mirror of
https://github.com/openwrt/openwrt.git
synced 2025-03-22 03:55:22 +00:00
ramips: add support for Zyxel LTE7490-M904
The Zyxel LTE7490-M904 is an 802.3at PoE powered LTE outdoor (IP68) CPE with integrated directional antennas. Specifications: - SoC: MediaTek MT7621AT - RAM: 256 MB - Flash: 128 MB MB NAND (MX30LF1G18AC) - WiFi: MediaTek MT7603E 802.11b/g/n - Switch: 1 LAN port (1 Gbps) - LTE/3G/2G: Quectel EG18-EA LTE-A Cat. 18 connected by USB3 to SoC - SIM: 1 micro-SIM slots under transparent cover - Buttons: Reset, WLAN under same cover - LEDs: Multicolour green/red/amber under same cover (visible) - Power: 802.3at PoE via LAN port The device is built as an outdoor ethernet to LTE bridge or router. The wifi interface is intended for installation and/or temporary management purposes only. UART Serial: 57600N1, located on populated 5 pin header J5: [o] GND [ ] key - no pin [o] RX [o] TX [o] 3.3V Vcc Remove the SIM/button/LED cover and 12 screws holding the back plate and antenna cover together. Be careful with the cables. Installation from OEM web GUI: - Log in as "admin" on OEM web GUI - Upload OpenWrt initramfs-recovery.bin image on the Maintenance -> Firmware page - Wait for OpenWrt to boot and ssh to root@192.168.1.1 - Sysupgrade to the OpenWrt sysupgrade image and reboot For more details about flashing see: 2449a63208 (ramips: mt7621: Add support for ZyXEL NR7101, 2021-04-19) Main porting work done by Ernesto Castellotti <ernesto@castellotti.net>: bf1c12f68b (ramips: add support for ZyXEL LTE7490-M904, 2023-12-20) Signed-off-by: Eric Schäfer <eric@es86.de> Link: https://github.com/openwrt/openwrt/pull/17485 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit is contained in:
Eric Schäfer
Hauke Mehrtens
parent
3961b71776
commit
f3eca7cbc1
@ -138,6 +138,7 @@ zyxel,lte3301-plus)
|
||||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x1000" "0x80000"
|
||||
;;
|
||||
zyxel,lte5398-m904|\
|
||||
zyxel,lte7490-m904|\
|
||||
zyxel,nr7101)
|
||||
idx="$(find_mtd_index Config)"
|
||||
[ -n "$idx" ] && \
|
||||
|
||||
185
target/linux/ramips/dts/mt7621_zyxel_lte7490-m904.dts
Normal file
185
target/linux/ramips/dts/mt7621_zyxel_lte7490-m904.dts
Normal file
@ -0,0 +1,185 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "mt7621.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
compatible = "zyxel,lte7490-m904", "mediatek,mt7621-soc";
|
||||
model = "Zyxel LTE7490-M904";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_red;
|
||||
led-failsafe = &led_amber;
|
||||
led-running = &led_green;
|
||||
led-upgrade = &led_amber;
|
||||
label-mac-device = &gmac0;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_amber: led_amber {
|
||||
function = LED_FUNCTION_STATUS;
|
||||
color = <LED_COLOR_ID_AMBER>;
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_green: led_green {
|
||||
function = LED_FUNCTION_STATUS;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_red: led_red {
|
||||
function = LED_FUNCTION_STATUS;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
wps {
|
||||
label = "wlan";
|
||||
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WLAN>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gpio {
|
||||
lte_pwrkey {
|
||||
gpio-hog;
|
||||
gpios = <4 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "lte-pwrkey";
|
||||
};
|
||||
|
||||
lte_power {
|
||||
gpio-hog;
|
||||
gpios = <18 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "lte-power";
|
||||
};
|
||||
};
|
||||
|
||||
&nand {
|
||||
status = "okay";
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "Bootloader";
|
||||
reg = <0x0 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
label = "Config";
|
||||
reg = <0x80000 0x80000>;
|
||||
};
|
||||
|
||||
factory: partition@100000 {
|
||||
label = "Factory";
|
||||
reg = <0x100000 0x40000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
eeprom_factory_0: eeprom@0 {
|
||||
reg = <0x0 0x400>;
|
||||
};
|
||||
|
||||
macaddr_factory_e000: macaddr@e000 {
|
||||
reg = <0xe000 0x6>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@140000 {
|
||||
label = "Kernel";
|
||||
reg = <0x140000 0x1ec0000>;
|
||||
};
|
||||
|
||||
partition@540000 {
|
||||
label = "ubi";
|
||||
reg = <0x540000 0x1ac0000>;
|
||||
};
|
||||
|
||||
partition@2140000 {
|
||||
label = "Kernel2";
|
||||
reg = <0x2140000 0x1ec0000>;
|
||||
};
|
||||
|
||||
partition@4000000 {
|
||||
label = "wwan";
|
||||
reg = <0x4000000 0x100000>;
|
||||
};
|
||||
|
||||
partition@4100000 {
|
||||
label = "data";
|
||||
reg = <0x4100000 0x1000000>;
|
||||
};
|
||||
|
||||
partition@5100000 {
|
||||
label = "rom-d";
|
||||
reg = <0x5100000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@5200000 {
|
||||
label = "reserve";
|
||||
reg = <0x5200000 0x80000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
wifi@0,0 {
|
||||
compatible = "mediatek,mt76";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
nvmem-cells = <&eeprom_factory_0>;
|
||||
nvmem-cell-names = "eeprom";
|
||||
};
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
nvmem-cells = <&macaddr_factory_e000>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&switch0 {
|
||||
ports {
|
||||
port@2 {
|
||||
status = "okay";
|
||||
label = "lan";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&state_default {
|
||||
gpio {
|
||||
groups = "i2c", "uart3", "jtag", "wdt";
|
||||
function = "gpio";
|
||||
};
|
||||
};
|
||||
@ -3531,6 +3531,20 @@ define Device/zyxel_lte5398-m904
|
||||
endef
|
||||
TARGET_DEVICES += zyxel_lte5398-m904
|
||||
|
||||
define Device/zyxel_lte7490-m904
|
||||
$(Device/nand)
|
||||
DEVICE_VENDOR := Zyxel
|
||||
DEVICE_MODEL := LTE7490-M904
|
||||
KERNEL_SIZE := 31488k
|
||||
DEVICE_PACKAGES := kmod-mt7603 kmod-usb3 kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
|
||||
KERNEL := $(KERNEL_DTB) | uImage lzma | \
|
||||
zytrx-header $$(DEVICE_MODEL) $$(VERSION_DIST)-$$(REVISION)
|
||||
KERNEL_INITRAMFS := $(KERNEL_DTB) | uImage lzma | \
|
||||
zytrx-header $$(DEVICE_MODEL) 9.99(ABQY.9)$$(VERSION_DIST)-recovery
|
||||
KERNEL_INITRAMFS_SUFFIX := -recovery.bin
|
||||
endef
|
||||
TARGET_DEVICES += zyxel_lte7490-m904
|
||||
|
||||
define Device/zyxel_nr7101
|
||||
$(Device/nand)
|
||||
DEVICE_VENDOR := Zyxel
|
||||
|
||||
@ -81,6 +81,7 @@ ramips_setup_interfaces()
|
||||
wavlink,ws-wn572hp3-4g|\
|
||||
winstars,ws-wn583a6|\
|
||||
yuncore,ax820|\
|
||||
zyxel,lte7490-m904|\
|
||||
zyxel,nr7101)
|
||||
ucidef_set_interfaces_lan_wan "lan" "wan"
|
||||
;;
|
||||
|
||||
@ -34,6 +34,7 @@ zyxel,lte5398-m904)
|
||||
ucidef_add_gpio_switch "usb_power" "Power USB Port" "usb_power" "1"
|
||||
ucidef_add_gpio_switch "lte_power" "Power LTE modem" "lte_power" "1"
|
||||
;;
|
||||
zyxel,lte7490-m904|\
|
||||
zyxel,nr7101)
|
||||
ucidef_add_gpio_switch "lte_reset" "Reset LTE/5G modem" "515"
|
||||
;;
|
||||
|
||||
@ -43,6 +43,7 @@ boot() {
|
||||
[ $(printf %d $(fw_printenv -n Image1Try)) -gt 0 ] && fw_setenv Image1Try 0
|
||||
;;
|
||||
zyxel,lte5398-m904|\
|
||||
zyxel,lte7490-m904|\
|
||||
zyxel,nr7101)
|
||||
[ $(printf %d $(fw_printenv -n DebugFlag)) -gt 0 ] || fw_setenv DebugFlag 0x1
|
||||
[ $(printf %d $(fw_printenv -n Image1Stable)) -gt 0 ] || fw_setenv Image1Stable 1
|
||||
|
||||
@ -196,6 +196,7 @@ platform_do_upgrade() {
|
||||
;;
|
||||
zyxel,lte3301-plus|\
|
||||
zyxel,lte5398-m904|\
|
||||
zyxel,lte7490-m904|\
|
||||
zyxel,nr7101)
|
||||
fw_setenv CheckBypass 0
|
||||
fw_setenv Image1Stable 0
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user