mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-25 16:31:13 +00:00
mvebu: puzzle-m902: add driver for MCU driving LEDs, fan and buzzer
Backport MFD driver for communicating with the on-board MCU found on IEI World Puzzle appliances. Improve the driver to support multiple LEDs, apply a default state and let MCU take care of blinking if timing is within supported range. Wire up LEDs and fan for Puzzle M902 in device tree. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This commit is contained in:
Daniel Golle
parent
c46202fb34
commit
f0c0b18234
@ -42,8 +42,10 @@ CONFIG_HOLES_IN_ZONE=y
|
||||
CONFIG_HW_RANDOM_OMAP=y
|
||||
CONFIG_ILLEGAL_POINTER_VALUE=0xdead000000000000
|
||||
CONFIG_LEDS_IS31FL319X=y
|
||||
CONFIG_LEDS_IEI_WT61P803_PUZZLE=y
|
||||
CONFIG_MARVELL_10G_PHY=y
|
||||
CONFIG_MDIO_DEVRES=y
|
||||
CONFIG_MFD_IEI_WT61P803_PUZZLE=y
|
||||
CONFIG_MFD_SYSCON=y
|
||||
CONFIG_MMC_SDHCI_XENON=y
|
||||
CONFIG_MODULES_USE_ELF_RELA=y
|
||||
@ -73,8 +75,12 @@ CONFIG_POWER_SUPPLY=y
|
||||
CONFIG_QUEUED_RWLOCKS=y
|
||||
CONFIG_QUEUED_SPINLOCKS=y
|
||||
CONFIG_RAS=y
|
||||
# CONFIG_RAVE_SP_CORE is not set
|
||||
CONFIG_REGULATOR_GPIO=y
|
||||
# CONFIG_RODATA_FULL_DEFAULT_ENABLED is not set
|
||||
CONFIG_SENSORS_IEI_WT61P803_PUZZLE_HWMON=y
|
||||
CONFIG_SERIAL_DEV_BUS=y
|
||||
CONFIG_SERIAL_DEV_CTRL_TTYPORT=y
|
||||
CONFIG_SPARSEMEM=y
|
||||
CONFIG_SPARSEMEM_EXTREME=y
|
||||
CONFIG_SPARSEMEM_MANUAL=y
|
||||
|
||||
@ -38,7 +38,10 @@
|
||||
ethernet8 = &cp2_eth2;
|
||||
spi1 = &cp0_spi0;
|
||||
spi2 = &cp0_spi1;
|
||||
serial1 = &cp0_uart0;
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_info;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_info;
|
||||
};
|
||||
|
||||
memory@00000000 {
|
||||
@ -91,6 +94,75 @@
|
||||
|
||||
&cp0_uart0 {
|
||||
status = "okay";
|
||||
|
||||
puzzle-mcu {
|
||||
compatible = "iei,wt61p803-puzzle";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
current-speed = <115200>;
|
||||
enable-beep;
|
||||
status = "okay";
|
||||
|
||||
leds {
|
||||
compatible = "iei,wt61p803-puzzle-leds";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "okay";
|
||||
|
||||
led@0 {
|
||||
reg = <0>;
|
||||
label = "white:network";
|
||||
active-low;
|
||||
};
|
||||
|
||||
led@1 {
|
||||
reg = <1>;
|
||||
label = "green:cloud";
|
||||
active-low;
|
||||
};
|
||||
|
||||
led_info: led@2 {
|
||||
reg = <2>;
|
||||
label = "orange:info";
|
||||
active-low;
|
||||
};
|
||||
|
||||
led_power: led@3 {
|
||||
reg = <3>;
|
||||
label = "yellow:power";
|
||||
active-low;
|
||||
default-state = "on";
|
||||
};
|
||||
};
|
||||
|
||||
hwmon {
|
||||
compatible = "iei,wt61p803-puzzle-hwmon";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
chassis_fan_group0: fan-group@0 {
|
||||
#cooling-cells = <2>;
|
||||
reg = <0x00>;
|
||||
cooling-levels = <64 102 170 230 250>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&ap_thermal_cpu1 {
|
||||
trips {
|
||||
cpu_active: cpu-active {
|
||||
temperature = <44000>;
|
||||
hysteresis = <2000>;
|
||||
type = "active";
|
||||
};
|
||||
};
|
||||
cooling-maps {
|
||||
fan-map {
|
||||
trip = <&cpu_active>;
|
||||
cooling-device = <&chassis_fan_group0 64 THERMAL_NO_LIMIT>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
/* on-board eMMC - U9 */
|
||||
|
||||
11
target/linux/mvebu/files/include/linux/mfd/puzzle.h
Normal file
11
target/linux/mvebu/files/include/linux/mfd/puzzle.h
Normal file
@ -0,0 +1,11 @@
|
||||
/* SPDX-License-Identifier: GPL-2.0+ */
|
||||
|
||||
#ifndef _LINUX_PUZZLE_H_
|
||||
#define _LINUX_PUZZLE_H_
|
||||
|
||||
struct puzzle;
|
||||
int puzzle_led(struct puzzle *pz, u8 ledn, u8 ledmode);
|
||||
int puzzle_fan(struct puzzle *pz, u8 speed);
|
||||
int puzzle_buzzer(struct puzzle *pz, u8 len);
|
||||
|
||||
#endif /* _LINUX_PUZZLE_H_ */
|
||||
@ -0,0 +1,218 @@
|
||||
From aa4a0ccc41997f2da172165c92803abace43bd1c Mon Sep 17 00:00:00 2001
|
||||
From: Luka Kovacic <luka.kovacic () sartura ! hr>
|
||||
Date: Tue, 24 Aug 2021 12:44:32 +0000
|
||||
Subject: [PATCH 1/7] dt-bindings: Add IEI vendor prefix and IEI WT61P803
|
||||
PUZZLE driver bindings
|
||||
|
||||
Add the IEI WT61P803 PUZZLE Device Tree bindings for MFD, HWMON and LED
|
||||
drivers. A new vendor prefix is also added accordingly for
|
||||
IEI Integration Corp.
|
||||
|
||||
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
Signed-off-by: Pavo Banicevic <pavo.banicevic@sartura.hr>
|
||||
Cc: Luka Perkov <luka.perkov@sartura.hr>
|
||||
Cc: Robert Marko <robert.marko@sartura.hr>
|
||||
---
|
||||
.../hwmon/iei,wt61p803-puzzle-hwmon.yaml | 53 ++++++++++++
|
||||
.../leds/iei,wt61p803-puzzle-leds.yaml | 39 +++++++++
|
||||
.../bindings/mfd/iei,wt61p803-puzzle.yaml | 82 +++++++++++++++++++
|
||||
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
|
||||
4 files changed, 176 insertions(+)
|
||||
create mode 100644 Documentation/devicetree/bindings/hwmon/iei,wt61p803-puzzle-hwmon.yaml
|
||||
create mode 100644 Documentation/devicetree/bindings/leds/iei,wt61p803-puzzle-leds.yaml
|
||||
create mode 100644 Documentation/devicetree/bindings/mfd/iei,wt61p803-puzzle.yaml
|
||||
|
||||
--- /dev/null
|
||||
+++ b/Documentation/devicetree/bindings/hwmon/iei,wt61p803-puzzle-hwmon.yaml
|
||||
@@ -0,0 +1,53 @@
|
||||
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
|
||||
+%YAML 1.2
|
||||
+---
|
||||
+$id: http://devicetree.org/schemas/hwmon/iei,wt61p803-puzzle-hwmon.yaml#
|
||||
+$schema: http://devicetree.org/meta-schemas/core.yaml#
|
||||
+
|
||||
+title: IEI WT61P803 PUZZLE MCU HWMON module from IEI Integration Corp.
|
||||
+
|
||||
+maintainers:
|
||||
+ - Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
+
|
||||
+description: |
|
||||
+ This module is a part of the IEI WT61P803 PUZZLE MFD device. For more details
|
||||
+ see Documentation/devicetree/bindings/mfd/iei,wt61p803-puzzle.yaml.
|
||||
+
|
||||
+ The HWMON module is a sub-node of the MCU node in the Device Tree.
|
||||
+
|
||||
+properties:
|
||||
+ compatible:
|
||||
+ const: iei,wt61p803-puzzle-hwmon
|
||||
+
|
||||
+ "#address-cells":
|
||||
+ const: 1
|
||||
+
|
||||
+ "#size-cells":
|
||||
+ const: 0
|
||||
+
|
||||
+patternProperties:
|
||||
+ "^fan-group@[0-1]$":
|
||||
+ type: object
|
||||
+ properties:
|
||||
+ reg:
|
||||
+ minimum: 0
|
||||
+ maximum: 1
|
||||
+ description:
|
||||
+ Fan group ID
|
||||
+
|
||||
+ cooling-levels:
|
||||
+ minItems: 1
|
||||
+ maxItems: 255
|
||||
+ description:
|
||||
+ Cooling levels for the fans (PWM value mapping)
|
||||
+ description: |
|
||||
+ Properties for each fan group.
|
||||
+ required:
|
||||
+ - reg
|
||||
+
|
||||
+required:
|
||||
+ - compatible
|
||||
+ - "#address-cells"
|
||||
+ - "#size-cells"
|
||||
+
|
||||
+additionalProperties: false
|
||||
--- /dev/null
|
||||
+++ b/Documentation/devicetree/bindings/leds/iei,wt61p803-puzzle-leds.yaml
|
||||
@@ -0,0 +1,39 @@
|
||||
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
|
||||
+%YAML 1.2
|
||||
+---
|
||||
+$id: http://devicetree.org/schemas/leds/iei,wt61p803-puzzle-leds.yaml#
|
||||
+$schema: http://devicetree.org/meta-schemas/core.yaml#
|
||||
+
|
||||
+title: IEI WT61P803 PUZZLE MCU LED module from IEI Integration Corp.
|
||||
+
|
||||
+maintainers:
|
||||
+ - Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
+
|
||||
+description: |
|
||||
+ This module is a part of the IEI WT61P803 PUZZLE MFD device. For more details
|
||||
+ see Documentation/devicetree/bindings/mfd/iei,wt61p803-puzzle.yaml.
|
||||
+
|
||||
+ The LED module is a sub-node of the MCU node in the Device Tree.
|
||||
+
|
||||
+properties:
|
||||
+ compatible:
|
||||
+ const: iei,wt61p803-puzzle-leds
|
||||
+
|
||||
+ "#address-cells":
|
||||
+ const: 1
|
||||
+
|
||||
+ "#size-cells":
|
||||
+ const: 0
|
||||
+
|
||||
+ led@0:
|
||||
+ type: object
|
||||
+ $ref: common.yaml
|
||||
+ description: |
|
||||
+ Properties for a single LED.
|
||||
+
|
||||
+required:
|
||||
+ - compatible
|
||||
+ - "#address-cells"
|
||||
+ - "#size-cells"
|
||||
+
|
||||
+additionalProperties: false
|
||||
--- /dev/null
|
||||
+++ b/Documentation/devicetree/bindings/mfd/iei,wt61p803-puzzle.yaml
|
||||
@@ -0,0 +1,82 @@
|
||||
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
|
||||
+%YAML 1.2
|
||||
+---
|
||||
+$id: http://devicetree.org/schemas/mfd/iei,wt61p803-puzzle.yaml#
|
||||
+$schema: http://devicetree.org/meta-schemas/core.yaml#
|
||||
+
|
||||
+title: IEI WT61P803 PUZZLE MCU from IEI Integration Corp.
|
||||
+
|
||||
+maintainers:
|
||||
+ - Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
+
|
||||
+description: |
|
||||
+ IEI WT61P803 PUZZLE MCU is embedded in some IEI Puzzle series boards.
|
||||
+ It's used for controlling system power states, fans, LEDs and temperature
|
||||
+ sensors.
|
||||
+
|
||||
+ For Device Tree bindings of other sub-modules (HWMON, LEDs) refer to the
|
||||
+ binding documents under the respective subsystem directories.
|
||||
+
|
||||
+properties:
|
||||
+ compatible:
|
||||
+ const: iei,wt61p803-puzzle
|
||||
+
|
||||
+ current-speed:
|
||||
+ description:
|
||||
+ Serial bus speed in bps
|
||||
+ maxItems: 1
|
||||
+
|
||||
+ enable-beep: true
|
||||
+
|
||||
+ hwmon:
|
||||
+ $ref: /schemas/hwmon/iei,wt61p803-puzzle-hwmon.yaml
|
||||
+
|
||||
+ leds:
|
||||
+ $ref: /schemas/leds/iei,wt61p803-puzzle-leds.yaml
|
||||
+
|
||||
+required:
|
||||
+ - compatible
|
||||
+ - current-speed
|
||||
+
|
||||
+additionalProperties: false
|
||||
+
|
||||
+examples:
|
||||
+ - |
|
||||
+ #include <dt-bindings/leds/common.h>
|
||||
+ serial {
|
||||
+ mcu {
|
||||
+ compatible = "iei,wt61p803-puzzle";
|
||||
+ current-speed = <115200>;
|
||||
+ enable-beep;
|
||||
+
|
||||
+ leds {
|
||||
+ compatible = "iei,wt61p803-puzzle-leds";
|
||||
+ #address-cells = <1>;
|
||||
+ #size-cells = <0>;
|
||||
+
|
||||
+ led@0 {
|
||||
+ reg = <0>;
|
||||
+ function = LED_FUNCTION_POWER;
|
||||
+ color = <LED_COLOR_ID_BLUE>;
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ hwmon {
|
||||
+ compatible = "iei,wt61p803-puzzle-hwmon";
|
||||
+ #address-cells = <1>;
|
||||
+ #size-cells = <0>;
|
||||
+
|
||||
+ fan-group@0 {
|
||||
+ #cooling-cells = <2>;
|
||||
+ reg = <0x00>;
|
||||
+ cooling-levels = <64 102 170 230 250>;
|
||||
+ };
|
||||
+
|
||||
+ fan-group@1 {
|
||||
+ #cooling-cells = <2>;
|
||||
+ reg = <0x01>;
|
||||
+ cooling-levels = <64 102 170 230 250>;
|
||||
+ };
|
||||
+ };
|
||||
+ };
|
||||
+ };
|
||||
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
|
||||
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
|
||||
@@ -475,6 +475,8 @@ patternProperties:
|
||||
description: IC Plus Corp.
|
||||
"^idt,.*":
|
||||
description: Integrated Device Technologies, Inc.
|
||||
+ "^iei,.*":
|
||||
+ description: IEI Integration Corp.
|
||||
"^ifi,.*":
|
||||
description: Ingenieurburo Fur Ic-Technologie (I/F/I)
|
||||
"^ilitek,.*":
|
||||
File diff suppressed because it is too large
Load Diff
@ -0,0 +1,469 @@
|
||||
From e3310a638cd310bfd93dbbc6d2732ab6aea18dd2 Mon Sep 17 00:00:00 2001
|
||||
From: Luka Kovacic <luka.kovacic () sartura ! hr>
|
||||
Date: Tue, 24 Aug 2021 12:44:34 +0000
|
||||
Subject: [PATCH 3/7] drivers: hwmon: Add the IEI WT61P803 PUZZLE HWMON driver
|
||||
|
||||
Add the IEI WT61P803 PUZZLE HWMON driver, that handles the fan speed
|
||||
control via PWM, reading fan speed and reading on-board temperature
|
||||
sensors.
|
||||
|
||||
The driver registers a HWMON device and a simple thermal cooling device to
|
||||
enable in-kernel fan management.
|
||||
|
||||
This driver depends on the IEI WT61P803 PUZZLE MFD driver.
|
||||
|
||||
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
Signed-off-by: Pavo Banicevic <pavo.banicevic@sartura.hr>
|
||||
Acked-by: Guenter Roeck <linux@roeck-us.net>
|
||||
Cc: Luka Perkov <luka.perkov@sartura.hr>
|
||||
Cc: Robert Marko <robert.marko@sartura.hr>
|
||||
---
|
||||
drivers/hwmon/Kconfig | 8 +
|
||||
drivers/hwmon/Makefile | 1 +
|
||||
drivers/hwmon/iei-wt61p803-puzzle-hwmon.c | 413 ++++++++++++++++++++++
|
||||
3 files changed, 422 insertions(+)
|
||||
create mode 100644 drivers/hwmon/iei-wt61p803-puzzle-hwmon.c
|
||||
|
||||
--- a/drivers/hwmon/Kconfig
|
||||
+++ b/drivers/hwmon/Kconfig
|
||||
@@ -722,6 +722,14 @@ config SENSORS_IBMPOWERNV
|
||||
This driver can also be built as a module. If so, the module
|
||||
will be called ibmpowernv.
|
||||
|
||||
+config SENSORS_IEI_WT61P803_PUZZLE_HWMON
|
||||
+ tristate "IEI WT61P803 PUZZLE MFD HWMON Driver"
|
||||
+ depends on MFD_IEI_WT61P803_PUZZLE
|
||||
+ help
|
||||
+ The IEI WT61P803 PUZZLE MFD HWMON Driver handles reading fan speed
|
||||
+ and writing fan PWM values. It also supports reading on-board
|
||||
+ temperature sensors.
|
||||
+
|
||||
config SENSORS_IIO_HWMON
|
||||
tristate "Hwmon driver that uses channels specified via iio maps"
|
||||
depends on IIO
|
||||
--- a/drivers/hwmon/Makefile
|
||||
+++ b/drivers/hwmon/Makefile
|
||||
@@ -83,6 +83,7 @@ obj-$(CONFIG_SENSORS_HIH6130) += hih6130
|
||||
obj-$(CONFIG_SENSORS_ULTRA45) += ultra45_env.o
|
||||
obj-$(CONFIG_SENSORS_I5500) += i5500_temp.o
|
||||
obj-$(CONFIG_SENSORS_I5K_AMB) += i5k_amb.o
|
||||
+obj-$(CONFIG_SENSORS_IEI_WT61P803_PUZZLE_HWMON) += iei-wt61p803-puzzle-hwmon.o
|
||||
obj-$(CONFIG_SENSORS_IBMAEM) += ibmaem.o
|
||||
obj-$(CONFIG_SENSORS_IBMPEX) += ibmpex.o
|
||||
obj-$(CONFIG_SENSORS_IBMPOWERNV)+= ibmpowernv.o
|
||||
--- /dev/null
|
||||
+++ b/drivers/hwmon/iei-wt61p803-puzzle-hwmon.c
|
||||
@@ -0,0 +1,413 @@
|
||||
+// SPDX-License-Identifier: GPL-2.0-only
|
||||
+/* IEI WT61P803 PUZZLE MCU HWMON Driver
|
||||
+ *
|
||||
+ * Copyright (C) 2020 Sartura Ltd.
|
||||
+ * Author: Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
+ */
|
||||
+
|
||||
+#include <linux/err.h>
|
||||
+#include <linux/hwmon.h>
|
||||
+#include <linux/interrupt.h>
|
||||
+#include <linux/irq.h>
|
||||
+#include <linux/math64.h>
|
||||
+#include <linux/mfd/iei-wt61p803-puzzle.h>
|
||||
+#include <linux/mod_devicetable.h>
|
||||
+#include <linux/module.h>
|
||||
+#include <linux/platform_device.h>
|
||||
+#include <linux/property.h>
|
||||
+#include <linux/slab.h>
|
||||
+#include <linux/thermal.h>
|
||||
+
|
||||
+#define IEI_WT61P803_PUZZLE_HWMON_MAX_PWM 2
|
||||
+#define IEI_WT61P803_PUZZLE_HWMON_MAX_PWM_VAL 255
|
||||
+
|
||||
+/**
|
||||
+ * struct iei_wt61p803_puzzle_thermal_cooling_device - Thermal cooling device instance
|
||||
+ * @mcu_hwmon: Parent driver struct pointer
|
||||
+ * @tcdev: Thermal cooling device pointer
|
||||
+ * @name: Thermal cooling device name
|
||||
+ * @pwm_channel: Controlled PWM channel (0 or 1)
|
||||
+ * @cooling_levels: Thermal cooling device cooling levels (DT)
|
||||
+ */
|
||||
+struct iei_wt61p803_puzzle_thermal_cooling_device {
|
||||
+ struct iei_wt61p803_puzzle_hwmon *mcu_hwmon;
|
||||
+ struct thermal_cooling_device *tcdev;
|
||||
+ char name[THERMAL_NAME_LENGTH];
|
||||
+ int pwm_channel;
|
||||
+ u8 *cooling_levels;
|
||||
+};
|
||||
+
|
||||
+/**
|
||||
+ * struct iei_wt61p803_puzzle_hwmon - MCU HWMON Driver
|
||||
+ * @mcu: MCU struct pointer
|
||||
+ * @response_buffer Global MCU response buffer
|
||||
+ * @thermal_cooling_dev_present: Per-channel thermal cooling device control indicator
|
||||
+ * @cdev: Per-channel thermal cooling device private structure
|
||||
+ */
|
||||
+struct iei_wt61p803_puzzle_hwmon {
|
||||
+ struct iei_wt61p803_puzzle *mcu;
|
||||
+ unsigned char response_buffer[IEI_WT61P803_PUZZLE_BUF_SIZE];
|
||||
+ bool thermal_cooling_dev_present[IEI_WT61P803_PUZZLE_HWMON_MAX_PWM];
|
||||
+ struct iei_wt61p803_puzzle_thermal_cooling_device
|
||||
+ *cdev[IEI_WT61P803_PUZZLE_HWMON_MAX_PWM];
|
||||
+ struct mutex lock; /* mutex to protect response_buffer array */
|
||||
+};
|
||||
+
|
||||
+#define raw_temp_to_milidegree_celsius(x) (((x) - 0x80) * 1000)
|
||||
+static int iei_wt61p803_puzzle_read_temp_sensor(struct iei_wt61p803_puzzle_hwmon *mcu_hwmon,
|
||||
+ int channel, long *value)
|
||||
+{
|
||||
+ unsigned char *resp_buf = mcu_hwmon->response_buffer;
|
||||
+ unsigned char temp_sensor_ntc_cmd[4] = {
|
||||
+ IEI_WT61P803_PUZZLE_CMD_HEADER_START,
|
||||
+ IEI_WT61P803_PUZZLE_CMD_TEMP,
|
||||
+ IEI_WT61P803_PUZZLE_CMD_TEMP_ALL,
|
||||
+ };
|
||||
+ size_t reply_size;
|
||||
+ int ret;
|
||||
+
|
||||
+ mutex_lock(&mcu_hwmon->lock);
|
||||
+ ret = iei_wt61p803_puzzle_write_command(mcu_hwmon->mcu, temp_sensor_ntc_cmd,
|
||||
+ sizeof(temp_sensor_ntc_cmd), resp_buf,
|
||||
+ &reply_size);
|
||||
+ if (ret)
|
||||
+ goto exit;
|
||||
+
|
||||
+ if (reply_size != 7) {
|
||||
+ ret = -EIO;
|
||||
+ goto exit;
|
||||
+ }
|
||||
+
|
||||
+ /* Check the number of NTC values */
|
||||
+ if (resp_buf[3] != '2') {
|
||||
+ ret = -EIO;
|
||||
+ goto exit;
|
||||
+ }
|
||||
+
|
||||
+ *value = raw_temp_to_milidegree_celsius(resp_buf[4 + channel]);
|
||||
+exit:
|
||||
+ mutex_unlock(&mcu_hwmon->lock);
|
||||
+ return ret;
|
||||
+}
|
||||
+
|
||||
+#define raw_fan_val_to_rpm(x, y) ((((x) << 8 | (y)) / 2) * 60)
|
||||
+static int iei_wt61p803_puzzle_read_fan_speed(struct iei_wt61p803_puzzle_hwmon *mcu_hwmon,
|
||||
+ int channel, long *value)
|
||||
+{
|
||||
+ unsigned char *resp_buf = mcu_hwmon->response_buffer;
|
||||
+ unsigned char fan_speed_cmd[4] = {};
|
||||
+ size_t reply_size;
|
||||
+ int ret;
|
||||
+
|
||||
+ fan_speed_cmd[0] = IEI_WT61P803_PUZZLE_CMD_HEADER_START;
|
||||
+ fan_speed_cmd[1] = IEI_WT61P803_PUZZLE_CMD_FAN;
|
||||
+ fan_speed_cmd[2] = IEI_WT61P803_PUZZLE_CMD_FAN_RPM(channel);
|
||||
+
|
||||
+ mutex_lock(&mcu_hwmon->lock);
|
||||
+ ret = iei_wt61p803_puzzle_write_command(mcu_hwmon->mcu, fan_speed_cmd,
|
||||
+ sizeof(fan_speed_cmd), resp_buf,
|
||||
+ &reply_size);
|
||||
+ if (ret)
|
||||
+ goto exit;
|
||||
+
|
||||
+ if (reply_size != 7) {
|
||||
+ ret = -EIO;
|
||||
+ goto exit;
|
||||
+ }
|
||||
+
|
||||
+ *value = raw_fan_val_to_rpm(resp_buf[3], resp_buf[4]);
|
||||
+exit:
|
||||
+ mutex_unlock(&mcu_hwmon->lock);
|
||||
+ return ret;
|
||||
+}
|
||||
+
|
||||
+static int iei_wt61p803_puzzle_write_pwm_channel(struct iei_wt61p803_puzzle_hwmon *mcu_hwmon,
|
||||
+ int channel, long pwm_set_val)
|
||||
+{
|
||||
+ unsigned char *resp_buf = mcu_hwmon->response_buffer;
|
||||
+ unsigned char pwm_set_cmd[6] = {};
|
||||
+ size_t reply_size;
|
||||
+ int ret;
|
||||
+
|
||||
+ pwm_set_cmd[0] = IEI_WT61P803_PUZZLE_CMD_HEADER_START;
|
||||
+ pwm_set_cmd[1] = IEI_WT61P803_PUZZLE_CMD_FAN;
|
||||
+ pwm_set_cmd[2] = IEI_WT61P803_PUZZLE_CMD_FAN_PWM_WRITE;
|
||||
+ pwm_set_cmd[3] = IEI_WT61P803_PUZZLE_CMD_FAN_PWM(channel);
|
||||
+ pwm_set_cmd[4] = pwm_set_val;
|
||||
+
|
||||
+ mutex_lock(&mcu_hwmon->lock);
|
||||
+ ret = iei_wt61p803_puzzle_write_command(mcu_hwmon->mcu, pwm_set_cmd,
|
||||
+ sizeof(pwm_set_cmd), resp_buf,
|
||||
+ &reply_size);
|
||||
+ if (ret)
|
||||
+ goto exit;
|
||||
+
|
||||
+ if (reply_size != 3) {
|
||||
+ ret = -EIO;
|
||||
+ goto exit;
|
||||
+ }
|
||||
+
|
||||
+ if (!(resp_buf[0] == IEI_WT61P803_PUZZLE_CMD_HEADER_START &&
|
||||
+ resp_buf[1] == IEI_WT61P803_PUZZLE_CMD_RESPONSE_OK &&
|
||||
+ resp_buf[2] == IEI_WT61P803_PUZZLE_CHECKSUM_RESPONSE_OK)) {
|
||||
+ ret = -EIO;
|
||||
+ goto exit;
|
||||
+ }
|
||||
+exit:
|
||||
+ mutex_unlock(&mcu_hwmon->lock);
|
||||
+ return ret;
|
||||
+}
|
||||
+
|
||||
+static int iei_wt61p803_puzzle_read_pwm_channel(struct iei_wt61p803_puzzle_hwmon *mcu_hwmon,
|
||||
+ int channel, long *value)
|
||||
+{
|
||||
+ unsigned char *resp_buf = mcu_hwmon->response_buffer;
|
||||
+ unsigned char pwm_get_cmd[5] = {};
|
||||
+ size_t reply_size;
|
||||
+ int ret;
|
||||
+
|
||||
+ pwm_get_cmd[0] = IEI_WT61P803_PUZZLE_CMD_HEADER_START;
|
||||
+ pwm_get_cmd[1] = IEI_WT61P803_PUZZLE_CMD_FAN;
|
||||
+ pwm_get_cmd[2] = IEI_WT61P803_PUZZLE_CMD_FAN_PWM_READ;
|
||||
+ pwm_get_cmd[3] = IEI_WT61P803_PUZZLE_CMD_FAN_PWM(channel);
|
||||
+
|
||||
+ ret = iei_wt61p803_puzzle_write_command(mcu_hwmon->mcu, pwm_get_cmd,
|
||||
+ sizeof(pwm_get_cmd), resp_buf,
|
||||
+ &reply_size);
|
||||
+ if (ret)
|
||||
+ return ret;
|
||||
+
|
||||
+ if (reply_size != 5)
|
||||
+ return -EIO;
|
||||
+
|
||||
+ if (resp_buf[2] != IEI_WT61P803_PUZZLE_CMD_FAN_PWM_READ)
|
||||
+ return -EIO;
|
||||
+
|
||||
+ *value = resp_buf[3];
|
||||
+
|
||||
+ return 0;
|
||||
+}
|
||||
+
|
||||
+static int iei_wt61p803_puzzle_read(struct device *dev, enum hwmon_sensor_types type,
|
||||
+ u32 attr, int channel, long *val)
|
||||
+{
|
||||
+ struct iei_wt61p803_puzzle_hwmon *mcu_hwmon = dev_get_drvdata(dev->parent);
|
||||
+
|
||||
+ switch (type) {
|
||||
+ case hwmon_pwm:
|
||||
+ return iei_wt61p803_puzzle_read_pwm_channel(mcu_hwmon, channel, val);
|
||||
+ case hwmon_fan:
|
||||
+ return iei_wt61p803_puzzle_read_fan_speed(mcu_hwmon, channel, val);
|
||||
+ case hwmon_temp:
|
||||
+ return iei_wt61p803_puzzle_read_temp_sensor(mcu_hwmon, channel, val);
|
||||
+ default:
|
||||
+ return -EINVAL;
|
||||
+ }
|
||||
+}
|
||||
+
|
||||
+static int iei_wt61p803_puzzle_write(struct device *dev, enum hwmon_sensor_types type,
|
||||
+ u32 attr, int channel, long val)
|
||||
+{
|
||||
+ struct iei_wt61p803_puzzle_hwmon *mcu_hwmon = dev_get_drvdata(dev->parent);
|
||||
+
|
||||
+ return iei_wt61p803_puzzle_write_pwm_channel(mcu_hwmon, channel, val);
|
||||
+}
|
||||
+
|
||||
+static umode_t iei_wt61p803_puzzle_is_visible(const void *data, enum hwmon_sensor_types type,
|
||||
+ u32 attr, int channel)
|
||||
+{
|
||||
+ const struct iei_wt61p803_puzzle_hwmon *mcu_hwmon = data;
|
||||
+
|
||||
+ switch (type) {
|
||||
+ case hwmon_pwm:
|
||||
+ if (mcu_hwmon->thermal_cooling_dev_present[channel])
|
||||
+ return 0444;
|
||||
+ if (attr == hwmon_pwm_input)
|
||||
+ return 0644;
|
||||
+ break;
|
||||
+ case hwmon_fan:
|
||||
+ if (attr == hwmon_fan_input)
|
||||
+ return 0444;
|
||||
+ break;
|
||||
+ case hwmon_temp:
|
||||
+ if (attr == hwmon_temp_input)
|
||||
+ return 0444;
|
||||
+ break;
|
||||
+ default:
|
||||
+ return 0;
|
||||
+ }
|
||||
+
|
||||
+ return 0;
|
||||
+}
|
||||
+
|
||||
+static const struct hwmon_ops iei_wt61p803_puzzle_hwmon_ops = {
|
||||
+ .is_visible = iei_wt61p803_puzzle_is_visible,
|
||||
+ .read = iei_wt61p803_puzzle_read,
|
||||
+ .write = iei_wt61p803_puzzle_write,
|
||||
+};
|
||||
+
|
||||
+static const struct hwmon_channel_info *iei_wt61p803_puzzle_info[] = {
|
||||
+ HWMON_CHANNEL_INFO(pwm,
|
||||
+ HWMON_PWM_INPUT,
|
||||
+ HWMON_PWM_INPUT),
|
||||
+ HWMON_CHANNEL_INFO(fan,
|
||||
+ HWMON_F_INPUT,
|
||||
+ HWMON_F_INPUT,
|
||||
+ HWMON_F_INPUT,
|
||||
+ HWMON_F_INPUT,
|
||||
+ HWMON_F_INPUT),
|
||||
+ HWMON_CHANNEL_INFO(temp,
|
||||
+ HWMON_T_INPUT,
|
||||
+ HWMON_T_INPUT),
|
||||
+ NULL
|
||||
+};
|
||||
+
|
||||
+static const struct hwmon_chip_info iei_wt61p803_puzzle_chip_info = {
|
||||
+ .ops = &iei_wt61p803_puzzle_hwmon_ops,
|
||||
+ .info = iei_wt61p803_puzzle_info,
|
||||
+};
|
||||
+
|
||||
+static int iei_wt61p803_puzzle_get_max_state(struct thermal_cooling_device *tcdev,
|
||||
+ unsigned long *state)
|
||||
+{
|
||||
+ *state = IEI_WT61P803_PUZZLE_HWMON_MAX_PWM_VAL;
|
||||
+
|
||||
+ return 0;
|
||||
+}
|
||||
+
|
||||
+static int iei_wt61p803_puzzle_get_cur_state(struct thermal_cooling_device *tcdev,
|
||||
+ unsigned long *state)
|
||||
+{
|
||||
+ struct iei_wt61p803_puzzle_thermal_cooling_device *cdev = tcdev->devdata;
|
||||
+ struct iei_wt61p803_puzzle_hwmon *mcu_hwmon = cdev->mcu_hwmon;
|
||||
+ long value;
|
||||
+ int ret;
|
||||
+
|
||||
+ ret = iei_wt61p803_puzzle_read_pwm_channel(mcu_hwmon, cdev->pwm_channel, &value);
|
||||
+ if (ret)
|
||||
+ return ret;
|
||||
+ *state = value;
|
||||
+ return 0;
|
||||
+}
|
||||
+
|
||||
+static int iei_wt61p803_puzzle_set_cur_state(struct thermal_cooling_device *tcdev,
|
||||
+ unsigned long state)
|
||||
+{
|
||||
+ struct iei_wt61p803_puzzle_thermal_cooling_device *cdev = tcdev->devdata;
|
||||
+ struct iei_wt61p803_puzzle_hwmon *mcu_hwmon = cdev->mcu_hwmon;
|
||||
+
|
||||
+ return iei_wt61p803_puzzle_write_pwm_channel(mcu_hwmon, cdev->pwm_channel, state);
|
||||
+}
|
||||
+
|
||||
+static const struct thermal_cooling_device_ops iei_wt61p803_puzzle_cooling_ops = {
|
||||
+ .get_max_state = iei_wt61p803_puzzle_get_max_state,
|
||||
+ .get_cur_state = iei_wt61p803_puzzle_get_cur_state,
|
||||
+ .set_cur_state = iei_wt61p803_puzzle_set_cur_state,
|
||||
+};
|
||||
+
|
||||
+static int
|
||||
+iei_wt61p803_puzzle_enable_thermal_cooling_dev(struct device *dev,
|
||||
+ struct fwnode_handle *child,
|
||||
+ struct iei_wt61p803_puzzle_hwmon *mcu_hwmon)
|
||||
+{
|
||||
+ struct iei_wt61p803_puzzle_thermal_cooling_device *cdev;
|
||||
+ u32 pwm_channel;
|
||||
+ u8 num_levels;
|
||||
+ int ret;
|
||||
+
|
||||
+ ret = fwnode_property_read_u32(child, "reg", &pwm_channel);
|
||||
+ if (ret)
|
||||
+ return ret;
|
||||
+
|
||||
+ mcu_hwmon->thermal_cooling_dev_present[pwm_channel] = true;
|
||||
+
|
||||
+ num_levels = fwnode_property_count_u8(child, "cooling-levels");
|
||||
+ if (!num_levels)
|
||||
+ return -EINVAL;
|
||||
+
|
||||
+ cdev = devm_kzalloc(dev, sizeof(*cdev), GFP_KERNEL);
|
||||
+ if (!cdev)
|
||||
+ return -ENOMEM;
|
||||
+
|
||||
+ cdev->cooling_levels = devm_kmalloc_array(dev, num_levels, sizeof(u8), GFP_KERNEL);
|
||||
+ if (!cdev->cooling_levels)
|
||||
+ return -ENOMEM;
|
||||
+
|
||||
+ ret = fwnode_property_read_u8_array(child, "cooling-levels",
|
||||
+ cdev->cooling_levels,
|
||||
+ num_levels);
|
||||
+ if (ret) {
|
||||
+ dev_err(dev, "Couldn't read property 'cooling-levels'\n");
|
||||
+ return ret;
|
||||
+ }
|
||||
+
|
||||
+ snprintf(cdev->name, THERMAL_NAME_LENGTH, "wt61p803_puzzle_%d", pwm_channel);
|
||||
+ cdev->tcdev = devm_thermal_of_cooling_device_register(dev, NULL, cdev->name, cdev,
|
||||
+ &iei_wt61p803_puzzle_cooling_ops);
|
||||
+ if (IS_ERR(cdev->tcdev))
|
||||
+ return PTR_ERR(cdev->tcdev);
|
||||
+
|
||||
+ cdev->mcu_hwmon = mcu_hwmon;
|
||||
+ cdev->pwm_channel = pwm_channel;
|
||||
+ mcu_hwmon->cdev[pwm_channel] = cdev;
|
||||
+
|
||||
+ return 0;
|
||||
+}
|
||||
+
|
||||
+static int iei_wt61p803_puzzle_hwmon_probe(struct platform_device *pdev)
|
||||
+{
|
||||
+ struct device *dev = &pdev->dev;
|
||||
+ struct iei_wt61p803_puzzle *mcu = dev_get_drvdata(dev->parent);
|
||||
+ struct iei_wt61p803_puzzle_hwmon *mcu_hwmon;
|
||||
+ struct fwnode_handle *child;
|
||||
+ struct device *hwmon_dev;
|
||||
+ int ret;
|
||||
+
|
||||
+ mcu_hwmon = devm_kzalloc(dev, sizeof(*mcu_hwmon), GFP_KERNEL);
|
||||
+ if (!mcu_hwmon)
|
||||
+ return -ENOMEM;
|
||||
+
|
||||
+ mcu_hwmon->mcu = mcu;
|
||||
+ platform_set_drvdata(pdev, mcu_hwmon);
|
||||
+ mutex_init(&mcu_hwmon->lock);
|
||||
+
|
||||
+ hwmon_dev = devm_hwmon_device_register_with_info(dev, "iei_wt61p803_puzzle",
|
||||
+ mcu_hwmon,
|
||||
+ &iei_wt61p803_puzzle_chip_info,
|
||||
+ NULL);
|
||||
+ if (IS_ERR(hwmon_dev))
|
||||
+ return PTR_ERR(hwmon_dev);
|
||||
+
|
||||
+ /* Control fans via PWM lines via Linux Kernel */
|
||||
+ if (IS_ENABLED(CONFIG_THERMAL)) {
|
||||
+ device_for_each_child_node(dev, child) {
|
||||
+ ret = iei_wt61p803_puzzle_enable_thermal_cooling_dev(dev, child, mcu_hwmon);
|
||||
+ if (ret) {
|
||||
+ dev_err(dev, "Enabling the PWM fan failed\n");
|
||||
+ fwnode_handle_put(child);
|
||||
+ return ret;
|
||||
+ }
|
||||
+ }
|
||||
+ }
|
||||
+ return 0;
|
||||
+}
|
||||
+
|
||||
+static const struct of_device_id iei_wt61p803_puzzle_hwmon_id_table[] = {
|
||||
+ { .compatible = "iei,wt61p803-puzzle-hwmon" },
|
||||
+ {}
|
||||
+};
|
||||
+MODULE_DEVICE_TABLE(of, iei_wt61p803_puzzle_hwmon_id_table);
|
||||
+
|
||||
+static struct platform_driver iei_wt61p803_puzzle_hwmon_driver = {
|
||||
+ .driver = {
|
||||
+ .name = "iei-wt61p803-puzzle-hwmon",
|
||||
+ .of_match_table = iei_wt61p803_puzzle_hwmon_id_table,
|
||||
+ },
|
||||
+ .probe = iei_wt61p803_puzzle_hwmon_probe,
|
||||
+};
|
||||
+
|
||||
+module_platform_driver(iei_wt61p803_puzzle_hwmon_driver);
|
||||
+
|
||||
+MODULE_DESCRIPTION("IEI WT61P803 PUZZLE MCU HWMON Driver");
|
||||
+MODULE_AUTHOR("Luka Kovacic <luka.kovacic@sartura.hr>");
|
||||
+MODULE_LICENSE("GPL v2");
|
||||
@ -0,0 +1,207 @@
|
||||
From f3b44eb69cc561cf05d00506dcec0dd9be003ed8 Mon Sep 17 00:00:00 2001
|
||||
From: Luka Kovacic <luka.kovacic () sartura ! hr>
|
||||
Date: Tue, 24 Aug 2021 12:44:35 +0000
|
||||
Subject: [PATCH 4/7] drivers: leds: Add the IEI WT61P803 PUZZLE LED driver
|
||||
|
||||
Add support for the IEI WT61P803 PUZZLE LED driver.
|
||||
Currently only the front panel power LED is supported,
|
||||
since it is the only LED on this board wired through the
|
||||
MCU.
|
||||
|
||||
The LED is wired directly to the on-board MCU controller
|
||||
and is toggled using an MCU command.
|
||||
|
||||
Support for more LEDs is going to be added in case more
|
||||
boards implement this microcontroller, as LEDs use many
|
||||
different GPIOs.
|
||||
|
||||
This driver depends on the IEI WT61P803 PUZZLE MFD driver.
|
||||
|
||||
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
Signed-off-by: Pavo Banicevic <pavo.banicevic@sartura.hr>
|
||||
Cc: Luka Perkov <luka.perkov@sartura.hr>
|
||||
Cc: Robert Marko <robert.marko@sartura.hr>
|
||||
---
|
||||
drivers/leds/Kconfig | 8 ++
|
||||
drivers/leds/Makefile | 1 +
|
||||
drivers/leds/leds-iei-wt61p803-puzzle.c | 147 ++++++++++++++++++++++++
|
||||
3 files changed, 156 insertions(+)
|
||||
create mode 100644 drivers/leds/leds-iei-wt61p803-puzzle.c
|
||||
|
||||
--- a/drivers/leds/Kconfig
|
||||
+++ b/drivers/leds/Kconfig
|
||||
@@ -333,6 +333,14 @@ config LEDS_IPAQ_MICRO
|
||||
Choose this option if you want to use the notification LED on
|
||||
Compaq/HP iPAQ h3100 and h3600.
|
||||
|
||||
+config LEDS_IEI_WT61P803_PUZZLE
|
||||
+ tristate "LED Support for the IEI WT61P803 PUZZLE MCU"
|
||||
+ depends on LEDS_CLASS
|
||||
+ depends on MFD_IEI_WT61P803_PUZZLE
|
||||
+ help
|
||||
+ This option enables support for LEDs controlled by the IEI WT61P803
|
||||
+ M801 MCU.
|
||||
+
|
||||
config LEDS_HP6XX
|
||||
tristate "LED Support for the HP Jornada 6xx"
|
||||
depends on LEDS_CLASS
|
||||
--- a/drivers/leds/Makefile
|
||||
+++ b/drivers/leds/Makefile
|
||||
@@ -35,6 +35,7 @@ obj-$(CONFIG_LEDS_HP6XX) += leds-hp6xx.
|
||||
obj-$(CONFIG_LEDS_INTEL_SS4200) += leds-ss4200.o
|
||||
obj-$(CONFIG_LEDS_IP30) += leds-ip30.o
|
||||
obj-$(CONFIG_LEDS_IPAQ_MICRO) += leds-ipaq-micro.o
|
||||
+obj-$(CONFIG_LEDS_IEI_WT61P803_PUZZLE) += leds-iei-wt61p803-puzzle.o
|
||||
obj-$(CONFIG_LEDS_IS31FL319X) += leds-is31fl319x.o
|
||||
obj-$(CONFIG_LEDS_IS31FL32XX) += leds-is31fl32xx.o
|
||||
obj-$(CONFIG_LEDS_KTD2692) += leds-ktd2692.o
|
||||
--- /dev/null
|
||||
+++ b/drivers/leds/leds-iei-wt61p803-puzzle.c
|
||||
@@ -0,0 +1,147 @@
|
||||
+// SPDX-License-Identifier: GPL-2.0-only
|
||||
+/* IEI WT61P803 PUZZLE MCU LED Driver
|
||||
+ *
|
||||
+ * Copyright (C) 2020 Sartura Ltd.
|
||||
+ * Author: Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
+ */
|
||||
+
|
||||
+#include <linux/leds.h>
|
||||
+#include <linux/mfd/iei-wt61p803-puzzle.h>
|
||||
+#include <linux/mod_devicetable.h>
|
||||
+#include <linux/module.h>
|
||||
+#include <linux/platform_device.h>
|
||||
+#include <linux/property.h>
|
||||
+#include <linux/slab.h>
|
||||
+
|
||||
+enum iei_wt61p803_puzzle_led_state {
|
||||
+ IEI_LED_OFF = 0x30,
|
||||
+ IEI_LED_ON = 0x31,
|
||||
+ IEI_LED_BLINK_5HZ = 0x32,
|
||||
+ IEI_LED_BLINK_1HZ = 0x33,
|
||||
+};
|
||||
+
|
||||
+/**
|
||||
+ * struct iei_wt61p803_puzzle_led - MCU LED Driver
|
||||
+ * @cdev: LED classdev
|
||||
+ * @mcu: MCU struct pointer
|
||||
+ * @response_buffer Global MCU response buffer
|
||||
+ * @lock: General mutex lock to protect simultaneous R/W access to led_power_state
|
||||
+ * @led_power_state: State of the front panel power LED
|
||||
+ */
|
||||
+struct iei_wt61p803_puzzle_led {
|
||||
+ struct led_classdev cdev;
|
||||
+ struct iei_wt61p803_puzzle *mcu;
|
||||
+ unsigned char response_buffer[IEI_WT61P803_PUZZLE_BUF_SIZE];
|
||||
+ struct mutex lock; /* mutex to protect led_power_state */
|
||||
+ int led_power_state;
|
||||
+};
|
||||
+
|
||||
+static inline struct iei_wt61p803_puzzle_led *cdev_to_iei_wt61p803_puzzle_led
|
||||
+ (struct led_classdev *led_cdev)
|
||||
+{
|
||||
+ return container_of(led_cdev, struct iei_wt61p803_puzzle_led, cdev);
|
||||
+}
|
||||
+
|
||||
+static int iei_wt61p803_puzzle_led_brightness_set_blocking(struct led_classdev *cdev,
|
||||
+ enum led_brightness brightness)
|
||||
+{
|
||||
+ struct iei_wt61p803_puzzle_led *priv = cdev_to_iei_wt61p803_puzzle_led(cdev);
|
||||
+ unsigned char *resp_buf = priv->response_buffer;
|
||||
+ unsigned char led_power_cmd[5] = {};
|
||||
+ size_t reply_size;
|
||||
+ int ret;
|
||||
+
|
||||
+ led_power_cmd[0] = IEI_WT61P803_PUZZLE_CMD_HEADER_START;
|
||||
+ led_power_cmd[1] = IEI_WT61P803_PUZZLE_CMD_LED;
|
||||
+ led_power_cmd[2] = IEI_WT61P803_PUZZLE_CMD_LED_POWER;
|
||||
+ led_power_cmd[3] = brightness == LED_OFF ? IEI_LED_OFF : IEI_LED_ON;
|
||||
+
|
||||
+ ret = iei_wt61p803_puzzle_write_command(priv->mcu, led_power_cmd,
|
||||
+ sizeof(led_power_cmd),
|
||||
+ resp_buf,
|
||||
+ &reply_size);
|
||||
+ if (ret)
|
||||
+ return ret;
|
||||
+
|
||||
+ if (reply_size != 3)
|
||||
+ return -EIO;
|
||||
+
|
||||
+ if (!(resp_buf[0] == IEI_WT61P803_PUZZLE_CMD_HEADER_START &&
|
||||
+ resp_buf[1] == IEI_WT61P803_PUZZLE_CMD_RESPONSE_OK &&
|
||||
+ resp_buf[2] == IEI_WT61P803_PUZZLE_CHECKSUM_RESPONSE_OK))
|
||||
+ return -EIO;
|
||||
+
|
||||
+ mutex_lock(&priv->lock);
|
||||
+ priv->led_power_state = brightness;
|
||||
+ mutex_unlock(&priv->lock);
|
||||
+
|
||||
+ return 0;
|
||||
+}
|
||||
+
|
||||
+static enum led_brightness iei_wt61p803_puzzle_led_brightness_get(struct led_classdev *cdev)
|
||||
+{
|
||||
+ struct iei_wt61p803_puzzle_led *priv = cdev_to_iei_wt61p803_puzzle_led(cdev);
|
||||
+ int led_state;
|
||||
+
|
||||
+ mutex_lock(&priv->lock);
|
||||
+ led_state = priv->led_power_state;
|
||||
+ mutex_unlock(&priv->lock);
|
||||
+
|
||||
+ return led_state;
|
||||
+}
|
||||
+
|
||||
+static int iei_wt61p803_puzzle_led_probe(struct platform_device *pdev)
|
||||
+{
|
||||
+ struct device *dev = &pdev->dev;
|
||||
+ struct iei_wt61p803_puzzle *mcu = dev_get_drvdata(dev->parent);
|
||||
+ struct iei_wt61p803_puzzle_led *priv;
|
||||
+ struct led_init_data init_data = {};
|
||||
+ struct fwnode_handle *child;
|
||||
+ int ret;
|
||||
+
|
||||
+ if (device_get_child_node_count(dev) != 1)
|
||||
+ return -EINVAL;
|
||||
+
|
||||
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
|
||||
+ if (!priv)
|
||||
+ return -ENOMEM;
|
||||
+
|
||||
+ priv->mcu = mcu;
|
||||
+ priv->led_power_state = 1;
|
||||
+ mutex_init(&priv->lock);
|
||||
+ dev_set_drvdata(dev, priv);
|
||||
+
|
||||
+ child = device_get_next_child_node(dev, NULL);
|
||||
+ init_data.fwnode = child;
|
||||
+
|
||||
+ priv->cdev.brightness_set_blocking = iei_wt61p803_puzzle_led_brightness_set_blocking;
|
||||
+ priv->cdev.brightness_get = iei_wt61p803_puzzle_led_brightness_get;
|
||||
+ priv->cdev.max_brightness = 1;
|
||||
+
|
||||
+ ret = devm_led_classdev_register_ext(dev, &priv->cdev, &init_data);
|
||||
+ if (ret)
|
||||
+ dev_err(dev, "Could not register LED\n");
|
||||
+
|
||||
+ fwnode_handle_put(child);
|
||||
+ return ret;
|
||||
+}
|
||||
+
|
||||
+static const struct of_device_id iei_wt61p803_puzzle_led_of_match[] = {
|
||||
+ { .compatible = "iei,wt61p803-puzzle-leds" },
|
||||
+ { }
|
||||
+};
|
||||
+MODULE_DEVICE_TABLE(of, iei_wt61p803_puzzle_led_of_match);
|
||||
+
|
||||
+static struct platform_driver iei_wt61p803_puzzle_led_driver = {
|
||||
+ .driver = {
|
||||
+ .name = "iei-wt61p803-puzzle-led",
|
||||
+ .of_match_table = iei_wt61p803_puzzle_led_of_match,
|
||||
+ },
|
||||
+ .probe = iei_wt61p803_puzzle_led_probe,
|
||||
+};
|
||||
+module_platform_driver(iei_wt61p803_puzzle_led_driver);
|
||||
+
|
||||
+MODULE_DESCRIPTION("IEI WT61P803 PUZZLE front panel LED driver");
|
||||
+MODULE_AUTHOR("Luka Kovacic <luka.kovacic@sartura.hr>");
|
||||
+MODULE_LICENSE("GPL v2");
|
||||
+MODULE_ALIAS("platform:leds-iei-wt61p803-puzzle");
|
||||
@ -0,0 +1,82 @@
|
||||
From 2fab3b4956c5b2f83c1e1abffc1df39de2933d83 Mon Sep 17 00:00:00 2001
|
||||
From: Luka Kovacic <luka.kovacic () sartura ! hr>
|
||||
Date: Tue, 24 Aug 2021 12:44:36 +0000
|
||||
Subject: [PATCH 5/7] Documentation/ABI: Add iei-wt61p803-puzzle driver sysfs
|
||||
interface documentation
|
||||
|
||||
Add the iei-wt61p803-puzzle driver sysfs interface documentation to allow
|
||||
monitoring and control of the microcontroller from user space.
|
||||
|
||||
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
Signed-off-by: Pavo Banicevic <pavo.banicevic@sartura.hr>
|
||||
Cc: Luka Perkov <luka.perkov@sartura.hr>
|
||||
Cc: Robert Marko <robert.marko@sartura.hr>
|
||||
---
|
||||
.../testing/sysfs-driver-iei-wt61p803-puzzle | 61 +++++++++++++++++++
|
||||
1 file changed, 61 insertions(+)
|
||||
create mode 100644 Documentation/ABI/testing/sysfs-driver-iei-wt61p803-puzzle
|
||||
|
||||
--- /dev/null
|
||||
+++ b/Documentation/ABI/testing/sysfs-driver-iei-wt61p803-puzzle
|
||||
@@ -0,0 +1,61 @@
|
||||
+What: /sys/bus/serial/devices/.../mac_address_*
|
||||
+Date: September 2020
|
||||
+Contact: Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
+Description: (RW) Internal factory assigned MAC address values
|
||||
+
|
||||
+What: /sys/bus/serial/devices/.../serial_number
|
||||
+Date: September 2020
|
||||
+Contact: Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
+Description: (RW) Internal factory assigned serial number
|
||||
+
|
||||
+What: /sys/bus/serial/devices/.../version
|
||||
+Date: September 2020
|
||||
+Contact: Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
+Description: (RO) Internal MCU firmware version
|
||||
+
|
||||
+What: /sys/bus/serial/devices/.../protocol_version
|
||||
+Date: September 2020
|
||||
+Contact: Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
+Description: (RO) Internal MCU communication protocol version
|
||||
+
|
||||
+What: /sys/bus/serial/devices/.../power_loss_recovery
|
||||
+Date: September 2020
|
||||
+Contact: Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
+Description: (RW) Host platform power loss recovery settings
|
||||
+ Value mapping: 0 - Always-On, 1 - Always-Off, 2 - Always-AC, 3 - Always-WA
|
||||
+
|
||||
+What: /sys/bus/serial/devices/.../bootloader_mode
|
||||
+Date: September 2020
|
||||
+Contact: Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
+Description: (RO) Internal MCU bootloader mode status
|
||||
+ Value mapping:
|
||||
+ 0 - normal mode
|
||||
+ 1 - bootloader mode
|
||||
+
|
||||
+What: /sys/bus/serial/devices/.../power_status
|
||||
+Date: September 2020
|
||||
+Contact: Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
+Description: (RO) Power status indicates the host platform power on method.
|
||||
+ Value mapping (bitwise list):
|
||||
+ 0x80 - Null
|
||||
+ 0x40 - Firmware flag
|
||||
+ 0x20 - Power loss detection flag (powered off)
|
||||
+ 0x10 - Power loss detection flag (AC mode)
|
||||
+ 0x08 - Button power on
|
||||
+ 0x04 - Wake-on-LAN power on
|
||||
+ 0x02 - RTC alarm power on
|
||||
+ 0x01 - AC recover power on
|
||||
+
|
||||
+What: /sys/bus/serial/devices/.../build_info
|
||||
+Date: September 2020
|
||||
+Contact: Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
+Description: (RO) Internal MCU firmware build date
|
||||
+ Format: yyyy/mm/dd hh:mm
|
||||
+
|
||||
+What: /sys/bus/serial/devices/.../ac_recovery_status
|
||||
+Date: September 2020
|
||||
+Contact: Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
+Description: (RO) Host platform AC recovery status value
|
||||
+ Value mapping:
|
||||
+ 0 - board has not been recovered from power down
|
||||
+ 1 - board has been recovered from power down
|
||||
@ -0,0 +1,74 @@
|
||||
From 0aff3e5923fecc6842473ad07a688d6e2f2c2d55 Mon Sep 17 00:00:00 2001
|
||||
From: Luka Kovacic <luka.kovacic () sartura ! hr>
|
||||
Date: Tue, 24 Aug 2021 12:44:37 +0000
|
||||
Subject: [PATCH 6/7] Documentation/hwmon: Add iei-wt61p803-puzzle hwmon driver
|
||||
documentation
|
||||
|
||||
Add the iei-wt61p803-puzzle driver hwmon driver interface documentation.
|
||||
|
||||
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
Signed-off-by: Pavo Banicevic <pavo.banicevic@sartura.hr>
|
||||
Cc: Luka Perkov <luka.perkov@sartura.hr>
|
||||
Cc: Robert Marko <robert.marko@sartura.hr>
|
||||
---
|
||||
.../hwmon/iei-wt61p803-puzzle-hwmon.rst | 43 +++++++++++++++++++
|
||||
Documentation/hwmon/index.rst | 1 +
|
||||
2 files changed, 44 insertions(+)
|
||||
create mode 100644 Documentation/hwmon/iei-wt61p803-puzzle-hwmon.rst
|
||||
|
||||
--- /dev/null
|
||||
+++ b/Documentation/hwmon/iei-wt61p803-puzzle-hwmon.rst
|
||||
@@ -0,0 +1,43 @@
|
||||
+.. SPDX-License-Identifier: GPL-2.0-only
|
||||
+
|
||||
+Kernel driver iei-wt61p803-puzzle-hwmon
|
||||
+=======================================
|
||||
+
|
||||
+Supported chips:
|
||||
+ * IEI WT61P803 PUZZLE for IEI Puzzle M801
|
||||
+
|
||||
+ Prefix: 'iei-wt61p803-puzzle-hwmon'
|
||||
+
|
||||
+Author: Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
+
|
||||
+
|
||||
+Description
|
||||
+-----------
|
||||
+
|
||||
+This driver adds fan and temperature sensor reading for some IEI Puzzle
|
||||
+series boards.
|
||||
+
|
||||
+Sysfs attributes
|
||||
+----------------
|
||||
+
|
||||
+The following attributes are supported:
|
||||
+
|
||||
+- IEI WT61P803 PUZZLE for IEI Puzzle M801
|
||||
+
|
||||
+/sys files in hwmon subsystem
|
||||
+-----------------------------
|
||||
+
|
||||
+================= == =====================================================
|
||||
+fan[1-5]_input RO files for fan speed (in RPM)
|
||||
+pwm[1-2] RW files for fan[1-2] target duty cycle (0..255)
|
||||
+temp[1-2]_input RO files for temperature sensors, in millidegree Celsius
|
||||
+================= == =====================================================
|
||||
+
|
||||
+/sys files in thermal subsystem
|
||||
+-------------------------------
|
||||
+
|
||||
+================= == =====================================================
|
||||
+cur_state RW file for current cooling state of the cooling device
|
||||
+ (0..max_state)
|
||||
+max_state RO file for maximum cooling state of the cooling device
|
||||
+================= == =====================================================
|
||||
--- a/Documentation/hwmon/index.rst
|
||||
+++ b/Documentation/hwmon/index.rst
|
||||
@@ -71,6 +71,7 @@ Hardware Monitoring Kernel Drivers
|
||||
ibmaem
|
||||
ibm-cffps
|
||||
ibmpowernv
|
||||
+ iei-wt61p803-puzzle-hwmon
|
||||
ina209
|
||||
ina2xx
|
||||
ina3221
|
||||
@ -0,0 +1,41 @@
|
||||
From 12479baad28d2a08c6cb9e83471057635fa1635c Mon Sep 17 00:00:00 2001
|
||||
From: Luka Kovacic <luka.kovacic () sartura ! hr>
|
||||
Date: Tue, 24 Aug 2021 12:44:38 +0000
|
||||
Subject: [PATCH 7/7] MAINTAINERS: Add an entry for the IEI WT61P803 PUZZLE
|
||||
driver
|
||||
|
||||
Add an entry for the IEI WT61P803 PUZZLE driver (MFD, HWMON, LED drivers).
|
||||
|
||||
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
Signed-off-by: Pavo Banicevic <pavo.banicevic@sartura.hr>
|
||||
Cc: Luka Perkov <luka.perkov@sartura.hr>
|
||||
Cc: Robert Marko <robert.marko@sartura.hr>
|
||||
---
|
||||
MAINTAINERS | 16 ++++++++++++++++
|
||||
1 file changed, 16 insertions(+)
|
||||
|
||||
--- a/MAINTAINERS
|
||||
+++ b/MAINTAINERS
|
||||
@@ -8538,6 +8538,22 @@ F: include/net/nl802154.h
|
||||
F: net/ieee802154/
|
||||
F: net/mac802154/
|
||||
|
||||
+IEI WT61P803 M801 MFD DRIVER
|
||||
+M: Luka Kovacic <luka.kovacic@sartura.hr>
|
||||
+M: Luka Perkov <luka.perkov@sartura.hr>
|
||||
+M: Goran Medic <goran.medic@sartura.hr>
|
||||
+L: linux-kernel@vger.kernel.org
|
||||
+S: Maintained
|
||||
+F: Documentation/ABI/stable/sysfs-driver-iei-wt61p803-puzzle
|
||||
+F: Documentation/devicetree/bindings/hwmon/iei,wt61p803-puzzle-hwmon.yaml
|
||||
+F: Documentation/devicetree/bindings/leds/iei,wt61p803-puzzle-leds.yaml
|
||||
+F: Documentation/devicetree/bindings/mfd/iei,wt61p803-puzzle.yaml
|
||||
+F: Documentation/hwmon/iei-wt61p803-puzzle-hwmon.rst
|
||||
+F: drivers/hwmon/iei-wt61p803-puzzle-hwmon.c
|
||||
+F: drivers/leds/leds-iei-wt61p803-puzzle.c
|
||||
+F: drivers/mfd/iei-wt61p803-puzzle.c
|
||||
+F: include/linux/mfd/iei-wt61p803-puzzle.h
|
||||
+
|
||||
IFE PROTOCOL
|
||||
M: Yotam Gigi <yotam.gi@gmail.com>
|
||||
M: Jamal Hadi Salim <jhs@mojatatu.com>
|
||||
@ -0,0 +1,247 @@
|
||||
--- a/drivers/leds/leds-iei-wt61p803-puzzle.c
|
||||
+++ b/drivers/leds/leds-iei-wt61p803-puzzle.c
|
||||
@@ -9,10 +9,13 @@
|
||||
#include <linux/mfd/iei-wt61p803-puzzle.h>
|
||||
#include <linux/mod_devicetable.h>
|
||||
#include <linux/module.h>
|
||||
+#include <linux/of.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/property.h>
|
||||
#include <linux/slab.h>
|
||||
|
||||
+#define IEI_LEDS_MAX 4
|
||||
+
|
||||
enum iei_wt61p803_puzzle_led_state {
|
||||
IEI_LED_OFF = 0x30,
|
||||
IEI_LED_ON = 0x31,
|
||||
@@ -34,6 +37,9 @@ struct iei_wt61p803_puzzle_led {
|
||||
unsigned char response_buffer[IEI_WT61P803_PUZZLE_BUF_SIZE];
|
||||
struct mutex lock; /* mutex to protect led_power_state */
|
||||
int led_power_state;
|
||||
+ int id;
|
||||
+ bool blinking;
|
||||
+ bool active_low;
|
||||
};
|
||||
|
||||
static inline struct iei_wt61p803_puzzle_led *cdev_to_iei_wt61p803_puzzle_led
|
||||
@@ -51,10 +57,20 @@ static int iei_wt61p803_puzzle_led_brigh
|
||||
size_t reply_size;
|
||||
int ret;
|
||||
|
||||
+ mutex_lock(&priv->lock);
|
||||
+ if (priv->blinking) {
|
||||
+ if (brightness == LED_OFF)
|
||||
+ priv->blinking = false;
|
||||
+ else
|
||||
+ return 0;
|
||||
+ }
|
||||
+ mutex_unlock(&priv->lock);
|
||||
+
|
||||
led_power_cmd[0] = IEI_WT61P803_PUZZLE_CMD_HEADER_START;
|
||||
led_power_cmd[1] = IEI_WT61P803_PUZZLE_CMD_LED;
|
||||
- led_power_cmd[2] = IEI_WT61P803_PUZZLE_CMD_LED_POWER;
|
||||
- led_power_cmd[3] = brightness == LED_OFF ? IEI_LED_OFF : IEI_LED_ON;
|
||||
+ led_power_cmd[2] = IEI_WT61P803_PUZZLE_CMD_LED_SET(priv->id);
|
||||
+ led_power_cmd[3] = ((brightness == LED_OFF) ^ priv->active_low) ?
|
||||
+ IEI_LED_OFF : IEI_LED_ON;
|
||||
|
||||
ret = iei_wt61p803_puzzle_write_command(priv->mcu, led_power_cmd,
|
||||
sizeof(led_power_cmd),
|
||||
@@ -90,39 +106,164 @@ static enum led_brightness iei_wt61p803_
|
||||
return led_state;
|
||||
}
|
||||
|
||||
+static int iei_wt61p803_puzzle_led_set_blink(struct led_classdev *cdev,
|
||||
+ unsigned long *delay_on,
|
||||
+ unsigned long *delay_off)
|
||||
+{
|
||||
+ struct iei_wt61p803_puzzle_led *priv = cdev_to_iei_wt61p803_puzzle_led(cdev);
|
||||
+ unsigned char led_blink_cmd[5] = {};
|
||||
+ unsigned char resp_buf[IEI_WT61P803_PUZZLE_BUF_SIZE];
|
||||
+ size_t reply_size;
|
||||
+ int ret = 0;
|
||||
+
|
||||
+ /* set defaults */
|
||||
+ if (!*delay_on && !*delay_off) {
|
||||
+ *delay_on = 500;
|
||||
+ *delay_off = 500;
|
||||
+ }
|
||||
+
|
||||
+ /* minimum delay for soft-driven blinking is 50ms to keep load low */
|
||||
+ if (*delay_on < 50)
|
||||
+ *delay_on = 50;
|
||||
+
|
||||
+ if (*delay_off < 50)
|
||||
+ *delay_off = 50;
|
||||
+
|
||||
+ if (*delay_on != *delay_off)
|
||||
+ return -EINVAL;
|
||||
+
|
||||
+ /* aggressively offload blinking to hardware, if possible */
|
||||
+ if (*delay_on < 100) {
|
||||
+ return -EINVAL;
|
||||
+ } else if (*delay_on < 200) {
|
||||
+ *delay_on = 100;
|
||||
+ *delay_off = 100;
|
||||
+ } else if (*delay_on <= 500) {
|
||||
+ *delay_on = 500;
|
||||
+ *delay_off = 500;
|
||||
+ } else {
|
||||
+ return -EINVAL;
|
||||
+ }
|
||||
+
|
||||
+ led_blink_cmd[0] = IEI_WT61P803_PUZZLE_CMD_HEADER_START;
|
||||
+ led_blink_cmd[1] = IEI_WT61P803_PUZZLE_CMD_LED;
|
||||
+ led_blink_cmd[2] = IEI_WT61P803_PUZZLE_CMD_LED_SET(priv->id);
|
||||
+ led_blink_cmd[3] = (*delay_on == 100)?IEI_LED_BLINK_5HZ:IEI_LED_BLINK_1HZ;
|
||||
+
|
||||
+ ret = iei_wt61p803_puzzle_write_command(priv->mcu, led_blink_cmd,
|
||||
+ sizeof(led_blink_cmd),
|
||||
+ resp_buf,
|
||||
+ &reply_size);
|
||||
+
|
||||
+ if (ret)
|
||||
+ return ret;
|
||||
+
|
||||
+ if (reply_size != 3)
|
||||
+ return -EIO;
|
||||
+
|
||||
+ if (!(resp_buf[0] == IEI_WT61P803_PUZZLE_CMD_HEADER_START &&
|
||||
+ resp_buf[1] == IEI_WT61P803_PUZZLE_CMD_RESPONSE_OK &&
|
||||
+ resp_buf[2] == IEI_WT61P803_PUZZLE_CHECKSUM_RESPONSE_OK))
|
||||
+ return -EIO;
|
||||
+
|
||||
+ mutex_lock(&priv->lock);
|
||||
+ priv->blinking = true;
|
||||
+ mutex_unlock(&priv->lock);
|
||||
+
|
||||
+ return ret;
|
||||
+}
|
||||
+
|
||||
+static int iei_wt61p803_puzzle_led_set_dt_default(struct led_classdev *cdev,
|
||||
+ struct device_node *np)
|
||||
+{
|
||||
+ const char *state;
|
||||
+ int ret = 0;
|
||||
+
|
||||
+ state = of_get_property(np, "default-state", NULL);
|
||||
+ if (state) {
|
||||
+ if (!strcmp(state, "on")) {
|
||||
+ ret =
|
||||
+ iei_wt61p803_puzzle_led_brightness_set_blocking(
|
||||
+ cdev, cdev->max_brightness);
|
||||
+ } else {
|
||||
+ ret = iei_wt61p803_puzzle_led_brightness_set_blocking(
|
||||
+ cdev, LED_OFF);
|
||||
+ }
|
||||
+ }
|
||||
+
|
||||
+ return ret;
|
||||
+}
|
||||
+
|
||||
static int iei_wt61p803_puzzle_led_probe(struct platform_device *pdev)
|
||||
{
|
||||
struct device *dev = &pdev->dev;
|
||||
+ struct device_node *np = dev_of_node(dev);
|
||||
+ struct device_node *child;
|
||||
struct iei_wt61p803_puzzle *mcu = dev_get_drvdata(dev->parent);
|
||||
struct iei_wt61p803_puzzle_led *priv;
|
||||
- struct led_init_data init_data = {};
|
||||
- struct fwnode_handle *child;
|
||||
int ret;
|
||||
+ u32 reg;
|
||||
|
||||
- if (device_get_child_node_count(dev) != 1)
|
||||
+ if (device_get_child_node_count(dev) > IEI_LEDS_MAX)
|
||||
return -EINVAL;
|
||||
|
||||
- priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
|
||||
- if (!priv)
|
||||
- return -ENOMEM;
|
||||
-
|
||||
- priv->mcu = mcu;
|
||||
- priv->led_power_state = 1;
|
||||
- mutex_init(&priv->lock);
|
||||
- dev_set_drvdata(dev, priv);
|
||||
-
|
||||
- child = device_get_next_child_node(dev, NULL);
|
||||
- init_data.fwnode = child;
|
||||
-
|
||||
- priv->cdev.brightness_set_blocking = iei_wt61p803_puzzle_led_brightness_set_blocking;
|
||||
- priv->cdev.brightness_get = iei_wt61p803_puzzle_led_brightness_get;
|
||||
- priv->cdev.max_brightness = 1;
|
||||
+ for_each_available_child_of_node(np, child) {
|
||||
+ struct led_init_data init_data = {};
|
||||
|
||||
- ret = devm_led_classdev_register_ext(dev, &priv->cdev, &init_data);
|
||||
- if (ret)
|
||||
- dev_err(dev, "Could not register LED\n");
|
||||
+ ret = of_property_read_u32(child, "reg", ®);
|
||||
+ if (ret) {
|
||||
+ dev_err(dev, "Failed to read led 'reg' property\n");
|
||||
+ goto put_child_node;
|
||||
+ }
|
||||
+
|
||||
+ if (reg > IEI_LEDS_MAX) {
|
||||
+ dev_err(dev, "Invalid led reg %u\n", reg);
|
||||
+ ret = -EINVAL;
|
||||
+ goto put_child_node;
|
||||
+ }
|
||||
+
|
||||
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
|
||||
+ if (!priv) {
|
||||
+ ret = -ENOMEM;
|
||||
+ goto put_child_node;
|
||||
+ }
|
||||
+
|
||||
+ mutex_init(&priv->lock);
|
||||
+
|
||||
+ dev_set_drvdata(dev, priv);
|
||||
+
|
||||
+ if (of_property_read_bool(child, "active-low"))
|
||||
+ priv->active_low = true;
|
||||
+
|
||||
+ priv->mcu = mcu;
|
||||
+ priv->id = reg;
|
||||
+ priv->led_power_state = 1;
|
||||
+ priv->blinking = false;
|
||||
+ init_data.fwnode = of_fwnode_handle(child);
|
||||
+
|
||||
+ priv->cdev.brightness_set_blocking = iei_wt61p803_puzzle_led_brightness_set_blocking;
|
||||
+ priv->cdev.brightness_get = iei_wt61p803_puzzle_led_brightness_get;
|
||||
+ priv->cdev.blink_set = iei_wt61p803_puzzle_led_set_blink;
|
||||
+
|
||||
+ priv->cdev.max_brightness = 1;
|
||||
+
|
||||
+ ret = iei_wt61p803_puzzle_led_set_dt_default(&priv->cdev, child);
|
||||
+ if (ret) {
|
||||
+ dev_err(dev, "Could apply default from DT\n");
|
||||
+ goto put_child_node;
|
||||
+ }
|
||||
+
|
||||
+ ret = devm_led_classdev_register_ext(dev, &priv->cdev, &init_data);
|
||||
+ if (ret) {
|
||||
+ dev_err(dev, "Could not register LED\n");
|
||||
+ goto put_child_node;
|
||||
+ }
|
||||
+ }
|
||||
+
|
||||
+ return ret;
|
||||
|
||||
- fwnode_handle_put(child);
|
||||
+put_child_node:
|
||||
+ of_node_put(child);
|
||||
return ret;
|
||||
}
|
||||
|
||||
--- a/include/linux/mfd/iei-wt61p803-puzzle.h
|
||||
+++ b/include/linux/mfd/iei-wt61p803-puzzle.h
|
||||
@@ -36,7 +36,7 @@
|
||||
#define IEI_WT61P803_PUZZLE_CMD_FUNCTION_OTHER_POWER_LOSS 0x41 /* A */
|
||||
|
||||
#define IEI_WT61P803_PUZZLE_CMD_LED 0x52 /* R */
|
||||
-#define IEI_WT61P803_PUZZLE_CMD_LED_POWER 0x31 /* 1 */
|
||||
+#define IEI_WT61P803_PUZZLE_CMD_LED_SET(n) (0x30 | (n))
|
||||
|
||||
#define IEI_WT61P803_PUZZLE_CMD_TEMP 0x54 /* T */
|
||||
#define IEI_WT61P803_PUZZLE_CMD_TEMP_ALL 0x41 /* A */
|
||||
Loading…
Reference in New Issue
Block a user