From 566bd9c41d46956c9f35ab54b677a570a4f9dec5 Mon Sep 17 00:00:00 2001 From: Shymon Samsel Date: Fri, 13 Dec 2024 05:59:04 -0500 Subject: [PATCH] ipq807x: add support for TP-Link EAP620 HD v1 Specifications: * SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 1.4 GHz) * Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13) * Serial Port: 3v3 TTL 115200n8 * Wi-Fi: QCA5054 (4x4 5 GHz 802.11ax) * Wi-Fi: QCN5024 (2x2 2.4 GHz 802.11b/g/n/ax) * Ethernet: AR8031 (10/100/1000BASE-T) * Flash: Winbond W29N01HZSINF (128 MiB) * LEDs: 1x Blue Status (GPIO 42 Active High) * Buttons: 1x Reset (GPIO 50 Active Low) Installation Instructions (Serial+TFTP): 1. Solder 4 pin header to JP1 and bridge pads of R58 and R62. 2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2, and 3 respectively. Be sure to crossover TX and RX. 3. Copy RAM firmware openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb to a TFTP server's root that is in the same subnet as your AP. 4. Power up the AP hold Ctrl+B in the serial console (115200n8) until autoboot is halted. 5. Run the following commands in the U-boot prompt: # setenv serverip # setenv ipaddr # tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb # bootm You may need to type Ctrl+C and Enter before running these commands to clear invisible characters from the buffer. 6. Run the following command in a terminal to copy the sysupgrade image to be installed (check IP address): $ scp -O openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/ 7. Activate the OpenWrt serial console and run the following commands: # cd /tmp # sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin 8. The AP will reboot and OpenWrt will be successfully installed. Known Issues: * 5GHz radio instability (upstream current ath11k build bug maybe?) Device support directly followed from EAP660HDv1 support Links: #15832 Signed-off-by: Shymon Samsel --- .../uboot-envtools/files/qualcommax_ipq807x | 1 + package/firmware/ipq-wifi/Makefile | 2 + .../boot/dts/qcom/ipq8072-eap620hd-v1.dts | 142 ++++++++++++++++++ target/linux/qualcommax/image/ipq807x.mk | 14 ++ .../ipq807x/base-files/etc/board.d/02_network | 2 + .../etc/hotplug.d/firmware/11-ath11k-caldata | 1 + .../lib/preinit/09_mount_factory_data | 1 + .../base-files/lib/upgrade/platform.sh | 1 + 8 files changed, 164 insertions(+) create mode 100644 target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-eap620hd-v1.dts diff --git a/package/boot/uboot-envtools/files/qualcommax_ipq807x b/package/boot/uboot-envtools/files/qualcommax_ipq807x index f5fb07a4db0..b0088125c4c 100644 --- a/package/boot/uboot-envtools/files/qualcommax_ipq807x +++ b/package/boot/uboot-envtools/files/qualcommax_ipq807x @@ -39,6 +39,7 @@ linksys,mx8500) ;; netgear,sxr80|\ netgear,sxs80|\ +tplink,eap620hd-v1|\ tplink,eap660hd-v1) idx="$(find_mtd_index 0:appsblenv)" [ -n "$idx" ] && \ diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index fe17484d851..1cb6cd6863a 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -55,6 +55,7 @@ ALLWIFIBOARDS:= \ redmi_ax6 \ skspruce_wia3300-20 \ spectrum_sax1v1k \ + tplink_eap620hd-v1 \ tplink_eap660hd-v1 \ wallys_dr40x9 \ xiaomi_ax3600 \ @@ -184,6 +185,7 @@ $(eval $(call generate-ipq-wifi-package,prpl_haze,prpl Haze)) $(eval $(call generate-ipq-wifi-package,redmi_ax6,Redmi AX6)) $(eval $(call generate-ipq-wifi-package,skspruce_wia3300-20,SKSpruce WIA3300-20)) $(eval $(call generate-ipq-wifi-package,spectrum_sax1v1k,Spectrum SAX1V1K)) +$(eval $(call generate-ipq-wifi-package,tplink_eap620hd-v1,TP-Link EAP620 HD v1)) $(eval $(call generate-ipq-wifi-package,tplink_eap660hd-v1,TP-Link EAP660 HD v1)) $(eval $(call generate-ipq-wifi-package,wallys_dr40x9,Wallys DR40X9)) $(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600)) diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-eap620hd-v1.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-eap620hd-v1.dts new file mode 100644 index 00000000000..05621892e6e --- /dev/null +++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8072-eap620hd-v1.dts @@ -0,0 +1,142 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR BSD-2-Clause + +/dts-v1/; + +#include "ipq8074.dtsi" +#include "ipq8074-hk-cpu.dtsi" +#include "ipq8074-ess.dtsi" +#include +#include +#include + +/ { + model = "TP-Link EAP620 HD v1"; + compatible = "tplink,eap620hd-v1", "qcom,ipq8074"; + + aliases { + serial0 = &blsp1_uart5; + led-boot = &led_status_blue; + led-failsafe = &led_status_blue; + led-running = &led_status_blue; + led-upgrade = &led_status_blue; + }; + + chosen { + stdout-path = "serial0,115200n8"; + bootargs-append = " root=/dev/ubiblock0_1"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 50 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_status_blue: status-blue { + function = LED_FUNCTION_STATUS; + gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>; + color = ; + }; + }; +}; + +&blsp1_uart5 { + status = "okay"; +}; + +&tlmm { + mdio_pins: mdio-pins { + mdc { + pins = "gpio68"; + function = "mdc"; + drive-strength = <8>; + bias-pull-up; + }; + + mdio { + pins = "gpio69"; + function = "mdio"; + drive-strength = <8>; + bias-pull-up; + }; + }; +}; + +&mdio { + status = "okay"; + #size-cells = <1>; + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>; + + ar8031: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <4>; + }; +}; + +&dp6 { + status = "okay"; + phy-handle = <&ar8031>; + label = "lan"; +}; + +&switch { + status = "okay"; + switch_lan_bmp = ; + switch_mac_mode2 = ; + + qcom,port_phyinfo { + port@6 { + phy_address = <4>; + port_id = <6>; + }; + }; +}; + +&edma { + status = "okay"; +}; + +&prng { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&crypto { + status = "okay"; +}; + +&qpic_bam { + status = "okay"; +}; + +&qpic_nand { + status = "okay"; + + nand@0 { + reg = <0>; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-bus-width = <8>; + + partitions { + compatible = "qcom,smem-part"; + }; + }; +}; + +&wifi { + status = "okay"; + qcom,ath11k-calibration-variant = "TP-Link-EAP620-HD-v1"; +}; diff --git a/target/linux/qualcommax/image/ipq807x.mk b/target/linux/qualcommax/image/ipq807x.mk index ff6963405c6..4a194c6cb7b 100644 --- a/target/linux/qualcommax/image/ipq807x.mk +++ b/target/linux/qualcommax/image/ipq807x.mk @@ -346,6 +346,20 @@ define Device/spectrum_sax1v1k endef TARGET_DEVICES += spectrum_sax1v1k +define Device/tplink_eap620hd-v1 + $(call Device/FitImage) + $(call Device/UbiFit) + DEVICE_VENDOR := TP-Link + DEVICE_MODEL := EAP620 HD + DEVICE_VARIANT := v1 + BLOCKSIZE := 128k + PAGESIZE := 2048 + SOC := ipq8072 + DEVICE_PACKAGES := ipq-wifi-tplink_eap620hd-v1 + TPLINK_SUPPORT_STRING := SupportList:\r\nEAP620 HD(TP-Link|UN|AX1800-D):1.0\r\n +endef +TARGET_DEVICES += tplink_eap620hd-v1 + define Device/tplink_eap660hd-v1 $(call Device/FitImage) $(call Device/UbiFit) diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network index 437581d0011..012288fedc5 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network +++ b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network @@ -60,6 +60,7 @@ ipq807x_setup_interfaces() qnap,301w) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 10g-2" "10g-1" ;; + tplink,eap620hd-v1|\ tplink,eap660hd-v1) ucidef_set_interface_lan "lan" "dhcp" ;; @@ -92,6 +93,7 @@ ipq807x_setup_macs() lan_mac=$(macaddr_add $label_mac 1) wan_mac=$label_mac ;; + tplink,eap620hd-v1|\ tplink,eap660hd-v1) label_mac=$(get_mac_binary /tmp/factory_data/default-mac 0) lan_mac=$label_mac diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata index 2e741f04484..7496138a26f 100644 --- a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata +++ b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata @@ -80,6 +80,7 @@ case "$FIRMWARE" in spectrum,sax1v1k) caldata_extract_mmc "0:ART" 0x1000 0x20000 ;; + tplink,eap620hd-v1|\ tplink,eap660hd-v1) caldata_from_file "/tmp/factory_data/radio" 0 0x20000 label_mac=$(get_mac_binary /tmp/factory_data/default-mac 0) diff --git a/target/linux/qualcommax/ipq807x/base-files/lib/preinit/09_mount_factory_data b/target/linux/qualcommax/ipq807x/base-files/lib/preinit/09_mount_factory_data index 59fde529d3c..2563202a1a2 100644 --- a/target/linux/qualcommax/ipq807x/base-files/lib/preinit/09_mount_factory_data +++ b/target/linux/qualcommax/ipq807x/base-files/lib/preinit/09_mount_factory_data @@ -7,6 +7,7 @@ preinit_mount_factory_data() { . /lib/functions/system.sh case $(board_name) in + tplink,eap620hd-v1|\ tplink,eap660hd-v1) mtd_path=$(find_mtd_chardev "factory_data") ubiattach --dev-path="$mtd_path" --devn=1 diff --git a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh index 70657629fcc..5e339ae1ecc 100644 --- a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh +++ b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh @@ -214,6 +214,7 @@ platform_do_upgrade() { CI_DATAPART="rootfs_data" emmc_do_upgrade "$1" ;; + tplink,eap620hd-v1|\ tplink,eap660hd-v1) tplink_do_upgrade "$1" ;;