mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-19 13:48:06 +00:00
ar71xx: add support for Teltonika RUT900
Teltonika RUT900 is an industrial 3G router based on Atheros AR9344. There are available 3 other models in RUT9xx series: RUT905, RUT950 and RUT955, which differ in availability of additional I/O ports, built-in GSM modem type, GPS antenna and other features. FCC ID of the RUT950 model (LTE module built-in): 2AET4-RUT950. This patch adds support for the RUT900 model only but can be easily extended to cover whole series. Also, as there are several different 3/4G modules (Huawei, Quectel, Telit) used in whole series, packages required for WWAN support are not included by default. It is up to the user to install required software for built-in modem. Specification: - 550/400/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1 - 2T2R 2,4 GHz (AR9344), with ext. PA (MGA-22103) and LNA - built-in 3G module (example: Telit HE910-D) - 2x miniSIM slot - 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G) - PCA9539 16-bit GPIO I2C expander - 12x LED (4 are driven by AR9344, 7 by PCA9539) - 1x button (reset) - DC jack for main power input (9-30 V) - UART available on PCB edge connector Serial console pinout: - RX: pin1 (square) on top side of the main PCB (AR9344 is on top) - TX: pin1 (square) on bottom side Flash instruction: Vendor firmware is based on OpenWrt CC release. Use the "factory" image directly in GUI (make sure to uncheck "keep settings") or in U-Boot web based recovery. To avoid any problems, make sure to first update vendor firmware to latest version - "factory" image was successfully tested on device running "RUT9XX_R_00.03.960" firmware and U-Boot "3.0.1". Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This commit is contained in:
Piotr Dymacz
parent
b38ff7847b
commit
1f06144cde
@ -595,6 +595,12 @@ re450)
|
||||
ucidef_set_led_wlan "wlan2g" "WLAN 2.4 GHz" "$board:blue:wlan2g" "phy1tpt"
|
||||
ucidef_set_led_wlan "wlan5g" "WLAN 5 GHz" "$board:blue:wlan5g" "phy0tpt"
|
||||
;;
|
||||
rut900)
|
||||
ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth1"
|
||||
ucidef_set_led_switch "lan1" "LAN1" "$board:green:lan1" "switch0" "0x10"
|
||||
ucidef_set_led_switch "lan2" "LAN2" "$board:green:lan2" "switch0" "0x08"
|
||||
ucidef_set_led_switch "lan3" "LAN3" "$board:green:lan3" "switch0" "0x04"
|
||||
;;
|
||||
smart-300)
|
||||
ucidef_set_led_netdev "wan" "WAN" "nc-link:green:wan" "eth0"
|
||||
ucidef_set_led_switch "lan1" "LAN1" "nc-link:green:lan1" "switch0" "0x04"
|
||||
|
||||
@ -428,6 +428,11 @@ ar71xx_setup_interfaces()
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "1:wan" "2:lan"
|
||||
;;
|
||||
rut900)
|
||||
ucidef_set_interfaces_lan_wan "eth0.1" "eth1"
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "2:lan:3" "3:lan:2" "4:lan:1"
|
||||
;;
|
||||
tellstick-znet-lite)
|
||||
ucidef_set_interface_wan "eth0"
|
||||
ucidef_set_interface_raw "wlan" "wlan0" "dhcp"
|
||||
|
||||
@ -40,6 +40,7 @@ get_status_led() {
|
||||
db120|\
|
||||
dr342|\
|
||||
dr344|\
|
||||
rut900|\
|
||||
tew-632brp|\
|
||||
tl-wr942n-v1|\
|
||||
wpj344|\
|
||||
|
||||
@ -995,6 +995,9 @@ ar71xx_board_detect() {
|
||||
*"RouterStation Pro")
|
||||
name="routerstation-pro"
|
||||
;;
|
||||
*"RUT900")
|
||||
name="rut900"
|
||||
;;
|
||||
*"RW2458N")
|
||||
name="rw2458n"
|
||||
;;
|
||||
|
||||
@ -387,6 +387,7 @@ platform_check_image() {
|
||||
onion-omega|\
|
||||
oolite|\
|
||||
re450|\
|
||||
rut900|\
|
||||
smart-300|\
|
||||
som9331|\
|
||||
tellstick-znet-lite|\
|
||||
|
||||
@ -165,6 +165,7 @@ CONFIG_ATH79=y
|
||||
# CONFIG_ATH79_MACH_RBSPI is not set
|
||||
# CONFIG_ATH79_MACH_RBSXTLITE is not set
|
||||
# CONFIG_ATH79_MACH_RE450 is not set
|
||||
# CONFIG_ATH79_MACH_RUT9XX is not set
|
||||
# CONFIG_ATH79_MACH_RW2458N is not set
|
||||
# CONFIG_ATH79_MACH_SC1750 is not set
|
||||
# CONFIG_ATH79_MACH_SC300M is not set
|
||||
|
||||
@ -163,6 +163,7 @@ CONFIG_ATH79=y
|
||||
# CONFIG_ATH79_MACH_RBSPI is not set
|
||||
# CONFIG_ATH79_MACH_RBSXTLITE is not set
|
||||
# CONFIG_ATH79_MACH_RE450 is not set
|
||||
# CONFIG_ATH79_MACH_RUT9XX is not set
|
||||
# CONFIG_ATH79_MACH_RW2458N is not set
|
||||
# CONFIG_ATH79_MACH_SC1750 is not set
|
||||
# CONFIG_ATH79_MACH_SC300M is not set
|
||||
|
||||
@ -1281,6 +1281,17 @@ config ATH79_MACH_RE450
|
||||
select ATH79_DEV_M25P80
|
||||
select ATH79_DEV_WMAC
|
||||
|
||||
config ATH79_MACH_RUT9XX
|
||||
bool "Teltonika RUT900 series support"
|
||||
select SOC_AR934X
|
||||
select ATH79_DEV_ETH
|
||||
select ATH79_DEV_GPIO_BUTTONS
|
||||
select ATH79_DEV_LEDS_GPIO
|
||||
select ATH79_DEV_M25P80
|
||||
select ATH79_DEV_USB
|
||||
select ATH79_DEV_WMAC
|
||||
select GPIO_PCA953X
|
||||
|
||||
config ATH79_MACH_RW2458N
|
||||
bool "Redwave RW2458N board support"
|
||||
select SOC_AR724X
|
||||
|
||||
@ -174,6 +174,7 @@ obj-$(CONFIG_ATH79_MACH_RB95X) += mach-rb95x.o
|
||||
obj-$(CONFIG_ATH79_MACH_RBSPI) += mach-rbspi.o
|
||||
obj-$(CONFIG_ATH79_MACH_RBSXTLITE) += mach-rbsxtlite.o
|
||||
obj-$(CONFIG_ATH79_MACH_RE450) += mach-re450.o
|
||||
obj-$(CONFIG_ATH79_MACH_RUT9XX) += mach-rut9xx.o
|
||||
obj-$(CONFIG_ATH79_MACH_RW2458N) += mach-rw2458n.o
|
||||
obj-$(CONFIG_ATH79_MACH_SC1750) += mach-sc1750.o
|
||||
obj-$(CONFIG_ATH79_MACH_SC300M) += mach-sc300m.o
|
||||
|
||||
191
target/linux/ar71xx/files/arch/mips/ath79/mach-rut9xx.c
Normal file
191
target/linux/ar71xx/files/arch/mips/ath79/mach-rut9xx.c
Normal file
@ -0,0 +1,191 @@
|
||||
/*
|
||||
* Teltonika RUT900 series boards support
|
||||
*
|
||||
* Copyright (C) 2018 Piotr Dymacz <pepe2k@gmail.com>
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify it
|
||||
* under the terms of the GNU General Public License version 2 as published
|
||||
* by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
#include <linux/gpio.h>
|
||||
#include <linux/i2c.h>
|
||||
#include <linux/i2c-algo-bit.h>
|
||||
#include <linux/i2c-gpio.h>
|
||||
#include <linux/platform_data/pca953x.h>
|
||||
#include <linux/platform_device.h>
|
||||
|
||||
#include <asm/mach-ath79/ath79.h>
|
||||
#include <asm/mach-ath79/ar71xx_regs.h>
|
||||
|
||||
#include "common.h"
|
||||
#include "dev-eth.h"
|
||||
#include "dev-gpio-buttons.h"
|
||||
#include "dev-leds-gpio.h"
|
||||
#include "dev-m25p80.h"
|
||||
#include "dev-usb.h"
|
||||
#include "dev-wmac.h"
|
||||
#include "machtypes.h"
|
||||
|
||||
#define RUT9XX_GPIO_LED_LAN1 14
|
||||
#define RUT9XX_GPIO_LED_LAN2 13
|
||||
#define RUT9XX_GPIO_LED_LAN3 22
|
||||
#define RUT9XX_GPIO_LED_WAN 1
|
||||
|
||||
#define RUT9XX_PCA9539_GPIO_BASE 32
|
||||
#define RUT9XX_PCA9539_GPIO_SIGNAL1 (0 + RUT9XX_PCA9539_GPIO_BASE)
|
||||
#define RUT9XX_PCA9539_GPIO_SIGNAL2 (1 + RUT9XX_PCA9539_GPIO_BASE)
|
||||
#define RUT9XX_PCA9539_GPIO_SIGNAL3 (2 + RUT9XX_PCA9539_GPIO_BASE)
|
||||
#define RUT9XX_PCA9539_GPIO_SIGNAL4 (3 + RUT9XX_PCA9539_GPIO_BASE)
|
||||
#define RUT9XX_PCA9539_GPIO_SIGNAL5 (4 + RUT9XX_PCA9539_GPIO_BASE)
|
||||
#define RUT9XX_PCA9539_GPIO_STATUS_R (5 + RUT9XX_PCA9539_GPIO_BASE)
|
||||
#define RUT9XX_PCA9539_GPIO_STATUS_G (6 + RUT9XX_PCA9539_GPIO_BASE)
|
||||
|
||||
#define RUT9XX_GPIO_BTN_RESET 15
|
||||
|
||||
#define RUT9XX_GPIO_I2C_SCK 16
|
||||
#define RUT9XX_GPIO_I2C_SDA 17
|
||||
|
||||
#define RUT9XX_GPIO_EXT_LNA0 2
|
||||
|
||||
#define RUT9XX_WMAC_CALDATA_OFFSET 0x1000
|
||||
|
||||
#define RUT9XX_KEYS_POLL_INTERVAL 20
|
||||
#define RUT9XX_KEYS_DEBOUNCE_INTERVAL (3 * RUT9XX_KEYS_POLL_INTERVAL)
|
||||
|
||||
static struct gpio_led rut900_leds_gpio[] __initdata = {
|
||||
{
|
||||
.name = "rut900:green:lan1",
|
||||
.gpio = RUT9XX_GPIO_LED_LAN1,
|
||||
.active_low = 1,
|
||||
}, {
|
||||
.name = "rut900:green:lan2",
|
||||
.gpio = RUT9XX_GPIO_LED_LAN2,
|
||||
.active_low = 1,
|
||||
}, {
|
||||
.name = "rut900:green:lan3",
|
||||
.gpio = RUT9XX_GPIO_LED_LAN3,
|
||||
.active_low = 1,
|
||||
}, {
|
||||
.name = "rut900:green:signal1",
|
||||
.gpio = RUT9XX_PCA9539_GPIO_SIGNAL1,
|
||||
.active_low = 0,
|
||||
}, {
|
||||
.name = "rut900:green:signal2",
|
||||
.gpio = RUT9XX_PCA9539_GPIO_SIGNAL2,
|
||||
.active_low = 0,
|
||||
}, {
|
||||
.name = "rut900:green:signal3",
|
||||
.gpio = RUT9XX_PCA9539_GPIO_SIGNAL3,
|
||||
.active_low = 0,
|
||||
}, {
|
||||
.name = "rut900:green:signal4",
|
||||
.gpio = RUT9XX_PCA9539_GPIO_SIGNAL4,
|
||||
.active_low = 0,
|
||||
}, {
|
||||
.name = "rut900:green:signal5",
|
||||
.gpio = RUT9XX_PCA9539_GPIO_SIGNAL5,
|
||||
.active_low = 0,
|
||||
}, {
|
||||
.name = "rut900:green:status",
|
||||
.gpio = RUT9XX_PCA9539_GPIO_STATUS_G,
|
||||
.active_low = 0,
|
||||
}, {
|
||||
.name = "rut900:green:wan",
|
||||
.gpio = RUT9XX_GPIO_LED_WAN,
|
||||
.active_low = 1,
|
||||
}, {
|
||||
.name = "rut900:red:status",
|
||||
.gpio = RUT9XX_PCA9539_GPIO_STATUS_R,
|
||||
.active_low = 0,
|
||||
},
|
||||
};
|
||||
|
||||
static struct gpio_keys_button rut900_gpio_keys[] __initdata = {
|
||||
{
|
||||
.desc = "reset",
|
||||
.type = EV_KEY,
|
||||
.code = KEY_RESTART,
|
||||
.debounce_interval = RUT9XX_KEYS_DEBOUNCE_INTERVAL,
|
||||
.gpio = RUT9XX_GPIO_BTN_RESET,
|
||||
.active_low = 1,
|
||||
},
|
||||
};
|
||||
|
||||
static struct i2c_gpio_platform_data rut900_i2c_gpio_data = {
|
||||
.sda_pin = RUT9XX_GPIO_I2C_SDA,
|
||||
.scl_pin = RUT9XX_GPIO_I2C_SCK,
|
||||
.udelay = 10,
|
||||
};
|
||||
|
||||
static struct platform_device rut900_i2c_device = {
|
||||
.name = "i2c-gpio",
|
||||
.id = 0,
|
||||
.dev = {
|
||||
.platform_data = &rut900_i2c_gpio_data,
|
||||
},
|
||||
};
|
||||
|
||||
static struct pca953x_platform_data rut9xx_pca9539_data = {
|
||||
.gpio_base = RUT9XX_PCA9539_GPIO_BASE,
|
||||
.irq_base = -1,
|
||||
};
|
||||
|
||||
static struct i2c_board_info rut900_i2c_devs[] __initdata = {
|
||||
{
|
||||
I2C_BOARD_INFO("pca9539", 0x74),
|
||||
.platform_data = &rut9xx_pca9539_data,
|
||||
},
|
||||
};
|
||||
|
||||
static void __init rut900_setup(void)
|
||||
{
|
||||
u8 *art = (u8 *) KSEG1ADDR(0x1f030000);
|
||||
u8 *mac = (u8 *) KSEG1ADDR(0x1f020000);
|
||||
u8 wlan_mac[ETH_ALEN];
|
||||
|
||||
ath79_register_m25p80(NULL);
|
||||
|
||||
ath79_register_mdio(1, 0x0);
|
||||
|
||||
ath79_switch_data.phy4_mii_en = 1;
|
||||
ath79_switch_data.phy_poll_mask = 0xf1;
|
||||
|
||||
/* LAN */
|
||||
ath79_eth1_data.duplex = DUPLEX_FULL;
|
||||
ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
|
||||
ath79_init_mac(ath79_eth1_data.mac_addr, mac, 0);
|
||||
ath79_register_eth(1);
|
||||
|
||||
/* WAN */
|
||||
ath79_eth0_data.duplex = DUPLEX_FULL;
|
||||
ath79_eth0_data.mii_bus_dev = &ath79_mdio1_device.dev;
|
||||
ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
|
||||
ath79_eth0_data.phy_mask = BIT(4);
|
||||
ath79_eth0_data.speed = SPEED_100;
|
||||
ath79_init_mac(ath79_eth0_data.mac_addr, mac, 1);
|
||||
ath79_register_eth(0);
|
||||
|
||||
platform_device_register(&rut900_i2c_device);
|
||||
i2c_register_board_info(0, rut900_i2c_devs,
|
||||
ARRAY_SIZE(rut900_i2c_devs));
|
||||
|
||||
/* Disable JTAG (enables GPIO0-3) */
|
||||
ath79_gpio_function_enable(AR934X_GPIO_FUNC_JTAG_DISABLE);
|
||||
|
||||
ath79_register_leds_gpio(-1, ARRAY_SIZE(rut900_leds_gpio),
|
||||
rut900_leds_gpio);
|
||||
|
||||
ath79_register_gpio_keys_polled(-1, RUT9XX_KEYS_POLL_INTERVAL,
|
||||
ARRAY_SIZE(rut900_gpio_keys),
|
||||
rut900_gpio_keys);
|
||||
|
||||
ath79_wmac_set_ext_lna_gpio(0, RUT9XX_GPIO_EXT_LNA0);
|
||||
|
||||
ath79_init_mac(wlan_mac, mac, 2);
|
||||
ath79_register_wmac(art + RUT9XX_WMAC_CALDATA_OFFSET, wlan_mac);
|
||||
|
||||
ath79_register_usb();
|
||||
}
|
||||
|
||||
MIPS_MACHINE(ATH79_MACH_RUT9XX, "RUT900", "Teltonika RUT900", rut900_setup);
|
||||
@ -202,6 +202,7 @@ enum ath79_mach_type {
|
||||
ATH79_MACH_RB_SXTLITE2ND, /* Mikrotik RouterBOARD SXT Lite 2nD */
|
||||
ATH79_MACH_RB_SXTLITE5ND, /* Mikrotik RouterBOARD SXT Lite 5nD */
|
||||
ATH79_MACH_RE450, /* TP-LINK RE450 */
|
||||
ATH79_MACH_RUT9XX, /* Teltonika RUT900 series */
|
||||
ATH79_MACH_RW2458N, /* Redwave RW2458N */
|
||||
ATH79_MACH_SC1750, /* Abicom SC1750 */
|
||||
ATH79_MACH_SC300M, /* Abicom SC300M */
|
||||
|
||||
@ -122,6 +122,7 @@ CONFIG_ATH79_MACH_PQI_AIR_PEN=y
|
||||
CONFIG_ATH79_MACH_QIHOO_C301=y
|
||||
CONFIG_ATH79_MACH_R602N=y
|
||||
CONFIG_ATH79_MACH_RE450=y
|
||||
CONFIG_ATH79_MACH_RUT9XX=y
|
||||
CONFIG_ATH79_MACH_RW2458N=y
|
||||
CONFIG_ATH79_MACH_SC1750=y
|
||||
CONFIG_ATH79_MACH_SC300M=y
|
||||
@ -183,6 +184,8 @@ CONFIG_ATH79_MACH_ZCN_1523H=y
|
||||
CONFIG_ATH79_NVRAM=y
|
||||
CONFIG_ATH79_PCI_ATH9K_FIXUP=y
|
||||
CONFIG_BLK_MQ_PCI=y
|
||||
CONFIG_GPIO_PCA953X=y
|
||||
# CONFIG_GPIO_PCA953X_IRQ is not set
|
||||
CONFIG_HW_HAS_PCI=y
|
||||
# CONFIG_LEDS_WNDR3700_USB is not set
|
||||
CONFIG_MYLOADER=y
|
||||
|
||||
@ -7,6 +7,15 @@ define Build/alfa-network-rootfs-header
|
||||
@mv $@.new $@
|
||||
endef
|
||||
|
||||
define Build/append-md5sum-bin
|
||||
$(STAGING_DIR_HOST)/bin/mkhash md5 $@ | sed 's/../\\\\x&/g' |\
|
||||
xargs echo -ne >> $@
|
||||
endef
|
||||
|
||||
define Build/append-string
|
||||
echo -n $(1) >> $@
|
||||
endef
|
||||
|
||||
define Build/mkbuffaloimg
|
||||
$(STAGING_DIR_HOST)/bin/mkbuffaloimg -B $(BOARDNAME) \
|
||||
-R $$(($(subst k, * 1024,$(ROOTFS_SIZE)))) \
|
||||
@ -68,6 +77,17 @@ define Build/seama-seal
|
||||
$(call Build/seama,-s $@.seama $(1))
|
||||
endef
|
||||
|
||||
define Build/teltonika-fw-fake-checksum
|
||||
# Teltonika U-Boot web based firmware upgrade/recovery routine compares
|
||||
# 16 bytes from md5sum1[16] field in TP-Link v1 header (offset: 76 bytes
|
||||
# from begin of the firmware file) with 16 bytes stored just before
|
||||
# 0xdeadc0de marker. Values are only compared, MD5 sum is not verified.
|
||||
let \
|
||||
offs="$$(stat -c%s $@) - 20"; \
|
||||
dd if=$@ bs=1 count=16 skip=76 |\
|
||||
dd of=$@ bs=1 count=16 seek=$$offs conv=notrunc
|
||||
endef
|
||||
|
||||
define Build/uImageHiWiFi
|
||||
# Field ih_name needs to start with "tw150v1"
|
||||
mkimage -A $(LINUX_KARCH) \
|
||||
@ -620,6 +640,28 @@ define Device/r602n
|
||||
endef
|
||||
TARGET_DEVICES += r602n
|
||||
|
||||
define Device/rut900
|
||||
DEVICE_TITLE := Teltonika RUT900
|
||||
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 -uboot-envtools
|
||||
BOARDNAME := RUT900
|
||||
SUPPORTED_DEVICES := rut900
|
||||
IMAGE_SIZE := 15552k
|
||||
MTDPARTS := spi0.0:128k(u-boot)ro,64k(config)ro,64k(art)ro,15552k(firmware),576k(event-log)ro
|
||||
TPLINK_HWID := 0x35000001
|
||||
TPLINK_HWREV := 0x1
|
||||
TPLINK_HEADER_VERSION := 1
|
||||
KERNEL := kernel-bin | patch-cmdline | lzma | tplink-v1-header
|
||||
KERNEL_INITRAMFS := kernel-bin | patch-cmdline | lzma | uImage lzma
|
||||
IMAGES := sysupgrade.bin factory.bin
|
||||
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs |\
|
||||
pad-rootfs | teltonika-fw-fake-checksum | append-string master |\
|
||||
append-md5sum-bin | check-size $$$$(IMAGE_SIZE)
|
||||
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) |\
|
||||
append-rootfs | pad-rootfs | append-metadata |\
|
||||
check-size $$$$(IMAGE_SIZE)
|
||||
endef
|
||||
TARGET_DEVICES += rut900
|
||||
|
||||
define Device/mc-mac1200r
|
||||
$(Device/tplink-8mlzma)
|
||||
DEVICE_TITLE := Mercury MAC1200R
|
||||
|
||||
Loading…
Reference in New Issue
Block a user