mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-19 21:58:04 +00:00
Add support for Netgear EX6200V2
Specifications: SOC: Qualcomm ARM Quad-Core ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d RAM: 256 MB Winbond W632GU6KB-12 FLASH: 16 MiB Winbond W25Q128 ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac 2x2 INPUT: Power, WPS, reset button LED: 5Ghz Radio, 2.4Ghz Radio, Client, USB SERIAL: Header accessible through rectangular cutout in plastic shield. VCC, TX, RX, GND The Serial setting is 115200-8-N-1. Tested and working: Ethernet 2.4 GHz WiFi (Correct MAC-address) 5 GHz WiFi (Correct MAC-address) Factory installation from WebIF OpenWRT sysupgrade LEDs USB Port Not Tested: WPS Button Install via Web-Interface: Upload the factory image to the device to the Netgear Web-Interface. The device might asks you to confirm the update a second time due to detecting the OpenWRT firmware as older. The device will automatically reboot after the image is written to flash. Signed-off-by: Isaac Velez <velezis@outlook.com>
This commit is contained in:
Isaac Velez
parent
8f7be2a2ba
commit
85bfc77517
@ -101,6 +101,10 @@ netgear,ex6150v2)
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2G" "green:router" "phy0tpt"
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN5G" "green:client" "phy1tpt"
|
||||
;;
|
||||
netgear,ex6200v2)
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN2G" "green:wlan2g" "phy0radio"
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN5G" "green:wlan5g" "phy1radio"
|
||||
;;
|
||||
qxwlan,e2600ac-c1 |\
|
||||
qxwlan,e2600ac-c2)
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN0" "green:wlan0" "phy0tpt"
|
||||
|
||||
@ -90,6 +90,9 @@ ipq40xx_setup_interfaces()
|
||||
netgear,srs60)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan"
|
||||
;;
|
||||
netgear,ex6200v2)
|
||||
ucidef_set_interface_lan "lan1 lan2 lan3 lan4 lan5"
|
||||
;;
|
||||
openmesh,a42|\
|
||||
openmesh,a62)
|
||||
ucidef_set_interfaces_lan_wan "ethernet2" "ethernet1"
|
||||
|
||||
@ -0,0 +1,44 @@
|
||||
/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
|
||||
* Copyright (c) 2018, David Bauer <mail@david-bauer.net>
|
||||
*
|
||||
* Permission to use, copy, modify, and/or distribute this software for any
|
||||
* purpose with or without fee is hereby granted, provided that the above
|
||||
* copyright notice and this permission notice appear in all copies.
|
||||
*
|
||||
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
|
||||
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
|
||||
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
|
||||
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
|
||||
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
|
||||
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
|
||||
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
|
||||
*
|
||||
*/
|
||||
|
||||
#include "qcom-ipq4018-ex62x0v2.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Netgear EX6200v2";
|
||||
compatible = "netgear,ex6200v2";
|
||||
|
||||
};
|
||||
|
||||
&usb2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb2_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_ss_phy {
|
||||
status = "okay";
|
||||
};
|
||||
@ -0,0 +1,414 @@
|
||||
/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
|
||||
* Copyright (c) 2018, David Bauer <mail@david-bauer.net>
|
||||
*
|
||||
* Permission to use, copy, modify, and/or distribute this software for any
|
||||
* purpose with or without fee is hereby granted, provided that the above
|
||||
* copyright notice and this permission notice appear in all copies.
|
||||
*
|
||||
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
|
||||
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
|
||||
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
|
||||
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
|
||||
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
|
||||
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
|
||||
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
|
||||
*
|
||||
*/
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "Netgear EX62x0v2";
|
||||
compatible = "netgear,ex62x0v2";
|
||||
|
||||
soc {
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &power_amber;
|
||||
led-failsafe = &power_amber;
|
||||
led-running = &power_green;
|
||||
led-upgrade = &power_amber;
|
||||
label-mac-device = &gmac;
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
led_spi {
|
||||
compatible = "spi-gpio";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
sck-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
|
||||
mosi-gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
|
||||
num-chipselects = <0>;
|
||||
|
||||
led_gpio: led_gpio@0 {
|
||||
compatible = "fairchild,74hc595";
|
||||
reg = <0>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
registers-number = <1>;
|
||||
spi-max-frequency = <1000000>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
power_amber: led-power-amber {
|
||||
label = "amber:power";
|
||||
gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
power_green: led-power-green {
|
||||
label = "green:power";
|
||||
gpios = <&led_gpio 5 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan2g_green {
|
||||
label = "green:wlan2g";
|
||||
gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>;
|
||||
|
||||
};
|
||||
|
||||
wlan2g_red {
|
||||
label = "red:wlan2g";
|
||||
gpios = <&led_gpio 4 GPIO_ACTIVE_LOW>;
|
||||
|
||||
};
|
||||
|
||||
wlan5g_green {
|
||||
label = "green:wlan5g";
|
||||
gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan5g_red {
|
||||
label = "red:wlan5g";
|
||||
gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
usb_green {
|
||||
label = "green:usb";
|
||||
gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>;
|
||||
trigger-sources = <&usb2_port1>, <&usb3_port1>;
|
||||
linux,default-trigger = "usbport";
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
serial_pins: serial_pinmux {
|
||||
mux {
|
||||
pins = "gpio60", "gpio61";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_0_pins: spi_0_pinmux {
|
||||
pin {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio55", "gpio56", "gpio57";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
pin_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio54";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
|
||||
enable-usb-power {
|
||||
gpio-hog;
|
||||
gpios = <3 GPIO_ACTIVE_HIGH>;
|
||||
output-high;
|
||||
line-name = "enable USB power";
|
||||
};
|
||||
};
|
||||
&blsp1_spi1 {
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <45000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition0@0 {
|
||||
label = "SBL1";
|
||||
reg = <0x00000000 0x00040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition1@40000 {
|
||||
label = "MIBIB";
|
||||
reg = <0x00040000 0x00020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition2@60000 {
|
||||
label = "QSEE";
|
||||
reg = <0x00060000 0x00060000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition3@c0000 {
|
||||
label = "CDT";
|
||||
reg = <0x000c0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
partition4@d0000 {
|
||||
label = "DDRPARAMS";
|
||||
reg = <0x000d0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition5@E0000 {
|
||||
label = "APPSBLENV";
|
||||
reg = <0x000e0000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition6@F0000 {
|
||||
label = "APPSBL";
|
||||
reg = <0x000f0000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition7@170000 {
|
||||
label = "ART";
|
||||
reg = <0x00170000 0x00010000>;
|
||||
compatible = "nvmem-cells";
|
||||
read-only;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
precal_art_1000: precal@1000 {
|
||||
reg = <0x1000 0x2f20>;
|
||||
};
|
||||
|
||||
precal_art_5000: precal@5000 {
|
||||
reg = <0x5000 0x2f20>;
|
||||
};
|
||||
};
|
||||
|
||||
partition8@180000 {
|
||||
label = "config";
|
||||
reg = <0x00180000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
partition9@190000 {
|
||||
label = "pot";
|
||||
reg = <0x00190000 0x00010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition10@1a0000 {
|
||||
compatible = "nvmem-cells";
|
||||
label = "dnidata";
|
||||
reg = <0x001a0000 0x00010000>;
|
||||
read-only;
|
||||
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_dnidata_0: macaddr@0 {
|
||||
reg = <0x0 0x6>;
|
||||
};
|
||||
|
||||
macaddr_dnidata_c: macaddr@c {
|
||||
reg = <0xc 0x6>;
|
||||
};
|
||||
};
|
||||
|
||||
partition11@1b0000 {
|
||||
compatible = "denx,fit";
|
||||
label = "firmware";
|
||||
reg = <0x001b0000 0x00e10000>;
|
||||
};
|
||||
|
||||
partition12@fc0000 {
|
||||
label = "rootfs";
|
||||
reg = <0x00fc0000 0x00aa0000>;
|
||||
};
|
||||
|
||||
partition13@1a60000 {
|
||||
label = "rootfs_data";
|
||||
reg = <0x01a60000 0x00070000>;
|
||||
};
|
||||
|
||||
partition14@1ad0000 {
|
||||
label = "language";
|
||||
reg = <0x01ad0000 0x00040000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
pinctrl-0 = <&serial_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&prng {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb2 {
|
||||
dwc3@6000000 {
|
||||
usb2_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb3 {
|
||||
dwc3@8a00000 {
|
||||
usb3_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gmac {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&switch {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&swport1 {
|
||||
status = "okay";
|
||||
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
&swport2 {
|
||||
status = "okay";
|
||||
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
&swport3 {
|
||||
status = "okay";
|
||||
|
||||
label = "lan3";
|
||||
};
|
||||
|
||||
&swport4 {
|
||||
status = "okay";
|
||||
|
||||
label = "lan4";
|
||||
};
|
||||
|
||||
&swport5 {
|
||||
status = "okay";
|
||||
|
||||
label = "lan5";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
|
||||
perst-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
|
||||
wake-gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
|
||||
|
||||
bridge@0,0 {
|
||||
reg = <0x00000000 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
|
||||
wifi@1,0 {
|
||||
compatible = "qcom,ath10k";
|
||||
status = "okay";
|
||||
reg = <0x00010000 0 0 0 0>;
|
||||
ieee80211-freq-limit = <5470000 5875000>;
|
||||
qcom,ath10k-calibration-variant = "Netgear-Orbi-Pro-SRK60";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
nvmem-cell-names = "pre-calibration", "mac-address";
|
||||
nvmem-cells = <&precal_art_1000>, <&macaddr_dnidata_0>;
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
nvmem-cell-names = "pre-calibration", "mac-address";
|
||||
nvmem-cells = <&precal_art_5000>, <&macaddr_dnidata_c>;
|
||||
};
|
||||
@ -817,6 +817,23 @@ define Device/netgear_ex6150v2
|
||||
endef
|
||||
TARGET_DEVICES += netgear_ex6150v2
|
||||
|
||||
define Device/netgear_ex62x0v2
|
||||
$(call Device/DniImage)
|
||||
DEVICE_VENDOR := NETGEAR
|
||||
DEVICE_DTS_CONFIG := config@4
|
||||
NETGEAR_BOARD_ID := EX6200v2series
|
||||
NETGEAR_HW_ID := 29765285+16+0+256+2x2
|
||||
IMAGE_SIZE := 14400k
|
||||
SOC := qcom-ipq4018
|
||||
endef
|
||||
|
||||
define Device/netgear_ex6200v2
|
||||
$(call Device/netgear_ex62x0v2)
|
||||
DEVICE_MODEL := EX6200
|
||||
DEVICE_VARIANT := v2
|
||||
endef
|
||||
TARGET_DEVICES += netgear_ex6200v2
|
||||
|
||||
define Device/netgear_orbi
|
||||
$(call Device/DniImage)
|
||||
SOC := qcom-ipq4019
|
||||
|
||||
Loading…
Reference in New Issue
Block a user