Add target for Loongson LoongArch64-based boards.
LoongArch is a new RISC ISA developed by Loongson. It's a bit like
MIPS or RISC-V. LoongArch includes both 32-bit and 64-bit versions
(LoongArch32/LoongArch64).
Loongson 3A5000 and 3A6000 are the two existing CPUs of LoongArch64
and is used for PC products. It's BIOS supports ACPI and UEFI-only
boot. These CPUs supports SMP and SMT.
At present only LoongArch64 is supported by linux kernel.
Toolchain requirement:
binutils >= 2.40
gcc >= 13.1
For details, please check the following links:
https://lwn.net/Articles/861951/https://loongson.github.io/LoongArch-Documentation/README-EN.html
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Increasing the size of the rootfs_data filesystem has become a ever
repeating discussion and seems to be the most important thing for
users of the MediaTek-based BananaPi boards.
Using the whole remaining size of a microSD or the eMMC for rootfs_data
doesn't make sense for many reasons, but neither does the current
default of 104 MiB for the 'rootfs' partition size.
Increase the 'rootfs' partition size to 448 MiB which will result in
the sdcard image being exactly 512 MiB. Finding a microSD card smaller
than 512 MiB and still working could anyway be difficult in 2024.
That will allow users to install even bloatware written in Go or other
space-hungry languages while still leaving most of the space unallocated
for additional partitions or volumes to be used for persistent user
data.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Not having a journal by default is a major "gotcha".
Because openwrt does not fsck on boot, a power loss without journaling
can result in a dirty filesystem that openwrt will mount as read-only
which requires intervention to restore the router to working order.
Signed-off-by: Jordan Woyak <jordan.woyak@gmail.com>
GRUB_SERIAL is also used for the default serial on the target and not
only in grub. When no grub was build it was not available and the build
fails.
Rename GRUB_SERIAL to TARGET_SERIAL and make it always available on x86
and armsr targets.
Fixes: #14063
Fixes: b10768476f ("x86,armsr: interpolate GRUB_SERIAL into /etc/inittab")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, ipq807x only covers Qualcomm IPQ807x SoC-s.
However, Qualcomm also has IPQ60xx and IPQ50xx SoC-s under the AX WiSoC-s
and they share a lot of stuff with IPQ807x, especially IPQ60xx so to avoid
duplicating kernel patches and everything lets make a common target with
per SoC subtargets.
Start doing that by renaming ipq807x to qualcommax so that dependencies
on ipq807x target can be updated.
Signed-off-by: Robert Marko <robimarko@gmail.com>
armvirt target has been renamed to armsr (Arm SystemReady),
so the config defaults need to be changed as well.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The nominal partition type for EFI boot partitions is FAT32,
which has a minimum size of 32MiB on a 512-byte-sector block device.
To ensure that the boot partition is created as FAT32 set a size
well above this minimum.
A useful discussion about EFI partition sizes can be found here:
https://superuser.com/questions/1310927/what-is-the-absolute-minimum-size-a-uefi-system-partition-can-be
I have found 128MiB works pretty consistently across both
tools (mkfs.fat) and firmwares (EDKII)
Signed-off-by: Mathew McBride <matt@traverse.com.au>
This adds a separate package for EFI on Arm SystemReady
compatible machines. 32-bit Arm UEFI is supported as well.
It is very similar to x86-64 EFI setup, without the
need for BIOS backward compatibility and slightly
different default modules.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Sourcing of image/Config.in will not happen
When a target is installed from target/linux/feeds/
Signed-off-by: Prasun Maiti <prasunmaiti87@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
Kconfig docs say:
> The default value deliberately defaults to 'n' in order to avoid
> bloating the build.
Apply this rule everywhere, to avoid more cloning of bad examples
Signed-off-by: Tony Butler <spudz76@gmail.com>
Requires: tools/lz4, tools/lzop
complete the wiring so that these options work:
* `CONFIG_KERNEL_INITRAMFS_COMPRESSION_LZO`
* `CONFIG_KERNEL_INITRAMFS_COMPRESSION_LZ4`
Signed-off-by: Tony Butler <spudz76@gmail.com>
[remove blocking dependencies for separate ramdisk, fix lzop options]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Qualcomm Atheros IPQ807x is a modern WiSoC featuring:
* Quad Core ARMv8 Cortex A-53
* @ 2.2 GHz (IPQ8072A/4A/6A/8A) Codename Hawkeye
* @ 1.4 GHz (IPQ8070A/1A) Codename Acorn
* Dual Band simultaneaous IEEE 802.11ax
* 5G: 8x8/80 or 4x4/160MHz (IPQ8074A/8A)
* 5G: 4x4/80 or 2x2/160MHz (IPQ8071A/2A/6A)
* 5G: 2x2/80MHz (IPQ8070A)
* 2G: 4x4/40MHz (IPQ8072A/4A/6A/8A)
* 2G: 2x2/40MHz (IPQ8070A/1A)
* 1x PSGMII via QCA8072/5 (Max 5x 1GbE ports)
* 2x SGMII/USXGMII (1/2.5/5/10 GbE) on Hawkeye
* 2x SGMII/USXGMII (1/2.5/5 GbE) on Acorn
* DDR3L/4 32/16 bit up to 2400MT/s
* SDIO 3.0/SD card 3.0/eMMC 5.1
* Dual USB 3.0
* One PCIe Gen2.1 and one PCIe Gen3.0 port (Single lane)
* Parallel NAND (ONFI)/LCD
* 6x QUP BLSP SPI/I2C/UART
* I2S, PCM, and TDMA
* HW PWM
* 1.8V configurable GPIO
* Companion PMP8074 PMIC via SPMI (GPIOS, RTC etc)
Note that only v2 SOC models aka the ones ending with A suffix are
supported, v1 models do not comply to the final 802.11ax and have
lower clocks, lack the Gen3 PCIe etc.
SoC itself has two UBI32 cores for the NSS offloading system, however
currently no offloading is supported.
Signed-off-by: Robert Marko <robimarko@gmail.com>
add help text for `TARGET_SQUASHFS_BLOCK_SIZE` to match the only valid
settings accepted by `mksquashfs4` ("block size not power of two or not
between 4096 and 1Mbyte") thus for this setting in "KB", the set:
`4, 8, 16, 32, 64, 128, 256, 512, 1024`
replace `squashfs-lzma` with `squashfs` in the description for
`TARGET_ROOTFS_SQUASHFS` because it has various compressions, and not
just lzma as it did in the past
cosmetic change with no functional effect
Signed-off-by: Tony Butler <spudz76@gmail.com>
some config `depends on` lines contained outdated kernel version checks
that can no longer happen and had become non-operational; clean them up
cosmetic change with no functional effect
Signed-off-by: Tony Butler <spudz76@gmail.com>
This reverts commit ce1346a8fc.
Seems to cause buildbot compilation to fail and require more testing.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Added support to generate dynamic-sized VHDX images for Hyper-V.
Compile-tested on x86 and run-tested on Windows 10 21H2 (Hyper-V).
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
In OpenWrt, /var is symlinked to /tmp by default. This is done to reduce
the amount of writes to the flash chip, which often have not the
greatest durability. As a result, things like DHCP or UPnP lease files,
are not persistent across reboots.
Since OpenWrt can run on devices with more durable storage, it makes
sense to have an option for a persistent /var. Add an option to make
/var persistent. When enabled, /var will no longer be symlinked to /tmp,
but /var/run will be symlink to /tmp/run, as it should contains only
files that should not be kept during reboot. The option is off by
default, to maintain the current behaviour.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The grub2 and grub2-efi packages should only contain boot-related code.
grub-bios-setup is the same as grub-editenv, they are both grub2 tools
and should be placed in a separate package.
Signed-off-by: 李国 <uxgood.org@gmail.com>
[use AUTORELEASE and update to SPDX]
Signed-off-by: Paul Spooren <mail@aparcar.org>
The code interprets these config values as Mebibytes rather than
Megabytes so modify the description accordingly.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
[fix commit title prefix]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* show only if target supports it (ie. seperate_ramdisk feature set)
* select XZ compression by default of ramdisk is seperate
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of embedding the initrd cpio archive into the kernel, allow
for having an external ramdisk added to the FIT or uImage.
This is useful to overcome kernel size limitations present in many
stock bootloaders, as the ramdisk is then loaded seperately and doesn't
add to the kernel size. Hence we can have larger ramdisks to host ie.
installers with all binaries to flash included (or a web-based
firmware selector).
In terms of performance and total size the differences are neglectible.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The license folder is a core part of OpenWrt and all GPL-2.0 licensed.
Use SPDX license tags to allow machines to check licenses.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[rebase, keep some Copyright lines, sharpen commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target is still on kernel 4.14, and recent attempts to move it to
kernel 5.4 have not led to success. The device tester reported that it
wouldn't boot with the following messages:
From sysupgrade:
Press any key within 4 seconds to enter setup....
loading kernel from nand... OK
setting up elf image... OK
jumping to kernel code
At this point the system hangs.
From CompactFlash:
Press any key within 4 seconds to enter setup....
Booting CF
Loading kernel... done
setting up elf image... kernel out of range kernel loading failed
The tester reported that the same was observed with current master
(kernel 4.14) as well. This looks like some kernel size restriction.
Since this target is quite old and only supports one device, and since
nobody else seemed interested in working on this for quite some time,
I decided to not put further work into analyzing the problem and drop
this together with the other 4.14-only targets.
Patchwork series:
https://patchwork.ozlabs.org/project/openwrt/list/?series=197066&state=*
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target has been mostly replaced by ath79 and won't be included
in the upcoming release anymore. Finally put it to rest.
This also removes all references in packages, tools, etc. as well as
the uboot-ar71xx and vsc73x5-ucode packages.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the MikroTik RouterBOARD RB493G, ported
from the ar71xx target.
See https://routerboard.com/RB493G for details
Specification:
- SoC Qualcomm Atheros AR7161
- RAM: 256 MiB
- Storage: 128MiB NAND
- Ethernet: 9x 1000/100/10 Mbps
- USB 1x 2.0 / 1.0 type A
- PCIe: 3x Mini slot
- MicroSD slot
Working:
- Board/system detection
- Ethernet
- SPI
- NAND
- LEDs
- USB
- Sysupgrade
Enabled (but untested due to lack of hardware):
- PCIe - ath79_pci_irq struct has the slot/pin/IRQ mappings if needed
Installation methods:
- tftp boot initramfs image, scp then flash via "sysupgrade -n"
- nand boot existing OpenWrt, scp then flash via "sysupgrade -n"
Notes:
- initramfs image will not work if uncompressed image size over ~8.5Mb
- The "rb4xx" drivers have been enabled
Signed-off-by: Christopher Hill <ch6574@gmail.com>
Add EFI platform bootable images for x86 platforms. These images can
also boot from legacy BIOS platform.
EFI System Partition need to be fat12/fat16/fat32 (not need to load
filesystem drivers), so the first partition of EFI images are not ext4
filesystem any more.
GPT partition table has an alternate partition table, we did not
generate it. This may cause problems when use these images as qemu disk
(kernel can not find rootfs), we pad enough sectors will be ok.
Signed-off-by: 李国 <uxgood.org@gmail.com>
[part_magic_* refactoring, removed genisoimage checks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit introduces few related changes which need to be done in
single commit to keep images buildable between git revisions. In result
it retains all previous image creation possibilities with slight name
change of generated images. Brief summary of the commit:
* Split up image generation recipe to smaller chunks to make it more
generic and reusable.
* Make iso images x86 specific and drop their definition as root
filesystem.
* Convert image creation process to generic code specified in image.mk.
* Make geode subtarget inherit features from the main target instead of
redefining them.
* For subtargets create device definitions with basic packages set.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[rebased]
Signed-off-by: Paul Spooren <mail@aparcar.org>
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.
Despite, since subtargets range from bcm2708 to bcm2711, it seems
appropriate to use bcm27xx instead of bcm2708 (again, as already done
for BOARDNAME).
This also renames the packages brcm2708-userland and brcm2708-gpu-fw.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
Change TARGET_ROOTFS_PARTSIZE from 128 to 104 MiB, so the whole image
(bootloader + boot + root) will fit on a 128MB CF card by default.
With these settings, the generated images (tested on x86-generic and
x86-64) have 126,353,408 bytes; the smallest CF card marketed as "128MB"
that I found a datasheet for (a Transcend TS128MCF80) has 126,959,616
bytes.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
As we're now going to pad all images by default to 128MiB let's enable
compression of the images for armvirt and malta in order to save some
space and bandwidth.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
As we're now going to pad all images by default, lets decrease the
default rootfs partition size from 256MiB to 128MiB in order to save
some space.
I'm keeping it above 100MiB in order to keep current behavior, where
overlay filesystem is using F2FS.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It's being used only in x86 target to produce combined images, where
it's mandatory to have padded images in order to produce working
squashfs combined images usable in QEMU.
Currently we're producing unusable x86 combined squashfs images
(18.06.1, 18.06.2 and snapshots) as we don't enable TARGET_IMAGES_PAD,
thus providing very small space for the overlay filesystem, leading to
the following with OpenWrt 18.06.1 r7258-5eb055306f images on x86 QEMU:
root@(none):/# mount | egrep 'root|overlay'
/dev/root on /rom type squashfs
/dev/loop0 on /overlay type ext4
overlayfs:/overlay on / type overlay
root@(none):/# df -h | egrep 'root|overlay|Size'
Filesystem Size Used Available Use% Mounted on
/dev/root 2.5M 2.5M 0 100% /rom
/dev/loop0 113.0K 8.0K 97.0K 8% /overlay
overlayfs:/overlay 113.0K 8.0K 97.0K 8% /
So we should rather ensure proper image padding in image generation code
and we shouldn't rely on config options in order to generate usable
images.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit eae6cac6a3 ("lantiq: add support for AVM FRITZ!Box 7362 SL"), but
one needs an initramfs image to flash OpenWrt from stock firmware (as
described in the commit log). This patch has the initramfs image built
by default.
Thanks to blogic (for pointing to the FEATURES declaration in the target
Makefiles) and Musashino on the forum for suggesting
config/Config-images.in needed editing too. While at it, reorder the
TARGET_INITRAMFS_COMPRESSION_LZMA declarations alphabetically.
This patch will result in initramfs images for all lantiq subtargets
that have the ramdisk flag set. I tested on the falcon and ase
subtargets, which lack that flag, to confirm they don't produce any
initramfs images with this patch - which they do not.
Given the limited scope of the lantiq (sub)target(s), blogic indicated
this should be OK.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[fixed the wrong reference to eae6cac6a3 commit]
VBoxManage is not used and the image is created with proper permisions:
0f5d0f6 image: use internal qemu-img for vmdk and vdi images drop host
dependencies on qemu-utils and VirtualBox
Unreachable config symbols:
9e0759e x86: merge all geode based subtargets into one
No need to define those symbols since x86_64 is subtarget of x86:
196fb76 x86: make x86_64 a subtarget instead of a standalone target
Unreachable config symbols, so remove GRUB_ROOT:
371b382 x86: remove the xen_domu subtarget
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This patch adds the boot-part feature which enables the brcm2708
target move from the custom boot partition size config option to
the generic CONFIG_TARGET_KERNEL_PARTSIZE.
Note:
For people using custom images: Just like with
CONFIG_TARGET_ROOTFS_PARTSIZE changing the value
can cause sysupgrade to repartition the device!
Make sure to have a backup in this case.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds the boot-part feature to the apm82181 sata target.
This makes it possible to configure the boot partition size with
the generic CONFIG_TARGET_KERNEL_PARTSIZE symbol.
Please note: For people using custom images: Just like with
CONFIG_TARGET_ROOTFS_PARTSIZE changing the value can cause
sysupgrade to repartition the device!
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The sdcard image generation uses CONFIG_TARGET_ROOTFS_PARTSIZE, which is
currently bound to TARGET_ROOTFS_EXT4FS on this target.
Since the rootfs is squashfs anyway, allow deselecting of the ext4fs
one.
Sort the target list alphabetically while here.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Extend the small_flash feature to disable swap, core dumps, and
kernel debug info, and change the squashfs block size to 1024KiB.
Also change squashfs fragment cache to 2 for small_flash to ease memory
usage.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
