mirror of
https://github.com/openwrt/openwrt.git
synced 2025-02-02 17:20:59 +00:00
ath79: add support for Senao Engenius ESR900
FCC ID: A8J-ESR900
Engenius ESR900 is an indoor wireless router with
a gigabit ethernet switch, dual-band wireless,
internal antenna plates, and a USB 2.0 port
**Specification:**
- QCA9558 SOC 2.4 GHz, 3x3
- AR9580 WLAN PCIe on board, 5 GHz, 3x3
- AR8327N SW 4 ports LAN, 1 port WAN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM
- UART at J1 populated, RX grounded
- 6 internal antenna plates (omni-directional)
- 5 LEDs, 1 button (power, 2G, 5G, WAN, WPS) (reset)
**MAC addresses:**
Base MAC address labeled as "MAC ADDRESS"
MAC "wanaddr" is not similar to "ethaddr"
eth0 *:06 MAC u-boot-env ethaddr
phy0 *:06 MAC u-boot-env ethaddr
phy1 *:07 --- u-boot-env ethaddr +1
WAN *:6E:81 u-boot-env wanaddr
**Serial Access:**
RX on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin
**Installation:**
Method 1: Firmware upgrade page
OEM webpage at 192.168.0.1
username and password "admin"
Navigate to Settings (gear icon) --> Tools --> Firmware
select the factory.bin image
confirm and wait 3 minutes
Method 2: TFTP recovery
Follow TFTP instructions using initramfs.bin
use sysupgrade.bin to flash using openwrt web interface
**Return to OEM:**
MTD partitions should be backed up before flashing
using TFTP to boot openwrt without overwriting flash
Alternatively, it is possible to edit OEM firmware images
to flash MTD partitions in openwrt to restore OEM firmware
by removing the OEM header and writing the rest to "firmware"
**TFTP recovery:**
Requires serial console, reset button does nothing at boot
rename initramfs.bin to 'uImageESR900'
make available on TFTP server at 192.168.99.8
power board, interrupt boot by pressing '4' rapidly
execute tftpboot and bootm
**Note on ETH switch registers**
Registers must be written to the ethernet switch
in order to set up the switch's MAC interface.
U-boot can write the registers on it's own
which is needed, for example, in a TFTP transfer.
The register bits from OEM for the AR8327 switch
can be read from interrupted boot (tftpboot, bootm)
by adding print lines in the switch driver ar8327.c
before 'qca,ar8327-initvals' is parsed from DTS and written.
for example:
pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This commit is contained in:
Michael Pratt
Hauke Mehrtens
parent
2742705fa5
commit
2f99f7e2d0
85
target/linux/ath79/dts/qca9558_engenius_esr900.dts
Normal file
85
target/linux/ath79/dts/qca9558_engenius_esr900.dts
Normal file
@ -0,0 +1,85 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qca955x_senao_router-dual.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "engenius,esr900", "qca,qca9558";
|
||||
model = "EnGenius ESR900";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_power;
|
||||
led-upgrade = &led_power;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power: power {
|
||||
label = "amber:power";
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
label = "blue:wlan2g";
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
label = "blue:wlan5g";
|
||||
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
|
||||
wps_amber {
|
||||
label = "amber:wps";
|
||||
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wps_blue {
|
||||
label = "blue:wps";
|
||||
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&phy0 {
|
||||
qca,mib-poll-interval = <500>;
|
||||
|
||||
qca,ar8327-initvals = <
|
||||
0x04 0x07680000 /* PORT0 PAD MODE CTRL */
|
||||
0x10 0x40000000 /* POWER_ON_STRAP */
|
||||
0x50 0xcf35cf35 /* LED_CTRL0 */
|
||||
0x54 0xcf35cf35 /* LED_CTRL1 */
|
||||
0x58 0xcf35cf35 /* LED_CTRL2 */
|
||||
0x5c 0x03ffff00 /* LED_CTRL3 */
|
||||
0x7c 0x0000007e /* PORT0_STATUS */
|
||||
>;
|
||||
};
|
||||
|
||||
&usb_phy1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wmac {
|
||||
nvmem-cells = <&calibration_art_1000>;
|
||||
nvmem-cell-names = "calibration";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
|
||||
wifi@0,0,0 {
|
||||
compatible = "pci168c,0033";
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
nvmem-cells = <&calibration_art_5000>;
|
||||
nvmem-cell-names = "calibration";
|
||||
};
|
||||
};
|
||||
@ -287,6 +287,7 @@ ath79_setup_interfaces()
|
||||
dlink,dir-842-c3|\
|
||||
dlink,dir-859-a1|\
|
||||
engenius,epg5000|\
|
||||
engenius,esr900|\
|
||||
sitecom,wlr-7100|\
|
||||
tplink,archer-c2-v3|\
|
||||
tplink,tl-wr1043nd-v4|\
|
||||
@ -665,7 +666,8 @@ ath79_setup_macs()
|
||||
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
|
||||
label_mac=$lan_mac
|
||||
;;
|
||||
engenius,epg5000)
|
||||
engenius,epg5000|\
|
||||
engenius,esr900)
|
||||
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
|
||||
wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
|
||||
;;
|
||||
|
||||
@ -35,6 +35,9 @@ case "$board" in
|
||||
[ "$PHYNBR" -eq 1 ] && \
|
||||
mtd_get_mac_ascii bdcfg "wlanmac" > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
engenius,esr900)
|
||||
macaddr_add "$(mtd_get_mac_ascii u-boot-env ethaddr)" "$PHYNBR" > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
fortinet,fap-221-b)
|
||||
macaddr_add "$(mtd_get_mac_text u-boot 0x3ff80 12)" $((PHYNBR*7+1)) > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
|
||||
@ -12,6 +12,9 @@ preinit_set_mac_address() {
|
||||
ip link set dev eth0 address $(mtd_get_mac_ascii bdcfg "lanmac")
|
||||
ip link set dev eth1 address $(mtd_get_mac_ascii bdcfg "wanmac")
|
||||
;;
|
||||
engenius,esr900)
|
||||
ip link set dev eth0 address $(mtd_get_mac_ascii u-boot-env ethaddr)
|
||||
;;
|
||||
enterasys,ws-ap3705i)
|
||||
ip link set dev eth0 address $(mtd_get_mac_ascii u-boot-env0 ethaddr)
|
||||
;;
|
||||
|
||||
@ -1299,6 +1299,20 @@ define Device/engenius_epg5000
|
||||
endef
|
||||
TARGET_DEVICES += engenius_epg5000
|
||||
|
||||
define Device/engenius_esr900
|
||||
SOC := qca9558
|
||||
DEVICE_VENDOR := EnGenius
|
||||
DEVICE_MODEL := ESR900
|
||||
DEVICE_PACKAGES := kmod-usb2
|
||||
IMAGE_SIZE := 14656k
|
||||
IMAGES += factory.dlf
|
||||
IMAGE/factory.dlf := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
||||
append-rootfs | pad-rootfs | check-size | \
|
||||
senao-header -r 0x101 -p 0x4e -t 2
|
||||
SUPPORTED_DEVICES += esr900
|
||||
endef
|
||||
TARGET_DEVICES += engenius_esr900
|
||||
|
||||
define Device/engenius_ews511ap
|
||||
SOC := qca9531
|
||||
DEVICE_VENDOR := EnGenius
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user