mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-19 13:48:06 +00:00
ath79: add support for KuWfi CPE830(D) / YunCore CPE830(D)
Short specification:
* 650/600/216 MHz (CPU/DDR/AHB)
* 2x 10/100 Mbps Ethernet, passive PoE support
* 64 MB of RAM (DDR2)
* 16 MB of FLASH
* 2T2R 2.4 GHz with external PA, up to 30 dBm (1000mW)
* 2x internal 14 dBi antennas
* 8x LED, 1x button
* No UART on PCB on some versions
* Display panel with 2x buttons (F/N) not supported (and not relevant in OpenWrt)-
Flash instructions
* Connect PC with 192.168.0.141 to WAN port
* Install a TFTP server on your PC ('atftp' is doing the job for instance)
* Copy your firmware in the TFTP folder as upgrade.bin
* Power up device pushing the 'reset' button
* The device shall upload upgrade.bin, install it and reboot
* Device shall be booting on 192.168.1.1 as default
Signed-off-by: Joan Moreau <jom@grosjo.net>
This commit is contained in:
Joan Moreau
parent
8a7239009c
commit
3bd05b763c
153
target/linux/ath79/dts/qca9533_yuncore_cpe830.dts
Normal file
153
target/linux/ath79/dts/qca9533_yuncore_cpe830.dts
Normal file
@ -0,0 +1,153 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qca953x.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
compatible = "yuncore,cpe830", "qca,qca9533";
|
||||
model = "YunCore/KuWfi CPE830(D)";
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
aliases {
|
||||
label-mac-device = &wmac;
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_power;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power: power {
|
||||
function = LED_FUNCTION_POWER;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
wlan {
|
||||
function = LED_FUNCTION_WLAN;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
link1 {
|
||||
label = "green:signal0";
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
link2 {
|
||||
label = "green:signal1";
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
link3 {
|
||||
label = "green:signal2";
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
link4 {
|
||||
label = "green:signal3";
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x040000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x050000 0xfa0000>;
|
||||
};
|
||||
|
||||
partition@ff0000 {
|
||||
label = "art";
|
||||
reg = <0xff0000 0x010000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_art_0: macaddr@0 {
|
||||
reg = <0x0 0x6>;
|
||||
};
|
||||
|
||||
macaddr_art_6: macaddr@6 {
|
||||
reg = <0x6 0x6>;
|
||||
};
|
||||
|
||||
cal_art_1000: calibration@1000 {
|
||||
reg = <0x1000 0x440>;
|
||||
};
|
||||
|
||||
macaddr_art_wmac: macaddr@1002 {
|
||||
reg = <0x1002 0x6>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
phy-handle = <&swphy4>;
|
||||
nvmem-cells = <&macaddr_art_0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
ð1 {
|
||||
status = "okay";
|
||||
nvmem-cells = <&macaddr_art_6>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
nvmem-cells = <&cal_art_1000>;
|
||||
nvmem-cell-names = "calibration";
|
||||
};
|
||||
@ -545,6 +545,13 @@ yuncore,a770)
|
||||
ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth1"
|
||||
ucidef_set_led_switch "lan" "LAN" "green:lan" "switch0" "0x10"
|
||||
;;
|
||||
yuncore,cpe830)
|
||||
ucidef_set_rssimon "wlan0" "200000" "1"
|
||||
ucidef_set_led_rssi "wifi_low" "WIFILOW" "green:signal0" "wlan0" "1" "100"
|
||||
ucidef_set_led_rssi "wifi_mediumlow" "WIFIMEDIUMLOW" "green:signal1" "wlan0" "26" "100"
|
||||
ucidef_set_led_rssi "wifi_mediumhigh" "WIFIMEDIUMHIGH" "green:signal2" "wlan0" "51" "100"
|
||||
ucidef_set_led_rssi "wifi_high" "WIFIHIGH" "green:signal3" "wlan0" "76" "100"
|
||||
;;
|
||||
zbtlink,zbt-wd323)
|
||||
ucidef_set_led_switch "lan1" "LAN1" "orange:lan1" "switch0" "0x10"
|
||||
ucidef_set_led_switch "lan2" "LAN2" "orange:lan2" "switch0" "0x08"
|
||||
|
||||
@ -3307,6 +3307,19 @@ define Device/yuncore_xd3200
|
||||
endef
|
||||
TARGET_DEVICES += yuncore_xd3200
|
||||
|
||||
define Device/yuncore_cpe830
|
||||
SOC := qca9533
|
||||
DEVICE_VENDOR := YunCore
|
||||
DEVICE_MODEL := CPE830(D)
|
||||
DEVICE_ALT0_VENDOR = KuWfi
|
||||
DEVICE_ALT0_MODEL = CPE830(D)
|
||||
IMAGE_SIZE := 16000k
|
||||
IMAGES += tftp.bin
|
||||
IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
|
||||
DEVICE_PACKAGES := rssileds kmod-leds-gpio kmod-ledtrig-gpio -swconfig
|
||||
endef
|
||||
TARGET_DEVICES += yuncore_cpe830
|
||||
|
||||
define Device/yuncore_xd4200
|
||||
SOC := qca9563
|
||||
DEVICE_VENDOR := YunCore
|
||||
|
||||
Loading…
Reference in New Issue
Block a user