Without patch unloading the dwc3-of-simple module went stuck after
successfully removing hcd.1 during the hcd.0 removal:
root@LEDE:/# rmmod dwc3-of-simple
[ 21.391846] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 21.391931] usb usb4: USB disconnect, device number 1
[ 21.397038] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 21.401111] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 21.406685] usb usb3: USB disconnect, device number 1
[ 21.412848] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 21.417248] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 21.422521] usb usb2: USB disconnect, device number 1
followed by nothing.
Sometimes a stall CPU was detected, or a kernel panic,
or a reboot occurred after a couple of minutes.
At the same time unloading the dwc3 module followed by dwc3-of-simple
module was working repeatedly.
root@LEDE:/# rmmod dwc3
[ 53.827328] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 53.827412] usb usb4: USB disconnect, device number 1
[ 53.832630] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 53.836452] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 53.842314] usb usb3: USB disconnect, device number 1
[ 53.848412] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 53.852542] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 53.857882] usb usb2: USB disconnect, device number 1
[ 53.863956] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 53.867875] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 53.873696] usb usb1: USB disconnect, device number 1
[ 53.879742] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/# rmmod dwc3-of-simple
root@LEDE:/#
For the non-working case, the code was stuck in a readl() in
http://lxr.free-electrons.com/source/drivers/usb/host/xhci.c#L91
because
http://lxr.free-electrons.com/source/drivers/usb/dwc3/dwc3-of-simple.c#L126
was disabling the wrong clocks when removing hcd.1 (it was disabling
the clock of hcd.0). That's why the readl() went stuck when removing
hcd.0
The patch however addresses the clock assignment from the Netgear R7500
dts file and backs off the previous attempt.
Now unloading and repeated module loading is working just fine.
root@LEDE:/# rmmod dwc3-of-simple
[ 24.089679] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 24.089765] usb usb4: USB disconnect, device number 1
[ 24.094856] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 24.098963] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 24.104522] usb usb3: USB disconnect, device number 1
[ 24.111194] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 24.115086] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 24.120396] usb usb2: USB disconnect, device number 1
[ 24.126503] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 24.130347] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 24.135948] usb usb1: USB disconnect, device number 1
[ 24.142085] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/#
Fixes: dwc3-of-simple module unloading for Netgear R7500
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
The patch follows the qualcomm code comments setting
SSUSB_CTRL_TEST_POWERDOWN to 0x1 and is testing and clearing the
bit during USB superspeed PHY init. According to Andy Gross it
needs to be BIT(26).
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes Ethernet<->WiFi bridge for Raspberry Pi and probably other devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Original armvirt target is now subtarget 32. Other than that the built
result should remain the same as before
Besides old features already available with arm64, the new armvirt/64
subtarget will also have those features originally enabled for
armvirt/32 with commit 44ecfc2 ("armvirt: new target")
- pl011, uart
- pl031, rtc
- pl061, gpio
- pci-host-generic
- virtio_{mmio,pci,net,blk,scsi,9p,console,balloon}
- smp with NR_CPUS=4
- cpu-hotplug
- ext4
- DEBUG_BUGVERBOSE for debug purposes
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Fix a '==' that should be a '=' in a test condition. Busybox fortunately
doesn't care.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Add red:internet led on gpio 30 previously claimed as missing.
Wifi led was claimed as blue however there are no blue leds on the
board at all. Actually there are two wifi leds, green & amber so add
definitions for those. Make the newly discovered green wifi led gpio
14 the default.
There is no amber power led on this board. The mention of the amber
power led in the manual means power red and power green at the same
time.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
[removed unnecessary aliases, add migration script]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use fixed led names and add each board variant instead of manipulating
the board name.
It makes the ramips board name function less different to the one used
in other targets and allows to merge them with a common function.
Signed-off-by: Mathias Kresin <dev@kresin.me>
We need to keep the former used (unmodified) boardname in the metadata.
Otherwise an upgrade from an board using the old boardname will be
refused.
Fixes: a75ce960ac ("ramips: use different board names for variants")
Signed-off-by: Mathias Kresin <dev@kresin.me>
PSG1218 got only 4 Ethernet ports and WAN on port 3 while
PSG1218K2C got 5 Ethernet ports and WAN on port 4
Switch to use kmod-kt76x2 instead of kmod-mt76 for both devices while
at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use the stateless 4-byte op codes for this flash chip to fix reboot
hangs on SoCs expecting the flash chip in 3-byte mode.
Fixes: FS#179
Signed-off-by: Mathias Kresin <dev@kresin.me>
This reverts commit 51397d7d95.
There are some unresolved random crashes on WRT1900AC v1 that still need
to be sorted out
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes:
Thermal sensors on bcm2835 SoC (BCM2835_THERMAL) [N/m/y/?] (NEW) aborted!
This symbol depends on ARCH_BCM2835 so it should be OK to disable it at
brcm2708 target only.
Fixes: 7d32caa61fb0 ("brcm2708: backport upstream sdhost controller driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Since 192f0a3db8 ("ath9k: unset the default LED pin if used by
platform leds") the default ath9k wireless LED is not set as soon as
any pin of the ath ath9k gpio controller is used.
All touched boards have leds defined which are using the gpio pins
exposed by the ath9k driver but rely on a default set wireless led
trigger.
Add the wireless leds were missing and setup the wireless phy trigger
in userspace.
Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Netgear R6220 requires the kmod-usb3 package and misses
kmod-usb-ledtrig-usbport package to setup the configured usb led
trigger.
Drop the already target selected kmod-mt76.
Fixes: FS#686
Fixes: 38bee61dab ("ramips: add support for Netgear R6220")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fix the PCIe 5GHz wireless by using the on flash eeprom/caldata.
Disable the 2.4GHz band as this band has no antennas attached but is
enabled in the eeprom/caldata.
Fixes: FS#691
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fix the PCIe 5GHz wireless by using the ralink mtd-eeprom property as
this board have a RT5592 and uses the rt2x00 driver. The mediathek
device tree bindings do not work here.
Fixes: FS#691
Fixes: d8dd207ea6 ("ramips: use the ralink,mtd-eeprom device tree property")
Signed-off-by: Mathias Kresin <dev@kresin.me>
The factory image has an uImage header covering the entire image and
not only the kernel. The original uImage header which covers only the
kernel is appended to the end of the image.
During LEDE boot the uImage rootfs splitter skips the whole filesystem,
can't find a valid filesystem magic and panics.
The last known working version was OpenWrt 14.07, which simply kept on
searching for an uImage header if the first found didn't resulted into
a working rootfs. This behaviour is kind of error prone since it could
produce false positives.
Since the sysupgrade image works fine in combination with the tftp
recovery for doing the initial installation of LEDE, simply drop the
factory image.
Related: FS#462
Signed-off-by: Mathias Kresin <dev@kresin.me>
The original implementation loaded the count register with (wrong) semi-
random values due to its implemenation nature.
If the wrongly calulated value was below the kickrate,
the WD was triggered and rebooted the system.
Rework this, partly based on upstream patches, to dynamically fetch the
current clockrate and calculate the proper offset for the WD countdown
register.
Before:
[ 143.800000] count val: 27219720
[ 148.820000] count val: 50623201
[ 153.830000] count val: 96425250
[ 158.830000] count val: 89735401
[ 163.840000] count val: 4756110
After:
[ 0.700000] MPCore WD init. clockrate: 299984500 prescaler: 256
countrate: 1171814 timeout: 60s
[ 358.530000] count val: 35154751
[ 363.540000] count val: 35154750
[ 368.540000] count val: 35154751
[ 373.550000] count val: 35154750
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
In preparation for bumping arm64 to 4.9, add a bunch of configuration
symbols that are available under arm64.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Drop sample command line to use against the ARM Foundation v8 model and
replace the path to something that matches LEDE's directory structure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This required us to both download the Foundation emulator but also build
a boot wrapper. QEMU is now fully usable and is a much better
replacement.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Instead of renaming the default wireless led attached to the wireless
chip, add a new led using the platform leds with the phy0tpt trigger
set in userspace.
When switching ar71xx to device tree, the same can be done by using the
build in GPIO controller and without adding new bindings.
Drop the now unused platform code.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With the fritz-tools a userspace parser for the Tiny Flash File System
is available and makes the tffs2 kernel patches obsolete.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Split the fritz-tools into subpackages. fritz_tffs_read is usefull for
all Fritz boards where fritz-cal_extract is only required for the
Fritz 4040 at the moment.
Rename the tffs related binary to the more catchy name fritz_tffs and
move the whole package to utilities since the package doesn't really
provide a firmware file.
Make the fritz-tools available for all targets and build them shared.
The tffs is used by avm on lantiq and ar71xx as well.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fix the list order instead of adjusting the controller scan order.
Revert the former required changes to the lantiq PCIe driver.
Signed-off-by: Mathias Kresin <dev@kresin.me>
* adds MT7530 DSA support
* backport latest ethernet driver
* add PMIC leds
* add auxadc support
* add efuse support
* add thermal sensor support
* add irq affinity support for ethernet
still todo
* DSA multi cpu support
Signed-off-by: John Crispin <john@phrozen.org>
Keeping it in base-files was resulting in adding it to the base-files
package. This file is meant to be included manually for initramfs
images only.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
There are currently several supported TP-Link devices without specified
version number in image name and/or DEVICE_TITLE (e.g. WBS210, WBS510,
TL-WR810N, TL-WA7510N, TL-WPA8630), but vendor website shows that there
are already more than one version of them on the market.
For devices like Archer C5, which second version is based on a total
different platform, missing version number in DEVICE_TITLE (used in
menuconfig) might be misleading for users.
To make it less confusing for users and easier to maintain in future,
include version number in image name and DEVICE_TITLE for all TP-Link
devices, even if there is only one version of device at the moment.
Also, keep DEVICE_TITLE in same format for all TP-Link devices.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Acked-by: John Crispin <john@phrozen.org>
Kernel/hardware support for this board has been implemented since
Chaos Calmer. This set of patches is to get the board identified in
userland. This will allow support for things like sysupgrade,
configuring initial LED state, configuring initial switch state, etc.
Signed-off-by: Ron Angeles <ronangeles@gmail.com>
This router has the same hardware as TP-LINK TL-WR841N/ND v11 (same FCC
ID, same TFTP image name...).
If the stock firmware web interface doesn't accept LEDE factory image,
it can be flashed via the U-Boot TFTP recovery mode, by long-pressing
the reset button after power on.
The TFTP image name is wr841nv11_tp_recovery.bin (yes, v11, not v12).
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
On the more sophisticated (i.e. deeper FIFO) serial controllers,
flow-control might be needed to avoid dropping output.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
