When r42245 moved A4001N to DT based detection the image padding size
was accidentally increased from 4 to 8 MiB. This made images unflashable
on these devices.
Fixes#19836.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45945
Livebox does need the uncompressed kernel, so just create it during
image generation.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45875
Delete the dtb appended, uncompressed kernels after having compressed
them, so they don't end in the image builder.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45869
Add it to the appropriate places so the power led properly works
and ethernet is properly configured for failsafe.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45709
This patch adds support for the Huawei HG655b.
Nothing much special in this router, it's just another BCM6368 with
a Ralink RT3062 wifi chip and the calibration data embedded in the
main flash chip at offset 0x7c0000. There is also configuration data
used by the OEM firmware before the cal_data partition, this area is
protected by the board_data partition in this patch.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45708
This was a remnant of an old version.
Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45583
This should rather be done by passing appropriate platform_data/OF, but
should suffice for now.
Fixes e.g. GbE ports on BCM963268BU_P300.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45505
At least the third rgmii port is available on 63169, so assume all are
available. Simplifies cpu vs. variant handling.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45504
Accidentally left over development artifact.
Reported-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45179
Now that all supported boards have an dts there is no need for a
dtb free kernel anymore.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45169
Appearently the kernel only uses kernel above it, so moving it to an
higher address causes a lot of unavailable memory (#19327).
Also move the on-flash kernel to 0x80a0000, as newer CFEs don't like
uncompressing there (net-booting an ELF kernel is fine, though).
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45164
Should fix pcmcia on BCM6348 and BCM6358 after switching to DT-probed
gpio controllers.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44995
Fixes the following issue:
drivers/gpio/gpio-bcm63xx.c: In function 'bcm63xx_gpio_probe':
drivers/gpio/gpio-bcm63xx.c:80:4: error: implicit declaration of function 'devm_kasprintf' [-Werror=implicit-function-declaration]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44986
Support for the BT HomeHub 2.0 Type A.
This router was manufactured by Thomson, and it's BCM6358 based.
The leds are controled by two chained HC594, all working ok. The BCM5325
switch has the RESET# pin wired to the GPIO15, but currently there is no
way to tell the b53 driver how to get this gpio number in brcm63xx,
therefore swconfig won't use it when performing a switch reset.
The patch was tested with several firmwares, and all except unsupported
stuff (i.e xDSL) works pretty well.
Tested-by: Tahir <tahir00ali@gmail.com>
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
SVN-Revision: 44985
Currently there isn't images ready for flashing liveboxes boards. This
patch adds a script and the code to call it in the bcm63xx images
builder makefile to generate the livebox 1 firmware.
I removed some lines to avoid generating unneded files in the bin/ dir
for this board. And added code to generate a squashed rootfs aligned to
64 kB since the current one in the /bin dir is 128 kB aligned and
doesn't work. Still no sysupgrade support for this board. Upgrading from
within openwrt can be done writing with mtd the kernel, and then the 64k
aligned rootfs.
Regards
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: use sed instead of a separate shell script for the boot script, make it
respect the load address]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44982
Ensure gpio chips are always labeled the same; this allows simplifying
any arch setup gpio lookups.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44846
Now that we have converted all users of global variables to use
brcm63xx_board_name, we can savely convert the implicit call to detect
in brcm63xx.sh to a single, explicit call in preinit.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44840
r37000 made button kmods loaded from generic code, so we don't use
it anymore for deciding to load them.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44838
Instead of setting them up on invocation of brcm63xx_detect, set them
when calling diag.sh based.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44837
Board IDs are not unique, so in preparation for depricating them, always
use board_name for any (default) configuration decisions.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44836
