ath79: add support for Senao Engenius ESR1750

FCC ID: A8J-ESR1750

Engenius ESR1750 is an indoor wireless router with
a gigabit ethernet switch, dual-band wireless,
internal antenna plates, and a USB 2.0 port

**Specification:**

  - QCA9558 SOC		2.4 GHz, 3x3
  - QCA9880 WLAN	PCIe mini card, 5 GHz, 3x3
  - QCA8337N SW		4 ports LAN, 1 port WAN
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 2x 64 MB RAM
  - UART at J1		populated, RX grounded
  - 6 internal antenna plates (omni-directional)
  - 5 LEDs, 1 button (power, 2G, 5G, WAN, WPS) (reset)

**MAC addresses:**

  Base MAC address labeled as "MAC ADDRESS"
  MAC "wanaddr" is similar to "ethaddr"

  eth0 *:58 MAC u-boot-env ethaddr
  phy0 *:58 MAC u-boot-env ethaddr
  phy1 *:59 --- u-boot-env ethaddr +1
  WAN  *:10:58  u-boot-env wanaddr

**Serial Access:**

  RX on the board for UART is shorted to ground by resistor R176
  therefore it must be removed to use the console
  but it is not necessary to remove to view boot log

  optionally, R175 can be replaced with a solder bridge short

  the resistors R175 and R176 are next to the UART RX pin

**Installation:**

  Method 1: Firmware upgrade page

    NOTE: ESR1750 might require the factory.bin
      for ESR1200 instead, OEM provides 1 image for both.

    OEM webpage at 192.168.0.1
    username and password "admin"
    Navigate to Settings (gear icon) --> Tools --> Firmware
    select the factory.bin image
    confirm and wait 3 minutes

  Method 2: TFTP recovery

    Follow TFTP instructions using initramfs.bin
    use sysupgrade.bin to flash using openwrt web interface

**Return to OEM:**

  MTD partitions should be backed up before flashing
  using TFTP to boot openwrt without overwriting flash

  Alternatively, it is possible to edit OEM firmware images
  to flash MTD partitions in openwrt to restore OEM firmware
  by removing the OEM header and writing the rest to "firmware"

**TFTP recovery:**

  Requires serial console, reset button does nothing at boot

  rename initramfs.bin to 'uImageESR1200'
  make available on TFTP server at 192.168.99.8
  power board, interrupt boot by pressing '4' rapidly
  execute tftpboot and bootm

**Note on ETH switch registers**

  Registers must be written to the ethernet switch
  in order to set up the switch's MAC interface.
  U-boot can write the registers on it's own
  which is needed, for example, in a TFTP transfer.

  The register bits from OEM for the QCA8337 switch
  can be read from interrupted boot (tftpboot, bootm)
  by adding print lines in the switch driver ar8327.c
  before 'qca,ar8327-initvals' is parsed from DTS and written.
  for example:

    pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));

Signed-off-by: Michael Pratt <mcpratt@pm.me>
This commit is contained in:
Michael Pratt 2023-01-22 03:21:53 -05:00 committed by Hauke Mehrtens
parent 2f99f7e2d0
commit 96c2119dba
5 changed files with 97 additions and 0 deletions

View File

@ -0,0 +1,79 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "qca955x_senao_router-dual.dtsi"
/ {
compatible = "engenius,esr1750", "qca,qca9558";
model = "EnGenius ESR1750";
aliases {
led-boot = &led_power;
led-failsafe = &led_power;
led-running = &led_power;
led-upgrade = &led_power;
};
leds {
compatible = "gpio-leds";
led_power: power {
label = "amber:power";
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
default-state = "on";
};
wlan2g {
label = "blue:wlan2g";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy1tpt";
};
wlan5g {
label = "blue:wlan5g";
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
wps_amber {
label = "amber:wps";
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
};
wps_blue {
label = "blue:wps";
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
};
};
};
&phy0 {
qca,mib-poll-interval = <500>;
qca,ar8327-initvals = <
0x04 0x87680000 /* PORT0 PAD MODE CTRL */
0x10 0x40000000 /* POWER_ON_STRAP */
0x50 0xcf35cf35 /* LED_CTRL0 */
0x54 0xcf35cf35 /* LED_CTRL1 */
0x58 0xcf35cf35 /* LED_CTRL2 */
0x5c 0x03ffff00 /* LED_CTRL3 */
0x7c 0x0000007e /* PORT0_STATUS */
>;
};
&usb_phy1 {
status = "okay";
};
&usb1 {
status = "okay";
};
&wmac {
nvmem-cells = <&calibration_art_1000>;
nvmem-cell-names = "calibration";
};
&ath10k_0 {
nvmem-cells = <&calibration_art_5000>;
nvmem-cell-names = "calibration";
};

View File

@ -287,6 +287,7 @@ ath79_setup_interfaces()
dlink,dir-842-c3|\ dlink,dir-842-c3|\
dlink,dir-859-a1|\ dlink,dir-859-a1|\
engenius,epg5000|\ engenius,epg5000|\
engenius,esr1750|\
engenius,esr900|\ engenius,esr900|\
sitecom,wlr-7100|\ sitecom,wlr-7100|\
tplink,archer-c2-v3|\ tplink,archer-c2-v3|\
@ -667,6 +668,7 @@ ath79_setup_macs()
label_mac=$lan_mac label_mac=$lan_mac
;; ;;
engenius,epg5000|\ engenius,epg5000|\
engenius,esr1750|\
engenius,esr900) engenius,esr900)
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr) lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr) wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)

View File

@ -35,6 +35,7 @@ case "$board" in
[ "$PHYNBR" -eq 1 ] && \ [ "$PHYNBR" -eq 1 ] && \
mtd_get_mac_ascii bdcfg "wlanmac" > /sys${DEVPATH}/macaddress mtd_get_mac_ascii bdcfg "wlanmac" > /sys${DEVPATH}/macaddress
;; ;;
engenius,esr1750|\
engenius,esr900) engenius,esr900)
macaddr_add "$(mtd_get_mac_ascii u-boot-env ethaddr)" "$PHYNBR" > /sys${DEVPATH}/macaddress macaddr_add "$(mtd_get_mac_ascii u-boot-env ethaddr)" "$PHYNBR" > /sys${DEVPATH}/macaddress
;; ;;

View File

@ -12,6 +12,7 @@ preinit_set_mac_address() {
ip link set dev eth0 address $(mtd_get_mac_ascii bdcfg "lanmac") ip link set dev eth0 address $(mtd_get_mac_ascii bdcfg "lanmac")
ip link set dev eth1 address $(mtd_get_mac_ascii bdcfg "wanmac") ip link set dev eth1 address $(mtd_get_mac_ascii bdcfg "wanmac")
;; ;;
engenius,esr1750|\
engenius,esr900) engenius,esr900)
ip link set dev eth0 address $(mtd_get_mac_ascii u-boot-env ethaddr) ip link set dev eth0 address $(mtd_get_mac_ascii u-boot-env ethaddr)
;; ;;

View File

@ -1299,6 +1299,20 @@ define Device/engenius_epg5000
endef endef
TARGET_DEVICES += engenius_epg5000 TARGET_DEVICES += engenius_epg5000
define Device/engenius_esr1750
SOC := qca9558
DEVICE_VENDOR := EnGenius
DEVICE_MODEL := ESR1750
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2
IMAGE_SIZE := 14656k
IMAGES += factory.dlf
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | \
senao-header -r 0x101 -p 0x62 -t 2
SUPPORTED_DEVICES += esr1750 esr1200 engenius,esr1200
endef
TARGET_DEVICES += engenius_esr1750
define Device/engenius_esr900 define Device/engenius_esr900
SOC := qca9558 SOC := qca9558
DEVICE_VENDOR := EnGenius DEVICE_VENDOR := EnGenius