ixp4xx 2.6.26 support

SVN-Revision: 11583
This commit is contained in:
Imre Kaloz 2008-06-26 13:59:15 +00:00
parent a425a7506c
commit 3465540af9
39 changed files with 7740 additions and 0 deletions

View File

@ -34,6 +34,7 @@ CONFIG_ARCH_IXP4XX=y
# CONFIG_ARCH_NS9XXX is not set
# CONFIG_ARCH_OMAP is not set
# CONFIG_ARCH_ORION is not set
# CONFIG_ARCH_ORION5X is not set
# CONFIG_ARCH_PNX4008 is not set
# CONFIG_ARCH_PRPMC1100 is not set
# CONFIG_ARCH_PXA is not set

View File

@ -0,0 +1,559 @@
From: Rod Whitby <rod@whitby.id.au>
Subject: [PATCH] ixp4xx: Add support for the Freecom FSG-3 board (Patch #4874)
The Freecom-FSG3 is a small network-attached-storage device with the
following feature set:
* Intel IXP422
* 4MB Flash (ixp4xx flash driver)
* 64MB RAM
* 4 USB 2.0 host ports (ehci and ohci drivers)
* 1 WAN (eth1) and 3 LAN (eth0) ethernet ports
* Supported by the open source ixp4xx ethernet driver
* Via VT6421 disk controller (libata and sata-via drivers)
* Internal hard disk (PATA supported, SATA not yet supported)
* External SATA port (not yet supported)
* ISL1208 RTC chip
* Winbond 83782 temp sensor and fan controller
* MiniPCI slot
The ixp4xx_defconfig is also updated to support this device (the
leds-fsg driver is to be submitted separately via the leds tree after
this initial support is merged, as it depends on header gpio defines).
Signed-off-by: Rod Whitby <rod@whitby.id.au>
PATCH FOLLOWS
KernelVersion: v2.6.25-rc6-74-g264e3e8
---
Updated to correct all issues found by RMK.
The front power button calls ctrl_alt_del() and the rear reset button
now calls machine_restart() directly.
arch/arm/configs/ixp4xx_defconfig | 9 +-
arch/arm/mach-ixp4xx/Kconfig | 9 +
arch/arm/mach-ixp4xx/Makefile | 2 +
arch/arm/mach-ixp4xx/fsg-pci.c | 71 ++++++++
arch/arm/mach-ixp4xx/fsg-setup.c | 276 ++++++++++++++++++++++++++++++++
include/asm-arm/arch-ixp4xx/fsg.h | 50 ++++++
include/asm-arm/arch-ixp4xx/hardware.h | 1 +
include/asm-arm/arch-ixp4xx/irqs.h | 7 +
8 files changed, 421 insertions(+), 4 deletions(-)
create mode 100644 arch/arm/mach-ixp4xx/fsg-pci.c
create mode 100644 arch/arm/mach-ixp4xx/fsg-setup.c
create mode 100644 include/asm-arm/arch-ixp4xx/fsg.h
--- a/arch/arm/configs/ixp4xx_defconfig
+++ b/arch/arm/configs/ixp4xx_defconfig
@@ -165,6 +165,7 @@
CONFIG_MACH_NAS100D=y
CONFIG_MACH_DSMG600=y
CONFIG_ARCH_IXDP4XX=y
+CONFIG_MACH_FSG=y
CONFIG_CPU_IXP46X=y
CONFIG_CPU_IXP43X=y
CONFIG_MACH_GTWX5715=y
@@ -770,7 +771,7 @@
# CONFIG_SATA_SIL24 is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
-# CONFIG_SATA_VIA is not set
+CONFIG_SATA_VIA=y
# CONFIG_SATA_VITESSE is not set
# CONFIG_SATA_INIC162X is not set
# CONFIG_PATA_ALI is not set
@@ -1143,7 +1144,7 @@
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_VT8231 is not set
-# CONFIG_SENSORS_W83781D is not set
+CONFIG_SENSORS_W83781D=y
# CONFIG_SENSORS_W83791D is not set
# CONFIG_SENSORS_W83792D is not set
# CONFIG_SENSORS_W83793 is not set
@@ -1334,8 +1335,8 @@
#
# LED drivers
#
-# CONFIG_LEDS_IXP4XX is not set
CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_FSG=y
#
# LED Triggers
@@ -1367,7 +1368,7 @@
# CONFIG_RTC_DRV_DS1672 is not set
# CONFIG_RTC_DRV_MAX6900 is not set
# CONFIG_RTC_DRV_RS5C372 is not set
-# CONFIG_RTC_DRV_ISL1208 is not set
+CONFIG_RTC_DRV_ISL1208=y
CONFIG_RTC_DRV_X1205=y
CONFIG_RTC_DRV_PCF8563=y
# CONFIG_RTC_DRV_PCF8583 is not set
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -125,6 +125,15 @@
depends on ARCH_IXDP425 || MACH_IXDP465 || MACH_KIXRP435
default y
+config MACH_FSG
+ bool
+ prompt "Freecom FSG-3"
+ select PCI
+ help
+ Say 'Y' here if you want your kernel to support Freecom's
+ FSG-3 device. For more information on this platform,
+ see http://www.nslu2-linux.org/wiki/FSG3/HomePage
+
#
# Certain registers and IRQs are only enabled if supporting IXP465 CPUs
#
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
@@ -15,6 +15,7 @@
obj-pci-$(CONFIG_MACH_DSMG600) += dsmg600-pci.o
obj-pci-$(CONFIG_MACH_GATEWAY7001) += gateway7001-pci.o
obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o
+obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o
obj-y += common.o
@@ -28,6 +29,7 @@
obj-$(CONFIG_MACH_DSMG600) += dsmg600-setup.o
obj-$(CONFIG_MACH_GATEWAY7001) += gateway7001-setup.o
obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o
+obj-$(CONFIG_MACH_FSG) += fsg-setup.o
obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o
obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/fsg-pci.c
@@ -0,0 +1,71 @@
+/*
+ * arch/arch/mach-ixp4xx/fsg-pci.c
+ *
+ * FSG board-level PCI initialization
+ *
+ * Author: Rod Whitby <rod@whitby.id.au>
+ * Maintainer: http://www.nslu2-linux.org/
+ *
+ * based on ixdp425-pci.c:
+ * Copyright (C) 2002 Intel Corporation.
+ * Copyright (C) 2003-2004 MontaVista Software, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+
+#include <asm/mach/pci.h>
+#include <asm/mach-types.h>
+
+void __init fsg_pci_preinit(void)
+{
+ set_irq_type(IRQ_FSG_PCI_INTA, IRQT_LOW);
+ set_irq_type(IRQ_FSG_PCI_INTB, IRQT_LOW);
+ set_irq_type(IRQ_FSG_PCI_INTC, IRQT_LOW);
+
+ ixp4xx_pci_preinit();
+}
+
+static int __init fsg_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+ static int pci_irq_table[FSG_PCI_IRQ_LINES] = {
+ IRQ_FSG_PCI_INTC,
+ IRQ_FSG_PCI_INTB,
+ IRQ_FSG_PCI_INTA,
+ };
+
+ int irq = -1;
+ slot = slot - 11;
+
+ if (slot >= 1 && slot <= FSG_PCI_MAX_DEV &&
+ pin >= 1 && pin <= FSG_PCI_IRQ_LINES)
+ irq = pci_irq_table[(slot - 1)];
+ printk(KERN_INFO "%s: Mapped slot %d pin %d to IRQ %d\n",
+ __func__, slot, pin, irq);
+
+ return irq;
+}
+
+struct hw_pci fsg_pci __initdata = {
+ .nr_controllers = 1,
+ .preinit = fsg_pci_preinit,
+ .swizzle = pci_std_swizzle,
+ .setup = ixp4xx_setup,
+ .scan = ixp4xx_scan_bus,
+ .map_irq = fsg_map_irq,
+};
+
+int __init fsg_pci_init(void)
+{
+ if (machine_is_fsg())
+ pci_common_init(&fsg_pci);
+ return 0;
+}
+
+subsys_initcall(fsg_pci_init);
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/fsg-setup.c
@@ -0,0 +1,276 @@
+/*
+ * arch/arm/mach-ixp4xx/fsg-setup.c
+ *
+ * FSG board-setup
+ *
+ * Copyright (C) 2008 Rod Whitby <rod@whitby.id.au>
+ *
+ * based on ixdp425-setup.c:
+ * Copyright (C) 2003-2004 MontaVista Software, Inc.
+ * based on nslu2-power.c
+ * Copyright (C) 2005 Tower Technologies
+ *
+ * Author: Rod Whitby <rod@whitby.id.au>
+ * Maintainers: http://www.nslu2-linux.org/
+ *
+ */
+
+#include <linux/if_ether.h>
+#include <linux/irq.h>
+#include <linux/serial.h>
+#include <linux/serial_8250.h>
+#include <linux/leds.h>
+#include <linux/reboot.h>
+#include <linux/i2c.h>
+#include <linux/i2c-gpio.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+
+static struct flash_platform_data fsg_flash_data = {
+ .map_name = "cfi_probe",
+ .width = 2,
+};
+
+static struct resource fsg_flash_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device fsg_flash = {
+ .name = "IXP4XX-Flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &fsg_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &fsg_flash_resource,
+};
+
+static struct i2c_gpio_platform_data fsg_i2c_gpio_data = {
+ .sda_pin = FSG_SDA_PIN,
+ .scl_pin = FSG_SCL_PIN,
+};
+
+static struct platform_device fsg_i2c_gpio = {
+ .name = "i2c-gpio",
+ .id = 0,
+ .dev = {
+ .platform_data = &fsg_i2c_gpio_data,
+ },
+};
+
+static struct i2c_board_info __initdata fsg_i2c_board_info [] = {
+ {
+ I2C_BOARD_INFO("rtc-isl1208", 0x6f),
+ },
+};
+
+static struct resource fsg_uart_resources[] = {
+ {
+ .start = IXP4XX_UART1_BASE_PHYS,
+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IXP4XX_UART2_BASE_PHYS,
+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM,
+ }
+};
+
+static struct plat_serial8250_port fsg_uart_data[] = {
+ {
+ .mapbase = IXP4XX_UART1_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART1,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ {
+ .mapbase = IXP4XX_UART2_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART2,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ { }
+};
+
+static struct platform_device fsg_uart = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev = {
+ .platform_data = fsg_uart_data,
+ },
+ .num_resources = ARRAY_SIZE(fsg_uart_resources),
+ .resource = fsg_uart_resources,
+};
+
+static struct platform_device fsg_leds = {
+ .name = "fsg-led",
+ .id = -1,
+};
+
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info fsg_plat_eth[] = {
+ {
+ .phy = 5,
+ .rxq = 3,
+ .txreadyq = 20,
+ }, {
+ .phy = 4,
+ .rxq = 4,
+ .txreadyq = 21,
+ }
+};
+
+static struct platform_device fsg_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev = {
+ .platform_data = fsg_plat_eth,
+ },
+ }, {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEC,
+ .dev = {
+ .platform_data = fsg_plat_eth + 1,
+ },
+ }
+};
+
+static struct platform_device *fsg_devices[] __initdata = {
+ &fsg_i2c_gpio,
+ &fsg_flash,
+ &fsg_leds,
+ &fsg_eth[0],
+ &fsg_eth[1],
+};
+
+static irqreturn_t fsg_power_handler(int irq, void *dev_id)
+{
+ /* Signal init to do the ctrlaltdel action, this will bypass init if
+ * it hasn't started and do a kernel_restart.
+ */
+ ctrl_alt_del();
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t fsg_reset_handler(int irq, void *dev_id)
+{
+ /* This is the paper-clip reset which does an emergency reboot. */
+ printk(KERN_INFO "Restarting system.\n");
+ machine_restart(NULL);
+
+ /* This should never be reached. */
+ return IRQ_HANDLED;
+}
+
+static void __init fsg_init(void)
+{
+ DECLARE_MAC_BUF(mac_buf);
+ uint8_t __iomem *f;
+ int i;
+
+ ixp4xx_sys_init();
+
+ fsg_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+ fsg_flash_resource.end =
+ IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
+
+ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
+ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+
+ /* Configure CS2 for operation, 8bit and writable */
+ *IXP4XX_EXP_CS2 = 0xbfff0002;
+
+ i2c_register_board_info(0, fsg_i2c_board_info,
+ ARRAY_SIZE(fsg_i2c_board_info));
+
+ /* This is only useful on a modified machine, but it is valuable
+ * to have it first in order to see debug messages, and so that
+ * it does *not* get removed if platform_add_devices fails!
+ */
+ (void)platform_device_register(&fsg_uart);
+
+ platform_add_devices(fsg_devices, ARRAY_SIZE(fsg_devices));
+
+ if (request_irq(gpio_to_irq(FSG_RB_GPIO), &fsg_reset_handler,
+ IRQF_DISABLED | IRQF_TRIGGER_LOW,
+ "FSG reset button", NULL) < 0) {
+
+ printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
+ gpio_to_irq(FSG_RB_GPIO));
+ }
+
+ if (request_irq(gpio_to_irq(FSG_SB_GPIO), &fsg_power_handler,
+ IRQF_DISABLED | IRQF_TRIGGER_LOW,
+ "FSG power button", NULL) < 0) {
+
+ printk(KERN_DEBUG "Power Button IRQ %d not available\n",
+ gpio_to_irq(FSG_SB_GPIO));
+ }
+
+ /*
+ * Map in a portion of the flash and read the MAC addresses.
+ * Since it is stored in BE in the flash itself, we need to
+ * byteswap it if we're in LE mode.
+ */
+ f = ioremap(IXP4XX_EXP_BUS_BASE(0), 0x400000);
+ if (f) {
+#ifdef __ARMEB__
+ for (i = 0; i < 6; i++) {
+ fsg_plat_eth[0].hwaddr[i] = readb(f + 0x3C0422 + i);
+ fsg_plat_eth[1].hwaddr[i] = readb(f + 0x3C043B + i);
+ }
+#else
+
+ /*
+ Endian-swapped reads from unaligned addresses are
+ required to extract the two MACs from the big-endian
+ Redboot config area in flash.
+ */
+
+ fsg_plat_eth[0].hwaddr[0] = readb(f + 0x3C0421);
+ fsg_plat_eth[0].hwaddr[1] = readb(f + 0x3C0420);
+ fsg_plat_eth[0].hwaddr[2] = readb(f + 0x3C0427);
+ fsg_plat_eth[0].hwaddr[3] = readb(f + 0x3C0426);
+ fsg_plat_eth[0].hwaddr[4] = readb(f + 0x3C0425);
+ fsg_plat_eth[0].hwaddr[5] = readb(f + 0x3C0424);
+
+ fsg_plat_eth[1].hwaddr[0] = readb(f + 0x3C0439);
+ fsg_plat_eth[1].hwaddr[1] = readb(f + 0x3C043F);
+ fsg_plat_eth[1].hwaddr[2] = readb(f + 0x3C043E);
+ fsg_plat_eth[1].hwaddr[3] = readb(f + 0x3C043D);
+ fsg_plat_eth[1].hwaddr[4] = readb(f + 0x3C043C);
+ fsg_plat_eth[1].hwaddr[5] = readb(f + 0x3C0443);
+#endif
+ iounmap(f);
+ }
+ printk(KERN_INFO "FSG: Using MAC address %s for port 0\n",
+ print_mac(mac_buf, fsg_plat_eth[0].hwaddr));
+ printk(KERN_INFO "FSG: Using MAC address %s for port 1\n",
+ print_mac(mac_buf, fsg_plat_eth[1].hwaddr));
+
+}
+
+MACHINE_START(FSG, "Freecom FSG-3")
+ /* Maintainer: www.nslu2-linux.org */
+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ .map_io = ixp4xx_map_io,
+ .init_irq = ixp4xx_init_irq,
+ .timer = &ixp4xx_timer,
+ .boot_params = 0x0100,
+ .init_machine = fsg_init,
+MACHINE_END
+
--- /dev/null
+++ b/include/asm-arm/arch-ixp4xx/fsg.h
@@ -0,0 +1,50 @@
+/*
+ * include/asm-arm/arch-ixp4xx/fsg.h
+ *
+ * Freecom FSG-3 platform specific definitions
+ *
+ * Author: Rod Whitby <rod@whitby.id.au>
+ * Author: Tomasz Chmielewski <mangoo@wpkg.org>
+ * Maintainers: http://www.nslu2-linux.org
+ *
+ * Based on coyote.h by
+ * Copyright 2004 (c) MontaVista, Software, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __ASM_ARCH_HARDWARE_H__
+#error "Do not include this directly, instead #include <asm/hardware.h>"
+#endif
+
+#define FSG_SDA_PIN 12
+#define FSG_SCL_PIN 13
+
+/*
+ * FSG PCI IRQs
+ */
+#define FSG_PCI_MAX_DEV 3
+#define FSG_PCI_IRQ_LINES 3
+
+
+/* PCI controller GPIO to IRQ pin mappings */
+#define FSG_PCI_INTA_PIN 6
+#define FSG_PCI_INTB_PIN 7
+#define FSG_PCI_INTC_PIN 5
+
+/* Buttons */
+
+#define FSG_SB_GPIO 4 /* sync button */
+#define FSG_RB_GPIO 9 /* reset button */
+#define FSG_UB_GPIO 10 /* usb button */
+
+/* LEDs */
+
+#define FSG_LED_WLAN_BIT 0
+#define FSG_LED_WAN_BIT 1
+#define FSG_LED_SATA_BIT 2
+#define FSG_LED_USB_BIT 4
+#define FSG_LED_RING_BIT 5
+#define FSG_LED_SYNC_BIT 7
--- a/include/asm-arm/arch-ixp4xx/hardware.h
+++ b/include/asm-arm/arch-ixp4xx/hardware.h
@@ -45,5 +45,6 @@
#include "nslu2.h"
#include "nas100d.h"
#include "dsmg600.h"
+#include "fsg.h"
#endif /* _ASM_ARCH_HARDWARE_H */
--- a/include/asm-arm/arch-ixp4xx/irqs.h
+++ b/include/asm-arm/arch-ixp4xx/irqs.h
@@ -128,4 +128,11 @@
#define IRQ_DSMG600_PCI_INTE IRQ_IXP4XX_GPIO7
#define IRQ_DSMG600_PCI_INTF IRQ_IXP4XX_GPIO6
+/*
+ * Freecom FSG-3 Board IRQs
+ */
+#define IRQ_FSG_PCI_INTA IRQ_IXP4XX_GPIO6
+#define IRQ_FSG_PCI_INTB IRQ_IXP4XX_GPIO7
+#define IRQ_FSG_PCI_INTC IRQ_IXP4XX_GPIO5
+
#endif

View File

@ -0,0 +1,15 @@
--- a/drivers/char/random.c
+++ b/drivers/char/random.c
@@ -248,9 +248,9 @@
/*
* Configuration information
*/
-#define INPUT_POOL_WORDS 128
-#define OUTPUT_POOL_WORDS 32
-#define SEC_XFER_SIZE 512
+#define INPUT_POOL_WORDS 256
+#define OUTPUT_POOL_WORDS 64
+#define SEC_XFER_SIZE 1024
/*
* The minimum number of bits of entropy before we wake up a read on

View File

@ -0,0 +1,40 @@
--- a/arch/arm/mach-ixp4xx/gateway7001-setup.c
+++ b/arch/arm/mach-ixp4xx/gateway7001-setup.c
@@ -76,9 +76,36 @@
.resource = &gateway7001_uart_resource,
};
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info gateway7001_plat_eth[] = {
+ {
+ .phy = 1,
+ .rxq = 3,
+ .txreadyq = 20,
+ }, {
+ .phy = 2,
+ .rxq = 4,
+ .txreadyq = 21,
+ }
+};
+
+static struct platform_device gateway7001_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = gateway7001_plat_eth,
+ }, {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEC,
+ .dev.platform_data = gateway7001_plat_eth + 1,
+ }
+};
+
static struct platform_device *gateway7001_devices[] __initdata = {
&gateway7001_flash,
- &gateway7001_uart
+ &gateway7001_uart,
+ &gateway7001_eth[0],
+ &gateway7001_eth[1],
};
static void __init gateway7001_init(void)

View File

@ -0,0 +1,30 @@
--- a/arch/arm/mach-ixp4xx/wg302v2-setup.c
+++ b/arch/arm/mach-ixp4xx/wg302v2-setup.c
@@ -77,9 +77,27 @@
.resource = &wg302v2_uart_resource,
};
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info wg302_plat_eth[] = {
+ {
+ .phy = 8,
+ .rxq = 3,
+ .txreadyq = 20,
+ }
+};
+
+static struct platform_device wg302_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = wg302_plat_eth,
+ }
+};
+
static struct platform_device *wg302v2_devices[] __initdata = {
&wg302v2_flash,
&wg302v2_uart,
+ &wg302_eth[0],
};
static void __init wg302v2_init(void)

View File

@ -0,0 +1,286 @@
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -57,6 +57,14 @@
WG302 v2 or WAG302 v2 Access Points. For more information
on this platform, see http://openwrt.org
+config MACH_PRONGHORNMETRO
+ bool "Pronghorn Metro"
+ select PCI
+ help
+ Say 'Y' here if you want your kernel to support the ADI
+ Engineering Pronghorn Metro Platform. For more
+ information on this platform, see <file:Documentation/arm/IXP4xx>.
+
config ARCH_IXDP425
bool "IXDP425"
help
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
@@ -16,6 +16,7 @@
obj-pci-$(CONFIG_MACH_GATEWAY7001) += gateway7001-pci.o
obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o
obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o
+obj-pci-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-pci.o
obj-y += common.o
@@ -30,6 +31,7 @@
obj-$(CONFIG_MACH_GATEWAY7001) += gateway7001-setup.o
obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o
obj-$(CONFIG_MACH_FSG) += fsg-setup.o
+obj-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-setup.o
obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o
obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/pronghornmetro-pci.c
@@ -0,0 +1,74 @@
+/*
+ * arch/arch/mach-ixp4xx/pronghornmetro-pci.c
+ *
+ * PCI setup routines for ADI Engineering Pronghorn Metro
+ *
+ * Copyright (C) 2007 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * based on coyote-pci.c:
+ * Copyright (C) 2002 Jungo Software Technologies.
+ * Copyright (C) 2003 MontaVista Softwrae, Inc.
+ *
+ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+
+#include <asm/mach-types.h>
+#include <asm/hardware.h>
+#include <asm/irq.h>
+
+#include <asm/mach/pci.h>
+
+extern void ixp4xx_pci_preinit(void);
+extern int ixp4xx_setup(int nr, struct pci_sys_data *sys);
+extern struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys);
+
+void __init pronghornmetro_pci_preinit(void)
+{
+ set_irq_type(IRQ_IXP4XX_GPIO4, IRQT_LOW);
+ set_irq_type(IRQ_IXP4XX_GPIO6, IRQT_LOW);
+ set_irq_type(IRQ_IXP4XX_GPIO11, IRQT_LOW);
+ set_irq_type(IRQ_IXP4XX_GPIO1, IRQT_LOW);
+
+ ixp4xx_pci_preinit();
+}
+
+static int __init pronghornmetro_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+ if (slot == 13)
+ return IRQ_IXP4XX_GPIO4;
+ else if (slot == 14)
+ return IRQ_IXP4XX_GPIO6;
+ else if (slot == 15)
+ return IRQ_IXP4XX_GPIO11;
+ else if (slot == 16)
+ return IRQ_IXP4XX_GPIO1;
+ else return -1;
+}
+
+struct hw_pci pronghornmetro_pci __initdata = {
+ .nr_controllers = 1,
+ .preinit = pronghornmetro_pci_preinit,
+ .swizzle = pci_std_swizzle,
+ .setup = ixp4xx_setup,
+ .scan = ixp4xx_scan_bus,
+ .map_irq = pronghornmetro_map_irq,
+};
+
+int __init pronghornmetro_pci_init(void)
+{
+ if (machine_is_pronghorn_metro())
+ pci_common_init(&pronghornmetro_pci);
+ return 0;
+}
+
+subsys_initcall(pronghornmetro_pci_init);
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/pronghornmetro-setup.c
@@ -0,0 +1,147 @@
+/*
+ * arch/arm/mach-ixp4xx/pronghornmetro-setup.c
+ *
+ * Board setup for the ADI Engineering Pronghorn Metro
+ *
+ * Copyright (C) 2007 Imre Kaloz <Kaloz@openwrt.org>
+ *
+ * based on coyote-setup.c:
+ * Copyright (C) 2003-2005 MontaVista Software, Inc.
+ *
+ * Author: Imre Kaloz <Kaloz@openwrt.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/serial_8250.h>
+#include <linux/slab.h>
+
+#include <asm/types.h>
+#include <asm/setup.h>
+#include <asm/memory.h>
+#include <asm/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+static struct flash_platform_data pronghornmetro_flash_data = {
+ .map_name = "cfi_probe",
+ .width = 2,
+};
+
+static struct resource pronghornmetro_flash_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device pronghornmetro_flash = {
+ .name = "IXP4XX-Flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &pronghornmetro_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &pronghornmetro_flash_resource,
+};
+
+static struct resource pronghornmetro_uart_resource = {
+ .start = IXP4XX_UART2_BASE_PHYS,
+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct plat_serial8250_port pronghornmetro_uart_data[] = {
+ {
+ .mapbase = IXP4XX_UART2_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART2,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ { },
+};
+
+static struct platform_device pronghornmetro_uart = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev = {
+ .platform_data = pronghornmetro_uart_data,
+ },
+ .num_resources = 1,
+ .resource = &pronghornmetro_uart_resource,
+};
+
+static struct resource pronghornmetro_pata_resources[] = {
+ {
+ .flags = IORESOURCE_MEM
+ },
+ {
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .name = "intrq",
+ .start = IRQ_IXP4XX_GPIO0,
+ .end = IRQ_IXP4XX_GPIO0,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct ixp4xx_pata_data pronghornmetro_pata_data = {
+ .cs0_bits = 0xbfff0043,
+ .cs1_bits = 0xbfff0043,
+};
+
+static struct platform_device pronghornmetro_pata = {
+ .name = "pata_ixp4xx_cf",
+ .id = 0,
+ .dev.platform_data = &pronghornmetro_pata_data,
+ .num_resources = ARRAY_SIZE(pronghornmetro_pata_resources),
+ .resource = pronghornmetro_pata_resources,
+};
+
+static struct platform_device *pronghornmetro_devices[] __initdata = {
+ &pronghornmetro_flash,
+ &pronghornmetro_uart,
+};
+
+static void __init pronghornmetro_init(void)
+{
+ ixp4xx_sys_init();
+
+ pronghornmetro_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+ pronghornmetro_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_16M - 1;
+
+ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
+ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+
+ platform_add_devices(pronghornmetro_devices, ARRAY_SIZE(pronghornmetro_devices));
+
+ pronghornmetro_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(1);
+ pronghornmetro_pata_resources[0].end = IXP4XX_EXP_BUS_END(1);
+
+ pronghornmetro_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(2);
+ pronghornmetro_pata_resources[1].end = IXP4XX_EXP_BUS_END(2);
+
+ pronghornmetro_pata_data.cs0_cfg = IXP4XX_EXP_CS1;
+ pronghornmetro_pata_data.cs1_cfg = IXP4XX_EXP_CS2;
+
+ platform_device_register(&pronghornmetro_pata);
+}
+
+#ifdef CONFIG_MACH_PRONGHORNMETRO
+MACHINE_START(PRONGHORNMETRO, "ADI Engineering Pronghorn Metro")
+ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ .map_io = ixp4xx_map_io,
+ .init_irq = ixp4xx_init_irq,
+ .timer = &ixp4xx_timer,
+ .boot_params = 0x0100,
+ .init_machine = pronghornmetro_init,
+MACHINE_END
+#endif
--- a/Documentation/arm/IXP4xx
+++ b/Documentation/arm/IXP4xx
@@ -111,6 +111,9 @@
the platform has two mini-PCI slots used for 802.11[bga] cards.
Finally, there is an IDE port hanging off the expansion bus.
+ADI Engineering Pronghorn Metro Platform
+http://www.adiengineering.com/php-bin/ecomm4/productDisplay.php?category_id=30&product_id=85
+
Gateworks Avila Network Platform
http://www.gateworks.com/avila_sbc.htm
--- a/include/asm-arm/arch-ixp4xx/uncompress.h
+++ b/include/asm-arm/arch-ixp4xx/uncompress.h
@@ -41,7 +41,8 @@
* Some boards are using UART2 as console
*/
if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
- machine_is_gateway7001() || machine_is_wg302v2())
+ machine_is_gateway7001() || machine_is_wg302v2() ||
+ machine_is_pronghorn_metro())
uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
else
uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;

View File

@ -0,0 +1,39 @@
--- a/arch/arm/mach-ixp4xx/pronghornmetro-setup.c
+++ b/arch/arm/mach-ixp4xx/pronghornmetro-setup.c
@@ -104,9 +104,36 @@
.resource = pronghornmetro_pata_resources,
};
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info pronghornmetro_plat_eth[] = {
+ {
+ .phy = 0,
+ .rxq = 3,
+ .txreadyq = 20,
+ }, {
+ .phy = 1,
+ .rxq = 4,
+ .txreadyq = 21,
+ }
+};
+
+static struct platform_device pronghornmetro_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = pronghornmetro_plat_eth,
+ }, {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEC,
+ .dev.platform_data = pronghornmetro_plat_eth + 1,
+ }
+};
+
static struct platform_device *pronghornmetro_devices[] __initdata = {
&pronghornmetro_flash,
&pronghornmetro_uart,
+ &pronghornmetro_eth[0],
+ &pronghornmetro_eth[1],
};
static void __init pronghornmetro_init(void)

View File

@ -0,0 +1,180 @@
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -65,6 +65,14 @@
Engineering Pronghorn Metro Platform. For more
information on this platform, see <file:Documentation/arm/IXP4xx>.
+config MACH_COMPEX
+ bool "Compex WP18 / NP18A"
+ select PCI
+ help
+ Say 'Y' here if you want your kernel to support Compex'
+ WP18 or NP18A boards. For more information on this
+ platform, see http://openwrt.org
+
config ARCH_IXDP425
bool "IXDP425"
help
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
@@ -17,6 +17,7 @@
obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o
obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o
obj-pci-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-pci.o
+obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o
obj-y += common.o
@@ -32,6 +33,7 @@
obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o
obj-$(CONFIG_MACH_FSG) += fsg-setup.o
obj-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-setup.o
+obj-$(CONFIG_MACH_COMPEX) += compex-setup.o
obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o
obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/compex-setup.c
@@ -0,0 +1,120 @@
+/*
+ * arch/arm/mach-ixp4xx/compex-setup.c
+ *
+ * Ccompex WP18 / NP18A board-setup
+ *
+ * Copyright (C) 2007 Imre Kaloz <Kaloz@openwrt.org>
+ *
+ * based on ixdp425-setup.c:
+ * Copyright (C) 2003-2005 MontaVista Software, Inc.
+ *
+ * Author: Imre Kaloz <Kaloz@openwrt.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/serial_8250.h>
+#include <linux/slab.h>
+
+#include <asm/types.h>
+#include <asm/setup.h>
+#include <asm/memory.h>
+#include <asm/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+static struct flash_platform_data compex_flash_data = {
+ .map_name = "cfi_probe",
+ .width = 2,
+};
+
+static struct resource compex_flash_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device compex_flash = {
+ .name = "IXP4XX-Flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &compex_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &compex_flash_resource,
+};
+
+static struct resource compex_uart_resources[] = {
+ {
+ .start = IXP4XX_UART1_BASE_PHYS,
+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM
+ },
+ {
+ .start = IXP4XX_UART2_BASE_PHYS,
+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM
+ }
+};
+
+static struct plat_serial8250_port compex_uart_data[] = {
+ {
+ .mapbase = IXP4XX_UART1_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART1,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ {
+ .mapbase = IXP4XX_UART2_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART2,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ { },
+};
+
+static struct platform_device compex_uart = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev.platform_data = compex_uart_data,
+ .num_resources = 2,
+ .resource = compex_uart_resources,
+};
+
+static struct platform_device *compex_devices[] __initdata = {
+ &compex_flash,
+ &compex_uart
+};
+
+static void __init compex_init(void)
+{
+ ixp4xx_sys_init();
+
+ compex_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+ compex_flash_resource.end =
+ IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
+
+ platform_add_devices(compex_devices, ARRAY_SIZE(compex_devices));
+}
+
+#ifdef CONFIG_MACH_COMPEX
+MACHINE_START(COMPEX, "Compex WP18 / NP18A")
+ /* Maintainer: Imre Kaloz <Kaloz@openwrt.org> */
+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ .map_io = ixp4xx_map_io,
+ .init_irq = ixp4xx_init_irq,
+ .timer = &ixp4xx_timer,
+ .boot_params = 0x0100,
+ .init_machine = compex_init,
+MACHINE_END
+#endif
--- a/arch/arm/mach-ixp4xx/ixdp425-pci.c
+++ b/arch/arm/mach-ixp4xx/ixdp425-pci.c
@@ -66,7 +66,7 @@
int __init ixdp425_pci_init(void)
{
if (machine_is_ixdp425() || machine_is_ixcdp1100() ||
- machine_is_ixdp465() || machine_is_kixrp435())
+ machine_is_ixdp465() || machine_is_kixrp435() || machine_is_compex())
pci_common_init(&ixdp425_pci);
return 0;
}
--- a/arch/arm/tools/mach-types
+++ b/arch/arm/tools/mach-types
@@ -1276,7 +1276,7 @@
smdk6400 MACH_SMDK6400 SMDK6400 1270
nokia_n800 MACH_NOKIA_N800 NOKIA_N800 1271
greenphone MACH_GREENPHONE GREENPHONE 1272
-compex42x MACH_COMPEXWP18 COMPEXWP18 1273
+compex MACH_COMPEX COMPEX 1273
xmate MACH_XMATE XMATE 1274
energizer MACH_ENERGIZER ENERGIZER 1275
ime1 MACH_IME1 IME1 1276

View File

@ -0,0 +1,40 @@
--- a/arch/arm/mach-ixp4xx/compex-setup.c
+++ b/arch/arm/mach-ixp4xx/compex-setup.c
@@ -90,9 +90,36 @@
.resource = compex_uart_resources,
};
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info compex_plat_eth[] = {
+ {
+ .phy = -1,
+ .rxq = 3,
+ .txreadyq = 20,
+ }, {
+ .phy = 3,
+ .rxq = 4,
+ .txreadyq = 21,
+ }
+};
+
+static struct platform_device compex_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = compex_plat_eth,
+ }, {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEC,
+ .dev.platform_data = compex_plat_eth + 1,
+ }
+};
+
static struct platform_device *compex_devices[] __initdata = {
&compex_flash,
- &compex_uart
+ &compex_uart,
+ &compex_eth[0],
+ &compex_eth[1],
};
static void __init compex_init(void)

View File

@ -0,0 +1,225 @@
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -73,6 +73,14 @@
WP18 or NP18A boards. For more information on this
platform, see http://openwrt.org
+config MACH_WRT300NV2
+ bool "Linksys WRT300N v2"
+ select PCI
+ help
+ Say 'Y' here if you want your kernel to support Linksys'
+ WRT300N v2 router. For more information on this
+ platform, see http://openwrt.org
+
config ARCH_IXDP425
bool "IXDP425"
help
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
@@ -18,6 +18,7 @@
obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o
obj-pci-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-pci.o
obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o
+obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o
obj-y += common.o
@@ -34,6 +35,7 @@
obj-$(CONFIG_MACH_FSG) += fsg-setup.o
obj-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-setup.o
obj-$(CONFIG_MACH_COMPEX) += compex-setup.o
+obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o
obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o
obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/wrt300nv2-pci.c
@@ -0,0 +1,65 @@
+/*
+ * arch/arch/mach-ixp4xx/wrt300nv2-pci.c
+ *
+ * PCI setup routines for Linksys WRT300N v2
+ *
+ * Copyright (C) 2007 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * based on coyote-pci.c:
+ * Copyright (C) 2002 Jungo Software Technologies.
+ * Copyright (C) 2003 MontaVista Softwrae, Inc.
+ *
+ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+
+#include <asm/mach-types.h>
+#include <asm/hardware.h>
+#include <asm/irq.h>
+
+#include <asm/mach/pci.h>
+
+extern void ixp4xx_pci_preinit(void);
+extern int ixp4xx_setup(int nr, struct pci_sys_data *sys);
+extern struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys);
+
+void __init wrt300nv2_pci_preinit(void)
+{
+ set_irq_type(IRQ_IXP4XX_GPIO8, IRQT_LOW);
+
+ ixp4xx_pci_preinit();
+}
+
+static int __init wrt300nv2_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+ if (slot == 1)
+ return IRQ_IXP4XX_GPIO8;
+ else return -1;
+}
+
+struct hw_pci wrt300nv2_pci __initdata = {
+ .nr_controllers = 1,
+ .preinit = wrt300nv2_pci_preinit,
+ .swizzle = pci_std_swizzle,
+ .setup = ixp4xx_setup,
+ .scan = ixp4xx_scan_bus,
+ .map_irq = wrt300nv2_map_irq,
+};
+
+int __init wrt300nv2_pci_init(void)
+{
+ if (machine_is_wrt300nv2())
+ pci_common_init(&wrt300nv2_pci);
+ return 0;
+}
+
+subsys_initcall(wrt300nv2_pci_init);
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/wrt300nv2-setup.c
@@ -0,0 +1,108 @@
+/*
+ * arch/arm/mach-ixp4xx/wrt300nv2-setup.c
+ *
+ * Board setup for the Linksys WRT300N v2
+ *
+ * Copyright (C) 2007 Imre Kaloz <Kaloz@openwrt.org>
+ *
+ * based on coyote-setup.c:
+ * Copyright (C) 2003-2005 MontaVista Software, Inc.
+ *
+ * Author: Imre Kaloz <Kaloz@openwrt.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/serial_8250.h>
+#include <linux/slab.h>
+
+#include <asm/types.h>
+#include <asm/setup.h>
+#include <asm/memory.h>
+#include <asm/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+static struct flash_platform_data wrt300nv2_flash_data = {
+ .map_name = "cfi_probe",
+ .width = 2,
+};
+
+static struct resource wrt300nv2_flash_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device wrt300nv2_flash = {
+ .name = "IXP4XX-Flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &wrt300nv2_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &wrt300nv2_flash_resource,
+};
+
+static struct resource wrt300nv2_uart_resource = {
+ .start = IXP4XX_UART2_BASE_PHYS,
+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct plat_serial8250_port wrt300nv2_uart_data[] = {
+ {
+ .mapbase = IXP4XX_UART2_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART2,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ { },
+};
+
+static struct platform_device wrt300nv2_uart = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev = {
+ .platform_data = wrt300nv2_uart_data,
+ },
+ .num_resources = 1,
+ .resource = &wrt300nv2_uart_resource,
+};
+
+static struct platform_device *wrt300nv2_devices[] __initdata = {
+ &wrt300nv2_flash,
+ &wrt300nv2_uart
+};
+
+static void __init wrt300nv2_init(void)
+{
+ ixp4xx_sys_init();
+
+ wrt300nv2_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+ wrt300nv2_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
+
+ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
+ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+
+ platform_add_devices(wrt300nv2_devices, ARRAY_SIZE(wrt300nv2_devices));
+}
+
+#ifdef CONFIG_MACH_WRT300NV2
+MACHINE_START(WRT300NV2, "Linksys WRT300N v2")
+ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ .map_io = ixp4xx_map_io,
+ .init_irq = ixp4xx_init_irq,
+ .timer = &ixp4xx_timer,
+ .boot_params = 0x0100,
+ .init_machine = wrt300nv2_init,
+MACHINE_END
+#endif
--- a/include/asm-arm/arch-ixp4xx/uncompress.h
+++ b/include/asm-arm/arch-ixp4xx/uncompress.h
@@ -42,7 +42,7 @@
*/
if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
machine_is_gateway7001() || machine_is_wg302v2() ||
- machine_is_pronghorn_metro())
+ machine_is_pronghorn_metro() || machine_is_wrt300nv2())
uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
else
uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;

View File

@ -0,0 +1,40 @@
--- a/arch/arm/mach-ixp4xx/wrt300nv2-setup.c
+++ b/arch/arm/mach-ixp4xx/wrt300nv2-setup.c
@@ -76,9 +76,36 @@
.resource = &wrt300nv2_uart_resource,
};
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info wrt300nv2_plat_eth[] = {
+ {
+ .phy = -1,
+ .rxq = 3,
+ .txreadyq = 20,
+ }, {
+ .phy = 1,
+ .rxq = 4,
+ .txreadyq = 21,
+ }
+};
+
+static struct platform_device wrt300nv2_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = wrt300nv2_plat_eth,
+ }, {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEC,
+ .dev.platform_data = wrt300nv2_plat_eth + 1,
+ }
+};
+
static struct platform_device *wrt300nv2_devices[] __initdata = {
&wrt300nv2_flash,
- &wrt300nv2_uart
+ &wrt300nv2_uart,
+ &wrt300nv2_eth[0],
+ &wrt300nv2_eth[1],
};
static void __init wrt300nv2_init(void)

View File

@ -0,0 +1,236 @@
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -65,6 +65,14 @@
Engineering Pronghorn Metro Platform. For more
information on this platform, see <file:Documentation/arm/IXP4xx>.
+config MACH_SIDEWINDER
+ bool "Sidewinder"
+ select PCI
+ help
+ Say 'Y' here if you want your kernel to support the ADI
+ Engineering Sidewinder Platform. For more
+ information on this platform, see <file:Documentation/arm/IXP4xx>.
+
config MACH_COMPEX
bool "Compex WP18 / NP18A"
select PCI
@@ -163,7 +171,7 @@
#
config CPU_IXP46X
bool
- depends on MACH_IXDP465
+ depends on MACH_IXDP465 || MACH_SIDEWINDER
default y
config CPU_IXP43X
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
@@ -19,6 +19,7 @@
obj-pci-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-pci.o
obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o
obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o
+obj-pci-$(CONFIG_MACH_SIDEWINDER) += sidewinder-pci.o
obj-y += common.o
@@ -36,6 +37,7 @@
obj-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-setup.o
obj-$(CONFIG_MACH_COMPEX) += compex-setup.o
obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o
+obj-$(CONFIG_MACH_SIDEWINDER) += sidewinder-setup.o
obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o
obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/sidewinder-pci.c
@@ -0,0 +1,71 @@
+/*
+ * arch/arch/mach-ixp4xx/pronghornmetro-pci.c
+ *
+ * PCI setup routines for ADI Engineering Sidewinder
+ *
+ * Copyright (C) 2007 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * based on coyote-pci.c:
+ * Copyright (C) 2002 Jungo Software Technologies.
+ * Copyright (C) 2003 MontaVista Softwrae, Inc.
+ *
+ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+
+#include <asm/mach-types.h>
+#include <asm/hardware.h>
+#include <asm/irq.h>
+
+#include <asm/mach/pci.h>
+
+extern void ixp4xx_pci_preinit(void);
+extern int ixp4xx_setup(int nr, struct pci_sys_data *sys);
+extern struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys);
+
+void __init sidewinder_pci_preinit(void)
+{
+ set_irq_type(IRQ_IXP4XX_GPIO11, IRQT_LOW);
+ set_irq_type(IRQ_IXP4XX_GPIO10, IRQT_LOW);
+ set_irq_type(IRQ_IXP4XX_GPIO9, IRQT_LOW);
+
+ ixp4xx_pci_preinit();
+}
+
+static int __init sidewinder_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+ if (slot == 1)
+ return IRQ_IXP4XX_GPIO11;
+ else if (slot == 2)
+ return IRQ_IXP4XX_GPIO10;
+ else if (slot == 3)
+ return IRQ_IXP4XX_GPIO9;
+ else return -1;
+}
+
+struct hw_pci sidewinder_pci __initdata = {
+ .nr_controllers = 1,
+ .preinit = sidewinder_pci_preinit,
+ .swizzle = pci_std_swizzle,
+ .setup = ixp4xx_setup,
+ .scan = ixp4xx_scan_bus,
+ .map_irq = sidewinder_map_irq,
+};
+
+int __init sidewinder_pci_init(void)
+{
+ if (machine_is_sidewinder())
+ pci_common_init(&sidewinder_pci);
+ return 0;
+}
+
+subsys_initcall(sidewinder_pci_init);
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/sidewinder-setup.c
@@ -0,0 +1,115 @@
+/*
+ * arch/arm/mach-ixp4xx/sidewinder-setup.c
+ *
+ * Board setup for the ADI Engineering Sidewinder
+ *
+ * Copyright (C) 2007 Imre Kaloz <Kaloz@openwrt.org>
+ *
+ * based on coyote-setup.c:
+ * Copyright (C) 2003-2005 MontaVista Software, Inc.
+ *
+ * Author: Imre Kaloz <Kaloz@openwrt.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/serial.h>
+#include <linux/serial_8250.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+static struct flash_platform_data sidewinder_flash_data = {
+ .map_name = "cfi_probe",
+ .width = 2,
+};
+
+static struct resource sidewinder_flash_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device sidewinder_flash = {
+ .name = "IXP4XX-Flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &sidewinder_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &sidewinder_flash_resource,
+};
+
+static struct resource sidewinder_uart_resources[] = {
+ {
+ .start = IXP4XX_UART1_BASE_PHYS,
+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IXP4XX_UART2_BASE_PHYS,
+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM,
+ }
+};
+
+static struct plat_serial8250_port sidewinder_uart_data[] = {
+ {
+ .mapbase = IXP4XX_UART1_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART1,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ {
+ .mapbase = IXP4XX_UART2_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART2,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ { },
+};
+
+static struct platform_device sidewinder_uart = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev = {
+ .platform_data = sidewinder_uart_data,
+ },
+ .num_resources = ARRAY_SIZE(sidewinder_uart_resources),
+ .resource = sidewinder_uart_resources,
+};
+
+static struct platform_device *sidewinder_devices[] __initdata = {
+ &sidewinder_flash,
+ &sidewinder_uart,
+};
+
+static void __init sidewinder_init(void)
+{
+ ixp4xx_sys_init();
+
+ sidewinder_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+ sidewinder_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_64M - 1;
+
+ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
+ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+
+ platform_add_devices(sidewinder_devices, ARRAY_SIZE(sidewinder_devices));
+}
+
+#ifdef CONFIG_MACH_SIDEWINDER
+MACHINE_START(SIDEWINDER, "ADI Engineering Sidewinder")
+ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ .map_io = ixp4xx_map_io,
+ .init_irq = ixp4xx_init_irq,
+ .timer = &ixp4xx_timer,
+ .boot_params = 0x0100,
+ .init_machine = sidewinder_init,
+MACHINE_END
+#endif

View File

@ -0,0 +1,201 @@
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/ap1000-setup.c
@@ -0,0 +1,151 @@
+/*
+ * arch/arm/mach-ixp4xx/ap1000-setup.c
+ *
+ * Lanready AP-1000
+ *
+ * Copyright (C) 2007 Imre Kaloz <Kaloz@openwrt.org>
+ *
+ * based on ixdp425-setup.c:
+ * Copyright (C) 2003-2005 MontaVista Software, Inc.
+ *
+ * Author: Imre Kaloz <Kaloz@openwrt.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/serial_8250.h>
+#include <linux/slab.h>
+
+#include <asm/types.h>
+#include <asm/setup.h>
+#include <asm/memory.h>
+#include <asm/hardware.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+static struct flash_platform_data ap1000_flash_data = {
+ .map_name = "cfi_probe",
+ .width = 2,
+};
+
+static struct resource ap1000_flash_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device ap1000_flash = {
+ .name = "IXP4XX-Flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &ap1000_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &ap1000_flash_resource,
+};
+
+static struct resource ap1000_uart_resources[] = {
+ {
+ .start = IXP4XX_UART1_BASE_PHYS,
+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM
+ },
+ {
+ .start = IXP4XX_UART2_BASE_PHYS,
+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM
+ }
+};
+
+static struct plat_serial8250_port ap1000_uart_data[] = {
+ {
+ .mapbase = IXP4XX_UART1_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART1,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ {
+ .mapbase = IXP4XX_UART2_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART2,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ { },
+};
+
+static struct platform_device ap1000_uart = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev.platform_data = ap1000_uart_data,
+ .num_resources = 2,
+ .resource = ap1000_uart_resources
+};
+
+static struct platform_device *ap1000_devices[] __initdata = {
+ &ap1000_flash,
+ &ap1000_uart
+};
+
+static char ap1000_mem_fixup[] __initdata = "mem=64M ";
+
+static void __init ap1000_fixup(struct machine_desc *desc,
+ struct tag *tags, char **cmdline, struct meminfo *mi)
+
+{
+ struct tag *t = tags;
+ char *p = *cmdline;
+
+ /* Find the end of the tags table, taking note of any cmdline tag. */
+ for (; t->hdr.size; t = tag_next(t)) {
+ if (t->hdr.tag == ATAG_CMDLINE) {
+ p = t->u.cmdline.cmdline;
+ }
+ }
+
+ /* Overwrite the end of the table with a new cmdline tag. */
+ t->hdr.tag = ATAG_CMDLINE;
+ t->hdr.size = (sizeof (struct tag_header) +
+ strlen(ap1000_mem_fixup) + strlen(p) + 1 + 4) >> 2;
+ strlcpy(t->u.cmdline.cmdline, ap1000_mem_fixup, COMMAND_LINE_SIZE);
+ strlcpy(t->u.cmdline.cmdline + strlen(ap1000_mem_fixup), p,
+ COMMAND_LINE_SIZE - strlen(ap1000_mem_fixup));
+
+ /* Terminate the table. */
+ t = tag_next(t);
+ t->hdr.tag = ATAG_NONE;
+ t->hdr.size = 0;
+}
+
+static void __init ap1000_init(void)
+{
+ ixp4xx_sys_init();
+
+ ap1000_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+ ap1000_flash_resource.end =
+ IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
+
+ platform_add_devices(ap1000_devices, ARRAY_SIZE(ap1000_devices));
+}
+
+#ifdef CONFIG_MACH_AP1000
+MACHINE_START(AP1000, "Lanready AP-1000")
+ /* Maintainer: Imre Kaloz <Kaloz@openwrt.org> */
+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ .fixup = ap1000_fixup,
+ .map_io = ixp4xx_map_io,
+ .init_irq = ixp4xx_init_irq,
+ .timer = &ixp4xx_timer,
+ .boot_params = 0x0100,
+ .init_machine = ap1000_init,
+MACHINE_END
+#endif
--- a/arch/arm/mach-ixp4xx/ixdp425-pci.c
+++ b/arch/arm/mach-ixp4xx/ixdp425-pci.c
@@ -66,7 +66,8 @@
int __init ixdp425_pci_init(void)
{
if (machine_is_ixdp425() || machine_is_ixcdp1100() ||
- machine_is_ixdp465() || machine_is_kixrp435() || machine_is_compex())
+ machine_is_ixdp465() || machine_is_kixrp435() ||
+ machine_is_compex() || machine_is_ap1000())
pci_common_init(&ixdp425_pci);
return 0;
}
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -89,6 +89,14 @@
WRT300N v2 router. For more information on this
platform, see http://openwrt.org
+config MACH_AP1000
+ bool "Lanready AP-1000"
+ select PCI
+ help
+ Say 'Y' here if you want your kernel to support Lanready's
+ AP1000 board. For more information on this
+ platform, see http://openwrt.org
+
config ARCH_IXDP425
bool "IXDP425"
help
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
@@ -20,6 +20,7 @@
obj-pci-$(CONFIG_MACH_COMPEX) += ixdp425-pci.o
obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o
obj-pci-$(CONFIG_MACH_SIDEWINDER) += sidewinder-pci.o
+obj-pci-$(CONFIG_MACH_AP1000) += ixdp425-pci.o
obj-y += common.o
@@ -38,6 +39,7 @@
obj-$(CONFIG_MACH_COMPEX) += compex-setup.o
obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o
obj-$(CONFIG_MACH_SIDEWINDER) += sidewinder-setup.o
+obj-$(CONFIG_MACH_AP1000) += ap1000-setup.o
obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o
obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o

View File

@ -0,0 +1,41 @@
--- a/arch/arm/mach-ixp4xx/ap1000-setup.c
+++ b/arch/arm/mach-ixp4xx/ap1000-setup.c
@@ -90,9 +90,37 @@
.resource = ap1000_uart_resources
};
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info ap1000_plat_eth[] = {
+ {
+ .phy = IXP4XX_ETH_PHY_MAX_ADDR,
+ .phy_mask = 0x1e,
+ .rxq = 3,
+ .txreadyq = 20,
+ }, {
+ .phy = 5,
+ .rxq = 4,
+ .txreadyq = 21,
+ }
+};
+
+static struct platform_device ap1000_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = ap1000_plat_eth,
+ }, {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEC,
+ .dev.platform_data = ap1000_plat_eth + 1,
+ }
+};
+
static struct platform_device *ap1000_devices[] __initdata = {
&ap1000_flash,
- &ap1000_uart
+ &ap1000_uart,
+ &ap1000_eth[0],
+ &ap1000_eth[1],
};
static char ap1000_mem_fixup[] __initdata = "mem=64M ";

View File

@ -0,0 +1,213 @@
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -49,6 +49,14 @@
7001 Access Point. For more information on this platform,
see http://openwrt.org
+config MACH_WG302V1
+ bool "Netgear WG302 v1 / WAG302 v1"
+ select PCI
+ help
+ Say 'Y' here if you want your kernel to support Netgear's
+ WG302 v1 or WAG302 v1 Access Points. For more information
+ on this platform, see http://openwrt.org
+
config MACH_WG302V2
bool "Netgear WG302 v2 / WAG302 v2"
select PCI
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
@@ -14,6 +14,7 @@
obj-pci-$(CONFIG_MACH_NAS100D) += nas100d-pci.o
obj-pci-$(CONFIG_MACH_DSMG600) += dsmg600-pci.o
obj-pci-$(CONFIG_MACH_GATEWAY7001) += gateway7001-pci.o
+obj-pci-$(CONFIG_MACH_WG302V1) += wg302v1-pci.o
obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o
obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o
obj-pci-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-pci.o
@@ -33,6 +34,7 @@
obj-$(CONFIG_MACH_NAS100D) += nas100d-setup.o
obj-$(CONFIG_MACH_DSMG600) += dsmg600-setup.o
obj-$(CONFIG_MACH_GATEWAY7001) += gateway7001-setup.o
+obj-$(CONFIG_MACH_WG302V1) += wg302v1-setup.o
obj-$(CONFIG_MACH_WG302V2) += wg302v2-setup.o
obj-$(CONFIG_MACH_FSG) += fsg-setup.o
obj-$(CONFIG_MACH_PRONGHORNMETRO) += pronghornmetro-setup.o
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/wg302v1-pci.c
@@ -0,0 +1,63 @@
+/*
+ * arch/arch/mach-ixp4xx/wg302v1-pci.c
+ *
+ * PCI setup routines for the Netgear WG302 v1 and WAG302 v1
+ *
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * based on coyote-pci.c:
+ * Copyright (C) 2002 Jungo Software Technologies.
+ * Copyright (C) 2003 MontaVista Software, Inc.
+ *
+ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+
+#include <asm/mach-types.h>
+#include <asm/hardware.h>
+
+#include <asm/mach/pci.h>
+
+void __init wg302v1_pci_preinit(void)
+{
+ set_irq_type(IRQ_IXP4XX_GPIO8, IRQT_LOW);
+ set_irq_type(IRQ_IXP4XX_GPIO10, IRQT_LOW);
+
+ ixp4xx_pci_preinit();
+}
+
+static int __init wg302v1_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+ if (slot == 1)
+ return IRQ_IXP4XX_GPIO8;
+ else if (slot == 2)
+ return IRQ_IXP4XX_GPIO10;
+ else return -1;
+}
+
+struct hw_pci wg302v1_pci __initdata = {
+ .nr_controllers = 1,
+ .preinit = wg302v1_pci_preinit,
+ .swizzle = pci_std_swizzle,
+ .setup = ixp4xx_setup,
+ .scan = ixp4xx_scan_bus,
+ .map_irq = wg302v1_map_irq,
+};
+
+int __init wg302v1_pci_init(void)
+{
+ if (machine_is_wg302v1())
+ pci_common_init(&wg302v1_pci);
+ return 0;
+}
+
+subsys_initcall(wg302v1_pci_init);
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/wg302v1-setup.c
@@ -0,0 +1,109 @@
+/*
+ * arch/arm/mach-ixp4xx/wg302v1-setup.c
+ *
+ * Board setup for the Netgear WG302 v1 and WAG302 v1
+ *
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * based on coyote-setup.c:
+ * Copyright (C) 2003-2005 MontaVista Software, Inc.
+ *
+ * Author: Imre Kaloz <kaloz@openwrt.org>
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/serial_8250.h>
+#include <linux/slab.h>
+
+#include <asm/types.h>
+#include <asm/setup.h>
+#include <asm/memory.h>
+#include <asm/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+static struct flash_platform_data wg302v1_flash_data = {
+ .map_name = "cfi_probe",
+ .width = 2,
+};
+
+static struct resource wg302v1_flash_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device wg302v1_flash = {
+ .name = "IXP4XX-Flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &wg302v1_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &wg302v1_flash_resource,
+};
+
+static struct resource wg302v1_uart_resource = {
+ .start = IXP4XX_UART1_BASE_PHYS,
+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct plat_serial8250_port wg302v1_uart_data[] = {
+ {
+ .mapbase = IXP4XX_UART1_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART1,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ { },
+};
+
+static struct platform_device wg302v1_uart = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev = {
+ .platform_data = wg302v1_uart_data,
+ },
+ .num_resources = 1,
+ .resource = &wg302v1_uart_resource,
+};
+
+static struct platform_device *wg302v1_devices[] __initdata = {
+ &wg302v1_flash,
+ &wg302v1_uart,
+};
+
+static void __init wg302v1_init(void)
+{
+ ixp4xx_sys_init();
+
+ wg302v1_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+ wg302v1_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
+
+ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
+ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+
+ platform_add_devices(wg302v1_devices, ARRAY_SIZE(wg302v1_devices));
+}
+
+#ifdef CONFIG_MACH_WG302V1
+MACHINE_START(WG302V1, "Netgear WG302 v1 / WAG302 v1")
+ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ .map_io = ixp4xx_map_io,
+ .init_irq = ixp4xx_init_irq,
+ .timer = &ixp4xx_timer,
+ .boot_params = 0x0100,
+ .init_machine = wg302v1_init,
+MACHINE_END
+#endif

View File

@ -0,0 +1,30 @@
--- a/arch/arm/mach-ixp4xx/wg302v1-setup.c
+++ b/arch/arm/mach-ixp4xx/wg302v1-setup.c
@@ -77,9 +77,27 @@
.resource = &wg302v1_uart_resource,
};
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info wg302_plat_eth[] = {
+ {
+ .phy = 30,
+ .rxq = 3,
+ .txreadyq = 20,
+ }
+};
+
+static struct platform_device wg302_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = wg302_plat_eth,
+ }
+};
+
static struct platform_device *wg302v1_devices[] __initdata = {
&wg302v1_flash,
&wg302v1_uart,
+ &wg302_eth[0],
};
static void __init wg302v1_init(void)

View File

@ -0,0 +1,47 @@
--- a/arch/arm/mach-ixp4xx/wg302v1-setup.c
+++ b/arch/arm/mach-ixp4xx/wg302v1-setup.c
@@ -100,6 +100,36 @@
&wg302_eth[0],
};
+static char wg302v1_mem_fixup[] __initdata = "mem=32M ";
+
+static void __init wg302v1_fixup(struct machine_desc *desc,
+ struct tag *tags, char **cmdline, struct meminfo *mi)
+
+{
+ struct tag *t = tags;
+ char *p = *cmdline;
+
+ /* Find the end of the tags table, taking note of any cmdline tag. */
+ for (; t->hdr.size; t = tag_next(t)) {
+ if (t->hdr.tag == ATAG_CMDLINE) {
+ p = t->u.cmdline.cmdline;
+ }
+ }
+
+ /* Overwrite the end of the table with a new cmdline tag. */
+ t->hdr.tag = ATAG_CMDLINE;
+ t->hdr.size = (sizeof (struct tag_header) +
+ strlen(wg302v1_mem_fixup) + strlen(p) + 1 + 4) >> 2;
+ strlcpy(t->u.cmdline.cmdline, wg302v1_mem_fixup, COMMAND_LINE_SIZE);
+ strlcpy(t->u.cmdline.cmdline + strlen(wg302v1_mem_fixup), p,
+ COMMAND_LINE_SIZE - strlen(wg302v1_mem_fixup));
+
+ /* Terminate the table. */
+ t = tag_next(t);
+ t->hdr.tag = ATAG_NONE;
+ t->hdr.size = 0;
+}
+
static void __init wg302v1_init(void)
{
ixp4xx_sys_init();
@@ -118,6 +148,7 @@
/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
.phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
.io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ .fixup = wg302v1_fixup,
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &ixp4xx_timer,

View File

@ -0,0 +1,41 @@
--- a/arch/arm/mach-ixp4xx/coyote-setup.c
+++ b/arch/arm/mach-ixp4xx/coyote-setup.c
@@ -73,9 +73,37 @@
.resource = &coyote_uart_resource,
};
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info ixdpg425_plat_eth[] = {
+ {
+ .phy = 5,
+ .rxq = 3,
+ .txreadyq = 20,
+ }, {
+ .phy = 4,
+ .rxq = 4,
+ .txreadyq = 21,
+ }
+};
+
+static struct platform_device ixdpg425_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = ixdpg425_plat_eth,
+ }, {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEC,
+ .dev.platform_data = ixdpg425_plat_eth + 1,
+ }
+};
+
+
static struct platform_device *coyote_devices[] __initdata = {
&coyote_flash,
- &coyote_uart
+ &coyote_uart,
+ &ixdpg425_eth[0],
+ &ixdpg425_eth[1],
};
static void __init coyote_init(void)

View File

@ -0,0 +1,284 @@
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -150,6 +150,14 @@
PrPCM1100 Processor Mezanine Module. For more information on
this platform, see <file:Documentation/arm/IXP4xx>.
+config MACH_TW5334
+ bool "Titan Wireless TW-533-4"
+ select PCI
+ help
+ Say 'Y' here if you want your kernel to support the Titan
+ Wireless TW533-4. For more information on this platform,
+ see http://openwrt.org
+
config MACH_NAS100D
bool
prompt "NAS100D"
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
@@ -22,6 +22,7 @@
obj-pci-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-pci.o
obj-pci-$(CONFIG_MACH_SIDEWINDER) += sidewinder-pci.o
obj-pci-$(CONFIG_MACH_AP1000) += ixdp425-pci.o
+obj-pci-$(CONFIG_MACH_TW5334) += tw5334-pci.o
obj-y += common.o
@@ -42,6 +43,7 @@
obj-$(CONFIG_MACH_WRT300NV2) += wrt300nv2-setup.o
obj-$(CONFIG_MACH_SIDEWINDER) += sidewinder-setup.o
obj-$(CONFIG_MACH_AP1000) += ap1000-setup.o
+obj-$(CONFIG_MACH_TW5334) += tw5334-setup.o
obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o
obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/tw5334-setup.c
@@ -0,0 +1,162 @@
+/*
+ * arch/arm/mach-ixp4xx/tw5334-setup.c
+ *
+ * Board setup for the Titan Wireless TW-533-4
+ *
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * based on coyote-setup.c:
+ * Copyright (C) 2003-2005 MontaVista Software, Inc.
+ *
+ * Author: Imre Kaloz <Kaloz@openwrt.org>
+ */
+
+#include <linux/if_ether.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/serial_8250.h>
+#include <linux/slab.h>
+
+#include <asm/types.h>
+#include <asm/setup.h>
+#include <asm/memory.h>
+#include <asm/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+static struct flash_platform_data tw5334_flash_data = {
+ .map_name = "cfi_probe",
+ .width = 2,
+};
+
+static struct resource tw5334_flash_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device tw5334_flash = {
+ .name = "IXP4XX-Flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &tw5334_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &tw5334_flash_resource,
+};
+
+static struct resource tw5334_uart_resource = {
+ .start = IXP4XX_UART2_BASE_PHYS,
+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct plat_serial8250_port tw5334_uart_data[] = {
+ {
+ .mapbase = IXP4XX_UART2_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART2,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ { },
+};
+
+static struct platform_device tw5334_uart = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev = {
+ .platform_data = tw5334_uart_data,
+ },
+ .num_resources = 1,
+ .resource = &tw5334_uart_resource,
+};
+
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info tw5334_plat_eth[] = {
+ {
+ .phy = 0,
+ .rxq = 3,
+ .txreadyq = 20,
+ }, {
+ .phy = 1,
+ .rxq = 4,
+ .txreadyq = 21,
+ }
+};
+
+static struct platform_device tw5334_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = tw5334_plat_eth,
+ }, {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEC,
+ .dev.platform_data = tw5334_plat_eth + 1,
+ }
+};
+
+static struct platform_device *tw5334_devices[] __initdata = {
+ &tw5334_flash,
+ &tw5334_uart,
+ &tw5334_eth[0],
+ &tw5334_eth[1],
+};
+
+static void __init tw5334_init(void)
+{
+ DECLARE_MAC_BUF(mac_buf);
+ uint8_t __iomem *f;
+ int i;
+
+ ixp4xx_sys_init();
+
+ tw5334_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+ tw5334_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
+
+ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
+ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+
+ platform_add_devices(tw5334_devices, ARRAY_SIZE(tw5334_devices));
+
+ /*
+ * Map in a portion of the flash and read the MAC addresses.
+ * Since it is stored in BE in the flash itself, we need to
+ * byteswap it if we're in LE mode.
+ */
+ f = ioremap(IXP4XX_EXP_BUS_BASE(0), 0x1000000);
+ if (f) {
+ for (i = 0; i < 6; i++)
+#ifdef __ARMEB__
+ tw5334_plat_eth[0].hwaddr[i] = readb(f + 0xFC0422 + i);
+ tw5334_plat_eth[1].hwaddr[i] = readb(f + 0xFC043B + i);
+#else
+ tw5334_plat_eth[0].hwaddr[i] = readb(f + 0xFC0422 + (i^3));
+ tw5334_plat_eth[1].hwaddr[i] = readb(f + 0xFC043B + (i^3));
+#endif
+ iounmap(f);
+ }
+ printk(KERN_INFO "TW-533-4: Using MAC address %s for port 0\n",
+ print_mac(mac_buf, tw5334_plat_eth[0].hwaddr));
+ printk(KERN_INFO "TW-533-4: Using MAC address %s for port 1\n",
+ print_mac(mac_buf, tw5334_plat_eth[1].hwaddr));
+}
+
+#ifdef CONFIG_MACH_TW5334
+MACHINE_START(TW5334, "Titan Wireless TW-533-4")
+ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ .map_io = ixp4xx_map_io,
+ .init_irq = ixp4xx_init_irq,
+ .timer = &ixp4xx_timer,
+ .boot_params = 0x0100,
+ .init_machine = tw5334_init,
+MACHINE_END
+#endif
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/tw5334-pci.c
@@ -0,0 +1,69 @@
+/*
+ * arch/arch/mach-ixp4xx/tw5334-pci.c
+ *
+ * PCI setup routines for the Titan Wireless TW-533-4
+ *
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * based on coyote-pci.c:
+ * Copyright (C) 2002 Jungo Software Technologies.
+ * Copyright (C) 2003 MontaVista Softwrae, Inc.
+ *
+ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+
+#include <asm/mach-types.h>
+#include <asm/hardware.h>
+
+#include <asm/mach/pci.h>
+
+void __init tw5334_pci_preinit(void)
+{
+ set_irq_type(IRQ_IXP4XX_GPIO6, IRQT_LOW);
+ set_irq_type(IRQ_IXP4XX_GPIO2, IRQT_LOW);
+ set_irq_type(IRQ_IXP4XX_GPIO1, IRQT_LOW);
+ set_irq_type(IRQ_IXP4XX_GPIO0, IRQT_LOW);
+
+ ixp4xx_pci_preinit();
+}
+
+static int __init tw5334_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+ if (slot == 12)
+ return IRQ_IXP4XX_GPIO6;
+ else if (slot == 13)
+ return IRQ_IXP4XX_GPIO2;
+ else if (slot == 14)
+ return IRQ_IXP4XX_GPIO1;
+ else if (slot == 15)
+ return IRQ_IXP4XX_GPIO0;
+ else return -1;
+}
+
+struct hw_pci tw5334_pci __initdata = {
+ .nr_controllers = 1,
+ .preinit = tw5334_pci_preinit,
+ .swizzle = pci_std_swizzle,
+ .setup = ixp4xx_setup,
+ .scan = ixp4xx_scan_bus,
+ .map_irq = tw5334_map_irq,
+};
+
+int __init tw5334_pci_init(void)
+{
+ if (machine_is_tw5334())
+ pci_common_init(&tw5334_pci);
+ return 0;
+}
+
+subsys_initcall(tw5334_pci_init);
--- a/include/asm-arm/arch-ixp4xx/uncompress.h
+++ b/include/asm-arm/arch-ixp4xx/uncompress.h
@@ -42,7 +42,8 @@
*/
if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
machine_is_gateway7001() || machine_is_wg302v2() ||
- machine_is_pronghorn_metro() || machine_is_wrt300nv2())
+ machine_is_pronghorn_metro() || machine_is_wrt300nv2() ||
+ machine_is_tw5334())
uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
else
uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;

View File

@ -0,0 +1,579 @@
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -25,6 +25,14 @@
Avila Network Platform. For more information on this platform,
see <file:Documentation/arm/IXP4xx>.
+config MACH_CAMBRIA
+ bool "Cambria"
+ select PCI
+ help
+ Say 'Y' here if you want your kernel to support the Gateworks
+ Cambria series. For more information on this platform,
+ see <file:Documentation/arm/IXP4xx>.
+
config MACH_LOFT
bool "Loft"
depends on MACH_AVILA
@@ -200,7 +208,7 @@
config CPU_IXP43X
bool
- depends on MACH_KIXRP435
+ depends on MACH_KIXRP435 || MACH_CAMBRIA
default y
config MACH_GTWX5715
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
@@ -7,6 +7,7 @@
obj-pci-$(CONFIG_ARCH_IXDP4XX) += ixdp425-pci.o
obj-pci-$(CONFIG_MACH_AVILA) += avila-pci.o
+obj-pci-$(CONFIG_MACH_CAMBRIA) += cambria-pci.o
obj-pci-$(CONFIG_MACH_IXDPG425) += ixdpg425-pci.o
obj-pci-$(CONFIG_ARCH_ADI_COYOTE) += coyote-pci.o
obj-pci-$(CONFIG_MACH_GTWX5715) += gtwx5715-pci.o
@@ -28,6 +29,7 @@
obj-$(CONFIG_ARCH_IXDP4XX) += ixdp425-setup.o
obj-$(CONFIG_MACH_AVILA) += avila-setup.o
+obj-$(CONFIG_MACH_CAMBRIA) += cambria-setup.o
obj-$(CONFIG_MACH_IXDPG425) += coyote-setup.o
obj-$(CONFIG_ARCH_ADI_COYOTE) += coyote-setup.o
obj-$(CONFIG_MACH_GTWX5715) += gtwx5715-setup.o
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/cambria-pci.c
@@ -0,0 +1,74 @@
+/*
+ * arch/arch/mach-ixp4xx/cambria-pci.c
+ *
+ * PCI setup routines for Gateworks Cambria series
+ *
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * based on coyote-pci.c:
+ * Copyright (C) 2002 Jungo Software Technologies.
+ * Copyright (C) 2003 MontaVista Softwrae, Inc.
+ *
+ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+
+#include <asm/mach-types.h>
+#include <asm/hardware.h>
+#include <asm/irq.h>
+
+#include <asm/mach/pci.h>
+
+extern void ixp4xx_pci_preinit(void);
+extern int ixp4xx_setup(int nr, struct pci_sys_data *sys);
+extern struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys);
+
+void __init cambria_pci_preinit(void)
+{
+ set_irq_type(IRQ_IXP4XX_GPIO11, IRQT_LOW);
+ set_irq_type(IRQ_IXP4XX_GPIO10, IRQT_LOW);
+ set_irq_type(IRQ_IXP4XX_GPIO9, IRQT_LOW);
+ set_irq_type(IRQ_IXP4XX_GPIO8, IRQT_LOW);
+
+ ixp4xx_pci_preinit();
+}
+
+static int __init cambria_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+ if (slot == 1)
+ return IRQ_IXP4XX_GPIO11;
+ else if (slot == 2)
+ return IRQ_IXP4XX_GPIO10;
+ else if (slot == 3)
+ return IRQ_IXP4XX_GPIO9;
+ else if (slot == 4)
+ return IRQ_IXP4XX_GPIO8;
+ else return -1;
+}
+
+struct hw_pci cambria_pci __initdata = {
+ .nr_controllers = 1,
+ .preinit = cambria_pci_preinit,
+ .swizzle = pci_std_swizzle,
+ .setup = ixp4xx_setup,
+ .scan = ixp4xx_scan_bus,
+ .map_irq = cambria_map_irq,
+};
+
+int __init cambria_pci_init(void)
+{
+ if (machine_is_cambria())
+ pci_common_init(&cambria_pci);
+ return 0;
+}
+
+subsys_initcall(cambria_pci_init);
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/cambria-setup.c
@@ -0,0 +1,444 @@
+/*
+ * arch/arm/mach-ixp4xx/cambria-setup.c
+ *
+ * Board setup for the Gateworks Cambria series
+ *
+ * Copyright (C) 2008 Imre Kaloz <Kaloz@openwrt.org>
+ *
+ * based on coyote-setup.c:
+ * Copyright (C) 2003-2005 MontaVista Software, Inc.
+ *
+ * Author: Imre Kaloz <Kaloz@openwrt.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/if_ether.h>
+#include <linux/socket.h>
+#include <linux/netdevice.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/serial_8250.h>
+#include <linux/slab.h>
+#ifdef CONFIG_SENSORS_EEPROM
+# include <linux/i2c.h>
+# include <linux/eeprom.h>
+#endif
+
+#include <linux/leds.h>
+#include <linux/i2c-gpio.h>
+#include <asm/types.h>
+#include <asm/setup.h>
+#include <asm/memory.h>
+#include <asm/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+struct cambria_board_info {
+ unsigned char *model;
+ void (* setup)(void);
+};
+
+static struct cambria_board_info *cambria_info __initdata;
+
+static struct flash_platform_data cambria_flash_data = {
+ .map_name = "cfi_probe",
+ .width = 2,
+};
+
+static struct resource cambria_flash_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device cambria_flash = {
+ .name = "IXP4XX-Flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &cambria_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &cambria_flash_resource,
+};
+
+static struct i2c_gpio_platform_data cambria_i2c_gpio_data = {
+ .sda_pin = 7,
+ .scl_pin = 6,
+};
+
+static struct platform_device cambria_i2c_gpio = {
+ .name = "i2c-gpio",
+ .id = 0,
+ .dev = {
+ .platform_data = &cambria_i2c_gpio_data,
+ },
+};
+
+static struct resource cambria_uart_resource = {
+ .start = IXP4XX_UART1_BASE_PHYS,
+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct plat_serial8250_port cambria_uart_data[] = {
+ {
+ .mapbase = IXP4XX_UART1_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART1,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ { },
+};
+
+static struct platform_device cambria_uart = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev = {
+ .platform_data = cambria_uart_data,
+ },
+ .num_resources = 1,
+ .resource = &cambria_uart_resource,
+};
+
+static struct resource cambria_pata_resources[] = {
+ {
+ .flags = IORESOURCE_MEM
+ },
+ {
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .name = "intrq",
+ .start = IRQ_IXP4XX_GPIO12,
+ .end = IRQ_IXP4XX_GPIO12,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct ixp4xx_pata_data cambria_pata_data = {
+ .cs0_bits = 0xbfff3c03,
+ .cs1_bits = 0xbfff3c03,
+};
+
+static struct platform_device cambria_pata = {
+ .name = "pata_ixp4xx_cf",
+ .id = 0,
+ .dev.platform_data = &cambria_pata_data,
+ .num_resources = ARRAY_SIZE(cambria_pata_resources),
+ .resource = cambria_pata_resources,
+};
+
+static struct eth_plat_info cambria_npec_data = {
+ .phy = 1,
+ .rxq = 4,
+ .txreadyq = 21,
+};
+
+static struct eth_plat_info cambria_npea_data = {
+ .phy = 2,
+ .rxq = 2,
+ .txreadyq = 19,
+};
+
+static struct platform_device cambria_npec_device = {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEC,
+ .dev.platform_data = &cambria_npec_data,
+};
+
+static struct platform_device cambria_npea_device = {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEA,
+ .dev.platform_data = &cambria_npea_data,
+};
+
+static struct gpio_led cambria_gpio_leds[] = {
+ {
+ .name = "user", /* green led */
+ .gpio = 5,
+ .active_low = 1,
+ }
+};
+
+static struct gpio_led_platform_data cambria_gpio_leds_data = {
+ .num_leds = 1,
+ .leds = cambria_gpio_leds,
+};
+
+static struct platform_device cambria_gpio_leds_device = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev.platform_data = &cambria_gpio_leds_data,
+};
+
+
+static struct latch_led cambria_latch_leds[] = {
+ {
+ .name = "ledA", /* green led */
+ .bit = 0,
+ },
+ {
+ .name = "ledB", /* green led */
+ .bit = 1,
+ },
+ {
+ .name = "ledC", /* green led */
+ .bit = 2,
+ },
+ {
+ .name = "ledD", /* green led */
+ .bit = 3,
+ },
+ {
+ .name = "ledE", /* green led */
+ .bit = 4,
+ },
+ {
+ .name = "ledF", /* green led */
+ .bit = 5,
+ },
+ {
+ .name = "ledG", /* green led */
+ .bit = 6,
+ },
+ {
+ .name = "ledH", /* green led */
+ .bit = 7,
+ }
+};
+
+static struct latch_led_platform_data cambria_latch_leds_data = {
+ .num_leds = 8,
+ .leds = cambria_latch_leds,
+ .mem = 0x53F40000,
+};
+
+static struct platform_device cambria_latch_leds_device = {
+ .name = "leds-latch",
+ .id = -1,
+ .dev.platform_data = &cambria_latch_leds_data,
+};
+
+static struct resource cambria_usb0_resources[] = {
+ {
+ .start = 0xCD000000,
+ .end = 0xCD000300,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = 32,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct resource cambria_usb1_resources[] = {
+ {
+ .start = 0xCE000000,
+ .end = 0xCE000300,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = 33,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static u64 ehci_dma_mask = ~(u32)0;
+
+static struct platform_device cambria_usb0_device = {
+ .name = "ixp4xx-ehci",
+ .id = 0,
+ .resource = cambria_usb0_resources,
+ .num_resources = ARRAY_SIZE(cambria_usb0_resources),
+ .dev = {
+ .dma_mask = &ehci_dma_mask,
+ .coherent_dma_mask = 0xffffffff,
+ },
+};
+
+static struct platform_device cambria_usb1_device = {
+ .name = "ixp4xx-ehci",
+ .id = 1,
+ .resource = cambria_usb1_resources,
+ .num_resources = ARRAY_SIZE(cambria_usb1_resources),
+ .dev = {
+ .dma_mask = &ehci_dma_mask,
+ .coherent_dma_mask = 0xffffffff,
+ },
+};
+
+static struct platform_device *cambria_devices[] __initdata = {
+ &cambria_i2c_gpio,
+ &cambria_flash,
+ &cambria_uart,
+};
+
+static void __init cambria_gw23xx_setup(void)
+{
+ platform_device_register(&cambria_npec_device);
+ platform_device_register(&cambria_npea_device);
+}
+
+#ifdef CONFIG_SENSORS_EEPROM
+static void __init cambria_gw2350_setup(void)
+{
+ platform_device_register(&cambria_npec_device);
+ platform_device_register(&cambria_npea_device);
+
+ platform_device_register(&cambria_usb0_device);
+ platform_device_register(&cambria_usb1_device);
+
+ platform_device_register(&cambria_gpio_leds_device);
+}
+
+static void __init cambria_gw2358_setup(void)
+{
+ platform_device_register(&cambria_npec_device);
+ platform_device_register(&cambria_npea_device);
+
+ platform_device_register(&cambria_usb0_device);
+ platform_device_register(&cambria_usb1_device);
+
+ platform_device_register(&cambria_pata);
+
+ platform_device_register(&cambria_latch_leds_device);
+}
+
+static struct cambria_board_info cambria_boards[] __initdata = {
+ {
+ .model = "GW2350",
+ .setup = cambria_gw2350_setup,
+ }, {
+ .model = "GW2358",
+ .setup = cambria_gw2358_setup,
+ }
+};
+
+static struct cambria_board_info * __init cambria_find_board_info(char *model)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(cambria_boards); i++) {
+ struct cambria_board_info *info = &cambria_boards[i];
+ if (strncmp(info->model, model, strlen(info->model)) == 0)
+ return info;
+ }
+
+ return NULL;
+}
+
+struct cambria_eeprom_header {
+ unsigned char mac0[ETH_ALEN];
+ unsigned char mac1[ETH_ALEN];
+ unsigned char res0[4];
+ unsigned char magic[2];
+ unsigned char config[14];
+ unsigned char model[16];
+};
+
+static int __init cambria_eeprom_notify(struct notifier_block *self,
+ unsigned long event, void *t)
+{
+ struct eeprom_data *ee = t;
+ struct cambria_eeprom_header hdr;
+
+ if (cambria_info)
+ return NOTIFY_DONE;
+
+ /* The eeprom is at address 0x51 */
+ if (event != EEPROM_REGISTER || ee->client.addr != 0x51)
+ return NOTIFY_DONE;
+
+ ee->attr->read(&ee->client.dev.kobj, ee->attr, (char *)&hdr,
+ 0, sizeof(hdr));
+
+ if (hdr.magic[0] != 'G' || hdr.magic[1] != 'W')
+ return NOTIFY_DONE;
+
+ memcpy(&cambria_npec_data.hwaddr, hdr.mac0, ETH_ALEN);
+ memcpy(&cambria_npea_data.hwaddr, hdr.mac1, ETH_ALEN);
+
+ cambria_info = cambria_find_board_info(hdr.model);
+
+ return NOTIFY_OK;
+}
+
+static struct notifier_block cambria_eeprom_notifier __initdata = {
+ .notifier_call = cambria_eeprom_notify
+};
+
+static void __init cambria_register_eeprom_notifier(void)
+{
+ register_eeprom_notifier(&cambria_eeprom_notifier);
+}
+
+static void __init cambria_unregister_eeprom_notifier(void)
+{
+ unregister_eeprom_notifier(&cambria_eeprom_notifier);
+}
+#else /* CONFIG_SENSORS_EEPROM */
+static inline void cambria_register_eeprom_notifier(void) {};
+static inline void cambria_unregister_eeprom_notifier(void) {};
+#endif /* CONFIG_SENSORS_EEPROM */
+
+static void __init cambria_init(void)
+{
+ ixp4xx_sys_init();
+
+ cambria_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+ cambria_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
+
+ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
+ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+
+ platform_add_devices(cambria_devices, ARRAY_SIZE(cambria_devices));
+
+ cambria_pata_resources[0].start = 0x53e00000;
+ cambria_pata_resources[0].end = 0x53e3ffff;
+
+ cambria_pata_resources[1].start = 0x53e40000;
+ cambria_pata_resources[1].end = 0x53e7ffff;
+
+ cambria_pata_data.cs0_cfg = IXP4XX_EXP_CS3;
+ cambria_pata_data.cs1_cfg = IXP4XX_EXP_CS3;
+
+ cambria_register_eeprom_notifier();
+}
+
+static int __init cambria_model_setup(void)
+{
+ if (!machine_is_cambria())
+ return 0;
+
+ if (cambria_info) {
+ printk(KERN_DEBUG "Running on Gateworks Cambria %s\n",
+ cambria_info->model);
+ cambria_info->setup();
+ } else {
+ printk(KERN_INFO "Unknown/missing Cambria model number"
+ " -- defaults will be used\n");
+ cambria_gw23xx_setup();
+ }
+
+ cambria_unregister_eeprom_notifier();
+ return 0;
+}
+late_initcall(cambria_model_setup);
+
+#ifdef CONFIG_MACH_CAMBRIA
+MACHINE_START(CAMBRIA, "Gateworks Cambria series")
+ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
+ .map_io = ixp4xx_map_io,
+ .init_irq = ixp4xx_init_irq,
+ .timer = &ixp4xx_timer,
+ .boot_params = 0x0100,
+ .init_machine = cambria_init,
+MACHINE_END
+#endif
--- a/include/asm-arm/arch-ixp4xx/hardware.h
+++ b/include/asm-arm/arch-ixp4xx/hardware.h
@@ -18,7 +18,7 @@
#define __ASM_ARCH_HARDWARE_H__
#define PCIBIOS_MIN_IO 0x00001000
-#define PCIBIOS_MIN_MEM (cpu_is_ixp43x() ? 0x40000000 : 0x48000000)
+#define PCIBIOS_MIN_MEM (cpu_is_ixp43x() ? 0x48000000 : 0x48000000)
/*
* We override the standard dma-mask routines for bouncing.

View File

@ -0,0 +1,97 @@
--- a/arch/arm/mach-ixp4xx/cambria-setup.c
+++ b/arch/arm/mach-ixp4xx/cambria-setup.c
@@ -36,6 +36,7 @@
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
+#include <linux/irq.h>
struct cambria_board_info {
unsigned char *model;
@@ -105,6 +106,43 @@
.resource = &cambria_uart_resource,
};
+static struct resource cambria_optional_uart_resources[] = {
+ {
+ .start = 0x52000000,
+ .end = 0x52000fff,
+ .flags = IORESOURCE_MEM
+ },
+ {
+ .start = 0x53000000,
+ .end = 0x53000fff,
+ .flags = IORESOURCE_MEM
+ }
+};
+
+static struct plat_serial8250_port cambria_optional_uart_data[] = {
+ {
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 0,
+ .uartclk = 1843200,
+ },
+ {
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 0,
+ .uartclk = 1843200,
+ },
+ { },
+};
+
+static struct platform_device cambria_optional_uart = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM1,
+ .dev.platform_data = cambria_optional_uart_data,
+ .num_resources = 2,
+ .resource = cambria_optional_uart_resources,
+};
+
static struct resource cambria_pata_resources[] = {
{
.flags = IORESOURCE_MEM
@@ -287,6 +325,19 @@
#ifdef CONFIG_SENSORS_EEPROM
static void __init cambria_gw2350_setup(void)
{
+ *IXP4XX_EXP_CS2 = 0xbfff0003;
+ set_irq_type(IRQ_IXP4XX_GPIO3, IRQT_BOTHEDGE);
+ cambria_optional_uart_data[0].mapbase = IXP4XX_EXP_BUS_BASE(2);
+ cambria_optional_uart_data[0].membase = (void __iomem *)ioremap(IXP4XX_EXP_BUS_BASE(2), 0x0fff);
+ cambria_optional_uart_data[0].irq = IRQ_IXP4XX_GPIO3;
+
+ *IXP4XX_EXP_CS3 = 0xbfff0003;
+ set_irq_type(IRQ_IXP4XX_GPIO4, IRQT_BOTHEDGE);
+ cambria_optional_uart_data[1].mapbase = IXP4XX_EXP_BUS_BASE(3);
+ cambria_optional_uart_data[1].membase = (void __iomem *)ioremap(IXP4XX_EXP_BUS_BASE(3), 0x0fff);
+ cambria_optional_uart_data[1].irq = IRQ_IXP4XX_GPIO4;
+
+ platform_device_register(&cambria_optional_uart);
platform_device_register(&cambria_npec_device);
platform_device_register(&cambria_npea_device);
@@ -298,6 +349,22 @@
static void __init cambria_gw2358_setup(void)
{
+ *IXP4XX_EXP_CS3 = 0xbfff0003;
+ set_irq_type(IRQ_IXP4XX_GPIO3, IRQT_BOTHEDGE);
+ cambria_optional_uart_data[0].mapbase = 0x53FC0000;
+ cambria_optional_uart_data[0].membase = (void __iomem *)ioremap(0x53FC0000, 0x0fff);
+ cambria_optional_uart_data[0].irq = IRQ_IXP4XX_GPIO3;
+
+ *IXP4XX_EXP_CS3 = 0xbfff0003;
+ set_irq_type(IRQ_IXP4XX_GPIO4, IRQT_BOTHEDGE);
+ cambria_optional_uart_data[1].mapbase = 0x53F80000;
+ cambria_optional_uart_data[1].membase = (void __iomem *)ioremap(0x53F80000, 0x0fff);
+ cambria_optional_uart_data[1].irq = IRQ_IXP4XX_GPIO4;
+
+ platform_device_register(&cambria_optional_uart);
+
+ cambria_npec_data.phy = 2;
+ cambria_npea_data.phy = 1;
platform_device_register(&cambria_npec_device);
platform_device_register(&cambria_npea_device);

View File

@ -0,0 +1,47 @@
--- a/arch/arm/mach-ixp4xx/cambria-setup.c
+++ b/arch/arm/mach-ixp4xx/cambria-setup.c
@@ -214,6 +214,21 @@
.dev.platform_data = &cambria_gpio_leds_data,
};
+static struct resource cambria_gpio_resources[] = {
+ {
+ .name = "gpio",
+ .flags = 0,
+ },
+};
+
+static struct platform_device cambria_gpio = {
+ .name = "GPIODEV",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(cambria_gpio_resources),
+ .resource = cambria_gpio_resources,
+};
+
+
static struct latch_led cambria_latch_leds[] = {
{
@@ -337,6 +352,11 @@
cambria_optional_uart_data[1].membase = (void __iomem *)ioremap(IXP4XX_EXP_BUS_BASE(3), 0x0fff);
cambria_optional_uart_data[1].irq = IRQ_IXP4XX_GPIO4;
+ cambria_gpio_resources[0].start = (1 << 0) | (1 << 1) | (1 << 2) | (1 << 3) | (1 << 4) |\
+ (1 << 5) | (1 << 8) | (1 << 9) | (1 << 12);
+ cambria_gpio_resources[0].end = cambria_gpio_resources[0].start;
+
+ platform_device_register(&cambria_gpio);
platform_device_register(&cambria_optional_uart);
platform_device_register(&cambria_npec_device);
platform_device_register(&cambria_npea_device);
@@ -361,6 +381,10 @@
cambria_optional_uart_data[1].membase = (void __iomem *)ioremap(0x53F80000, 0x0fff);
cambria_optional_uart_data[1].irq = IRQ_IXP4XX_GPIO4;
+ cambria_gpio_resources[0].start = (1 << 14);
+ cambria_gpio_resources[0].end = cambria_gpio_resources[0].start;
+
+ platform_device_register(&cambria_gpio);
platform_device_register(&cambria_optional_uart);
cambria_npec_data.phy = 2;

View File

@ -0,0 +1,11 @@
--- a/arch/arm/mach-ixp4xx/ixp4xx_npe.c
+++ b/arch/arm/mach-ixp4xx/ixp4xx_npe.c
@@ -592,6 +592,8 @@
npe_reset(npe);
#endif
+ print_npe(KERN_INFO, npe, "firmware's license can be found in /usr/share/doc/LICENSE.IPL\n");
+
print_npe(KERN_INFO, npe, "firmware functionality 0x%X, "
"revision 0x%X:%X\n", (image->id >> 16) & 0xFF,
(image->id >> 8) & 0xFF, image->id & 0xFF);

View File

@ -0,0 +1,246 @@
--- a/drivers/net/arm/ixp4xx_eth.c
+++ b/drivers/net/arm/ixp4xx_eth.c
@@ -165,14 +165,15 @@
struct net_device *netdev;
struct napi_struct napi;
struct net_device_stats stat;
- struct mii_if_info mii;
+ struct mii_if_info mii[IXP4XX_ETH_PHY_MAX_ADDR];
struct delayed_work mdio_thread;
struct eth_plat_info *plat;
buffer_t *rx_buff_tab[RX_DESCS], *tx_buff_tab[TX_DESCS];
struct desc *desc_tab; /* coherent */
u32 desc_tab_phys;
int id; /* logical port ID */
- u16 mii_bmcr;
+ u16 mii_bmcr[IXP4XX_ETH_PHY_MAX_ADDR];
+ int phy_count;
};
/* NPE message structure */
@@ -316,12 +317,13 @@
spin_unlock_irqrestore(&mdio_lock, flags);
}
-static void phy_reset(struct net_device *dev, int phy_id)
+static void phy_reset(struct net_device *dev, int idx)
{
struct port *port = netdev_priv(dev);
+ int phy_id = port->mii[idx].phy_id;
int cycles = 0;
- mdio_write(dev, phy_id, MII_BMCR, port->mii_bmcr | BMCR_RESET);
+ mdio_write(dev, phy_id, MII_BMCR, port->mii_bmcr[idx] | BMCR_RESET);
while (cycles < MAX_MII_RESET_RETRIES) {
if (!(mdio_read(dev, phy_id, MII_BMCR) & BMCR_RESET)) {
@@ -335,12 +337,12 @@
cycles++;
}
- printk(KERN_ERR "%s: MII reset failed\n", dev->name);
+ printk(KERN_ERR "%s: MII reset failed on PHY%2d\n", dev->name, phy_id);
}
-static void eth_set_duplex(struct port *port)
+static void eth_set_duplex(struct port *port, int full_duplex)
{
- if (port->mii.full_duplex)
+ if (full_duplex)
__raw_writel(DEFAULT_TX_CNTRL0 & ~TX_CNTRL0_HALFDUPLEX,
&port->regs->tx_control[0]);
else
@@ -348,7 +350,7 @@
&port->regs->tx_control[0]);
}
-
+#if 0
static void phy_check_media(struct port *port, int init)
{
if (mii_check_media(&port->mii, 1, init))
@@ -367,7 +369,63 @@
}
}
}
+#else
+static void phy_update_link(struct net_device *dev, int link)
+{
+ int prev_link = netif_carrier_ok(dev);
+
+ if (!prev_link && link) {
+ printk(KERN_INFO "%s: link up\n", dev->name);
+ netif_carrier_on(dev);
+ } else if (prev_link && !link) {
+ printk(KERN_INFO "%s: link down\n", dev->name);
+ netif_carrier_off(dev);
+ }
+}
+
+static void phy_check_media(struct port *port, int init)
+{
+ struct net_device *dev = port->netdev;
+
+ if (port->phy_count == 1) {
+ struct mii_if_info *mii = &port->mii[0];
+
+ if (mii_check_media(mii, 1, init))
+ eth_set_duplex(port, mii->full_duplex);
+
+ if (mii->force_media) /* mii_check_media() doesn't work */
+ phy_update_link(dev, mii_link_ok(mii));
+ } else {
+ int cur_link = 0;
+ int i;
+
+ if (init)
+ eth_set_duplex(port, 1);
+
+ for (i = 0; i < port->phy_count; i++)
+ cur_link |= mii_link_ok(&port->mii[i]);
+
+ phy_update_link(dev, cur_link);
+ }
+}
+#endif
+
+static void phy_power_down(struct net_device *dev, int idx)
+{
+ struct port *port = netdev_priv(dev);
+ int phy_id = port->mii[idx].phy_id;
+
+ port->mii_bmcr[idx] = mdio_read(dev, phy_id, MII_BMCR) &
+ ~(BMCR_RESET | BMCR_PDOWN);
+ mdio_write(dev, phy_id, MII_BMCR, port->mii_bmcr[idx] | BMCR_PDOWN);
+}
+
+static void phy_power_up(struct net_device *dev, int idx)
+{
+ struct port *port = netdev_priv(dev);
+ mdio_write(dev, port->mii[idx].phy_id, MII_BMCR, port->mii_bmcr[idx]);
+}
static void mdio_thread(struct work_struct *work)
{
@@ -792,9 +850,12 @@
if (!netif_running(dev))
return -EINVAL;
- err = generic_mii_ioctl(&port->mii, if_mii(req), cmd, &duplex_chg);
+ if (port->phy_count != 1)
+ return -EOPNOTSUPP;
+
+ err = generic_mii_ioctl(&port->mii[0], if_mii(req), cmd, &duplex_chg);
if (duplex_chg)
- eth_set_duplex(port);
+ eth_set_duplex(port, port->mii[0].full_duplex);
return err;
}
@@ -947,7 +1008,8 @@
}
}
- mdio_write(dev, port->plat->phy, MII_BMCR, port->mii_bmcr);
+ for (i = 0; i < port->phy_count; i++)
+ phy_power_up(dev, i);
memset(&msg, 0, sizeof(msg));
msg.cmd = NPE_VLAN_SETRXQOSENTRY;
@@ -1107,10 +1169,8 @@
printk(KERN_CRIT "%s: unable to disable loopback\n",
dev->name);
- port->mii_bmcr = mdio_read(dev, port->plat->phy, MII_BMCR) &
- ~(BMCR_RESET | BMCR_PDOWN); /* may have been altered */
- mdio_write(dev, port->plat->phy, MII_BMCR,
- port->mii_bmcr | BMCR_PDOWN);
+ for (i = 0; i < port->phy_count; i++)
+ phy_power_down(dev, i);
if (!ports_open)
qmgr_disable_irq(TXDONE_QUEUE);
@@ -1120,6 +1180,42 @@
return 0;
}
+static void eth_add_phy(struct net_device *dev, int phy_id)
+{
+ struct port *port = netdev_priv(dev);
+ int i;
+
+ i = port->phy_count++;
+
+ port->mii[i].dev = dev;
+ port->mii[i].mdio_read = mdio_read;
+ port->mii[i].mdio_write = mdio_write;
+ port->mii[i].phy_id = phy_id;
+ port->mii[i].phy_id_mask = 0x1F;
+ port->mii[i].reg_num_mask = 0x1F;
+
+ printk(KERN_INFO "%s: MII PHY %i on %s\n", dev->name, phy_id,
+ npe_name(port->npe));
+
+ phy_reset(dev, i);
+ phy_power_down(dev, i);
+}
+
+static void eth_init_mii(struct net_device *dev)
+{
+ struct port *port = netdev_priv(dev);
+
+ if (port->plat->phy < IXP4XX_ETH_PHY_MAX_ADDR) {
+ eth_add_phy(dev, port->plat->phy);
+ } else {
+ int i;
+ for (i = 0; i < IXP4XX_ETH_PHY_MAX_ADDR; i++)
+ if (port->plat->phy_mask & (1U << i))
+ eth_add_phy(dev, i);
+ }
+
+}
+
static int __devinit eth_init_one(struct platform_device *pdev)
{
struct port *port;
@@ -1192,20 +1288,7 @@
__raw_writel(DEFAULT_CORE_CNTRL, &port->regs->core_control);
udelay(50);
- port->mii.dev = dev;
- port->mii.mdio_read = mdio_read;
- port->mii.mdio_write = mdio_write;
- port->mii.phy_id = plat->phy;
- port->mii.phy_id_mask = 0x1F;
- port->mii.reg_num_mask = 0x1F;
-
- printk(KERN_INFO "%s: MII PHY %i on %s\n", dev->name, plat->phy,
- npe_name(port->npe));
-
- phy_reset(dev, plat->phy);
- port->mii_bmcr = mdio_read(dev, plat->phy, MII_BMCR) &
- ~(BMCR_RESET | BMCR_PDOWN);
- mdio_write(dev, plat->phy, MII_BMCR, port->mii_bmcr | BMCR_PDOWN);
+ eth_init_mii(dev);
INIT_DELAYED_WORK(&port->mdio_thread, mdio_thread);
return 0;
--- a/include/asm-arm/arch-ixp4xx/platform.h
+++ b/include/asm-arm/arch-ixp4xx/platform.h
@@ -95,12 +95,15 @@
#define IXP4XX_ETH_NPEB 0x10
#define IXP4XX_ETH_NPEC 0x20
+#define IXP4XX_ETH_PHY_MAX_ADDR 32
+
/* Information about built-in Ethernet MAC interfaces */
struct eth_plat_info {
u8 phy; /* MII PHY ID, 0 - 31 */
u8 rxq; /* configurable, currently 0 - 31 only */
u8 txreadyq;
u8 hwaddr[6];
+ u32 phy_mask;
};
/* Information about built-in HSS (synchronous serial) interfaces */

View File

@ -0,0 +1,42 @@
--- a/drivers/net/arm/ixp4xx_eth.c
+++ b/drivers/net/arm/ixp4xx_eth.c
@@ -322,8 +322,12 @@
struct port *port = netdev_priv(dev);
int phy_id = port->mii[idx].phy_id;
int cycles = 0;
+ u16 bmcr;
- mdio_write(dev, phy_id, MII_BMCR, port->mii_bmcr[idx] | BMCR_RESET);
+ /* reset the PHY */
+ bmcr = mdio_read(dev, phy_id, MII_BMCR);
+ bmcr |= BMCR_ANENABLE;
+ mdio_write(dev, phy_id, MII_BMCR, bmcr | BMCR_RESET);
while (cycles < MAX_MII_RESET_RETRIES) {
if (!(mdio_read(dev, phy_id, MII_BMCR) & BMCR_RESET)) {
@@ -331,13 +335,23 @@
printk(KERN_DEBUG "%s: phy_reset() took %i cycles\n",
dev->name, cycles);
#endif
- return;
+ break;
}
udelay(1);
cycles++;
}
- printk(KERN_ERR "%s: MII reset failed on PHY%2d\n", dev->name, phy_id);
+ if (cycles == MAX_MII_RESET_RETRIES) {
+ printk(KERN_ERR "%s: MII reset failed on PHY%2d\n", dev->name,
+ phy_id);
+ return;
+ }
+
+ /* restart auto negotiation */
+ bmcr = mdio_read(dev, phy_id, MII_BMCR);
+ bmcr |= (BMCR_ANENABLE | BMCR_ANRESTART);
+ mdio_write(dev, phy_id, MII_BMCR, bmcr);
+
}
static void eth_set_duplex(struct port *port, int full_duplex)

View File

@ -0,0 +1,82 @@
--- a/arch/arm/mach-ixp4xx/ixp4xx_npe.c
+++ b/arch/arm/mach-ixp4xx/ixp4xx_npe.c
@@ -575,8 +575,8 @@
for (i = 0; i < image->size; i++)
image->data[i] = swab32(image->data[i]);
- if (!cpu_is_ixp46x() && ((image->id >> 28) & 0xF /* device ID */)) {
- print_npe(KERN_INFO, npe, "IXP46x firmware ignored on "
+ if (cpu_is_ixp42x() && ((image->id >> 28) & 0xF /* device ID */)) {
+ print_npe(KERN_INFO, npe, "IXP46x/IXP43x firmware ignored on "
"IXP42x\n");
goto err;
}
@@ -598,7 +598,7 @@
"revision 0x%X:%X\n", (image->id >> 16) & 0xFF,
(image->id >> 8) & 0xFF, image->id & 0xFF);
- if (!cpu_is_ixp46x()) {
+ if (cpu_is_ixp42x()) {
if (!npe->id)
instr_size = NPE_A_42X_INSTR_SIZE;
else
--- a/drivers/net/arm/ixp4xx_eth.c
+++ b/drivers/net/arm/ixp4xx_eth.c
@@ -32,6 +32,7 @@
#include <linux/kernel.h>
#include <linux/mii.h>
#include <linux/platform_device.h>
+#include <asm/arch/cpu.h>
#include <asm/arch/npe.h>
#include <asm/arch/qmgr.h>
@@ -1338,12 +1339,16 @@
static int __init eth_init_module(void)
{
- if (!(ixp4xx_read_feature_bits() & IXP4XX_FEATURE_NPEB_ETH0))
- return -ENOSYS;
- /* All MII PHY accesses use NPE-B Ethernet registers */
spin_lock_init(&mdio_lock);
- mdio_regs = (struct eth_regs __iomem *)IXP4XX_EthB_BASE_VIRT;
+ if (!cpu_is_ixp43x())
+ /* All MII PHY accesses use NPE-B Ethernet registers */
+ mdio_regs = (struct eth_regs __iomem *)IXP4XX_EthB_BASE_VIRT;
+
+ else
+ /* IXP43x lacks NPE-B and uses NPE-C for MII PHY access */
+ mdio_regs = (struct eth_regs __iomem *)IXP4XX_EthC_BASE_VIRT;
+
__raw_writel(DEFAULT_CORE_CNTRL, &mdio_regs->core_control);
return platform_driver_register(&drv);
--- a/include/asm-arm/arch-ixp4xx/cpu.h
+++ b/include/asm-arm/arch-ixp4xx/cpu.h
@@ -34,6 +34,8 @@
val &= ~IXP4XX_FEATURE_RESERVED;
if (!cpu_is_ixp46x())
val &= ~IXP4XX_FEATURE_IXP46X_ONLY;
+ if (cpu_is_ixp42x())
+ val &= ~IXP4XX_FEATURE_IXP43X_46X;
return val;
}
--- a/include/asm-arm/arch-ixp4xx/ixp4xx-regs.h
+++ b/include/asm-arm/arch-ixp4xx/ixp4xx-regs.h
@@ -628,11 +628,12 @@
#define IXP4XX_FEATURE_XSCALE_MAX_FREQ (3 << 22)
#define IXP4XX_FEATURE_RESERVED (0xFF << 24)
-#define IXP4XX_FEATURE_IXP46X_ONLY (IXP4XX_FEATURE_ECC_TIMESYNC | \
+#define IXP4XX_FEATURE_IXP43X_46X (IXP4XX_FEATURE_ECC_TIMESYNC | \
IXP4XX_FEATURE_USB_HOST | \
IXP4XX_FEATURE_NPEA_ETH | \
- IXP4XX_FEATURE_NPEB_ETH_1_TO_3 | \
- IXP4XX_FEATURE_RSA | \
IXP4XX_FEATURE_XSCALE_MAX_FREQ)
+#define IXP4XX_FEATURE_IXP46X_ONLY (IXP4XX_FEATURE_NPEB_ETH_1_TO_3 | \
+ IXP4XX_FEATURE_RSA)
+
#endif

File diff suppressed because it is too large Load Diff

View File

@ -0,0 +1,184 @@
--- a/drivers/i2c/chips/eeprom.c
+++ b/drivers/i2c/chips/eeprom.c
@@ -33,6 +33,8 @@
#include <linux/jiffies.h>
#include <linux/i2c.h>
#include <linux/mutex.h>
+#include <linux/notifier.h>
+#include <linux/eeprom.h>
/* Addresses to scan */
static const unsigned short normal_i2c[] = { 0x50, 0x51, 0x52, 0x53, 0x54,
@@ -41,26 +43,7 @@
/* Insmod parameters */
I2C_CLIENT_INSMOD_1(eeprom);
-
-/* Size of EEPROM in bytes */
-#define EEPROM_SIZE 256
-
-/* possible types of eeprom devices */
-enum eeprom_nature {
- UNKNOWN,
- VAIO,
-};
-
-/* Each client has this additional data */
-struct eeprom_data {
- struct i2c_client client;
- struct mutex update_lock;
- u8 valid; /* bitfield, bit!=0 if slice is valid */
- unsigned long last_updated[8]; /* In jiffies, 8 slices */
- u8 data[EEPROM_SIZE]; /* Register values */
- enum eeprom_nature nature;
-};
-
+ATOMIC_NOTIFIER_HEAD(eeprom_chain);
static int eeprom_attach_adapter(struct i2c_adapter *adapter);
static int eeprom_detect(struct i2c_adapter *adapter, int address, int kind);
@@ -197,6 +180,7 @@
data->valid = 0;
mutex_init(&data->update_lock);
data->nature = UNKNOWN;
+ data->attr = &eeprom_attr;
/* Tell the I2C layer a new client has arrived */
if ((err = i2c_attach_client(new_client)))
@@ -224,6 +208,9 @@
if (err)
goto exit_detach;
+ /* call the notifier chain */
+ atomic_notifier_call_chain(&eeprom_chain, EEPROM_REGISTER, data);
+
return 0;
exit_detach:
@@ -249,6 +236,41 @@
return 0;
}
+/**
+ * register_eeprom_notifier - register a 'user' of EEPROM devices.
+ * @nb: pointer to notifier info structure
+ *
+ * Registers a callback function to be called upon detection
+ * of an EEPROM device. Detection invokes the 'add' callback
+ * with the kobj of the mutex and a bin_attribute which allows
+ * read from the EEPROM. The intention is that the notifier
+ * will be able to read system configuration from the notifier.
+ *
+ * Only EEPROMs detected *after* the addition of the notifier
+ * are notified. I.e. EEPROMs already known to the system
+ * will not be notified - add the notifier from board level
+ * code!
+ */
+int register_eeprom_notifier(struct notifier_block *nb)
+{
+ return atomic_notifier_chain_register(&eeprom_chain, nb);
+}
+
+/**
+ * unregister_eeprom_notifier - unregister a 'user' of EEPROM devices.
+ * @old: pointer to notifier info structure
+ *
+ * Removes a callback function from the list of 'users' to be
+ * notified upon detection of EEPROM devices.
+ */
+int unregister_eeprom_notifier(struct notifier_block *nb)
+{
+ return atomic_notifier_chain_unregister(&eeprom_chain, nb);
+}
+
+EXPORT_SYMBOL_GPL(register_eeprom_notifier);
+EXPORT_SYMBOL_GPL(unregister_eeprom_notifier);
+
static int __init eeprom_init(void)
{
return i2c_add_driver(&eeprom_driver);
--- /dev/null
+++ b/include/linux/eeprom.h
@@ -0,0 +1,71 @@
+#ifndef _LINUX_EEPROM_H
+#define _LINUX_EEPROM_H
+/*
+ * EEPROM notifier header
+ *
+ * Copyright (C) 2006 John Bowler
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef __KERNEL__
+#error This is a kernel header
+#endif
+
+#include <linux/list.h>
+#include <linux/kobject.h>
+#include <linux/sysfs.h>
+
+/* Size of EEPROM in bytes */
+#define EEPROM_SIZE 256
+
+/* possible types of eeprom devices */
+enum eeprom_nature {
+ UNKNOWN,
+ VAIO,
+};
+
+/* Each client has this additional data */
+struct eeprom_data {
+ struct i2c_client client;
+ struct mutex update_lock;
+ u8 valid; /* bitfield, bit!=0 if slice is valid */
+ unsigned long last_updated[8]; /* In jiffies, 8 slices */
+ u8 data[EEPROM_SIZE]; /* Register values */
+ enum eeprom_nature nature;
+ struct bin_attribute *attr;
+};
+
+/*
+ * This is very basic.
+ *
+ * If an EEPROM is detected on the I2C bus (this only works for
+ * I2C EEPROMs) the notifier chain is called with
+ * both the I2C information and the kobject for the sysfs
+ * device which has been registers. It is then possible to
+ * read from the device via the bin_attribute::read method
+ * to extract configuration information.
+ *
+ * Register the notifier in the board level code, there is no
+ * need to unregister it but you can if you want (it will save
+ * a little bit or kernel memory to do so).
+ */
+
+extern int register_eeprom_notifier(struct notifier_block *nb);
+extern int unregister_eeprom_notifier(struct notifier_block *nb);
+
+#endif /* _LINUX_EEPROM_H */
--- a/include/linux/notifier.h
+++ b/include/linux/notifier.h
@@ -253,5 +253,8 @@
#define VT_UPDATE 0x0004 /* A bigger update occurred */
#define VT_PREWRITE 0x0005 /* A char is about to be written to the console */
+/* eeprom notifier chain */
+#define EEPROM_REGISTER 0x0001
+
#endif /* __KERNEL__ */
#endif /* _LINUX_NOTIFIER_H */

View File

@ -0,0 +1,190 @@
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -117,6 +117,12 @@
outputs. To be useful the particular board must have LEDs
and they must be connected to the GPIO lines.
+config LEDS_LATCH
+ tristate "LED Support for Memory Latched LEDs"
+ depends on LEDS_CLASS
+ help
+ -- To Do --
+
config LEDS_CM_X270
tristate "LED Support for the CM-X270 LEDs"
depends on LEDS_CLASS && MACH_ARMCORE
--- /dev/null
+++ b/drivers/leds/leds-latch.c
@@ -0,0 +1,141 @@
+/*
+ * LEDs driver for Memory Latched Devices
+ *
+ * Copyright (C) 2008 Gateworks Corp.
+ * Chris Lang <clang@gateworks.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/leds.h>
+#include <linux/workqueue.h>
+#include <asm/io.h>
+#include <linux/spinlock.h>
+
+static unsigned int mem_keep = 0xFF;
+static spinlock_t mem_lock;
+static unsigned char *iobase;
+
+struct latch_led_data {
+ struct led_classdev cdev;
+ struct work_struct work;
+ u8 new_level;
+ u8 bit;
+};
+
+static void latch_led_set(struct led_classdev *led_cdev,
+ enum led_brightness value)
+{
+ struct latch_led_data *led_dat =
+ container_of(led_cdev, struct latch_led_data, cdev);
+
+ spin_lock(mem_lock);
+
+ if (value == LED_OFF)
+ mem_keep |= (0x1 << led_dat->bit);
+ else
+ mem_keep &= ~(0x1 << led_dat->bit);
+
+ writeb(mem_keep, iobase);
+
+ spin_unlock(mem_lock);
+}
+
+static int latch_led_probe(struct platform_device *pdev)
+{
+ struct latch_led_platform_data *pdata = pdev->dev.platform_data;
+ struct latch_led *cur_led;
+ struct latch_led_data *leds_data, *led_dat;
+ int i, ret = 0;
+
+ if (!pdata)
+ return -EBUSY;
+
+ leds_data = kzalloc(sizeof(struct latch_led_data) * pdata->num_leds,
+ GFP_KERNEL);
+ if (!leds_data)
+ return -ENOMEM;
+
+ iobase = ioremap_nocache(pdata->mem, 0x1000);
+ writeb(0xFF, iobase);
+
+ for (i = 0; i < pdata->num_leds; i++) {
+ cur_led = &pdata->leds[i];
+ led_dat = &leds_data[i];
+
+ led_dat->cdev.name = cur_led->name;
+ led_dat->cdev.default_trigger = cur_led->default_trigger;
+ led_dat->cdev.brightness_set = latch_led_set;
+ led_dat->cdev.brightness = LED_OFF;
+ led_dat->bit = cur_led->bit;
+
+ ret = led_classdev_register(&pdev->dev, &led_dat->cdev);
+ if (ret < 0) {
+ goto err;
+ }
+ }
+
+ platform_set_drvdata(pdev, leds_data);
+
+ return 0;
+
+err:
+ if (i > 0) {
+ for (i = i - 1; i >= 0; i--) {
+ led_classdev_unregister(&leds_data[i].cdev);
+ }
+ }
+
+ kfree(leds_data);
+
+ return ret;
+}
+
+static int __devexit latch_led_remove(struct platform_device *pdev)
+{
+ int i;
+ struct latch_led_platform_data *pdata = pdev->dev.platform_data;
+ struct latch_led_data *leds_data;
+
+ leds_data = platform_get_drvdata(pdev);
+
+ for (i = 0; i < pdata->num_leds; i++) {
+ led_classdev_unregister(&leds_data[i].cdev);
+ cancel_work_sync(&leds_data[i].work);
+ }
+
+ kfree(leds_data);
+
+ return 0;
+}
+
+static struct platform_driver latch_led_driver = {
+ .probe = latch_led_probe,
+ .remove = __devexit_p(latch_led_remove),
+ .driver = {
+ .name = "leds-latch",
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init latch_led_init(void)
+{
+ return platform_driver_register(&latch_led_driver);
+}
+
+static void __exit latch_led_exit(void)
+{
+ platform_driver_unregister(&latch_led_driver);
+}
+
+module_init(latch_led_init);
+module_exit(latch_led_exit);
+
+MODULE_AUTHOR("Chris Lang <clang@gateworks.com>");
+MODULE_DESCRIPTION("Latch LED driver");
+MODULE_LICENSE("GPL");
--- a/drivers/leds/Makefile
+++ b/drivers/leds/Makefile
@@ -18,6 +18,7 @@
obj-$(CONFIG_LEDS_COBALT_QUBE) += leds-cobalt-qube.o
obj-$(CONFIG_LEDS_COBALT_RAQ) += leds-cobalt-raq.o
obj-$(CONFIG_LEDS_GPIO) += leds-gpio.o
+obj-$(CONFIG_LEDS_LATCH) += leds-latch.o
obj-$(CONFIG_LEDS_CM_X270) += leds-cm-x270.o
obj-$(CONFIG_LEDS_CLEVO_MAIL) += leds-clevo-mail.o
obj-$(CONFIG_LEDS_HP6XX) += leds-hp6xx.o
--- a/include/linux/leds.h
+++ b/include/linux/leds.h
@@ -134,5 +134,18 @@
unsigned long *delay_off);
};
+/* For the leds-latch driver */
+struct latch_led {
+ const char *name;
+ char *default_trigger;
+ unsigned bit;
+};
+
+struct latch_led_platform_data {
+ int num_leds;
+ u32 mem;
+ struct latch_led *leds;
+};
+
#endif /* __LINUX_LEDS_H_INCLUDED */

View File

@ -0,0 +1,43 @@
--- a/arch/arm/mach-ixp4xx/avila-setup.c
+++ b/arch/arm/mach-ixp4xx/avila-setup.c
@@ -132,6 +132,31 @@
.resource = avila_pata_resources,
};
+/* Built-in 10/100 Ethernet MAC interfaces */
+static struct eth_plat_info avila_npeb_data = {
+ .phy = 0,
+ .rxq = 3,
+ .txreadyq = 20,
+};
+
+static struct eth_plat_info avila_npec_data = {
+ .phy = 1,
+ .rxq = 4,
+ .txreadyq = 21,
+};
+
+static struct platform_device avila_npeb_device = {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = &avila_npeb_data,
+};
+
+static struct platform_device avila_npec_device = {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEC,
+ .dev.platform_data = &avila_npec_data,
+};
+
static struct platform_device *avila_devices[] __initdata = {
&avila_i2c_gpio,
&avila_flash,
@@ -159,6 +184,8 @@
platform_device_register(&avila_pata);
+ platform_device_register(avila_npeb_device);
+ platform_device_register(avila_npec_device);
}
MACHINE_START(AVILA, "Gateworks Avila Network Platform")

View File

@ -0,0 +1,227 @@
--- a/arch/arm/mach-ixp4xx/avila-setup.c
+++ b/arch/arm/mach-ixp4xx/avila-setup.c
@@ -14,10 +14,18 @@
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/device.h>
+#include <linux/if_ether.h>
+#include <linux/socket.h>
+#include <linux/netdevice.h>
#include <linux/serial.h>
#include <linux/tty.h>
#include <linux/serial_8250.h>
#include <linux/slab.h>
+#ifdef CONFIG_SENSORS_EEPROM
+# include <linux/i2c.h>
+# include <linux/eeprom.h>
+#endif
+
#include <linux/i2c-gpio.h>
#include <asm/types.h>
@@ -29,6 +37,13 @@
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
+struct avila_board_info {
+ unsigned char *model;
+ void (* setup)(void);
+};
+
+static struct avila_board_info *avila_info __initdata;
+
static struct flash_platform_data avila_flash_data = {
.map_name = "cfi_probe",
.width = 2,
@@ -163,10 +178,160 @@
&avila_uart
};
+static void __init avila_gw23xx_setup(void)
+{
+ platform_device_register(&avila_npeb_device);
+ platform_device_register(&avila_npec_device);
+}
+
+#ifdef CONFIG_SENSORS_EEPROM
+static void __init avila_gw2342_setup(void)
+{
+ platform_device_register(&avila_npeb_device);
+ platform_device_register(&avila_npec_device);
+}
+
+static void __init avila_gw2345_setup(void)
+{
+ avila_npeb_data.phy = IXP4XX_ETH_PHY_MAX_ADDR;
+ avila_npeb_data.phy_mask = 0x1e; /* ports 1-4 of the KS8995 switch */
+ platform_device_register(&avila_npeb_device);
+
+ avila_npec_data.phy = 5; /* port 5 of the KS8995 switch */
+ platform_device_register(&avila_npec_device);
+}
+
+static void __init avila_gw2347_setup(void)
+{
+ platform_device_register(&avila_npeb_device);
+}
+
+static void __init avila_gw2348_setup(void)
+{
+ platform_device_register(&avila_npeb_device);
+ platform_device_register(&avila_npec_device);
+}
+
+static void __init avila_gw2353_setup(void)
+{
+ platform_device_register(&avila_npeb_device);
+}
+
+static void __init avila_gw2355_setup(void)
+{
+ avila_npeb_data.phy = IXP4XX_ETH_PHY_MAX_ADDR;
+ avila_npeb_data.phy_mask = 0x1e; /* ports 1-4 of the KS8995 switch */
+ platform_device_register(&avila_npeb_device);
+
+ avila_npec_data.phy = 16;
+ platform_device_register(&avila_npec_device);
+}
+
+static void __init avila_gw2357_setup(void)
+{
+ platform_device_register(&avila_npeb_device);
+}
+
+static struct avila_board_info avila_boards[] __initdata = {
+ {
+ .model = "GW2342",
+ .setup = avila_gw2342_setup,
+ }, {
+ .model = "GW2345",
+ .setup = avila_gw2345_setup,
+ }, {
+ .model = "GW2347",
+ .setup = avila_gw2347_setup,
+ }, {
+ .model = "GW2348",
+ .setup = avila_gw2348_setup,
+ }, {
+ .model = "GW2353",
+ .setup = avila_gw2353_setup,
+ }, {
+ .model = "GW2355",
+ .setup = avila_gw2355_setup,
+ }, {
+ .model = "GW2357",
+ .setup = avila_gw2357_setup,
+ }
+};
+
+static struct avila_board_info * __init avila_find_board_info(char *model)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(avila_boards); i++) {
+ struct avila_board_info *info = &avila_boards[i];
+ if (strncmp(info->model, model, strlen(info->model)) == 0)
+ return info;
+ }
+
+ return NULL;
+}
+
+struct avila_eeprom_header {
+ unsigned char mac0[ETH_ALEN];
+ unsigned char mac1[ETH_ALEN];
+ unsigned char res0[4];
+ unsigned char magic[2];
+ unsigned char config[14];
+ unsigned char model[16];
+};
+
+static int __init avila_eeprom_notify(struct notifier_block *self,
+ unsigned long event, void *t)
+{
+ struct eeprom_data *ee = t;
+ struct avila_eeprom_header hdr;
+
+ if (avila_info)
+ return NOTIFY_DONE;
+
+ /* The eeprom is at address 0x51 */
+ if (event != EEPROM_REGISTER || ee->client.addr != 0x51)
+ return NOTIFY_DONE;
+
+ ee->attr->read(&ee->client.dev.kobj, ee->attr, (char *)&hdr,
+ 0, sizeof(hdr));
+
+ if (hdr.magic[0] != 'G' || hdr.magic[1] != 'W')
+ return NOTIFY_DONE;
+
+ memcpy(&avila_npeb_data.hwaddr, hdr.mac0, ETH_ALEN);
+ memcpy(&avila_npec_data.hwaddr, hdr.mac1, ETH_ALEN);
+
+ avila_info = avila_find_board_info(hdr.model);
+
+ return NOTIFY_OK;
+}
+
+static struct notifier_block avila_eeprom_notifier __initdata = {
+ .notifier_call = avila_eeprom_notify
+};
+
+static void __init avila_register_eeprom_notifier(void)
+{
+ register_eeprom_notifier(&avila_eeprom_notifier);
+}
+
+static void __init avila_unregister_eeprom_notifier(void)
+{
+ unregister_eeprom_notifier(&avila_eeprom_notifier);
+}
+#else /* CONFIG_SENSORS_EEPROM */
+static inline void avila_register_eeprom_notifier(void) {};
+static inline void avila_unregister_eeprom_notifier(void) {};
+#endif /* CONFIG_SENSORS_EEPROM */
+
static void __init avila_init(void)
{
ixp4xx_sys_init();
+ /*
+ * These devices are present on all Avila models and don't need any
+ * model specific setup.
+ */
avila_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
avila_flash_resource.end =
IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
@@ -184,9 +349,28 @@
platform_device_register(&avila_pata);
- platform_device_register(avila_npeb_device);
- platform_device_register(avila_npec_device);
+ avila_register_eeprom_notifier();
+}
+
+static int __init avila_model_setup(void)
+{
+ if (!machine_is_avila())
+ return 0;
+
+ if (avila_info) {
+ printk(KERN_DEBUG "Running on Gateworks Avila %s\n",
+ avila_info->model);
+ avila_info->setup();
+ } else {
+ printk(KERN_INFO "Unknown/missing Avila model number"
+ " -- defaults will be used\n");
+ avila_gw23xx_setup();
+ }
+
+ avila_unregister_eeprom_notifier();
+ return 0;
}
+late_initcall(avila_model_setup);
MACHINE_START(AVILA, "Gateworks Avila Network Platform")
/* Maintainer: Deepak Saxena <dsaxena@plexity.net> */

View File

@ -0,0 +1,172 @@
--- a/arch/arm/mach-ixp4xx/avila-setup.c
+++ b/arch/arm/mach-ixp4xx/avila-setup.c
@@ -26,6 +26,7 @@
# include <linux/eeprom.h>
#endif
+#include <linux/leds.h>
#include <linux/i2c-gpio.h>
#include <asm/types.h>
@@ -172,6 +173,72 @@
.dev.platform_data = &avila_npec_data,
};
+static struct gpio_led avila_gpio_leds[] = {
+ {
+ .name = "user", /* green led */
+ .gpio = AVILA_GW23XX_LED_USER_GPIO,
+ .active_low = 1,
+ }
+};
+
+static struct gpio_led_platform_data avila_gpio_leds_data = {
+ .num_leds = 1,
+ .leds = avila_gpio_leds,
+};
+
+static struct platform_device avila_gpio_leds_device = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev.platform_data = &avila_gpio_leds_data,
+};
+
+static struct latch_led avila_latch_leds[] = {
+ {
+ .name = "led0", /* green led */
+ .bit = 0,
+ },
+ {
+ .name = "led1", /* green led */
+ .bit = 1,
+ },
+ {
+ .name = "led2", /* green led */
+ .bit = 2,
+ },
+ {
+ .name = "led3", /* green led */
+ .bit = 3,
+ },
+ {
+ .name = "led4", /* green led */
+ .bit = 4,
+ },
+ {
+ .name = "led5", /* green led */
+ .bit = 5,
+ },
+ {
+ .name = "led6", /* green led */
+ .bit = 6,
+ },
+ {
+ .name = "led7", /* green led */
+ .bit = 7,
+ }
+};
+
+static struct latch_led_platform_data avila_latch_leds_data = {
+ .num_leds = 8,
+ .leds = avila_latch_leds,
+ .mem = 0x51000000,
+};
+
+static struct platform_device avila_latch_leds_device = {
+ .name = "leds-latch",
+ .id = -1,
+ .dev.platform_data = &avila_latch_leds_data,
+};
+
static struct platform_device *avila_devices[] __initdata = {
&avila_i2c_gpio,
&avila_flash,
@@ -182,6 +249,8 @@
{
platform_device_register(&avila_npeb_device);
platform_device_register(&avila_npec_device);
+
+ platform_device_register(&avila_gpio_leds_device);
}
#ifdef CONFIG_SENSORS_EEPROM
@@ -189,6 +258,8 @@
{
platform_device_register(&avila_npeb_device);
platform_device_register(&avila_npec_device);
+
+ platform_device_register(&avila_gpio_leds_device);
}
static void __init avila_gw2345_setup(void)
@@ -199,22 +270,30 @@
avila_npec_data.phy = 5; /* port 5 of the KS8995 switch */
platform_device_register(&avila_npec_device);
+
+ platform_device_register(&avila_gpio_leds_device);
}
static void __init avila_gw2347_setup(void)
{
platform_device_register(&avila_npeb_device);
+
+ avila_gpio_leds[0].gpio = AVILA_GW23X7_LED_USER_GPIO;
+ platform_device_register(&avila_gpio_leds_device);
}
static void __init avila_gw2348_setup(void)
{
platform_device_register(&avila_npeb_device);
platform_device_register(&avila_npec_device);
+
+ platform_device_register(&avila_gpio_leds_device);
}
static void __init avila_gw2353_setup(void)
{
platform_device_register(&avila_npeb_device);
+ platform_device_register(&avila_gpio_leds_device);
}
static void __init avila_gw2355_setup(void)
@@ -225,11 +304,29 @@
avila_npec_data.phy = 16;
platform_device_register(&avila_npec_device);
+
+ platform_device_register(&avila_gpio_leds_device);
+
+ *IXP4XX_EXP_CS4 |= 0xbfff3c03;
+ avila_latch_leds[0].name = "RXD";
+ avila_latch_leds[1].name = "TXD";
+ avila_latch_leds[2].name = "POL";
+ avila_latch_leds[3].name = "LNK";
+ avila_latch_leds[4].name = "ERR";
+ avila_latch_leds_data.num_leds = 5;
+ avila_latch_leds_data.mem = 0x54000000;
+ platform_device_register(&avila_latch_leds_device);
}
static void __init avila_gw2357_setup(void)
{
platform_device_register(&avila_npeb_device);
+
+ avila_gpio_leds[0].gpio = AVILA_GW23X7_LED_USER_GPIO;
+ platform_device_register(&avila_gpio_leds_device);
+
+ *IXP4XX_EXP_CS1 |= 0xbfff3c03;
+ platform_device_register(&avila_latch_leds_device);
}
static struct avila_board_info avila_boards[] __initdata = {
--- a/include/asm-arm/arch-ixp4xx/avila.h
+++ b/include/asm-arm/arch-ixp4xx/avila.h
@@ -36,4 +36,6 @@
#define AVILA_PCI_INTC_PIN 9
#define AVILA_PCI_INTD_PIN 8
-
+/* User LEDs */
+#define AVILA_GW23XX_LED_USER_GPIO 3
+#define AVILA_GW23X7_LED_USER_GPIO 4

View File

@ -0,0 +1,41 @@
--- a/arch/arm/mach-ixp4xx/avila-setup.c
+++ b/arch/arm/mach-ixp4xx/avila-setup.c
@@ -239,10 +239,28 @@
.dev.platform_data = &avila_latch_leds_data,
};
+static struct resource avila_gpio_resources[] = {
+ {
+ .name = "gpio",
+ /* FIXME: gpio mask should be model specific */
+ .start = AVILA_GPIO_MASK,
+ .end = AVILA_GPIO_MASK,
+ .flags = 0,
+ },
+};
+
+static struct platform_device avila_gpio = {
+ .name = "GPIODEV",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(avila_gpio_resources),
+ .resource = avila_gpio_resources,
+};
+
static struct platform_device *avila_devices[] __initdata = {
&avila_i2c_gpio,
&avila_flash,
- &avila_uart
+ &avila_uart,
+ &avila_gpio,
};
static void __init avila_gw23xx_setup(void)
--- a/include/asm-arm/arch-ixp4xx/avila.h
+++ b/include/asm-arm/arch-ixp4xx/avila.h
@@ -39,3 +39,6 @@
/* User LEDs */
#define AVILA_GW23XX_LED_USER_GPIO 3
#define AVILA_GW23X7_LED_USER_GPIO 4
+
+/* gpio mask used by platform device */
+#define AVILA_GPIO_MASK (1 << 1) | (1 << 3) | (1 << 5) | (1 << 7) | (1 << 9)

View File

@ -0,0 +1,46 @@
--- a/arch/arm/mach-ixp4xx/avila-setup.c
+++ b/arch/arm/mach-ixp4xx/avila-setup.c
@@ -294,6 +294,7 @@
static void __init avila_gw2347_setup(void)
{
+ avila_npeb_data.quirks |= IXP4XX_ETH_QUIRK_GW23X7;
platform_device_register(&avila_npeb_device);
avila_gpio_leds[0].gpio = AVILA_GW23X7_LED_USER_GPIO;
@@ -338,6 +339,7 @@
static void __init avila_gw2357_setup(void)
{
+ avila_npeb_data.quirks |= IXP4XX_ETH_QUIRK_GW23X7;
platform_device_register(&avila_npeb_device);
avila_gpio_leds[0].gpio = AVILA_GW23X7_LED_USER_GPIO;
--- a/drivers/net/arm/ixp4xx_eth.c
+++ b/drivers/net/arm/ixp4xx_eth.c
@@ -348,6 +348,14 @@
return;
}
+ if (port->plat->quirks & IXP4XX_ETH_QUIRK_GW23X7) {
+ mdio_write(dev, 1, 0x19,
+ (mdio_read(dev, 1, 0x19) & 0xfffe) | 0x8000);
+
+ printk(KERN_DEBUG "%s: phy_id of the DP83848 changed to 0\n",
+ dev->name);
+ }
+
/* restart auto negotiation */
bmcr = mdio_read(dev, phy_id, MII_BMCR);
bmcr |= (BMCR_ANENABLE | BMCR_ANRESTART);
--- a/include/asm-arm/arch-ixp4xx/platform.h
+++ b/include/asm-arm/arch-ixp4xx/platform.h
@@ -104,6 +104,8 @@
u8 txreadyq;
u8 hwaddr[6];
u32 phy_mask;
+ u32 quirks;
+#define IXP4XX_ETH_QUIRK_GW23X7 0x00000001
};
/* Information about built-in HSS (synchronous serial) interfaces */

View File

@ -0,0 +1,53 @@
--- a/arch/arm/mach-ixp4xx/gtwx5715-setup.c
+++ b/arch/arm/mach-ixp4xx/gtwx5715-setup.c
@@ -29,6 +29,8 @@
#include <linux/serial_8250.h>
#include <linux/slab.h>
+#include <linux/spi/spi_gpio.h>
+
#include <asm/types.h>
#include <asm/setup.h>
#include <asm/memory.h>
@@ -121,9 +123,41 @@
.resource = &gtwx5715_flash_resource,
};
+static int gtwx5715_spi_boardinfo_setup(struct spi_board_info *bi,
+ struct spi_master *master, void *data)
+{
+
+ strlcpy(bi->modalias, "spi-ks8995", sizeof(bi->modalias));
+
+ bi->max_speed_hz = 5000000 /* Hz */;
+ bi->bus_num = master->bus_num;
+ bi->mode = SPI_MODE_0;
+
+ return 0;
+}
+
+static struct spi_gpio_platform_data gtwx5715_spi_bus_data = {
+ .pin_cs = GTWX5715_KSSPI_SELECT,
+ .pin_clk = GTWX5715_KSSPI_CLOCK,
+ .pin_miso = GTWX5715_KSSPI_RXD,
+ .pin_mosi = GTWX5715_KSSPI_TXD,
+ .cs_activelow = 1,
+ .no_spi_delay = 1,
+ .boardinfo_setup = gtwx5715_spi_boardinfo_setup,
+};
+
+static struct platform_device gtwx5715_spi_bus = {
+ .name = "spi-gpio",
+ .id = 0,
+ .dev = {
+ .platform_data = &gtwx5715_spi_bus_data,
+ },
+};
+
static struct platform_device *gtwx5715_devices[] __initdata = {
&gtwx5715_uart_device,
&gtwx5715_flash,
+ &gtwx5715_spi_bus,
};
static void __init gtwx5715_init(void)

View File

@ -0,0 +1,40 @@
--- a/arch/arm/mach-ixp4xx/gtwx5715-setup.c
+++ b/arch/arm/mach-ixp4xx/gtwx5715-setup.c
@@ -154,10 +154,37 @@
},
};
+static struct eth_plat_info gtwx5715_npeb_data = {
+ .phy = IXP4XX_ETH_PHY_MAX_ADDR,
+ .phy_mask = 0x1e, /* ports 1-4 of the KS8995 switch */
+ .rxq = 3,
+ .txreadyq = 20,
+};
+
+static struct eth_plat_info gtwx5715_npec_data = {
+ .phy = 5, /* port 5 of the KS8995 switch */
+ .rxq = 4,
+ .txreadyq = 21,
+};
+
+static struct platform_device gtwx5715_npeb_device = {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = &gtwx5715_npeb_data,
+};
+
+static struct platform_device gtwx5715_npec_device = {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEC,
+ .dev.platform_data = &gtwx5715_npec_data,
+};
+
static struct platform_device *gtwx5715_devices[] __initdata = {
&gtwx5715_uart_device,
&gtwx5715_flash,
&gtwx5715_spi_bus,
+ &gtwx5715_npeb_device,
+ &gtwx5715_npec_device,
};
static void __init gtwx5715_init(void)

View File

@ -0,0 +1,137 @@
--- a/drivers/ata/pata_ixp4xx_cf.c
+++ b/drivers/ata/pata_ixp4xx_cf.c
@@ -24,17 +24,58 @@
#include <scsi/scsi_host.h>
#define DRV_NAME "pata_ixp4xx_cf"
-#define DRV_VERSION "0.2"
+#define DRV_VERSION "0.3"
static int ixp4xx_set_mode(struct ata_link *link, struct ata_device **error)
{
struct ata_device *dev;
+ struct ixp4xx_pata_data *data = link->ap->host->dev->platform_data;
+ unsigned int pio_mask;
ata_link_for_each_dev(dev, link) {
+ if (dev->id[ATA_ID_FIELD_VALID] & (1 << 1)){
+ pio_mask = dev->id[ATA_ID_PIO_MODES] & 0x03;
+ if (pio_mask & (1 << 1)){
+ pio_mask = 4;
+ }else{
+ pio_mask = 3;
+ }
+ }else{
+ pio_mask = (dev->id[ATA_ID_OLD_PIO_MODES] >> 8);
+ }
+ switch (pio_mask){
+ case 0:
+ ata_dev_printk(dev, KERN_INFO, "configured for PIO0\n");
+ dev->pio_mode = XFER_PIO_0;
+ dev->xfer_mode = XFER_PIO_0;
+ *data->cs0_cfg = 0x8a473c03;
+ break;
+ case 1:
+ ata_dev_printk(dev, KERN_INFO, "configured for PIO1\n");
+ dev->pio_mode = XFER_PIO_1;
+ dev->xfer_mode = XFER_PIO_1;
+ *data->cs0_cfg = 0x86433c03;
+ break;
+ case 2:
+ ata_dev_printk(dev, KERN_INFO, "configured for PIO2\n");
+ dev->pio_mode = XFER_PIO_2;
+ dev->xfer_mode = XFER_PIO_2;
+ *data->cs0_cfg = 0x82413c03;
+ break;
+ case 3:
+ ata_dev_printk(dev, KERN_INFO, "configured for PIO3\n");
+ dev->pio_mode = XFER_PIO_3;
+ dev->xfer_mode = XFER_PIO_3;
+ *data->cs0_cfg = 0x80823c03;
+ break;
+ case 4:
+ ata_dev_printk(dev, KERN_INFO, "configured for PIO4\n");
+ dev->pio_mode = XFER_PIO_4;
+ dev->xfer_mode = XFER_PIO_4;
+ *data->cs0_cfg = 0x80403c03;
+ break;
+ }
if (ata_dev_enabled(dev)) {
- ata_dev_printk(dev, KERN_INFO, "configured for PIO0\n");
- dev->pio_mode = XFER_PIO_0;
- dev->xfer_mode = XFER_PIO_0;
dev->xfer_shift = ATA_SHIFT_PIO;
dev->flags |= ATA_DFLAG_PIO;
}
@@ -48,6 +89,7 @@
unsigned int i;
unsigned int words = buflen >> 1;
u16 *buf16 = (u16 *) buf;
+ unsigned int pio_mask;
struct ata_port *ap = dev->link->ap;
void __iomem *mmio = ap->ioaddr.data_addr;
struct ixp4xx_pata_data *data = ap->host->dev->platform_data;
@@ -55,8 +97,34 @@
/* set the expansion bus in 16bit mode and restore
* 8 bit mode after the transaction.
*/
- *data->cs0_cfg &= ~(0x01);
- udelay(100);
+ if (dev->id[ATA_ID_FIELD_VALID] & (1 << 1)){
+ pio_mask = dev->id[ATA_ID_PIO_MODES] & 0x03;
+ if (pio_mask & (1 << 1)){
+ pio_mask = 4;
+ }else{
+ pio_mask = 3;
+ }
+ }else{
+ pio_mask = (dev->id[ATA_ID_OLD_PIO_MODES] >> 8);
+ }
+ switch (pio_mask){
+ case 0:
+ *data->cs0_cfg = 0xa9643c42;
+ break;
+ case 1:
+ *data->cs0_cfg = 0x85033c42;
+ break;
+ case 2:
+ *data->cs0_cfg = 0x80b23c42;
+ break;
+ case 3:
+ *data->cs0_cfg = 0x80823c42;
+ break;
+ case 4:
+ *data->cs0_cfg = 0x80403c42;
+ break;
+ }
+ udelay(5);
/* Transfer multiple of 2 bytes */
if (rw == READ)
@@ -81,8 +149,24 @@
words++;
}
- udelay(100);
- *data->cs0_cfg |= 0x01;
+ udelay(5);
+ switch (pio_mask){
+ case 0:
+ *data->cs0_cfg = 0x8a473c03;
+ break;
+ case 1:
+ *data->cs0_cfg = 0x86433c03;
+ break;
+ case 2:
+ *data->cs0_cfg = 0x82413c03;
+ break;
+ case 3:
+ *data->cs0_cfg = 0x80823c03;
+ break;
+ case 4:
+ *data->cs0_cfg = 0x80403c03;
+ break;
+ }
return words << 1;
}

View File

@ -0,0 +1,27 @@
--- a/arch/arm/common/dmabounce.c
+++ b/arch/arm/common/dmabounce.c
@@ -117,6 +117,10 @@
} else if (size <= device_info->large.size) {
pool = &device_info->large;
} else {
+#ifdef CONFIG_DMABOUNCE_DEBUG
+ printk(KERN_INFO "A dma bounce buffer outside the pool size was requested. Requested size was 0x%08X\nThe calling code was :\n", size);
+ dump_stack();
+#endif
pool = NULL;
}
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -236,6 +236,11 @@
default y
depends on PCI
+config DMABOUNCE_DEBUG
+ bool "Enable DMABounce debuging"
+ default n
+ depends on DMABOUNCE
+
config IXP4XX_INDIRECT_PCI
bool "Use indirect PCI memory access"
depends on PCI

View File

@ -0,0 +1,11 @@
--- a/include/asm-arm/arch-ixp4xx/avila.h
+++ b/include/asm-arm/arch-ixp4xx/avila.h
@@ -25,7 +25,7 @@
/*
* AVILA PCI IRQs
*/
-#define AVILA_PCI_MAX_DEV 4
+#define AVILA_PCI_MAX_DEV 6
#define LOFT_PCI_MAX_DEV 6
#define AVILA_PCI_IRQ_LINES 4