From dc2d4d73939c3d86a8e9d968c5c3462f92771bc6 Mon Sep 17 00:00:00 2001 From: Chukun Pan Date: Sat, 29 Apr 2023 23:08:26 +0800 Subject: [PATCH] mediatek: filogic: add Qihoo 360T7 support Hardware specification: SoC: MediaTek MT7981B 2x A53 Flash: ESMT F50L1G41LB 128MB RAM: MT5CC128M16JR-EK 256MB Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset, WPS Power: DC 12V 1A Flash instructions: 1. Attach UART, boot the stock firmware until the message about failsafe mode appears. 2. Enter failsafe mode by pressing "f" and "Enter" 3. Type "mount_root", then run "fw_setenv bootmenu_delay 3" 4. Back up all mtd partitions before flashing. 5. Reboot, U-Boot now presents a menu. 6. Connect to your PC via the Gigabit port of the router, set a static ip on the ethernet interface of your PC. (ip 192.168.1.254, gateway 192.168.1.1) 7. Select "Upgrade ATF BL2", then use this file: openwrt-mediatek-filogic-qihoo_360t7-preloader.bin 8. Select "Upgrade ATF FIP", then use this file: openwrt-mediatek-filogic-qihoo_360t7-bl31-uboot.fip 9. Download the initramfs image, and type "reset", waiting for tftp recovery to complete. a. After openwrt boots up, perform sysupgrade. Note: 1. Since NMBM is disabled, we must back up all partitions. 2. Flash instructions is based on commit 28df7f7. Signed-off-by: Chukun Pan --- .../mediatek/dts/mt7981b-qihoo-360t7.dts | 229 ++++++++++++++++++ .../filogic/base-files/etc/board.d/02_network | 8 + .../etc/hotplug.d/ieee80211/11_fix_wifi_mac | 5 + .../base-files/lib/upgrade/platform.sh | 1 + target/linux/mediatek/image/filogic.mk | 24 ++ 5 files changed, 267 insertions(+) create mode 100644 target/linux/mediatek/dts/mt7981b-qihoo-360t7.dts diff --git a/target/linux/mediatek/dts/mt7981b-qihoo-360t7.dts b/target/linux/mediatek/dts/mt7981b-qihoo-360t7.dts new file mode 100644 index 00000000000..87076d255cf --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-qihoo-360t7.dts @@ -0,0 +1,229 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; +#include +#include + +#include "mt7981.dtsi" + +/ { + model = "Qihoo 360T7"; + compatible = "qihoo,360t7", "mediatek,mt7981"; + + aliases { + serial0 = &uart0; + led-boot = &led_status_red; + led-failsafe = &led_status_red; + led-running = &led_status_green; + led-upgrade = &led_status_green; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0 0x40000000 0 0x10000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "wps"; + linux,code = ; + gpios = <&pio 0 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_status_red: red { + label = "red:status"; + gpios = <&pio 3 GPIO_ACTIVE_LOW>; + }; + + led_status_green: green { + label = "green:status"; + gpios = <&pio 7 GPIO_ACTIVE_LOW>; + }; + }; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; +}; + +&mdio_bus { + switch: switch@0 { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_flash_pins>; + status = "okay"; + + spi_nand@0 { + compatible = "spi-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + + spi-max-frequency = <52000000>; + spi-tx-buswidth = <4>; + spi-rx-buswidth = <4>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "bl2"; + reg = <0x0000000 0x0100000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x0100000 0x0080000>; + }; + + factory: partition@180000 { + label = "Factory"; + reg = <0x0180000 0x0200000>; + read-only; + }; + + partition@380000 { + label = "fip"; + reg = <0x0380000 0x0200000>; + read-only; + }; + + partition@580000 { + label = "ubi"; + reg = <0x0580000 0x6c00000>; + }; + + partition@7180000 { + label = "config"; + reg = <0x7180000 0x0100000>; + read-only; + }; + + partition@7280000 { + label = "factory"; + reg = <0x7280000 0x0080000>; + read-only; + }; + + partition@7300000 { + label = "log"; + reg = <0x7300000 0x0700000>; + read-only; + }; + }; + }; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan3"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan1"; + }; + + port@3 { + reg = <3>; + label = "wan"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; +}; + +&pio { + spi0_flash_pins: spi0-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + + conf-pu { + pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP"; + drive-strength = <8>; + mediatek,pull-up-adv = <0>; /* bias-disable */ + }; + + conf-pd { + pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO"; + drive-strength = <8>; + mediatek,pull-up-adv = <0>; /* bias-disable */ + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi { + status = "okay"; + + mediatek,mtd-eeprom = <&factory 0x0>; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index 2fca00921b8..a327a46108a 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -29,6 +29,9 @@ mediatek_setup_interfaces() mediatek,mt7988a-dsa-10g-spim-snand) ucidef_set_interfaces_lan_wan "lan0 lan1 lan2 lan3" "eth1 eth2" ;; + qihoo,360t7) + ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" wan + ;; tplink,tl-xdr4288|\ tplink,tl-xdr6088) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5" eth1 @@ -63,6 +66,11 @@ mediatek_setup_macs() bananapi,bpi-r3) wan_mac=$(macaddr_add $(cat /sys/class/net/eth0/address) 1) ;; + qihoo,360t7) + lan_mac=$(mtd_get_mac_ascii factory lanMac) + wan_mac=$(macaddr_add "$lan_mac" 1) + label_mac=$wan_mac + ;; xiaomi,redmi-router-ax6000-stock|\ xiaomi,redmi-router-ax6000-ubootmod) wan_mac=$(mtd_get_mac_ascii Bdata ethaddr_wan) diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac index a56e5bc6893..a3db00f5e8f 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac @@ -32,6 +32,11 @@ case "$board" in [ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress [ "$PHYNBR" = "1" ] && macaddr_setbit_la $(macaddr_add $addr 1) > /sys${DEVPATH}/macaddress ;; + qihoo,360t7) + addr=$(mtd_get_mac_ascii factory lanMac) + [ "$PHYNBR" = "0" ] && macaddr_add $addr 2 > /sys${DEVPATH}/macaddress + [ "$PHYNBR" = "1" ] && macaddr_add $addr 3 > /sys${DEVPATH}/macaddress + ;; tplink,tl-xdr4288|\ tplink,tl-xdr6086|\ tplink,tl-xdr6088) diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh index 9a7a5aaffb0..5b624bc5517 100755 --- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh @@ -70,6 +70,7 @@ platform_do_upgrade() { cudy,wr3000-v1) default_do_upgrade "$1" ;; + qihoo,360t7|\ tplink,tl-xdr4288|\ tplink,tl-xdr6086|\ tplink,tl-xdr6088|\ diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index da0d81c3461..d1a0a441386 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -233,6 +233,30 @@ define Device/mediatek_mt7988a-rfb-nand endef TARGET_DEVICES += mediatek_mt7988a-rfb-nand +define Device/qihoo_360t7 + DEVICE_VENDOR := Qihoo + DEVICE_MODEL := 360T7 + DEVICE_DTS := mt7981b-qihoo-360t7 + DEVICE_DTS_DIR := ../dts + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + KERNEL_IN_UBI := 1 + UBOOTENV_IN_UBI := 1 + IMAGES := sysupgrade.itb + KERNEL_INITRAMFS_SUFFIX := -recovery.itb + KERNEL := kernel-bin | gzip + KERNEL_INITRAMFS := kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k + IMAGE/sysupgrade.itb := append-kernel | \ + fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata + DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware + ARTIFACTS := preloader.bin bl31-uboot.fip + ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3 + ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot qihoo_360t7 +endef +TARGET_DEVICES += qihoo_360t7 + define Device/tplink_tl-xdr-common DEVICE_VENDOR := TP-Link DEVICE_DTS_DIR := ../dts