ipq40xx: add MikroTik cAP ac support

This adds support for the MikroTik RouterBOARD RBcAPGi-5acD2nD
(cAP ac), a  indoor dual band, dual-radio 802.11ac wireless AP, two
10/100/1000 Mbps Ethernet ports.

See https://mikrotik.com/product/cap_ac for more info.

Specifications:
 - SoC: Qualcomm Atheros IPQ4018
 - RAM: 128 MB
 - Storage: 16 MB NOR
 - Wireless:
   · Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
   · Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
 - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 2x 1000/100/10 port,
   PoE in and passive PoE out

Unsupported:
 - PoE out

Installation:
Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"

Signed-off-by: Alar Aun <alar.aun@gmail.com>

package/firmware/ipq-wifi/Makefile

@@ -45,6 +45,7 @@ ALLWIFIBOARDS:= \
 	linksys_ea8300 \
 	linksys_mr8300-v0 \
 	luma_wrtq-329acn \
+	mikrotik_cap-ac \
 	mikrotik_hap-ac2 \
 	mikrotik_hap-ac3 \
 	mikrotik_sxtsq-5-ac \
@@ -135,6 +136,7 @@ $(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300))
 $(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
 $(eval $(call generate-ipq-wifi-package,linksys_mr8300-v0,Linksys MR8300))
 $(eval $(call generate-ipq-wifi-package,luma_wrtq-329acn,Luma WRTQ-329ACN))
+$(eval $(call generate-ipq-wifi-package,mikrotik_cap-ac,Mikrotik cAP ac))
 $(eval $(call generate-ipq-wifi-package,mikrotik_hap-ac2,Mikrotik hAP ac2))
 $(eval $(call generate-ipq-wifi-package,mikrotik_hap-ac3,Mikrotik hAP ac3))
 $(eval $(call generate-ipq-wifi-package,mikrotik_sxtsq-5-ac,MikroTik SXTsq 5 ac))

target/linux/ipq40xx/base-files/etc/board.d/01_leds

@@ -52,6 +52,13 @@ engenius,ens620ext)
 	ucidef_set_led_netdev "lan1" "LAN1" "green:lan1" "eth0"
 	ucidef_set_led_netdev "lan2" "LAN2" "green:lan2" "eth1"
 	;;
+mikrotik,cap-ac)
+	ucidef_set_led_default "power" "POWER" "blue:power" "1"
+	ucidef_set_led_default "user" "USER" "green:user" "0"
+	ucidef_set_led_switch "eth1" "ETH1" "green:eth1" "switch0" "0x20"
+	ucidef_set_led_switch "eth2" "ETH2" "green:eth2" "switch0" "0x10"
+	ucidef_set_led_wlan "wlan2g" "WLAN2G" "green:wlan2g" "phy0tpt"
+	ucidef_set_led_wlan "wlan5g" "WLAN5G" "green:wlan5g" "phy1tpt"
 mikrotik,hap-ac3)
 	ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth1"
 	ucidef_set_led_switch "lan1" "LAN1" "green:lan1" "switch0" "0x10"

target/linux/ipq40xx/base-files/etc/board.d/02_network

@@ -50,6 +50,10 @@ ipq40xx_setup_interfaces()
 	openmesh,a62)
 		ucidef_set_interfaces_lan_wan "eth1" "eth0"
 		;;
+	mikrotik,cap-ac)
+		ucidef_add_switch "switch0" \
+			"0t@eth0" "4:lan" "5:wan"
+		;;
 	asus,rt-ac42u|\
 	asus,rt-ac58u|\
 	mikrotik,hap-ac2|\
@@ -190,6 +194,7 @@ ipq40xx_setup_macs()
 		wan_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
 		lan_mac=$(macaddr_add "$wan_mac" 1)
 		;;
+	mikrotik,cap-ac |\
 	mikrotik,hap-ac2|\
 	mikrotik,hap-ac3)
 		wan_mac=$(cat /sys/firmware/mikrotik/hard_config/mac_base)

target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches

@@ -18,6 +18,9 @@ cilab,meshpoint-one)
 compex,wpj428)
 	ucidef_add_gpio_switch "sim_card_select" "SIM card select" "3" "0"
 	;;
+mikrotik,cap-ac)
+	ucidef_add_gpio_switch "poe_passtrough" "POE passtrough enable" "414" "0"
+	;;
 mikrotik,hap-ac3)
 	ucidef_add_gpio_switch "poe_passtrough" "PoE Passthrough" "452" "0"
 	;;

target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata

@@ -112,6 +112,7 @@ case "$FIRMWARE" in
 		caldata_valid "202f" || caldata_extract "ART" 0x1000 0x2f20
 		ath10k_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66) 2)
 		;;
+	mikrotik,cap-ac |\
 	mikrotik,hap-ac2 |\
 	mikrotik,hap-ac3)
 		wlan_data="/sys/firmware/mikrotik/hard_config/wlan_data"
@@ -190,6 +191,7 @@ case "$FIRMWARE" in
 		caldata_valid "202f" || caldata_extract "ART" 0x5000 0x2f20
 		ath10k_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66) 3)
 		;;
+	mikrotik,cap-ac |\
 	mikrotik,hap-ac2 |\
 	mikrotik,hap-ac3 |\
 	mikrotik,sxtsq-5-ac)

target/linux/ipq40xx/base-files/lib/upgrade/platform.sh

@@ -138,6 +138,7 @@ platform_do_upgrade() {
 		CI_KERNPART="part.safe"
 		nand_do_upgrade "$1"
 		;;
+	mikrotik,cap-ac|\
 	mikrotik,hap-ac2|\
 	mikrotik,lhgg-60ad|\
 	mikrotik,sxtsq-5-ac)

target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-cap-ac.dts

@@ -0,0 +1,250 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2020, Robert Marko <robimarko@gmail.com> */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+	model = "MikroTik cAP ac";
+	compatible = "mikrotik,cap-ac";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x08000000>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	aliases {
+		led-boot = &led_user;
+		led-failsafe = &led_user;
+		led-running = &led_user;
+		led-upgrade = &led_user;
+	};
+
+	soc {
+		rng@22000 {
+			status = "okay";
+		};
+
+		counter@4a1000 {
+			compatible = "qcom,qca-gcnt";
+			reg = <0x4a1000 0x4>;
+		};
+
+		tcsr@1949000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1949000 0x100>;
+			qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+		};
+
+		ess_tcsr@1953000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1953000 0x1000>;
+			qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+		};
+
+		tcsr@1957000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1957000 0x100>;
+			qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+		};
+
+		crypto@8e3a000 {
+			status = "okay";
+		};
+
+		watchdog@b017000 {
+			status = "okay";
+		};
+
+		ess-switch@c000000 {
+			status = "okay";
+		};
+
+		edma@c080000 {
+			status = "okay";
+			qcom,poll_required = <0>;
+			qcom,num_gmac = <1>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		mode {
+			label = "mode";
+			gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_LIGHTS_TOGGLE>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		power {
+			label = "blue:power";
+			gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+
+		led_user: user {
+			label = "green:user";
+			gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+			panic-indicator;
+		};
+
+		wlan2g {
+			label = "green:wlan2g";
+			gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan5g {
+			label = "green:wlan5g";
+			gpios = <&tlmm 58 GPIO_ACTIVE_HIGH>;
+		};
+
+		eth1 {
+			label = "green:eth1";
+			gpios = <&ethphy4 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		eth2 {
+			label = "green:eth2";
+			gpios = <&ethphy3 1 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&tlmm {
+	serial_pins: serial_pinmux {
+		mux {
+			pins = "gpio60", "gpio61";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	spi_0_pins: spi_0_pinmux {
+		pin {
+			function = "blsp_spi0";
+			pins = "gpio55", "gpio56", "gpio57";
+			drive-strength = <2>;
+			bias-disable;
+		};
+		pin_cs {
+			function = "gpio";
+			pins = "gpio54";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp1_spi1 {
+	status = "okay";
+
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		reg = <0>;
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <40000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "Qualcomm";
+				reg = <0x0 0x80000>;
+				read-only;
+			};
+
+			partition@80000 {
+				compatible = "mikrotik,routerboot-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				label = "RouterBoot";
+				reg = <0x80000 0x80000>;
+				read-only;
+
+				hard_config {
+					read-only;
+				};
+
+				dtb_config {
+					read-only;
+				};
+
+				soft_config {
+				};
+			};
+
+			partition@100000 {
+				compatible = "mikrotik,minor";
+				label = "firmware";
+				reg = <0x100000 0xf00000>;
+			};
+		};
+	};
+};
+
+&blsp1_uart1 {
+	status = "okay";
+
+	pinctrl-0 = <&serial_pins>;
+	pinctrl-names = "default";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&mdio {
+	status = "okay";
+};
+
+&gmac0 {
+	vlan_tag = <0 0x3f>;
+};
+
+&ethphy3 {
+	gpio-controller;
+	#gpio-cells = <2>;
+};
+
+&ethphy4 {
+	gpio-controller;
+	#gpio-cells = <2>;
+};
+
+&wifi0 {
+	status = "okay";
+
+	qcom,ath10k-calibration-variant = "MikroTik-cAP-ac";
+};
+
+&wifi1 {
+	status = "okay";
+
+	qcom,ath10k-calibration-variant = "MikroTik-cAP-ac";
+};

target/linux/ipq40xx/image/mikrotik.mk

@@ -20,6 +20,15 @@ define Device/mikrotik_nand
 	IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata
 endef
 
+define Device/mikrotik_cap-ac
+	$(call Device/mikrotik_nor)
+	DEVICE_MODEL := cAP ac
+	SOC := qcom-ipq4018
+	DEVICE_PACKAGES := ipq-wifi-mikrotik_cap-ac -kmod-ath10k-ct \
+		kmod-ath10k-ct-smallbuffers
+endef
+TARGET_DEVICES += mikrotik_cap-ac
+
 define Device/mikrotik_hap-ac2
 	$(call Device/mikrotik_nor)
 	DEVICE_MODEL := hAP ac2

target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch

@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -902,11 +902,72 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -902,11 +902,73 @@ dtb-$(CONFIG_ARCH_QCOM) += \
  	qcom-apq8074-dragonboard.dtb \
  	qcom-apq8084-ifc6540.dtb \
  	qcom-apq8084-mtp.dtb \
@@ -31,6 +31,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 +	qcom-ipq4018-gl-ap1300.dtb \
 +	qcom-ipq4018-jalapeno.dtb \
 +	qcom-ipq4018-meshpoint-one.dtb \
++	qcom-ipq4018-cap-ac.dtb \
 +	qcom-ipq4018-hap-ac2.dtb \
 +	qcom-ipq4018-sxtsq-5-ac.dtb \
 +	qcom-ipq4018-nbg6617.dtb \