's no longer needed
- Remove std=gnu99 which is added automaticaly by igmpproxy if needed
- Remove -Dlog from CFLAGS because igmpproxy doesn't have log function
Signed-off-by: Jan Pavlinec <jan.pavlinec@nic.cz>
libunwind dependency check does not allow for MIPS64 arch. Add MIPS64 awareness.
libunwind seems to support MIPS64 without issues, it was limited by the dep arch
check in the Makefile.
Used to compile Suricata6/Rust locally without issue.
Signed-off-by: Donald Hoskins <grommish@gmail.com>
Non Linux systems e.g. macOS lack the __u64 type and produce build errors:
In file included from tools/aisimage.c:9:
In file included from include/image.h:19:
In file included from ./arch/arm/include/asm/byteorder.h:29:
In file included from include/linux/byteorder/little_endian.h:13:
include/linux/types.h:146:9: error: unknown type name '__u64'; did you mean '__s64'?
typedef __u64 __bitwise __le64;
Resolved by declaring __u64 in include/linux/types.h
Build tested on macOS and Ubuntu.
Signed-off-by: Georgi Valkov <gvalkov@abv.bg>
Compile and run-tested on malta/mip32be, using bpftool directly and also
libbpf (linked with tc) to inspect and load simple eBPF programs.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The latest iproute2 version brings various improvements and fixes:
https://git.kernel.org/pub/scm/network/iproute2/iproute2.git/log/?qt=range&q=v5.10.0..v5.11.0
In particular, ip and tc now use libbpf as the standard way to load BPF
programs, rather than the old, limited custom loader. This allows more
consistent and featureful BPF program handling e.g. support for global
initialized variables.
Also fix a longstanding problem with iproute2 builds where unneeded DSO
dependencies are added to most utilities, bloating their installation
footprint. From research and testing, explicitly using a "--as-needed"
linker flag avoids the issue. Update accordingly and drop extra package
dependencies from Makefile.
Additional build and packaging updates include:
- install missing development header to iproute2/bpf_elf.h
- propagate OpenWrt verbose flag during build
- update and refresh patches
Compile and run tested: QEMU/malta-mips32be on kernels 5.4 & 5.10.
All iproute2 packages were built and installed to the test image. Some
regression testing using ip-full and tc was successfully performed to
exercise several kmods, tc modules, and simple BPF programs.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Simplify cmake option handling by putting everything in blocks.
Add openssl patch as there's no easy way to disable.
Rebase the skip manpages patch.
Remove the monitor mode patch as it no longer applies.
Remove flex patch as normal Makefile is no longer used.
Remove USB path patch. While it is deprecated, the codepath is never
taken. /sys/bus/usb/devices is checked before hand. If it exists, the
function does stuff and returns. Additionally, this path is used
elsewhere in the code.
Refresh other patches.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
NTPD in busybox has option -I to bind server to IFACE.
However, capabilities of the busybox are limited, the -I option cannot be
repeated and only one interface can be effectively specified in it.
This option is currently not configurable via UCI.
The patch adds an interface option to the system config, ntp section.
Also sort options for uci_load_validate alphabetically.
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
with u-boot v2020.07 some variables have been renamed so this patch needs to be adjusted
otherwise at least with macOS as build system there are build errors
Signed-off-by: Ronny Kotzschmar <ro.ok@me.com>
The QOS feature depends on KPI2UDP which was removed from the tree with
commit a95775e4b2 ("drop unmaintained packages") in 2012.
Since QOS was the last user of the KPI, the feature can be disabled by
default.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The following warnings are shown during build:
/usr/include/vdsl/cmv_message_format.h:33:6: warning: "MEI_SUPPORT_DEBUG_STREAMS" is not defined, evaluates to 0 [-Wundef]
#if (MEI_SUPPORT_DEBUG_STREAMS == 1)
^~~~~~~~~~~~~~~~~~~~~~~~~
/usr/include/vdsl/drv_mei_cpe_interface.h:2256:6: warning: "MEI_SUPPORT_OPTIMIZED_FW_DL" is not defined, evaluates to 0 [-Wundef]
#if (MEI_SUPPORT_OPTIMIZED_FW_DL == 1)
^~~~~~~~~~~~~~~~~~~~~~~~~~~
The headers are provided by the MEI driver, but the defines are never
set by the vdsl app. While the struct with the
MEI_SUPPORT_OPTIMIZED_FW_DL conditional isn't used by the vdsl app,
however CMV_USED_PAYLOAD_8BIT_SIZE which value depends on
MEI_SUPPORT_DEBUG_STREAMS is.
Since the MEI driver doesn't provide an autogenerated header with
compile flags, the flags are hardcoded for the vdsl app.
Set them for the MEI driver as well, to indicate a relation to the
values used for the vdsl app and to be not surprised by a changed
default in case the MEI driver gets updated. Use the current default
values defined in the MEI driver.
Signed-off-by: Mathias Kresin <dev@kresin.me>
a857b45 resolv/locale: eventually this should be more efficient
11ed281 some more optimization
764a475 add redundant calls to file.search_conffile_dirs()
7d4558e fs: treat devtmpfs that same as tmpfs
81b677e adds irqbalance skeleton
5506244 irqbalance rules
cc96cd8 adds usbutil and gtpfdisk skels
01e2a55 some fsck, gptfdisk, mkfs and usbutil rules
d6d1e7d usbutil: output to terminal
da576fa fsck, gptfdisk and usbutil rules
09b39e9 unbound
241a029 hotplugcall: allow dac_read_search (is a subset of dac_override)
af0fe90 adds label for tcsh
160f79e adds tcpdump
6d02b96 adds coreutil execfile for busybox alternatives
ac54884 coreutilexecfile: these are known to require privileges, so exclude
8cb3b66 adds chrootexecfile
6d329d3 this saves 9KiB and its a bit more robust
88e2425 move addpart/delpart/partx to gptfdisk.cil
261012d ntphotplug: reads ubox data files
0473ace various
740e820 work through to genfs_seclabel_symlinks loose ends (Linux 5.10)
bef21f5 TODO adds a note about how I dont need to upgrade to polver 33 from 31
cb2e5a3 ubus uses ntpdhotplug fd, and some genfs_seclabel_symlink changes
07df9b9 luci, rpcd and wpad (mainly genfs_selabel related but not all)
8d86cab genfs_seclabel loose ends for blockmount, hotplugcall, irqbalance, zram-swap
b8156cd adds a note about how i forgot to target blockd
6e82ab8 adds blockd and related
254ff43 Makefile: exclude blockd from mintesttgt
4dc6bc2 pppd update related and unbound-odhcp rules
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Provide U-Boot variants for SD-card as well as eMMC boot, so we can
generate whole-disk images for the device.
While at it, rename 'mt7622' to 'mt7622-rfb1' to make it less confusing
now that more boards are being added.
Thanks to Frank Wunderlich (@frank-w) for making that nice SVG image
explaining the MMC boot process[1] and for providing the necessary
binary header blobs.
[1]: https://github.com/frank-w/BPI-R64-ATF
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add U-Boot environment configuration for the Linksys E8450 (UBI) to
allow access to the bootloader environment from OpenWrt via
'fw_printenv' and 'fw_setenv'.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Build U-Boot for the Linksys E8450 in order to have support for UBI.
The loader has a default environment with scripts handling the reset
button as well as fall-back to recovery firmware. If the loader comes
up without a valid environment found in UBI, it will automatically
make sure UBI is formatted and create a new environment and proceed
to load recovery firmware (either from UBI or via TFTP if recovery is
corrupted or unavailable).
If the button is held down during power-on, the yellow status LED
turns on and the bootloader environment is reset to factory defaults.
If the button is released at this point, the recovery firmware (if
existing) is loaded from UBI and booted.
If the button is continously held down even beyond the point that
the yellow LED turned on, the loader will try to load the recovery
firmware via TFTP from server 192.168.1.254, write it to UBI and
boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Linksys E8450 aka. Belkin RT3200 comes with a rather fresh brand
of SPI NAND storage. Add support for it to the nandx driver in
arm-trusted-firmware-mediatek, so we can boot from that chip.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of only relying in /sysupgrade.tgz being present in rootfs to
restore configuration, also grab /tmp/sysupgrade.tar which may have
magically gotten there during preinit...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
CHACHA_MIPS depends on CPU_MIPS32_R2. Therefore,
kmod-crypto-lib-chacha20 should not contain chacha-mips.ko on MIPS32 R1
targets. Enforce that in the target-specific definition.
Fixes bcm47xx, bcm63xx, lantiq/ase, ath25 builds.
Fixes: 06351f1 ("kernel: migrate wireguard into the kernel tree")
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
To the vast majority of the users, wireguard-tools are not useful
without the underlying kernel module. The cornercase of only generating
keys and not using the secure tunnel is something that won't be done on
an embedded OpenWrt system often. On the other hand, maintaining a
separate meta-package only for this use case introduces extra
complexity. WireGuard changes for Linux 5.10 remove the meta-package.
So let's make wireguard-tools depend on kmod-wireguard
to make WireGuard easier to use without having to install multiple
packages.
Fixes: ea980fb9 ("wireguard: bump to 20191226")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Use NETWORK_SUPPORT_MENU like all other modules in netsupport.mk. Drop
SECTION and CATEGORY fields as they are set by default and to match
other packages in netsupport.mk. Use better TITLE for kmod-wireguard
(taken from upstream drivers/net/Kconfig).
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
On Linux 5.4, build WireGuard from backports. Linux 5.10 contains
wireguard in-tree.
Add in-kernel crypto libraries required by WireGuard along with
arch-specific optimizations.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
ZTE MF283+ is a dual-antenna LTE category 4 router, based on Ralink
RT3352 SoC, and built-in ZTE P685M PCIe MiniCard LTE modem.
Hardware highlighs:
- CPU: MIPS24KEc at 400MHz,
- RAM: 64MB DDR2,
- Flash: 16MB SPI,
- Ethernet: 4 10/100M port switch with VLAN support,
- Wireless: Dual-stream 802.11n (RT2860), with two internal antennas,
- WWAN: Built-in ZTE P685M modem, with two internal antennas and two
switching SMA connectors for external antennas,
- FXS: Single ATA, with two connectors marked PHONE1 and PHONE2,
internally wired in parallel by 0-Ohm resistors, handled entirely by
internal WWAN modem.
- USB: internal miniPCIe slot for modem,
unpopulated USB A connector on PCB.
- SIM slot for the WWAN modem.
- UART connector for the console (unpopulated) at 3.3V,
pinout: 1: VCC, 2: TXD, 3: RXD, 4: GND,
settings: 57600-8-N-1.
- LEDs: Power (fixed), WLAN, WWAN (RGB),
phone (bicolor, controlled by modem), Signal,
4 link/act LEDs for LAN1-4.
- Buttons: WPS, reset.
Installation:
As the modem is, for most of the time, provided by carriers, there is no
possibility to flash through web interface, only built-in FOTA update
and TFTP recovery are supported.
There are two installation methods:
(1) Using serial console and initramfs-kernel - recommended, as it
allows you to back up original firmware, or
(2) Using TFTP recovery - does not require disassembly.
(1) Using serial console:
To install OpenWrt, one needs to disassemble the
router and flash it via TFTP by using serial console:
- Locate unpopulated 4-pin header on the top of the board, near buttons.
- Connect UART adapter to the connector. Use 3.3V voltage level only,
omit VCC connection. Pin 1 (VCC) is marked by square pad.
- Put your initramfs-kernel image in TFTP server directory.
- Power-up the device.
- Press "1" to load initramfs image to RAM.
- Enter IP address chosen for the device (defaults to 192.168.0.1).
- Enter TFTP server IP address (defaults to 192.168.0.22).
- Enter image filename as put inside TFTP server - something short,
like firmware.bin is recommended.
- Hit enter to load the image. U-boot will store above values in
persistent environment for next installation.
- If you ever might want to return to vendor firmware,
BACK UP CONTENTS OF YOUR FLASH NOW.
For this router, commonly used by mobile networks,
plain vendor images are not officially available.
To do so, copy contents of each /dev/mtd[0-3], "firmware" - mtd3 being the
most important, and copy them over network to your PC. But in case
anything goes wrong, PLEASE do back up ALL OF THEM.
- From under OpenWrt just booted, load the sysupgrade image to tmpfs,
and execute sysupgrade.
(2) Using TFTP recovery
- Set your host IP to 192.168.0.22 - for example using:
sudo ip addr add 192.168.0.22/24 dev <interface>
- Set up a TFTP server on your machine
- Put the sysupgrade image in TFTP server root named as 'root_uImage'
(no quotes), for example using tftpd:
cp openwrt-ramips-rt305x-zte_mf283plus-squashfs-sysupgrade.bin /srv/tftp/root_uImage
- Power on the router holding BOTH Reset and WPS buttons held for around
5 seconds, until after WWAN and Signal LEDs blink.
- Wait for OpenWrt to start booting up, this should take around a
minute.
Return to original firmware:
Here, again there are two possibilities are possible, just like for
installation:
(1) Using initramfs-kernel image and serial console
(2) Using TFTP recovery
(1) Using initramfs-kernel image and serial console
- Boot OpenWrt initramfs-kernel image via TFTP the same as for
installation.
- Copy over the backed up "firmware.bin" image of "mtd3" to /tmp/
- Use "mtd write /tmp/firmware.bin /dev/mtd3", where firmware.bin is
your backup taken before OpenWrt installation, and /dev/mtd3 is the
"firmware" partition.
(2) Using TFTP recovery
- Follow the same steps as for installation, but replacing 'root_uImage'
with firmware backup you took during installation, or by vendor
firmware obtained elsewhere.
A few quirks of the device, noted from my instance:
- Wired and wireless MAC addresses written in flash are the same,
despite being in separate locations.
- Power LED is hardwired to 3.3V, so there is no status LED per se, and
WLAN LED is controlled by WLAN driver, so I had to hijack 3G/4G LED
for status - original firmware also does this in bootup.
- FXS subsystem and its LED is controlled by the
modem, so it work independently of OpenWrt.
Tested to work even before OpenWrt booted.
I managed to open up modem's shell via ADB,
and found from its kernel logs, that FXS and its LED is indeed controlled
by modem.
- While finding LEDs, I had no GPL source drop from ZTE, so I had to probe for
each and every one of them manually, so this might not be complete -
it looks like bicolor LED is used for FXS, possibly to support
dual-ported variant in other device sharing the PCB.
- Flash performance is very low, despite enabling 50MHz clock and fast
read command, due to using 4k sectors throughout the target. I decided
to keep it at the moment, to avoid breaking existing devices - I
identified one potentially affected, should this be limited to under
4MB of Flash. The difference between sysupgrade durations is whopping
3min vs 8min, so this is worth pursuing.
In vendor firmware, WWAN LED behaviour is as follows, citing the manual:
- red - no registration,
- green - 3G,
- blue - 4G.
Blinking indicates activity, so netdev trigger mapped from wwan0 to blue:wwan
looks reasonable at the moment, for full replacement, a script similar to
"rssileds" would need to be developed.
Behaviour of "Signal LED" in vendor firmware is as follows:
- Off - no signal,
- Blinking - poor coverage
- Solid - good coverage.
A few more details on the built-in LTE modem:
Modem is not fully supported upstream in Linux - only two CDC ports
(DIAG and one for QMI) probe. I sent patches upstream to add required device
IDs for full support.
The mapping of USB functions is as follows:
- CDC (QCDM) - dedicated to comunicating with proprietary Qualcomm tools.
- CDC (PCUI) - not supported by upstream 'option' driver yet. Patch
submitted upstream.
- CDC (Modem) - Exactly the same as above
- QMI - A patch is sent upstream to add device ID, with that in place,
uqmi did connect successfully, once I selected correct PDP context
type for my SIM (IPv4-only, not default IPv4v6).
- ADB - self-explanatory, one can access the ADB shell with a device ID
added to 51-android.rules like so:
SUBSYSTEM!="usb", GOTO="android_usb_rules_end"
LABEL="android_usb_rules_begin"
SUBSYSTEM=="usb", ATTR{idVendor}=="19d2", ATTR{idProduct}=="1275", ENV{adb_user}="yes"
ENV{adb_user}=="yes", MODE="0660", GROUP="plugdev", TAG+="uaccess"
LABEL="android_usb_rules_end"
While not really needed in OpenWrt, it might come useful if one decides to
move the modem to their PC to hack it further, insides seem to be pretty
interesting. ADB also works well from within OpenWrt without that. O
course it isn't needed for normal operation, so I left it out of
DEVICE_PACKAGES.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove kmod-usb-ledtrig-usbport, take merged upstream patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As PKG_LICENSE is originally set by include/trusted-firmware-a.mk it
can only be appended after that. Hence move that line below the
include to actually make sense.
(cosmetical change, already slipped into openwrt-21.02 branch)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This package had two patches (with two headers etc.) in one file,
which would have quilt merging them during a refresh.
Separate these patches into two files, as the original intent seems
to be having them separate.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When using Shell arithmetric evaluation via $((..)) the variables in
the expression do not need to be prefixed by the '$' sign.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Check if firmware environment variable 'rootfs_data_max' exists and is
set to a numerical value greater than 0. If so, limit rootfs_data
volume to that size instead of using the maximum available size.
This is useful on devices with lots of flash where users may want to
have eg. a volume for persistent logs and statistics or for external
applications/containers. Persistence on rootfs overlay is limited by
the size of memory available during the sysugprade process as that
data needs to be copied to RAM while the volume is being recreated
during sysupgrade. Hence it is unsuitable for keeping larger amounts
of data accross upgrade which makes additional volume(s) for
application data desirable.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow for single (external-data) FIT image to hold kernel, dtb and
squashfs. In that way, the bootloader verifies the system integrity
including the rootfs, because what's the point of checking that the
hash of the kernel is correct if it won't boot in case of squashfs
being corrupted? Better allow bootloader to check everything needed
to make it at least up to failsafe mode. As a positive side effect
this change also makes the sysupgrade process on nand potentially
much easier as it is now.
In short: mkimage has a parameter '-E' which allows generating FIT
images with 'external' data rather than embedding the data into the
device-tree blob itself. In this way, the FIT structure itself remains
small and can be parsed easily (rather than having to page around
megabytes of image content). This patch makes use of that and adds
support for adding sub-images of type 'filesystem' which are used to
store the squashfs. Now U-Boot can verify the whole OS and the new
partition parsers added in the Linux kernel can detect the filesystem
sub-images, create partitions for them, and select the active rootfs
volume based on the configuration in FIT (passing configuration via
device tree could be implemented easily at a later stage).
This new FIT partition parser works for NOR flash (on top of mtdblock),
NAND flash (on top of ubiblock) as well as classic block devices
(ie. eMMC, SDcard, SATA, NVME, ...).
It could even be used to mount such FIT images via `losetup -P` on a
user PC if this patch gets included in Linux upstream one day ;)
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Upstream integrated multiple patches from Distributions and did other
changes:
* rp-pppoe.so was renamed to pppoe.so
* Converted to ANSI C
The following patches were applied upstream:
* 100-debian_ip-ip_option.patch
* 101-debian_close_dev_ppp.patch
* 103-debian_fix_link_pidfile.patch
* 106-debian_stripMSdomain.patch
* 107-debian_pppoatm_wildcard.patch
* 110-debian_defaultroute.patch
* 202-no_strip.patch
Compilation with musl libc was fixed upstream so
140-pppoe_compile_fix.patch is not needed any more
Parts of the 203-opt_flags.patch patch were applied in a different way
upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The packages feed has a proposed package for a GOST engine, which needs
support from the main openssl library. It is a default option in
OpenSSL. All that needs to be done here is to not disable it.
Package increases by a net 1-byte, so it is not really really worth
keeping this optional.
This commit also includes a commented-out example engine configuration
in openssl.cnf, as it is done for other available engines.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This adds the necessary nuts and bolts for the uboot settings for both the ZyXEL GS1900-8HP v1 and v2.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Biggest fix for this version is CVE-2021-3336, which has already been
applied here. There are a couple of low severity security bug fixes as
well.
Three patches are no longer needed, and were removed; the one remaining
was refreshed.
This tool shows no ABI changes:
https://abi-laboratory.pro/index.php?view=objects_report&l=wolfssl&v1=4.6.0&v2=4.7.0
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
There are efforts underway to bring wireguard in-tree for Linux 5.4 and
to have a common build infrastructure for both 5.4 and 5.10 for
kmod-wireguard[0]. Until then, restrict kmod-wireguard to build only on
Linux 5.4, because the wireguard-compat package will not build on Linux
5.10.
[0]: https://github.com/openwrt/openwrt/pull/3885
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Modify existing modules to reflect their new location in Linux 5.10. Add
missing dependenices.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
[enable CRYPTO_USER_API_ENABLE_OBSOLETE; add kmod-crypto-hash dependency
to usb-net-rtl8152]
Signed-off-by: David Bauer <mail@david-bauer.net>
Now that mirrors have picked it up, switch to using the @OPENWRT
mirror instead of hosting those files on Github.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
