mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-23 23:42:43 +00:00
ipq40xx: add support for Telco X1 Pro
Telco X1 Pro is a Cat12 LTE-A Pro modem router. Vendor firmware is based on a recent version of OpenWrt. Flashing is possible via CLI using sysupgrade -F -n The serial headers allow bootloader and console access Serial setting: 115200 8N1 Brief Specifications: IPQ4019 SoC 32MB flash 512MB RAM 4x gigabit LAN 1x gigabit WAN Dual-band Wave-2 wifi 2x SMA LTE antenna connectors 2x RP-SMA wifi antennas 1x USB 2.0 port 1x Reset button Serial headers installed 1x Nano SIM tray 1x Quectel EM-12G LTE-A Pro modem 1x M.2 slot attached to USB 3.0 1x internal micro SD card slot Signed-off-by: Nicholas Smith <nicholas@nbembedded.com>
This commit is contained in:
Nicholas Smith
Hauke Mehrtens
parent
42626aef67
commit
7ea2f3d6e2
@ -139,7 +139,8 @@ ipq40xx_setup_interfaces()
|
||||
ucidef_add_switch "switch0" \
|
||||
"0u@eth0" "3:lan" "4:lan" "0u@eth1" "5:wan"
|
||||
;;
|
||||
unielec,u4019-32m)
|
||||
unielec,u4019-32m |\
|
||||
tel,x1pro)
|
||||
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
||||
ucidef_add_switch "switch0" \
|
||||
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "0u@eth1" "5:wan"
|
||||
|
||||
@ -0,0 +1,103 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "qcom-ipq4019-x1pro.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
model = "Telco X1 Pro";
|
||||
compatible = "tel,x1pro","qcom,ipq4019";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
pinctrl-0 = <&spi_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
cs-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
|
||||
|
||||
flash@0 {
|
||||
reg = <0>;
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <24000000>;
|
||||
broken-flash-reset;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "0:SBL1";
|
||||
reg = <0x0 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
partition@40000 {
|
||||
label = "0:MIBIB";
|
||||
reg = <0x40000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
partition@60000 {
|
||||
label = "0:QSEE";
|
||||
reg = <0x60000 0x60000>;
|
||||
read-only;
|
||||
};
|
||||
partition@c0000 {
|
||||
label = "0:CDT";
|
||||
reg = <0xc0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
partition@d0000 {
|
||||
label = "0:DDRPARAMS";
|
||||
reg = <0xd0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
partition@e0000 {
|
||||
label = "0:APPSBLENV";
|
||||
reg = <0xe0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
partition@f0000 {
|
||||
label = "0:APPSBL";
|
||||
reg = <0xf0000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
art: partition@170000 {
|
||||
label = "0:ART";
|
||||
reg = <0x170000 0x10000>;
|
||||
read-only;
|
||||
compatible = "nvmem-cells";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
precal_art_1000: precal@1000 {
|
||||
reg = <0x1000 0x2f20>;
|
||||
};
|
||||
|
||||
precal_art_5000: precal@5000 {
|
||||
reg = <0x5000 0x2f20>;
|
||||
};
|
||||
};
|
||||
partition@180000 {
|
||||
compatible = "denx,fit";
|
||||
label = "firmware";
|
||||
reg = <0x180000 0x1e80000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
status = "okay";
|
||||
|
||||
mtd-mac-address = <&art 0x5006>;
|
||||
mtd-mac-address-increment = <2>;
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
status = "okay";
|
||||
|
||||
mtd-mac-address = <&art 0x5006>;
|
||||
mtd-mac-address-increment = <3>;
|
||||
};
|
||||
@ -0,0 +1,228 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
compatible = "tel,x1pro","qcom,ipq4019";
|
||||
aliases {
|
||||
led-boot = &led_status;
|
||||
led-failsafe = &led_status;
|
||||
led-running = &led_status;
|
||||
led-upgrade = &led_status;
|
||||
serial0 = &blsp1_uart1;
|
||||
serial1 = &blsp1_uart2;
|
||||
};
|
||||
|
||||
soc {
|
||||
|
||||
rng@22000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
mdio@90000 {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
reset-gpios = <&tlmm 47 GPIO_ACTIVE_LOW>;
|
||||
reset-delay-us = <2000>;
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
usb2@60f8800 {
|
||||
status = "okay";
|
||||
|
||||
dwc3@6000000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
usb3@8af8800 {
|
||||
status = "okay";
|
||||
|
||||
dwc3@8a00000 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-0 = <&led_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
led_status: status {
|
||||
label = "green:status";
|
||||
gpios = <&tlmm 68 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
pinctrl-0 = <&serial_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_uart2 {
|
||||
pinctrl-0 = <&serial_1_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
mdio_pins: mdio_pinmux {
|
||||
mux_1 {
|
||||
pins = "gpio6";
|
||||
function = "mdio";
|
||||
bias-pull-up;
|
||||
};
|
||||
mux_2 {
|
||||
pins = "gpio7";
|
||||
function = "mdc";
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
serial_0_pins: serial0-pinmux {
|
||||
mux {
|
||||
pins = "gpio16", "gpio17";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
serial_1_pins: serial1_pinmux {
|
||||
mux {
|
||||
pins = "gpio8", "gpio9";
|
||||
function = "blsp_uart1";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_0_pins: spi_0_pinmux {
|
||||
pinmux {
|
||||
function = "blsp_spi0";
|
||||
pins = "gpio13", "gpio14", "gpio15";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
pinmux_cs {
|
||||
function = "gpio";
|
||||
pins = "gpio12";
|
||||
drive-strength = <2>;
|
||||
bias-disable;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
|
||||
led_pins: led_pinmux {
|
||||
mux {
|
||||
function = "gpio";
|
||||
pins = "gpio68";
|
||||
bias-disabled;
|
||||
output-low;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb3_ss_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb2_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
nvmem-cell-names = "pre-calibration";
|
||||
nvmem-cells = <&precal_art_1000>;
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
nvmem-cell-names = "pre-calibration";
|
||||
nvmem-cells = <&precal_art_5000>;
|
||||
};
|
||||
@ -963,6 +963,18 @@ define Device/teltonika_rutx10
|
||||
endef
|
||||
TARGET_DEVICES += teltonika_rutx10
|
||||
|
||||
define Device/tel_x1pro
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := Telco
|
||||
DEVICE_MODEL := X1 Pro
|
||||
SOC := qcom-ipq4019
|
||||
KERNEL_SIZE := 4096k
|
||||
IMAGE_SIZE := 31232k
|
||||
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
||||
DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
|
||||
endef
|
||||
TARGET_DEVICES += tel_x1pro
|
||||
|
||||
define Device/unielec_u4019-32m
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := Unielec
|
||||
|
||||
@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
|
||||
--- a/arch/arm/boot/dts/Makefile
|
||||
+++ b/arch/arm/boot/dts/Makefile
|
||||
@@ -903,11 +903,74 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
@@ -903,11 +903,75 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
qcom-apq8074-dragonboard.dtb \
|
||||
qcom-apq8084-ifc6540.dtb \
|
||||
qcom-apq8084-mtp.dtb \
|
||||
@ -71,6 +71,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
+ qcom-ipq4019-rtl30vw.dtb \
|
||||
+ qcom-ipq4019-srr60.dtb \
|
||||
+ qcom-ipq4019-srs60.dtb \
|
||||
+ qcom-ipq4019-x1pro.dtb \
|
||||
+ qcom-ipq4019-u4019-32m.dtb \
|
||||
+ qcom-ipq4019-wpj419.dtb \
|
||||
+ qcom-ipq4019-wtr-m2133hp.dtb \
|
||||
|
||||
Loading…
Reference in New Issue
Block a user