ramips: use destinct 11AC NAS board name

Use a distinct board name even if the board is near to identical to
the WeVO W2914NS v2.

To make sure that a 11AC NAS image can not be installed on a
WeVO W2914NS v2, both board need to use different names.

Signed-off-by: Mathias Kresin <dev@kresin.me>

target/linux/ramips/base-files/etc/board.d/01_leds

@@ -17,6 +17,16 @@ board=$(ramips_board_name)
 board_config_update
 
 case $board in
+11acnas|\
+all0239-3g|\
+hw550-3g|\
+mofi3500-3gn|\
+sap-g3200u3|\
+sk-wb8|\
+w2914nsv2|\
+wf-2881)
+	set_usb_led "$board:green:usb"
+	;;
 3g150b|\
 3g300m)
 	set_usb_led "$board:blue:3g"
@@ -45,14 +55,6 @@ air3gii)
 	set_wifi_led "$board:green:wlan"
 	set_usb_led "$board:green:mobile"
 	;;
-all0239-3g|\
-hw550-3g|\
-mofi3500-3gn|\
-sap-g3200u3|\
-sk-wb8|\
-wf-2881)
-	set_usb_led "$board:green:usb"
-	;;
 all0256n)
 	ucidef_set_rssimon "wlan0" "200000" "1"
 	ucidef_set_led_rssi "rssilow" "RSSILOW" "$board:green:rssilow" "wlan0" "1" "40" "0" "6"
@@ -315,9 +317,6 @@ vocore)
 	ucidef_set_led_netdev "eth" "ETH" "$board:orange:eth" "eth0"
 	set_wifi_led "$board:green:status"
 	;;
-w2914nsv2)
-	set_usb_led "$board:green:usb"
-	;;
 w502u)
 	set_usb_led "$board:blue:usb"
 	set_wifi_led "rt2800pci-phy0::radio"

target/linux/ramips/base-files/etc/board.d/02_network

@@ -32,6 +32,11 @@ ramips_setup_interfaces()
 	local board="$1"
 
 	case $board in
+	11acnas|\
+	w2914nsv2)
+		ucidef_add_switch "switch0" \
+			"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "4:wan:5" "6@eth0"
+		;;
 	3g150b|\
 	3g300m|\
 	a5-v11|\
@@ -251,10 +256,6 @@ ramips_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0"
 		;;
-	w2914nsv2)
-		ucidef_add_switch "switch0" \
-			"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "4:wan:5" "6@eth0"
-		;;
 	wcr-150gn)
 		ucidef_add_switch "switch0" \
 			"0:lan" "6t@eth0"

target/linux/ramips/base-files/lib/ramips.sh

@@ -14,7 +14,7 @@ ramips_board_detect() {
 
 	case "$machine" in
 	*"11AC NAS Router")
-		name="w2914nsv2"
+		name="11acnas"
 		;;
 	*"3G150B")
 		name="3g150b"

target/linux/ramips/dts/11ACNAS.dts

@@ -9,4 +9,18 @@
 		device_type = "memory";
 		reg = <0x0 0x10000000>;
 	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		// Only USB LED is connected to GPIO.
+		// All of other LEDs are connected directly to
+		// switch, WiFi chip, Vcc, so they are not controllable
+		// via GPIO
+
+		usb {
+			label = "11acnas:green:usb";
+			gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
+		};
+	};
 };

target/linux/ramips/dts/W2914NSV2.dts

@@ -9,4 +9,18 @@
 		device_type = "memory";
 		reg = <0x0 0x8000000>;
 	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		// Only USB LED is connected to GPIO.
+		// All of other LEDs are connected directly to
+		// switch, WiFi chip, Vcc, so they are not controllable
+		// via GPIO
+
+		usb {
+			label = "w2914nsv2:green:usb";
+			gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
+		};
+	};
 };

target/linux/ramips/dts/W2914NSV2.dtsi

@@ -26,20 +26,6 @@
 			linux,code = <KEY_WPS_BUTTON>;
 		};
 	};
-
-	gpio-leds {
-		compatible = "gpio-leds";
-
-		// Only USB LED is connected to GPIO.
-		// All of other LEDs are connected directly to
-		// switch, WiFi chip, Vcc, so they are not controllable
-		// via GPIO
-
-		usb {
-			label = "w2914nsv2:green:usb";
-			gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
-		};
-	};
 };
 
 &xhci {