Commit Graph

417 Commits

Author SHA1 Message Date
Alberto Bursi
4de0a61a62 kirkwood: enable sata port multiplier
Marvell sata controllers in all kirkwood SoCs support
sata port multipliers, just like mvebu.
Enable this feature in the default kernel config
so it is available in normal builds.
tested and working on nsa310b

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2019-05-11 16:37:11 +02:00
Felix Fietkau
85017c40f4 build: add a config option for enabling a testing version of the target kernel
If the target supports a newer kernel version that is not used by default
yet, it can be enabled with this option

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-05-11 11:37:10 +02:00
Koen Vandeputte
af6c86dbe5 kernel: bump 4.14 to 4.14.108
Refreshed all patches.

Altered patches:
- 950-0033-i2c-bcm2835-Add-debug-support.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-27 10:48:59 +01:00
Koen Vandeputte
d9ab3240a5 kernel: bump 4.19 to 4.19.24
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-22 10:53:42 +01:00
Paul Wassi
d42c9ce326 kirkwood: add kernel 4.19 support
Add patches for 4.19
Drop patch 200-disable-tso, as the packet corruption was fixed in
kernel commit 3b89624ab54b9dc2d92fc08ce2670e5f19ad8ec8

Restructure the DTS for Marvell switch in 104-ea3500 and 105-ea4500
to fix DTC warning.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-17 19:22:39 +01:00
Mathias Kresin
80c61c161a treewide: use wpad-basic for not small flash targets
Add out of the box support for 802.11r and 802.11w to all targets not
suffering from small flash.

Signed-off-by: Mathias Kresin <dev@kresin.me>

Mathias did all the heavy lifting on this, but I'm the one who should
get shouted at for committing.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-10-16 15:07:41 +01:00
Felix Fietkau
f445953d9f kirkwood: remove linux 4.9 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-09-29 18:09:45 +02:00
Koen Vandeputte
fec8fe8069 kernel: bump 4.9 to 4.9.116
Refreshed all patches

Remove upstreamed patches.
- 103-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch
- 001-4.11-01-mtd-m25p80-consider-max-message-size-in-m25p80_read.patch
- 001-4.15-08-bcm63xx_enet-correct-clock-usage.patch
- 001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch
- 900-gen_stats-fix-netlink-stats-padding.patch

Introduce a new backported patch to address ext4 breakage, introduced in 4.9.112
- backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch

This patch has been slightly altered to compensate for a new helper function
introduced in later kernels.

Also add ARM64_SSBD symbol to ARM64 targets still running kernel 4.9

Compile-tested on: ar71xx, bcm2710
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-01 09:46:59 +02:00
Stijn Tintel
22b9f99b87 kernel: bump 4.14 to 4.14.59
Drop patch that was superseded upstream:
ramips/0036-mtd-fix-cfi-cmdset-0002-erase-status-check.patch

Drop upstreamed patches:
- apm821xx/020-0001-crypto-crypto4xx-remove-bad-list_del.patch
- apm821xx/020-0011-crypto-crypto4xx-fix-crypto4xx_build_pdr-crypto4xx_b.patch
- ath79/0011-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch
- brcm63xx/001-4.15-08-bcm63xx_enet-correct-clock-usage.patch
- brcm63xx/001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch
- generic/backport/080-net-convert-sock.sk_wmem_alloc-from-atomic_t-to-refc.patch
- generic/pending/170-usb-dwc2-Fix-DMA-alignment-to-start-at-allocated-boun.patch
- generic/pending/900-gen_stats-fix-netlink-stats-padding.patch

In 4.14.55, a patch was introduced that breaks ext4 images in some
cases. The newly introduced patch
backport-4.14/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch
addresses this breakage.

Fixes the following CVEs:
- CVE-2018-10876
- CVE-2018-10877
- CVE-2018-10879
- CVE-2018-10880
- CVE-2018-10881
- CVE-2018-10882
- CVE-2018-10883

Compile-tested: ath79, octeon, x86/64
Runtime-tested: ath79, octeon, x86/64

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-07-31 05:11:07 +03:00
Ademar Arvati Filho
27b2f0fc0f kirkwood: add support for Iomega Storcenter ix2-200
Iomega Storcenter ix2-200 is a dual SATA NAS powered by a Marvell
 Kirkwood SoC clocked at 1GHz. It has 256MB of RAM and 32MB of
 flash memory, 3x USB 2.0 and 1x 1Gbit/s NIC

Specification:
- SoC: Marvell Kirkwood 88F6281
- CPU/Speed: 1000Mhz
- Flash-Chip: Hynix NAND
- Flash size: 32 MiB,erase size:16 KiB,page size:512,OOB size:16
- RAM: 256MB
- LAN: 1x 1000 Mbps Ethernet
- WiFi: none
- 3x USB 2.0
- UART: for serial console

Installation instructions - easy steps:
1. download factory.bin and copy into tftp server
2. access uboot environment with serial cable and run
    ```
    setenv mainlineLinux yes
    setenv arcNumber 1682
    setenv console 'console=ttyS0,115200n8'
    setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
    setenv bootargs_root 'root='
    setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
    saveenv
    setenv serverip 192.168.1.1
    setenv ipaddr 192.168.1.13
    tftpboot 0x00800000 factory.bin
    nand erase 0x100000 $(filesize)
    nand write 0x00800000 0x100000 $(filesize)
    run bootcmd
    ```
3. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)

Installation steps nand bad blocks proof:
1. download initramfs-uImage and copy into usb ext2 partition
    ```
    mkfs.ext2 -L ext2 /dev/sdh1
    mount -t ext2 /dev/sdh1 /mnt
    cp initramfs-uImage /mnt/initramfs.bin
    umount /mnt
    ```
2. access uboot environment with serial cable and run
    ```
    setenv mainlineLinux yes
    setenv arcNumber 1682
    setenv console 'console=ttyS0,115200n8'
    setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
    setenv bootargs_root 'root='
    setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
    saveenv
    usb reset; ext2load usb 0:1 0x00800000 /initramfs.bin; bootm 0x00800000
    ```
3. log into openwrt and sysupgrade to install into flash
    ```
    sysupgrade -n /tmp/sysupgrade.bin
    ```
4. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)

Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
2018-07-30 15:21:00 +02:00
Sergey Ryazanov
67a3cdcbb0 kernel: enable THIN_ARCHIVES by default
THIN_ARCHIVES option is enabled by default in the kernel configuration
and no one target config disables it. So enable it by default and remove
this symbol from target specific configs to keep them light.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:55:20 +02:00
Sergey Ryazanov
bdc2b58c4b kernel: enable FUTEX_PI by default
New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols
are enabled. Both of these symbols are enabled by default in the
generic config, so enable FUTEX_PI by default too to keep platform
specific configs minimal.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:55:12 +02:00
Sergey Ryazanov
a08b0d0c31 kernel: enable EXPORTFS by default
OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have
OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config
of 4.14 and remove this option from platform specific configs.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:55:05 +02:00
Sergey Ryazanov
978543a246 kernel: disable DRM_LIB_RANDOM by default
DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST
which is disable by default, so disable DRM_LIB_RANDOM by default too.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:54:57 +02:00
Sergey Ryazanov
ead26e9db6 kernel: disable DMA_{NOOP|VIRT}_OPS by default
These options do not used by any supported arch, so disable them by
default to make arch configs a bit more clean.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:54:49 +02:00
Sergey Ryazanov
f928c338ad kernel: disable ARCH_WANTS_THP_SWAP by default
Only one arch (x86_64) enables this option. So disable
ARCH_WANTS_THP_SWAP by default and remove referencies to it from all
configs (except x86_64) to make them clean.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:54:42 +02:00
Alberto Bursi
e09d4c850d kirkwood: support for buttons in Audi and Viper
Both these devices have a wps and a reset button on
GPIO pins, which need kmod-gpio-button-hotplug
package to work.

Add this package to their default package config.

Troubleshooted and tested on a Viper.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2018-05-15 06:39:37 +02:00
Paul Wassi
6fe9277d0c kirkwood: fix initramfs boot warning on iconnect
The chosen dts configuration linux,initrd-* gives an error message
on bootup of kirkwood-iconnect. Since initramfs/initrd is not used
remove these options from the dts.

Reported-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-03-20 21:45:27 +01:00
Paul Wassi
e0d4ad7127 kirkwood: switch to kernel 4.14
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-03-20 21:45:27 +01:00
Paul Wassi
1447784a8c kirkwood: add kernel 4.14 support
Add patches for 4.14, undoing upstream changes for Linksys devices
regarding DSA. Instead, the switchdev driver marvell,88e6171 is used.

Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Tested-by: Alberto Bursi <alberto.bursi@outlook.it>
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-03-20 21:45:27 +01:00
Hauke Mehrtens
bf4aa52dbf kernel: make mtd patches apply again
This makes some of the mtd patches apply again after some generic
patches were changed.
These problems where found by build bot.

Fixes: ac9bcefa3b ("kernel: use V10 of mtd patchset adding support for "compatible" string")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-15 00:42:41 +01:00
Kevin Darbyshire-Bryant
d8565a06dc kernel: bump 4.9 to 4.9.77
Refresh patches.
Remove upstreamed patches:

target/linux/generic/backport-4.9/023-2-smsc75xx-use-skb_cow_head-to-deal-with-cloned-skbs.patch
target/linux/generic/backport-4.9/023-3-cx82310_eth-use-skb_cow_head-to-deal-with-cloned-skb.patch
target/linux/generic/backport-4.9/023-4-sr9700-use-skb_cow_head-to-deal-with-cloned-skbs.patch
target/linux/generic/backport-4.9/023-5-lan78xx-use-skb_cow_head-to-deal-with-cloned-skbs.patch

CVEs completely or partially addressed:

CVE-2017-5715
CVE-2017-5753
CVE-2017-17741
CVE-2017-1000410

Compile-tested: ar71xx Archer C7 v2
Run-tested: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-20 20:22:01 +01:00
尤晓杰
a7e62b4be1 kirkwood: fix sysupgrade
The platform_check_image() stub need to return 0 for success, otherwise
the sysupgrade will fail with:

  Image check 'platform_check_image' failed.

Fixes: aa6f5f1787 ("kirkwood: use image metadata")
Signed-off-by: 尤晓杰 <yxj790222@163.com>
[reworded commit message}
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-18 07:26:28 +01:00
Mathias Kresin
0674a99f7e kirkwood: sort occurrences of boardame alphabetically
This restores the alphabetical sort that was present
before the renaming of boardname.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:55 +01:00
Alberto Bursi
c19f811c4d kirkwood: add pogoplug v4
also known as
POGO-V4-A3-02
or
POGO-V4-A3-01

SoC: Marvell 88F6192 800Mhz
SDRAM memory: 128MB
Gigabit ethernet: 1 Marvell 88E1310
Flash memory: 128MB
2 status LEDs (one green one red)
1 "Eject" button on the back (used as "Reset" button)
1 USB 2.0 port (on upper side)
1 sata slot (power + data) for 2.5'' drives (upper side)
2 USB 3.0 ports from a controller on PCIe x1 of the SoC
1 full-size SDcard slot (fits a whole SD card into it)

This device supports the (linux-only) kwboot tool to send
a new uboot over serial console, so it is easy to unbrick
in case the uboot is erased and the device won't boot.

-----
Install instructions:
-----
Since it's not possible to get ssh access to these
devices, the only way to take control is to
solder pins to get TTL serial access.

Case can be opened by removing screws beneath two rubber
feet at back of device, then lifting while prying the
sides of the upper part out to unhook a latch on each
side about 2/3rds of the way toward the front.

Serial connection pins are those labeled "J11", left
of SD as you face SD opening.
Pins are (from left to right, i.e. the first in the list
is the nearest to the SD slot) GND, Rx, Tx.
Do not connect +V pin if you use a USB (self-powered)
TTL-to-USB dongle. Any USB TTL-to-USB converter will work.
Baud rate is 115200, parity "none", databits "8",
flow control "none".

Stock uboot is unable to read ubi partitions (nor usb)
so we will replace it first with our uboot.

Start a TFTP server at IP address 169.254.254.254, and
place the uboot.kwb file in the folder of the server.

Start the serial session and then power up the device.

As soon as you see text on the serial start pressing random
letter keys to stop the boot process.

If you see something like the following line you can proceed:

CE>>

Otherwise if text is still scrolling by you missed the
opportunity, pull the plug and try again.

write

printenv ethaddr

The uboot will write something like this:

ethaddr=00:50:43:00:02:02

This is the device's MAC address, also present in the sticker
under the device.

Write this down as we will need to add it in the
new uboot configuration.

Use the following commands to load the new uboot:

tftp 0x20000 u-boot.kwb

If the uboot confirms that the transfer was successful,
then you can write it to flash with the following commands:

nand erase 0 0x200000
nand write 0x20000 0 0x1c0000

if after the last command the uboot wrote
"xxxx bytes written: OK"
then it was written correctly and we can proceed.

If it did not go well, try again or ask assistence in forums.
Shutting down or rebooting at this time will brick
the device, to unbrick it you will need to use the kwboot
tool from a Linux PC or Virtual Machine.

Now write:

reset

and press enter, the device will reboot and you should see
again text scrolling by.
Press a random key to stop it, and now you should see

pogoplugv4>

We now add the MAC address back, write:

setenv ethaddr '00:50:43:00:02:02'

Confirm that the uboot has understood by writing

printenv ethaddr

If all looks ok, save the setting with

saveenv

At this point the uboot is configured, and we only need to load
the firmware in the flash memory.

Follow the steps below in "Firmware recovery procedure".

----
Firmware recovery procedure
----
The new uboot allows easy recovery from a bad firmware upgrade
where you can't access the device anymore over ssh or luci.

Take a USB flash drive formatted as FAT32, and copy the
initramfs image file in it (it will have "initramfs" in the
file name), then rename it as "initramfs.bin".

Insert the USB drive in the USB 2.0 port of the pogoplug
(the port at the top).

Power up the device, and wait for it to finish booting.

The uboot should find and load the "initramfs.bin"
from usb and if you are connected with serial you should
see the linux kernel boot log (text scrolling by).
Once it is done, press Enter and you will be greeted by
the OpenWRT banner.

If you were not connected with serial just wait a bit and,
you will be able to access it with ssh or luci web interface
(once you find its IP).

The recovery "initramfs" images are run from RAM, so you will
have to do a normal sysupgrade (firmware upgrade) to write
a firmware image to flash memory.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2018-01-09 22:06:55 +01:00
Mathias Kresin
f5df635ccf kirkwood: sync image filename with boardname
Use <manufacturer>_<modelname> as image name.

Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:55 +01:00
Mathias Kresin
c9e2c35f46 kirkwood: use the generic board detect
Drop the target specific detection function in favour of the generic
one provided by base-files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:55 +01:00
Mathias Kresin
aa6f5f1787 kirkwood: use image metadata
Append and enforce image metadata. Remove the device specific image
checks, they are replaced by image metadata.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:55 +01:00
Mathias Kresin
a10ab9d843 kirkwood: fix nsa310b compatible strings
Use a destinct compatible string fro the nsa310b.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:54 +01:00
Mathias Kresin
18ea058258 kirkwood: fix compatible string in ib62x0 dts
There is no point in being that specifc in a generic dts covering a range
of boards. Keep only the the generic compat string to use it for a
devicetree based boardname.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:54 +01:00
Mathias Kresin
0ebdf0c1d3 kirkwood: drop support for orphaned boards
No image build code for the Guruplug, Sheevaplug and NSA310S exists. Drop
support for the boards for now.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:54 +01:00
Mathias Kresin
d2e18dae28 kirkwood: cleanup image build code
Drop NAND_BLOCKSIZE, UBI_OPTS and UBIFS_OPTS. They are either used by
not supported filesystems or by the legacy image build code.

Add common used options/images to the default build code and override
the options where necessary.

Don't export the kernel image, it isn't required by any board.

While at it, change the file extension for the sysupgrade images to bin.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:06:54 +01:00
Luis Araneda
575178e462 treewide: add only one device when appending to TARGET_DEVICES
This will avoid some conflicts when doing a git rebase or merge,
specially when adding support to a new device.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
[drop brcm47xx changes which rename the images]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-12 18:47:26 +01:00
Mathias Kresin
e0b9ec8e96 treewide: drop target board_name functions
They are not used any longer.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Mathias Kresin
f12a32630f treewide: use the generic board_name function
Use the generic function instead ot the target specific ones.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Mathias Kresin
78cf5eed6e treewide: do board detection during preinit
Do the board detection during preinit to unify it across all targets.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Matthias Schiffer
438dcbfe74
base-files: automatically handle paths and symlinks for RAMFS_COPY_BIN
Depending on busybox applet selection, paths of basic utiilties may differ,
and may not work as symlinks to busybox. Simply using whatever binary is
found in PATH and detecting symlinks automatically is more robust and
easier to maintain.

The list of binaries is also slightly cleaned up and duplicates are
removed.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-07-11 17:26:32 +02:00
Matthias Schiffer
f464da623d
kirkwood: upgrade: fix RAMFS_COPY_*
RAMFS_COPY_* are moved to platform.sh toplevel. The nand_do_upgrade call is
moved to platform_do_upgrade.

Fixes: 30f61a34b4 "base-files: always use staged sysupgrade"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-07-11 17:19:23 +02:00
Mathias Kresin
0825de2df7 kirkwood: drop kernel 4.4 support
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-04 16:29:07 +02:00
Paul Wassi
9808b9ae02 kirkwood: switch to kernel 4.9
Add patches-4.9, some of them (heavily) rewritten:
  - ea4500 is upstream available, keep only LEDE changes in dts
  - ea3500 is changed to match the structure of the upstream ea4500 dts
  - nsa310s rewritten to include the common dtsi
  - nsa325 is dropped, since already upstream

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[refresh kernel config, add on100, use the switchdev based mv88e6171
driver for the linksys boards, keep lede specific rootfs/kernel
partition names for linksys boards, reorder patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-04 16:29:07 +02:00
Stijn Tintel
880f73c327 kernel: cleanup CONFIG_SCHED_HRTICK
Remove CONFIG_SCHED_HRTICK from target configs, as it was added to the
generic config in b47fd76563.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-06-29 04:46:59 +02:00
Makoto Takeuchi
ca27b3d370 kirkwood: add support for Cisco ON100
The Cisco ON100 device is a Kirkwood based router:

    SoC: Marvell 88F6282 1600Mhz
    SDRAM memory: 512MB DDR3 1333Mhz
    Gigabit ethernet: 2x Marvell 88E1310 (over RGMII)
    Flash memory: 512MB
    2 bi-colour status LEDs (green/red)
    1 Reset button
    1 USB 2.0 port (on back)
    1 SDIO slot (on back)

This commit adds a target profile of "Cisco Systems ON100" under the target
system "Marvell Kirkwood".

Flashing can be performed over tftp, once "dhcp" has been issued:
 tftpboot ${loadaddr} lede-kirkwood-on100-squashfs-factory.bin
 nand erase 0x0c0000 ${filesize}
 nand write ${loadaddr} 0x0c0000 ${filesize}

Once flashed, set environment variables to boot:
 setenv bootcmd nand read \${loadaddr} 0x0c0000 0x540000\; setenv bootargs
  \; bootm
 saveenv

Signed-off-by: Makoto Takeuchi <mak0@lxsys.co.uk>
2017-06-12 21:07:31 +02:00
Alberto Bursi
f7fd2abf25 kirkwood: set sata/usb led trigger for NSA3xx
these two devices have a Sata led for each sata port.
These leds must be controlled separately by a special
sata led trigger already used in oxnas target.

Both these devices have a single USB led, and to keep
consistent behaviour with the Sata leds that show
sata activity, this led uses usb-host trigger
to show usb activity.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2017-05-14 21:45:50 +02:00
Alberto Bursi
b52eb549d2 kirkwood: NSA325 remove led triggers from dts
delete useless or unusable default led triggers from dts file.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2017-05-14 21:45:50 +02:00
Alberto Bursi
ff42a8330b kirkwood: fix include in etc/board.d/02_network
the mtd_get_mac_ascii function called within this script requires the inclusion of /lib/functions/system.sh

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2017-02-28 23:46:02 +01:00
Alberto Bursi
4383c13aee kirkwood: add ZyXEL NSA325 device
This patch add ZyXEL NSA325 2-Bay Media Server

The ZyXEL NSA325 device is a Kirkwood based NAS:

- SoC: Marvell 88F6702 1600Mhz
- SDRAM memory: 512MB DDR2 400Mhz
- Gigabit ethernet: Marvell Alaska
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 5 Status LED (green/red)
- 1 Copy/Sync button
- 1 Reset button
- 2 SATA II ports (internal)
- 2 USB 2.0 ports (back)
- 1 USB 3.0 port (front)
- Fan (fixed speed)
- hardware watchdog in a mcu

Basically a bigger, more powerful version of NSA310,
installation is the same as they share the same flash layout.

A notable difference is that there is a hardware watchdog
in a mcu on the board, which is disabled by default in the LEDE u-boot.
The watchdog is also disabled with a GPIO activation through
raw register change when kwbooting or it would reset the board before
the new uboot was transferred.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove dead code]
2017-02-11 21:16:28 +01:00
Alberto Bursi
f99178b6c0 kirkwood: cleanup nsa310b mac address extraction
switch nsa310b mac address reading to mtd_get_mac_ascii helper as
it seems the fw_env.config file is created way later than when
network is set up, when I tested I still had that file included
in the image through /files folder.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2017-02-11 21:16:28 +01:00
Alberto Bursi
94676dd99d kirkwood: add ZyXEL NSA310b
The ZyXEL NSA310 device is a Kirkwood based NAS:

- SoC: Marvell 88F6702 1200Mhz
- SDRAM memory: 256MB DDR2 400Mhz
- Gigabit ethernet: Realtek (over pcie)
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 5 Status LED (green/red)
- 1 Copy/Sync button
- 1 Reset button
- 2 SATA II port (1 internal and 1 external)
- 2 USB 2.0 ports (1 front and 1 back)
- Smart fan

The stock u-boot cannot read ubi so it should be replaced with the
LEDE/OpenWRT's u-boot or with a u-boot from here
https://github.com/mibodhi/u-boot-kirkwood

This device's boot ROM supports "kwboot" tool
(in mainline u-boot, built automatically if CONFIG_KIRKWOOD is declared)
that sends an uboot image to the board over serial connection, it is very easy to unbrick.

The stock bootloader can use usb and read from FAT filesystems,
so the installation process is simple, place the uboot file on a USB flashdrive
formatted as FAT (here it is "openwrt-kirkwood-nsa310.bin", then connect TTL
to the board and write the following commands in the bootloader console:

usb reset
fatload usb 0 0x1000000 openwrt-kirkwood-nsa310.bin
nand write 0x1000000 0x00000 0x100000
reset

Now you are rebooting in the new u-boot, write this in its console to install the firmware:

usb reset
fatload usb 0 0x2000000 lede-kirkwood-nsa310b-squashfs-factory.bin
nand erase.part ubi
nand write 0x2000000 ubi 0x600000

If your firmware file is bigger than 6 MiBs you should write its size in hex
instead of 0x600000 above, or remove that number entirely (it will take a while in this case).

If you are using another uboot that can read ubi, set mtdparts like this

mtdparts=mtdparts=orion_nand:0x00c0000(uboot),0x80000(uboot_env),0x7ec0000(ubi)

And set your bootcmd to be like this

bootcmd=run setenv bootargs; ubi part ubi; ubi read 0x800000 kernel; bootm 0x800000

Then you can install the firmware as described above.

After you installed (or configured) the u-boot for booting the firmware,
write the device's mac address in the ethaddr u-boot env.
The MAC address is usually on a sticker under the device (one of the two codes is the serial),
it should begin with "107BEF" as it is assigned to ZyXEL.

write in the u-boot console (use your MAC address instead of the example)

setenv ethaddr 10:7B:EF:00:00:00
saveenv

to save the mac address in the u-boot.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2017-01-24 16:21:25 +01:00
Felix Fietkau
3be4c6ca93 kirkwood: only add UBI EOF markers for devices that need it
Fixes issues where the second-stage u-boot already uses UBI.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-11 14:04:18 +01:00
Felix Fietkau
018d80007e kernel: remove ubifs xz decompression support
It has been unused, and less useful than squashfs for cases where flash
space usage matters.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-09 14:07:06 +01:00
Hauke Mehrtens
88ca6390ea kernel: bump to 4.4.40
Refresh patches on all 4.4 supported platforms.
Compile & run tested: lantiq/xrx200

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-01-06 19:38:55 +01:00
Felix Fietkau
4731f02fa2 kirkwood: fix ubi partition name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-30 12:58:20 +01:00
Felix Fietkau
83d59453c0 kirkwood: fix sysupgrade for non-dockstar NAND devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-30 12:58:20 +01:00
Felix Fietkau
9c402d03e6 kirkwood: enable initramfs images by default
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-27 12:52:18 +01:00
Felix Fietkau
49e81f9fe4 kirkwood: clean up profiles, move to image makefile
Adds support for per-device rootfs

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-24 09:40:46 +01:00
Felix Fietkau
9a1f441ac8 kirkwood: enable SoC drivers in the kernel config
Clean up packaged modules

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-24 09:40:46 +01:00
Felix Fietkau
44447f6882 kirkwood: clean up FEATURES
Remove dt: it is implicitly enabled based on the kernel config
Remove tar.gz and jffs2_nand: Legacy build code has been removed,
NAND devices are only supported with UBI now.
Remove ubifs: deprecated, use squashfs images instead

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-24 09:40:46 +01:00
Felix Fietkau
2eb1cc3dfc kirkwood: remove legacy image build code
This has been mostly non-functional for a while now

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-24 09:40:46 +01:00
Felix Fietkau
c9e4cf2299 kirkwood: convert iconnect, ib62x0 and pogoplug_e02 to the new image build code
Update the correspoding u-boot configs to stop relying on
kernel-in-rootfs, which was removed a while back

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-12-24 09:40:46 +01:00
Paul Wassi
d2606107ab kirkwood: fix pogo_e02 LED name
The pogo_e02's dts file has its LEDs named "pogo_e02:(...)"
Fix the status-LED's name for this device.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2016-10-26 12:37:46 +02:00
Paul Wassi
f6b5df44d9 kirkwood: remove redundant code in etc/board.d/02_network
Remove redundant code: merge boards/cases that share
the same network configuration.
Also fix the alphabetical ordering of the cases.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2016-10-26 12:37:45 +02:00
Paul Wassi
5528573039 kirkwood: Add RTC driver to kernel for working hctosys
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2016-10-26 09:41:28 +02:00
bobafetthotmail
b9a55277d5 kirkwood: fix uimage creation for some kirkwood devices
because with the current system I'm getting fake uImages that are actually a
renamed zImage, and that's plain wrong.
This fixes bug https://bugs.lede-project.org/index.php?do=details&task_id=131
and https://bugs.lede-project.org/index.php?do=details&task_id=139

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2016-09-19 15:30:32 +02:00
Mathias Kresin
61c2a7339a image: remove padding parameter from append-kernel/append-rootfs
Using pad-to instead of passing the optional padding to append-kernel
or append-rootfs. It could be that the value of a variable is passed.
In case the variable is empty no error is thrown.

Furthermore the purpose of the extra parameter is hard to get without
reading the code.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-13 19:36:41 +02:00
Mathias Kresin
1cd0a4c688 image: add KERNEL_SIZE to the default device vars
This reverts commit ec37a56587 and fixes
the underlying issue.
2016-09-13 19:36:41 +02:00
Felix Fietkau
d27bce8d28 build: drop UBI EOF marker from images by default
Only add them where they are actually required.
Should help with compatibility issues with stock U-Boot images that
access UBI

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-12 18:21:52 +02:00
Mathias Kresin
c1578d4fc9 cleanup ucidef_set_interface* usage
- quote the interface name
- remove call of not existing function
- remove the proto if it's the default proto

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-10 15:32:25 +02:00
Mathias Kresin
e7ec7a08aa image: use k as unit suffix for blocksize
Use k as unit suffix for kilobyte to have a the same unit regardless of
the used filesystem.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-04 08:56:05 +02:00
Jo-Philipp Wich
db49dd894e build: rename sysupgrade-nand to sysupgrade-tar
Now that the "sysupgrade-nand" step is used by non-NAND targets as well,
rename it to "sysupgrade-tar" to make it more generic.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-07-29 16:53:03 +02:00
Felix Fietkau
33c8d35375 image: remove shell calls from legacy ubi/ubifs image code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-25 12:37:50 +02:00
Felix Fietkau
064bcdc259 kirkwood: fix UBIFS_OPTS variable in image build
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-25 12:30:19 +02:00
Felix Fietkau
650afe412b kirkwood: remove obsolete code for including kernel/dtb in rootfs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau
0538bbdc4d kirkwood: remove obsolete ubinize.cfg file
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau
5d4b044955 kirkwood: clean up redundant variables in the image building code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau
cfd1ef4b90 kirkwood: get rid of useless ubifs/ubi option variables
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-20 10:13:50 +02:00
Felix Fietkau
8e2764ce9b image.mk: clean up redundant code related to DEVICE_DTS
It is used by a core build template, so the variable should be
initialized and added to DEVICE_VARS in the core.
Same for DEVICE_DTS_DIR

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-15 14:14:11 +02:00
Felix Fietkau
e0ed6ec667 image: clean up UBI related device variable definitions
Move UBI related variable export to core, since the variables are used
by a core Build/ template

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-07-14 10:27:30 +02:00
Ben Whitten
b7baaaf782 kernel: Move append-dtb to common image-commands
This build step is used by various targets, move it to a common section.

Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
2016-06-22 19:32:06 +02:00
Felix Fietkau
6036768d46 kirkwood: install kernel binaries into bin/ for use with external storage
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-07 08:58:41 +02:00
Jo-Philipp Wich
52836866c9 kirkwood: add missing kernel symbol
The query for ARMADA_THERMAL is stalling the kconfig process and as long as we
do not package it, simply disable the symbol.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-05-24 19:41:27 +02:00
Felix Fietkau
934daa7b50 kirkwood: move ubi/ubifs options to the image makefile
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-19 15:18:12 +02:00
Luka Perkov
5a864190f0 kirkwood: refresh patches
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 49022
2016-03-14 17:13:22 +00:00
Luka Perkov
b5bcd4cf36 kirkwood: drop 3.18
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 49021
2016-03-14 17:12:08 +00:00
Luka Perkov
3ffb5cec14 kirkwood: switch to 4.4
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 49020
2016-03-14 17:06:21 +00:00
Luka Perkov
5c457db8e5 kirkwood: add 4.4 support
Dropped patches because they applied upstream:

- 120-iomega_ix2_200.patch
- 150-pogoplug_e02.patch

Tested on dockstar and goflexnet.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 49019
2016-03-14 17:06:20 +00:00
Luka Perkov
76c2c676ec kirkwood/goflexnet/goflexhome: change mtd layout to use the last 3 mb
Previous the uboot was overwriting the device-tree's mtd layout to use
the last 3 mb.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 49015
2016-03-14 17:06:15 +00:00
Luka Perkov
ab13a001dd kirkwood/goflexhome/goflexnet: merge "root" and unused mtd partitions into one volume "ubi"
The kernel will automatic attach mtd partitions named 'ubi' to ubi0.
Renaming the "root" partition into "ubi" will safe arguments
from the kernel cmdline.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 49014
2016-03-14 17:06:14 +00:00
Luka Perkov
33f76a486d linux/kirkwood: migrate goflexhome/goflexnet to new ubi style
Also using the new image build step format

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 49013
2016-03-14 17:06:12 +00:00
Luka Perkov
e9e16bef08 kirkwood/dockstar: rename partition into ubi to use auto detection of target mtd
the kernel tries to use "ubi" or "data" labeled partition to find it's root filesystem.
dockstar don't need anymore mtdparts= nor root= bootarguments

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 49011
2016-03-14 17:06:10 +00:00
Luka Perkov
afa1c47e71 kirkwood/dockstar: use ubi(kernel, squashfs, ubifs) images
The new image requires `bootz` because of devicetree appending.
To flash a new image boot initramfs:

  tftpboot 0x800000 openwrt-kirkwood-dockstar-initramfs-kernel.bin
  bootz 0x800000

  # detach if already attached
  ubidetach -p /dev/$(grep ubi /proc/mtd|awk -F: '{print $1}')
  # scp openwrt-kirkwood-dockstar-squashfs-factory.bin /tmp
  ubiformat -f /tmp/openwrt-kirkwood-dockstar-squashfs-factory.bin
  # attach is important to resize rootfs_data otherwise it wont boot
  ubiattach -p /dev/$(grep ubi /proc/mtd|awk -F: '{print $1}')

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 49010
2016-03-14 17:06:09 +00:00
Luka Perkov
1b9c171f88 kirkwood: add DEVICE_VAR KERNEL_IN_UBI for kernel as volume in ubi images
depending on KERNEL_IN_UBI, the image.mk will create a ubi volume for the kernel

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 49009
2016-03-14 17:06:08 +00:00
Luka Perkov
ef75442989 kirkwood: add feature devicetree
this platform already uses devicetree

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 49008
2016-03-14 17:06:06 +00:00
Luka Perkov
6bc24292ab kirkwood: drop 4.3 support
Signed-off-by: Luka Perkov <luka.perkov@sartura.hr>

SVN-Revision: 48499
2016-01-25 22:54:52 +00:00
Felix Fietkau
57776e68ce base-files: remove default /etc/config/network, generate it via board.d instead
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48493
2016-01-25 16:30:41 +00:00
Felix Fietkau
2499a57d92 targets: add kernel image dependencies on device tree files
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48146
2016-01-06 18:39:06 +00:00
Jo-Philipp Wich
67e1c87012 all: drop old uci-defaults.sh
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47867
2015-12-11 15:26:06 +00:00
Jo-Philipp Wich
08848936dd all: remove redundant board.d/00_model files
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47753
2015-12-04 11:07:06 +00:00
Jo-Philipp Wich
296212c301 kirkwood: add missing board_config_flush(), remove dead code
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47745
2015-12-03 23:13:04 +00:00
Jo-Philipp Wich
80a3e65a9d kirkwood, ipq806x: fix board.d script permissions
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47735
2015-12-03 22:42:13 +00:00
Jo-Philipp Wich
7514b6d73b kirkwood: switch from uci-defaults to board.d
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47733
2015-12-03 22:27:18 +00:00
Luka Perkov
84c7a31535 kirkwood: nsa310s: fix partition size
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 47504
2015-11-18 21:35:04 +00:00
Luka Perkov
4e239d9fdb kirkwood: add Linksys routers to default profile
Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47458
2015-11-11 12:48:30 +00:00
Luka Perkov
ba26e9f60f kirkwood: rename EA3500/EA4500 profiles
Match the engineering board names now used elsewhere.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47436
2015-11-10 00:17:01 +00:00
Luka Perkov
31c7de0313 kirkwood: add diag LED on Linksys EA3500
Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47435
2015-11-10 00:16:56 +00:00
Luka Perkov
b0e7ca4f8f kirkwood: support sysupgrade on Linksys EA[34]500
This automatically writes to the alternate firmware partition
(on Linksys's dual firmware layout) using code borrowed from
the WRT1900AC port.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47434
2015-11-10 00:16:42 +00:00
Luka Perkov
ea8ac0999c kirkwood: support Linksys boot counter on EA[34]500
This is done with existing code from the WRT1900AC port.
It makes sure the "auto_recovery" bootloader option is set,
and resets the s_env boot counter after a successful boot.

This gives users without a serial console connection some
measure of safety.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47433
2015-11-10 00:16:37 +00:00
Luka Perkov
6acb552eee kirkwood: generate factory images for Linksys EA[34]500
This is done with the new image generation system and board names.
It also generates a sysupgrade.tar image.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47432
2015-11-10 00:16:35 +00:00
Luka Perkov
5d4bbb5f5b kirkwood: find active Linksys root partition
This is imported verbatim from the mvebu WRT1900AC port.

It picks up the current boot partition from the kernel command line,
then renames that partition "ubi" so that it auto-mounts.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47431
2015-11-10 00:16:33 +00:00
Luka Perkov
ad8f6370de kirkwood: consistently use engineering board names
Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47430
2015-11-10 00:16:28 +00:00
Luka Perkov
3ef14d0c3d kirkwood: rework Linksys EA[34]500 DTS
- Use board engineering names rather than marketing names

- Linksys uses a dual firmware layout, where the bootloader
  will switch to the other stored image when one fails to
  boot three consecutive times.

  In order to make this firmware compatible with the factory
  images and the stock bootloader we must match this layout.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47429
2015-11-10 00:16:24 +00:00
Luka Perkov
49db4924d7 kirkwood: enable squashfs-on-ubiblock support
Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 47428
2015-11-10 00:16:14 +00:00
Luka Perkov
47668ffd8e kirkwood: add support for 4.3
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 47386
2015-11-04 22:28:47 +00:00
Luka Perkov
805492bda9 kirkwood: pogo_e02: use mainline led definitions
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 47385
2015-11-04 22:28:42 +00:00
Hauke Mehrtens
55a912f43e kernel: update kernel 3.18 to version 3.18.23
Changelog:
 * https://cdn.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.22
 * https://cdn.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.23

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47334
2015-11-01 13:45:57 +00:00
Luka Perkov
6a18146206 kirkwood: add initial support for NSA310s
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 47330
2015-11-01 01:13:16 +00:00
Felix Fietkau
2e7df6312d kirkwood: image: Remove custom mkfs targz override as base should be fine now
It was wrong anyway, missing file sort order parameter which was fixed
in base month ago.

Signed-off-by: Petr Štetiar <ynezz@true.cz>

SVN-Revision: 47313
2015-10-31 09:28:34 +00:00
Felix Fietkau
8a237d1f03 kirkwood: image: Refactor sanitize_profile_name using PROFILE_SANITIZED var
Signed-off-by: Petr Štetiar <ynezz@true.cz>

SVN-Revision: 47309
2015-10-31 09:27:56 +00:00
Jonas Gorski
c853db24e0 kirkwood: add wpad-mini to router profiles
Without it the wifi isn't really usable.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46565
2015-08-05 13:56:02 +00:00
Jonas Gorski
dbe4173b20 image: fix jffs2(_nand) image generation
Variables dependend on JFFS2_BLOCKSIZE and NANDBLOCK_SIZE are used
for template generation, so need to be present before inclusion of
image.mk in target image Makefiles.
So move all declarations to before any includes.

Fixes: r42878 ("image.mk: clean up and parallelize mkfs calls")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46564
2015-08-05 13:55:52 +00:00
Felix Fietkau
564fdae968 kirkwood: disable TSO on the ethernet device by default, fixes data corruption issues (#19735)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45776
2015-05-27 14:56:13 +00:00
Felix Fietkau
9f0ffef86a kirkwood: disable the bogus CONFIG_IP_ADVANCED_ROUTER override (#19722)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45753
2015-05-25 22:59:15 +00:00
Luka Perkov
7437be53ba kirkwood: add support for the Seagate GoflexHome
Add Support for the Seagate GoflexHome <http://wiki.openwrt.org/toh/seagate/goflexhome>

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 45647
2015-05-08 20:12:39 +00:00
Jonas Gorski
954004eccc kernel: disable INET_LRO by default
INET_LRO deprecated and there are exactly two drivers using it, neither
being included in any of the targets enabling INET_LRO. At the same time
both drivers needing it select it.

So just disable it for everyone.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45584
2015-04-28 13:31:08 +00:00
Luka Perkov
cc8628a6a3 kirkwood: put uboot-envtools in DEFAULT_PACKAGES
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 45477
2015-04-17 13:47:09 +00:00
John Crispin
6d0ad03fac kernel: remove references to kmod-of-i2c
these break the IB since the module is part of i2c-core now

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 45363
2015-04-10 13:39:33 +00:00
John Crispin
cacc152a37 kirkwood: add missing symbol that broke full builds
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44641
2015-03-10 11:03:10 +00:00
John Crispin
d15ac306fa kernel: move KERNFS to generic config
KERNFS symbol is selected by SYSFS, so place it in generic config.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 44615
2015-03-06 07:56:47 +00:00
John Crispin
f04a268a04 kernel: disable ARCH_NEEDS_CPU_IDLE_COUPLED
Disable ARCH_NEEDS_CPU_IDLE_COUPLED by-default in generic config, since
only one platfrom (omap) needs them.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 44614
2015-03-06 07:56:34 +00:00
John Crispin
fa097e5ae5 kernel: disbale HAMRADIO in generic config
HAMRADIO enabled in all generic configs, but no one platform directly
use related drivers/protocols. This symbol is only used for kmod-ax25
package modules. Furthermore, half of platforms explicitly disables
this symbol, what silently disables build of modules for kmod-ax25
package.

So disable HAMRADIO by-default in generic config, add it to kmod-ax25
package and remove it from platform specific configs.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 44613
2015-03-06 07:56:21 +00:00
John Crispin
6617845711 kernel: move MTD_SPLIT_SUPPORT to generic config
CONFIG_MTD_SPLIT_SUPPORT symbol default value is 'y' and many platform
specific configs explicitly enables it, while no one platform disables
this symbol. So place it in generic config and remove from platform
specific configs.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>

SVN-Revision: 44612
2015-03-06 07:56:08 +00:00
Luka Perkov
f40e7946ce kirkwood: drop support for 3.14
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 44610
2015-03-05 23:43:27 +00:00
Luka Perkov
37cef98844 kirkwood: switch to 3.18
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 44609
2015-03-05 23:43:24 +00:00
Luka Perkov
5cce8f9a0f kirkwood: Seagate GoFlex Net
Add GoFlex Net "Board Name" , set and cleanup network default and LEDs.
Remove kmod-rtc-marvell from default packages, as the GoFlex net does not have a RTC.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 44422
2015-02-12 14:39:26 +00:00
Luka Perkov
7294b892dc kirkwood: refresh kernel config
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 44319
2015-02-08 12:01:39 +00:00
Luka Perkov
81db848656 targets: base-files: diag.sh does not need to be executable
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 44305
2015-02-07 19:58:58 +00:00
Luka Perkov
a46bb6ec6a kirkwood: add wpad-mini to guruplug profile
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>

SVN-Revision: 44125
2015-01-25 13:39:24 +00:00
Luka Perkov
c8e9b5d13e kirkwood: enable swconfig by default on EA3500
Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 44124
2015-01-25 13:11:07 +00:00
Luka Perkov
2907ad2363 kirkwood: fix EA3500 ubi options
Previous options resulted in a nonfunctional image.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 44123
2015-01-25 13:11:04 +00:00
Luka Perkov
86f1a60549 kirkwood: drop port-based VLAN setup
Using port-based VLANs depends on a non-standard
swconfig parameter, which compilcates things like
LuCI that don't know about it. This patch changes
the default to use 802.1q VLANs internally in the
switch, but without tagging packets since we have
two Ethernet ports.

iperf3 tests indicate no difference in performance
versus port-based VLANs when the CPU port is not
using tags.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 44122
2015-01-25 13:11:02 +00:00
Luka Perkov
34f6c6fc38 kirkwood: enable switch on Linksys EA3500
Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 44036
2015-01-18 16:45:01 +00:00
John Crispin
8698398a6e target: kirkwood: fix leds defaults config
Fix missing parameters in 01_leds

Signed-off-by: Gerald Kerma <dreagle@doukki.net>

SVN-Revision: 44007
2015-01-17 14:39:01 +00:00
Luka Perkov
a1872182bb mvsw6171: rename to 'mvsw61xx'
In preparation for properly supporting switches
beyond the 88E6171.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 43935
2015-01-11 17:19:58 +00:00
Imre Kaloz
5744500ab6 we've changed places with Luka, reflect that :)
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 43774
2014-12-25 22:34:15 +00:00
Luka Perkov
873202fc0b kirkwood: add *plugs to uci-defaults
Set defaults health led to a timer heartbeet (200/800)
and populate network for:

- GuruplugServerPlus
- SheevaPlug
- SheevaPlug with eSATA

Signed-off-by: Gerald Kerma <dreagle@doukki.net>

SVN-Revision: 43752
2014-12-19 11:05:13 +00:00
Luka Perkov
39743e45f8 kikwood: populate kirkwood.sh with new boards
- SheevaPlug
- SheevaPlug with eSATA
- GuruplugServerPlus

Signed-off-by: Gerald Kerma <dreagle@doukki.net>

SVN-Revision: 43751
2014-12-18 18:38:43 +00:00
Luka Perkov
ec9a0f898a kirkwood: set default EA4500 switch config
This maps the LAN ports to eth0 and WAN port to eth1.
Since there are two interfaces the 802.1q VLAN mode
is unnecessary and left disabled. Port-based VLANs
are used instead.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 43750
2014-12-18 18:38:38 +00:00
Luka Perkov
309e74b86d kirkwood: add sheevaplug and derivatives
Add kirkwood FDT:
- SheevaPlug
- SheevaPlug with eSATA
- GuruplugServerPlus
- Topkick1281P2

Signed-off-by: Gérald Kerma <drEagle@doukki.net>

SVN-Revision: 43735
2014-12-17 08:33:55 +00:00
John Crispin
019ea725aa add "preinit_regular" diag.sh set_state argument
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 43715
2014-12-15 10:37:00 +00:00
John Crispin
2db6da5532 kirkwood: enable EA4500 switch on 3.18
Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 43704
2014-12-14 08:57:58 +00:00
John Crispin
d7b4bf8966 kirkwood: Iomega ix2-200: wire up the GPIO poweroff driver in the DTS file
Signed-off-by: Richard Kunze <richard.kunze@web.de>

SVN-Revision: 43670
2014-12-12 17:14:14 +00:00