Netgear R6100 support

Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 43382

target/linux/ar71xx/base-files/etc/diag.sh

@@ -263,6 +263,7 @@ get_status_led() {
 	wzr-hp-g300nh2)
 		status_led="buffalo:red:diag"
 		;;
+	r6100 | \
 	wndap360 | \
 	wndr3700 | \
 	wndr3700v4 | \

target/linux/ar71xx/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom

@@ -38,6 +38,7 @@ board=$(ar71xx_board_name)
 case "$FIRMWARE" in
 "soc_wmac.eeprom")
 	case $board in
+	r6100 | \
 	wndr3700v4 | \
 	wndr4300)
 		ath9k_eeprom_extract "caldata" 4096 2048

target/linux/ar71xx/base-files/etc/uci-defaults/01_leds

@@ -421,6 +421,12 @@ wndr3700)
 	ucidef_set_led_usbdev "usb" "USB" "netgear:green:usb" "1-1"
 	;;
 
+r6100)
+	ucidef_set_led_netdev "wan" "WAN (green)" "netgear:green:wan" "eth0.2"
+	ucidef_set_led_usbdev "usb" "USB" "netgear:blue:usb" "1-1"
+	ucidef_set_led_wlan "wlan" "WLAN" "netgear:blue:wlan" "phy1tpt"
+	;;
+
 wndr3700v4 | \
 wndr4300)
 	ucidef_set_led_netdev "wan" "WAN (green)" "netgear:green:wan" "eth0.2"

target/linux/ar71xx/base-files/etc/uci-defaults/02_network

@@ -201,7 +201,8 @@ tl-wr941nd)
 	ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
 	;;
 
-smart-300 | \
+r6100 |\
+smart-300 |\
 tl-mr3420-v2 |\
 tl-wr841n-v8 |\
 tl-wr842n-v2 |\

target/linux/ar71xx/base-files/lib/ar71xx.sh

@@ -701,6 +701,9 @@ ar71xx_board_detect() {
 	*"WNDR3700/WNDR3800/WNDRMAC")
 		wndr3700_board_detect "$machine"
 		;;
+	*"R6100")
+		name="r6100"
+		;;
 	*"WNDR3700v4")
 		name="wndr3700v4"
 		;;

target/linux/ar71xx/base-files/lib/preinit/05_set_iface_mac_ar71xx

@@ -29,6 +29,12 @@ preinit_set_mac_address() {
 			fetch_mac_from_mtd config lan_mac wan_mac
 			echo 1 > /sys/class/leds/dir-615-c1:green:wancpu/brightness
 			;;
+		r6100)
+			mac_lan=$(mtd_get_mac_binary caldata 0)
+			[ -n "$mac_lan" ] && ifconfig eth1 hw ether "$mac_lan"
+			mac_wan=$(mtd_get_mac_binary caldata 6)
+			[ -n "$mac_wan" ] && ifconfig eth0 hw ether "$mac_wan"
+			;;
 		wrt160nl)
 			fetch_mac_from_mtd nvram lan_hwaddr wan_hwaddr
 			;;

target/linux/ar71xx/base-files/lib/preinit/81_load_ath10k_board_bin

@@ -22,7 +22,17 @@ do_load_ath10k_board_bin() {
 			macaddr_2bin $mac >> /tmp/ath10k-board.bin
 			dd if=/dev/mtdblock4 \
 				bs=1 skip=20492 count=2104 >> /tmp/ath10k-board.bin
+		;;
+		r6100)
+			local mac
+			mac=$(macaddr_add $(cat /sys/class/net/eth1/address) +2)
 
+			dd if=/dev/mtdblock2 \
+				bs=1 skip=20480 count=6 \
+				of=/tmp/ath10k-board.bin
+			macaddr_2bin $mac >> /tmp/ath10k-board.bin
+			dd if=/dev/mtdblock2 \
+				bs=1 skip=20492 count=2104 >> /tmp/ath10k-board.bin
 		;;
 		qihoo-c301)
 			local mac

target/linux/ar71xx/base-files/lib/upgrade/platform.sh

@@ -354,6 +354,7 @@ platform_check_image() {
 		return 0
 		;;
 	nbg6716 | \
+	r6100 | \
 	wndr3700v4 | \
 	wndr4300 )
 		nand_do_platform_check $board $1

target/linux/ar71xx/config-3.14

@@ -76,6 +76,7 @@ CONFIG_ATH79_MACH_PB42=y
 CONFIG_ATH79_MACH_PB44=y
 CONFIG_ATH79_MACH_PB92=y
 CONFIG_ATH79_MACH_QIHOO_C301=y
+CONFIG_ATH79_MACH_R6100=y
 # CONFIG_ATH79_MACH_RB2011 is not set
 # CONFIG_ATH79_MACH_RB4XX is not set
 # CONFIG_ATH79_MACH_RB750 is not set

target/linux/ar71xx/files/arch/mips/ath79/mach-r6100.c

@@ -0,0 +1,146 @@
+/*
+ *  NETGEAR R6100 board support
+ *
+ *  Copyright (C) 2014 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2014 Imre Kaloz <kaloz@openwrt.org>
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ */
+
+#include <linux/pci.h>
+#include <linux/phy.h>
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+#include <linux/ath9k_platform.h>
+#include <linux/platform/ar934x_nfc.h>
+
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#include "common.h"
+#include "dev-ap9x-pci.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-nfc.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+
+#define R6100_GPIO_LED_WLAN		0
+#define R6100_GPIO_LED_USB		11
+#define R6100_GPIO_LED_WAN_GREEN	13
+#define R6100_GPIO_LED_POWER_AMBER	14
+#define R6100_GPIO_LED_WAN_AMBER	15
+#define R6100_GPIO_LED_POWER_GREEN	17
+
+#define R6100_GPIO_BTN_WIRELESS		1
+#define R6100_GPIO_BTN_WPS		3
+#define R6100_GPIO_BTN_RESET		12
+
+#define R6100_GPIO_USB_POWER		16
+
+#define R6100_KEYS_POLL_INTERVAL	20	/* msecs */
+#define R6100_KEYS_DEBOUNCE_INTERVAL	(3 * R6100_KEYS_POLL_INTERVAL)
+
+static struct gpio_led r6100_leds_gpio[] __initdata = {
+	{
+		.name		= "netgear:green:power",
+		.gpio		= R6100_GPIO_LED_POWER_GREEN,
+		.active_low	= 1,
+	},
+	{
+		.name		= "netgear:amber:power",
+		.gpio		= R6100_GPIO_LED_POWER_AMBER,
+		.active_low	= 1,
+	},
+	{
+		.name		= "netgear:green:wan",
+		.gpio		= R6100_GPIO_LED_WAN_GREEN,
+		.active_low	= 1,
+	},
+	{
+		.name		= "netgear:amber:wan",
+		.gpio		= R6100_GPIO_LED_WAN_AMBER,
+		.active_low	= 1,
+	},
+	{
+		.name		= "netgear:blue:usb",
+		.gpio		= R6100_GPIO_LED_USB,
+		.active_low	= 1,
+	},
+	{
+		.name		= "netgear:blue:wlan",
+		.gpio		= R6100_GPIO_LED_WLAN,
+		.active_low	= 1,
+	},
+};
+
+static struct gpio_keys_button r6100_gpio_keys[] __initdata = {
+	{
+		.desc		= "Reset button",
+		.type		= EV_KEY,
+		.code		= KEY_RESTART,
+		.debounce_interval = R6100_KEYS_DEBOUNCE_INTERVAL,
+		.gpio		= R6100_GPIO_BTN_RESET,
+		.active_low	= 0,
+	},
+	{
+		.desc		= "WPS button",
+		.type		= EV_KEY,
+		.code		= KEY_WPS_BUTTON,
+		.debounce_interval = R6100_KEYS_DEBOUNCE_INTERVAL,
+		.gpio		= R6100_GPIO_BTN_WPS,
+		.active_low	= 0,
+	},
+	{
+		.desc		= "RFKILL switch",
+		.type		= EV_SW,
+		.code		= KEY_RFKILL,
+		.debounce_interval = R6100_KEYS_DEBOUNCE_INTERVAL,
+		.gpio		= R6100_GPIO_BTN_WIRELESS,
+		.active_low	= 0,
+	},
+};
+
+static void __init r6100_setup(void)
+{
+	ath79_register_leds_gpio(-1, ARRAY_SIZE(r6100_leds_gpio),
+				 r6100_leds_gpio);
+	ath79_register_gpio_keys_polled(-1, R6100_KEYS_POLL_INTERVAL,
+					ARRAY_SIZE(r6100_gpio_keys),
+					r6100_gpio_keys);
+
+	ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_SW_PHY_SWAP);
+
+	ath79_register_mdio(1, 0x0);
+
+	/* GMAC0 is connected to the PHY0 of the internal switch */
+	ath79_switch_data.phy4_mii_en = 1;
+	ath79_switch_data.phy_poll_mask = BIT(0);
+	ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
+	ath79_eth0_data.phy_mask = BIT(0);
+	ath79_eth0_data.mii_bus_dev = &ath79_mdio1_device.dev;
+	ath79_register_eth(0);
+
+	/* GMAC1 is connected to the internal switch */
+	ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
+	ath79_register_eth(1);
+
+	gpio_request_one(R6100_GPIO_USB_POWER,
+			 GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED,
+			 "USB power");
+
+	ath79_nfc_set_ecc_mode(AR934X_NFC_ECC_HW);
+	ath79_register_nfc();
+
+	ath79_register_usb();
+
+	ath79_register_wmac_simple();
+
+	ap91_pci_init_simple();
+}
+
+MIPS_MACHINE(ATH79_MACH_R6100, "R6100", "NETGEAR R6100",
+	     r6100_setup);

target/linux/ar71xx/image/Makefile

@@ -301,6 +301,7 @@ wnr2000v3_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,3712k(firmw
 wnr2000v4_mtdlayout=mtdparts=spi0.0:192k(u-boot)ro,64k(u-boot-env)ro,3776k(firmware),64k(art)ro
 wndr3700_mtdlayout=mtdparts=spi0.0:320k(u-boot)ro,128k(u-boot-env)ro,7680k(firmware),64k(art)ro
 wndr3700v2_mtdlayout=mtdparts=spi0.0:320k(u-boot)ro,128k(u-boot-env)ro,15872k(firmware),64k(art)ro
+r6100_mtdlayout=mtdparts=ar934x-nfc:128k(u-boot)ro,256k(caldata),256k(caldata-backup),512k(config),512k(pot),2048k(kernel),122240k(ubi),25600k@0x1a0000(firmware),2048k(language),3072k(traffic_meter)
 wndr4300_mtdlayout=mtdparts=ar934x-nfc:256k(u-boot)ro,256k(u-boot-env)ro,256k(caldata),512k(pot),2048k(language),512k(config),3072k(traffic_meter),2048k(kernel),23552k(ubi),25600k@0x6c0000(firmware),256k(caldata_backup),-(reserved)
 zcn1523h_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,6208k(rootfs),1472k(kernel),64k(configure)ro,64k(mfg)ro,64k(art)ro,7680k@0x50000(firmware)
 mynet_n600_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,64k(devdata)ro,64k(devconf)ro,15872k(firmware),64k(radiocfg)ro
@@ -1343,6 +1344,7 @@ endif # ifeq ($(SUBTARGET),generic)
 ifeq ($(SUBTARGET),nand)
 $(eval $(call SingleProfile,NetgearNAND,64k,WNDR3700V4,wndr3700v4,WNDR3700_V4,ttyS0,115200,$$(wndr4300_mtdlayout),0x33373033,WNDR3700v4,"",-H 29763948+128+128,wndr4300))
 $(eval $(call SingleProfile,NetgearNAND,64k,WNDR4300V1,wndr4300,WNDR4300,ttyS0,115200,$$(wndr4300_mtdlayout),0x33373033,WNDR4300,"",-H 29763948+0+128+128+2x2+3x3,wndr4300))
+$(eval $(call SingleProfile,NetgearNAND,64k,R6100,r6100,R6100,ttyS0,115200,$$(r6100_mtdlayout),0x36303030,R6100,"",-H 29764434+0+128+128+2x2+2x2,wndr4300))
 
 $(eval $(call SingleProfile,ZyXELNAND,128k,NBG6716,nbg6716,NBG6716,ttyS0,115200,NBG6716,$$(zyx_nbg6716_mtdlayout),mem=256M))
 

target/linux/ar71xx/nand/profiles/netgear.mk

@@ -1,10 +1,22 @@
 #
-# Copyright (C) 2009-2013 OpenWrt.org
+# Copyright (C) 2009-2014 OpenWrt.org
 #
 # This is free software, licensed under the GNU General Public License v2.
 # See /LICENSE for more information.
 #
 
+define Profile/R6100
+	NAME:=NETGEAR R6100
+	PACKAGES:=kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-ledtrig-usbdev
+endef
+
+define Profile/R6100/Description
+	Package set optimized for the NETGEAR R6100
+endef
+
+$(eval $(call Profile,R6100))
+
+
 define Profile/WNDR4300
 	NAME:=NETGEAR WNDR3700v4/WNDR4300
 	PACKAGES:=kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-ledtrig-usbdev
@@ -15,5 +27,3 @@ define Profile/WNDR4300/Description
 endef
 
 $(eval $(call Profile,WNDR4300))
-
-

target/linux/ar71xx/patches-3.14/732-MIPS-ath79-add-R6100-support.patch

@@ -0,0 +1,40 @@
+--- a/arch/mips/ath79/Kconfig
++++ b/arch/mips/ath79/Kconfig
+@@ -483,6 +483,17 @@ config ATH79_MACH_WRT400N
+ 	select ATH79_DEV_LEDS_GPIO
+ 	select ATH79_DEV_M25P80
+ 
++config ATH79_MACH_R6100
++	bool "NETGEAR R6100 board support"
++	select SOC_AR934X
++	select ATH79_DEV_AP9X_PCI if PCI
++	select ATH79_DEV_ETH
++	select ATH79_DEV_GPIO_BUTTONS
++	select ATH79_DEV_LEDS_GPIO
++	select ATH79_DEV_NFC
++	select ATH79_DEV_USB
++	select ATH79_DEV_WMAC
++
+ config ATH79_MACH_RB4XX
+ 	bool "MikroTik RouterBOARD 4xx series support"
+ 	select SOC_AR71XX
+--- a/arch/mips/ath79/Makefile
++++ b/arch/mips/ath79/Makefile
+@@ -88,6 +88,7 @@ obj-$(CONFIG_ATH79_MACH_PB42)		+= mach-p
+ obj-$(CONFIG_ATH79_MACH_PB44)		+= mach-pb44.o
+ obj-$(CONFIG_ATH79_MACH_PB92)		+= mach-pb92.o
+ obj-$(CONFIG_ATH79_MACH_QIHOO_C301)	+= mach-qihoo-c301.o
++obj-$(CONFIG_ATH79_MACH_R6100)		+= mach-r6100.o
+ obj-$(CONFIG_ATH79_MACH_RB4XX)		+= mach-rb4xx.o
+ obj-$(CONFIG_ATH79_MACH_RB750)		+= mach-rb750.o
+ obj-$(CONFIG_ATH79_MACH_RB91X)		+= mach-rb91x.o
+--- a/arch/mips/ath79/machtypes.h
++++ b/arch/mips/ath79/machtypes.h
+@@ -84,6 +84,7 @@ enum ath79_mach_type {
+ 	ATH79_MACH_PB42,		/* Atheros PB42 */
+ 	ATH79_MACH_PB92,		/* Atheros PB92 */
+ 	ATH79_MACH_QIHOO_C301,		/* Qihoo 360 C301 */
++	ATH79_MACH_R6100,		/* NETGEAR R6100 */
+ 	ATH79_MACH_RB_411,		/* MikroTik RouterBOARD 411/411A/411AH */
+ 	ATH79_MACH_RB_411U,		/* MikroTik RouterBOARD 411U */
+ 	ATH79_MACH_RB_433,		/* MikroTik RouterBOARD 433/433AH */