mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-23 15:32:33 +00:00
ar71xx: add support for ALFA Network R36A
ALFA Network R36A is a successor of the previous model, the R36 (Ralink RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2. Specification: - 650/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 2T2R (QCA9531) 2.4 GHz, 2x u.fl connectors on PCB - 1x USB 2.0 (power controlled by GPIO) - 6x LED (5 of them are driven by GPIO) - 2x button (reset, wifi/wps) - external h/w watchdog (EM6324QYSP5B, disabled and not used) - DC jack for main power input (12 V) - UART header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmware which is based on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This commit is contained in:
Piotr Dymacz
parent
1f06144cde
commit
af8f0629df
@ -580,6 +580,12 @@ pqi-air-pen)
|
||||
qihoo-c301)
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2G" "qihoo:red:status" "phy1tpt"
|
||||
;;
|
||||
r36a)
|
||||
ucidef_set_led_netdev "lan" "LAN" "$board:blue:lan" "eth0"
|
||||
ucidef_set_led_usbdev "usb" "USB" "$board:blue:usb" "1-1"
|
||||
ucidef_set_led_netdev "wan" "WAN" "$board:blue:wan" "eth1"
|
||||
ucidef_set_led_wlan "wlan" "WLAN" "$board:blue:wlan" "phy0tpt"
|
||||
;;
|
||||
r602n|\
|
||||
zbt-we1526)
|
||||
ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth1"
|
||||
|
||||
@ -181,7 +181,8 @@ get_status_led() {
|
||||
oolite)
|
||||
status_led="$board:red:system"
|
||||
;;
|
||||
dw33d)
|
||||
dw33d|\
|
||||
r36a)
|
||||
status_led="$board:blue:status"
|
||||
;;
|
||||
eap300v2)
|
||||
|
||||
@ -847,6 +847,9 @@ ar71xx_board_detect() {
|
||||
*"Qihoo 360 C301")
|
||||
name="qihoo-c301"
|
||||
;;
|
||||
*"R36A")
|
||||
name="r36a"
|
||||
;;
|
||||
*"R602N")
|
||||
name="r602n"
|
||||
;;
|
||||
|
||||
@ -257,6 +257,7 @@ platform_check_image() {
|
||||
nanostation-m-xw|\
|
||||
nbg460n_550n_550nh|\
|
||||
pqi-air-pen|\
|
||||
r36a|\
|
||||
r602n|\
|
||||
rocket-m|\
|
||||
rocket-m-ti|\
|
||||
|
||||
@ -153,6 +153,7 @@ CONFIG_ATH79=y
|
||||
# CONFIG_ATH79_MACH_PB44 is not set
|
||||
# CONFIG_ATH79_MACH_PQI_AIR_PEN is not set
|
||||
# CONFIG_ATH79_MACH_QIHOO_C301 is not set
|
||||
# CONFIG_ATH79_MACH_R36A is not set
|
||||
# CONFIG_ATH79_MACH_R602N is not set
|
||||
# CONFIG_ATH79_MACH_R6100 is not set
|
||||
# CONFIG_ATH79_MACH_RAMBUTAN is not set
|
||||
|
||||
@ -151,6 +151,7 @@ CONFIG_ATH79=y
|
||||
# CONFIG_ATH79_MACH_PB44 is not set
|
||||
# CONFIG_ATH79_MACH_PQI_AIR_PEN is not set
|
||||
# CONFIG_ATH79_MACH_QIHOO_C301 is not set
|
||||
# CONFIG_ATH79_MACH_R36A is not set
|
||||
# CONFIG_ATH79_MACH_R602N is not set
|
||||
# CONFIG_ATH79_MACH_R6100 is not set
|
||||
# CONFIG_ATH79_MACH_RAMBUTAN is not set
|
||||
|
||||
@ -934,6 +934,16 @@ config ATH79_MACH_WRTNODE2Q
|
||||
select ATH79_DEV_M25P80
|
||||
select ATH79_DEV_WMAC
|
||||
|
||||
config ATH79_MACH_R36A
|
||||
bool "ALFA Network R36A support"
|
||||
select SOC_QCA953X
|
||||
select ATH79_DEV_ETH
|
||||
select ATH79_DEV_GPIO_BUTTONS
|
||||
select ATH79_DEV_LEDS_GPIO
|
||||
select ATH79_DEV_M25P80
|
||||
select ATH79_DEV_USB
|
||||
select ATH79_DEV_WMAC
|
||||
|
||||
config ATH79_MACH_R602N
|
||||
bool "P&W R602N support"
|
||||
select SOC_QCA953X
|
||||
|
||||
@ -162,6 +162,7 @@ obj-$(CONFIG_ATH79_MACH_PB42) += mach-pb42.o
|
||||
obj-$(CONFIG_ATH79_MACH_PB44) += mach-pb44.o
|
||||
obj-$(CONFIG_ATH79_MACH_PQI_AIR_PEN) += mach-pqi-air-pen.o
|
||||
obj-$(CONFIG_ATH79_MACH_QIHOO_C301) += mach-qihoo-c301.o
|
||||
obj-$(CONFIG_ATH79_MACH_R36A) += mach-r36a.o
|
||||
obj-$(CONFIG_ATH79_MACH_R602N) += mach-r602n.o
|
||||
obj-$(CONFIG_ATH79_MACH_R6100) += mach-r6100.o
|
||||
obj-$(CONFIG_ATH79_MACH_RB2011) += mach-rb2011.o
|
||||
|
||||
140
target/linux/ar71xx/files/arch/mips/ath79/mach-r36a.c
Normal file
140
target/linux/ar71xx/files/arch/mips/ath79/mach-r36a.c
Normal file
@ -0,0 +1,140 @@
|
||||
/*
|
||||
* ALFA Network R36A board support
|
||||
*
|
||||
* Copyright (C) 2018 Piotr Dymacz <pepe2k@gmail.com>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify it
|
||||
* under the terms of the GNU General Public License version 2 as published
|
||||
* by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
#include <linux/gpio.h>
|
||||
#include <linux/platform_device.h>
|
||||
|
||||
#include <asm/mach-ath79/ath79.h>
|
||||
#include <asm/mach-ath79/ar71xx_regs.h>
|
||||
|
||||
#include "common.h"
|
||||
#include "dev-eth.h"
|
||||
#include "dev-gpio-buttons.h"
|
||||
#include "dev-leds-gpio.h"
|
||||
#include "dev-m25p80.h"
|
||||
#include "dev-usb.h"
|
||||
#include "dev-wmac.h"
|
||||
#include "machtypes.h"
|
||||
|
||||
#define R36A_GPIO_LED_LAN 4
|
||||
#define R36A_GPIO_LED_STATUS 14
|
||||
#define R36A_GPIO_LED_USB 12
|
||||
#define R36A_GPIO_LED_WAN 16
|
||||
#define R36A_GPIO_LED_WLAN 15
|
||||
|
||||
#define R36A_GPIO_WDT_EN 1
|
||||
#define R36A_GPIO_WDT_IN 0
|
||||
#define R36A_GPIO_USB_PWR 3
|
||||
|
||||
#define R36A_GPIO_BTN_RESET 2
|
||||
#define R36A_GPIO_BTN_RFKILL 17
|
||||
|
||||
#define R36A_KEYS_POLL_INTERVAL 20
|
||||
#define R36A_KEYS_DEBOUNCE_INTERVAL (3 * R36A_KEYS_POLL_INTERVAL)
|
||||
|
||||
#define R36A_WMAC_CALDATA_OFFSET 0x1000
|
||||
|
||||
static struct gpio_led r36a_leds_gpio[] __initdata = {
|
||||
{
|
||||
.name = "r36a:blue:lan",
|
||||
.gpio = R36A_GPIO_LED_LAN,
|
||||
.active_low = 1,
|
||||
}, {
|
||||
.name = "r36a:blue:status",
|
||||
.gpio = R36A_GPIO_LED_STATUS,
|
||||
.active_low = 1,
|
||||
}, {
|
||||
.name = "r36a:blue:usb",
|
||||
.gpio = R36A_GPIO_LED_USB,
|
||||
.active_low = 1,
|
||||
}, {
|
||||
.name = "r36a:blue:wan",
|
||||
.gpio = R36A_GPIO_LED_WAN,
|
||||
.active_low = 1,
|
||||
}, {
|
||||
.name = "r36a:blue:wlan",
|
||||
.gpio = R36A_GPIO_LED_WLAN,
|
||||
.active_low = 1,
|
||||
},
|
||||
};
|
||||
|
||||
static struct gpio_keys_button r36a_gpio_keys[] __initdata = {
|
||||
{
|
||||
.desc = "reset",
|
||||
.type = EV_KEY,
|
||||
.code = KEY_RESTART,
|
||||
.debounce_interval = R36A_KEYS_DEBOUNCE_INTERVAL,
|
||||
.gpio = R36A_GPIO_BTN_RESET,
|
||||
.active_low = 1,
|
||||
}, {
|
||||
.desc = "rfkill",
|
||||
.type = EV_KEY,
|
||||
.code = KEY_RFKILL,
|
||||
.debounce_interval = R36A_KEYS_DEBOUNCE_INTERVAL,
|
||||
.gpio = R36A_GPIO_BTN_RFKILL,
|
||||
.active_low = 1,
|
||||
},
|
||||
};
|
||||
|
||||
static void __init r36a_setup(void)
|
||||
{
|
||||
u8 *art = (u8 *) KSEG1ADDR(0x1f070000);
|
||||
|
||||
ath79_register_m25p80(NULL);
|
||||
|
||||
ath79_setup_ar933x_phy4_switch(false, false);
|
||||
|
||||
ath79_register_mdio(0, 0x0);
|
||||
|
||||
ath79_switch_data.phy4_mii_en = 1;
|
||||
ath79_switch_data.phy_poll_mask = 0xf7;
|
||||
|
||||
/* LAN */
|
||||
ath79_eth0_data.duplex = DUPLEX_FULL;
|
||||
ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
|
||||
ath79_eth0_data.phy_mask = BIT(4);
|
||||
ath79_eth0_data.speed = SPEED_100;
|
||||
ath79_init_mac(ath79_eth0_data.mac_addr, art, 0);
|
||||
ath79_register_eth(0);
|
||||
|
||||
/* WAN */
|
||||
ath79_eth1_data.duplex = DUPLEX_FULL;
|
||||
ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
|
||||
ath79_init_mac(ath79_eth1_data.mac_addr, art, 1);
|
||||
ath79_register_eth(1);
|
||||
|
||||
/* Disable JTAG (enables GPIO0-3) */
|
||||
ath79_gpio_function_enable(AR934X_GPIO_FUNC_JTAG_DISABLE);
|
||||
|
||||
ath79_register_leds_gpio(-1, ARRAY_SIZE(r36a_leds_gpio),
|
||||
r36a_leds_gpio);
|
||||
|
||||
ath79_register_gpio_keys_polled(-1, R36A_KEYS_POLL_INTERVAL,
|
||||
ARRAY_SIZE(r36a_gpio_keys),
|
||||
r36a_gpio_keys);
|
||||
|
||||
gpio_request_one(R36A_GPIO_WDT_IN,
|
||||
GPIOF_OUT_INIT_LOW | GPIOF_EXPORT_DIR_FIXED,
|
||||
"WDT input");
|
||||
|
||||
gpio_request_one(R36A_GPIO_WDT_EN,
|
||||
GPIOF_OUT_INIT_LOW | GPIOF_EXPORT_DIR_FIXED,
|
||||
"WDT enable");
|
||||
|
||||
gpio_request_one(R36A_GPIO_USB_PWR,
|
||||
GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED,
|
||||
"USB power");
|
||||
|
||||
ath79_register_wmac(art + R36A_WMAC_CALDATA_OFFSET, NULL);
|
||||
|
||||
ath79_register_usb();
|
||||
}
|
||||
|
||||
MIPS_MACHINE(ATH79_MACH_R36A, "R36A", "ALFA Network R36A", r36a_setup);
|
||||
@ -166,6 +166,7 @@ enum ath79_mach_type {
|
||||
ATH79_MACH_PB44, /* Atheros PB44 reference board */
|
||||
ATH79_MACH_PQI_AIR_PEN, /* PQI Air Pen */
|
||||
ATH79_MACH_QIHOO_C301, /* Qihoo 360 C301 */
|
||||
ATH79_MACH_R36A, /* ALFA Network R36A */
|
||||
ATH79_MACH_R602N, /* P&W R602N */
|
||||
ATH79_MACH_R6100, /* NETGEAR R6100 */
|
||||
ATH79_MACH_RAMBUTAN, /* 8devices Rambutan */
|
||||
|
||||
@ -120,6 +120,7 @@ CONFIG_ATH79_MACH_PB42=y
|
||||
CONFIG_ATH79_MACH_PB44=y
|
||||
CONFIG_ATH79_MACH_PQI_AIR_PEN=y
|
||||
CONFIG_ATH79_MACH_QIHOO_C301=y
|
||||
CONFIG_ATH79_MACH_R36A=y
|
||||
CONFIG_ATH79_MACH_R602N=y
|
||||
CONFIG_ATH79_MACH_RE450=y
|
||||
CONFIG_ATH79_MACH_RUT9XX=y
|
||||
|
||||
@ -631,6 +631,18 @@ define Device/jwap230
|
||||
endef
|
||||
TARGET_DEVICES += jwap230
|
||||
|
||||
define Device/r36a
|
||||
DEVICE_TITLE := ALFA Network R36A
|
||||
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport -swconfig
|
||||
BOARDNAME := R36A
|
||||
SUPPORTED_DEVICES := r36a
|
||||
IMAGE_SIZE := 15872k
|
||||
MTDPARTS := spi0.0:384k(u-boot)ro,64k(u-boot-env),64k(art)ro,-(firmware)
|
||||
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
||||
append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
|
||||
endef
|
||||
TARGET_DEVICES += r36a
|
||||
|
||||
define Device/r602n
|
||||
DEVICE_TITLE := P&W R602N
|
||||
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
|
||||
|
||||
Loading…
Reference in New Issue
Block a user