mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-21 06:33:41 +00:00
bmips: add support for Netgear EVG2000
The Netgear EVG2000 is a wifi gigabit router, 2.4 GHz single band with
two internal antennas integrated in the main PCB.
Hardware:
- SoC: Broadcom BCM6369
- CPU: dual core BMIPS4350 V3.1 @400Mhz
- RAM: 64 MB DDR
- Flash: 16 MB parallel NOR
- LAN switch: Broadcom BCM53115, 5x 1Gbit
- Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn
- USB: 2x 2.0
- Buttons: 2x, 1 reset
- LEDs: 10x
- FXS: 2x
- UART: yes
Installation via CFE web UI:
1. Power off the router and make a temporal TX-RX shortcircuit on the
serial pins.
2. Power on the router and wait 3 or more seconds
3. Remove the TX-RX shortcircuit
4. Browse to http://192.168.1.1 or http://192.168.0.1 and upload the
firmware
5. Wait a few minutes for it to finish
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
This commit is contained in:
Daniel González Cabanelas
Álvaro Fernández Rojas
parent
df34f71be4
commit
13579e6441
@ -15,6 +15,11 @@ netgear,dgnd3800b)
|
||||
ucidef_set_led_usbport "usb1" "USB1" "green:usb1" "usb1-port1" "usb2-port1"
|
||||
ucidef_set_led_usbport "usb2" "USB2" "green:usb2" "usb1-port2" "usb2-port2"
|
||||
;;
|
||||
netgear,evg2000)
|
||||
ucidef_set_led_netdev "lan" "LAN" "green:lan" "switch.1"
|
||||
ucidef_set_led_netdev "wan" "WAN" "green:wan" "wan"
|
||||
ucidef_set_led_usbdev "usb" "USB" "green:usb" "usb1-port1" "usb2-port1" "usb1-port2" "usb2-port2"
|
||||
;;
|
||||
observa,vh4032n)
|
||||
ucidef_set_led_usbport "usb1" "USB1" "blue:hspa" "usb1-port1" "usb2-port1"
|
||||
ucidef_set_led_usbport "usb2" "USB2" "red:hspa" "1-2-port1" "1-2-port2"
|
||||
|
||||
@ -11,7 +11,8 @@ observa,vh4032n)
|
||||
ucidef_set_interface_lan "lan1 lan2 lan3 lan4"
|
||||
;;
|
||||
netgear,dgnd3700-v1 |\
|
||||
netgear,dgnd3800b)
|
||||
netgear,dgnd3800b |\
|
||||
netgear,evg2000)
|
||||
ucidef_set_bridge_device switch
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
|
||||
;;
|
||||
|
||||
@ -4,6 +4,7 @@
|
||||
|
||||
case "$(board_name)" in
|
||||
comtrend,vr-3025u |\
|
||||
netgear,evg2000 |\
|
||||
observa,vh4032n)
|
||||
mtd fixtrx firmware
|
||||
;;
|
||||
|
||||
237
target/linux/bmips/dts/bcm6369-netgear-evg2000.dts
Normal file
237
target/linux/bmips/dts/bcm6369-netgear-evg2000.dts
Normal file
@ -0,0 +1,237 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later
|
||||
|
||||
#include "bcm6368.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Netgear EVG2000";
|
||||
compatible = "netgear,evg2000", "brcm,bcm6369", "brcm,bcm6368";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power_green;
|
||||
led-failsafe = &led_power_red;
|
||||
led-running = &led_power_green;
|
||||
led-upgrade = &led_power_green;
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys-polled";
|
||||
poll-interval = <100>;
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio 26 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led@2 {
|
||||
label = "green:voip2";
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led@4 {
|
||||
label = "red:internet";
|
||||
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led@5 {
|
||||
label = "green:internet";
|
||||
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led@14 {
|
||||
label = "green:voip1";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led@15 {
|
||||
label = "green:usb";
|
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_power_green: led@22 {
|
||||
label = "green:power";
|
||||
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
led_power_red: led@23 {
|
||||
label = "red:power";
|
||||
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led@24 {
|
||||
label = "green:lan";
|
||||
gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led@27 {
|
||||
label = "green:wan";
|
||||
gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
bcm4322-sprom {
|
||||
compatible = "brcm,ssb-sprom";
|
||||
|
||||
pci-bus = <0>;
|
||||
pci-dev = <1>;
|
||||
|
||||
nvmem-cells = <&macaddr_cfe_6a0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
mac-address-increment = <1>;
|
||||
|
||||
brcm,sprom = "brcm/bcm4322-sprom.bin";
|
||||
brcm,sprom-fixups = <219 0xec08>;
|
||||
};
|
||||
};
|
||||
|
||||
&ehci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ðernet {
|
||||
status = "okay";
|
||||
|
||||
nvmem-cells = <&macaddr_cfe_6a0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&mdio_ext {
|
||||
switch@1e {
|
||||
compatible = "brcm,bcm53115";
|
||||
reg = <30>;
|
||||
|
||||
dsa,member = <1 0>;
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
label = "wan";
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
port@3 {
|
||||
reg = <3>;
|
||||
label = "lan3";
|
||||
};
|
||||
|
||||
port@4 {
|
||||
reg = <4>;
|
||||
label = "lan4";
|
||||
};
|
||||
|
||||
port@8 {
|
||||
reg = <8>;
|
||||
|
||||
phy-mode = "rgmii";
|
||||
ethernet = <&switch0port5>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&switch0 {
|
||||
dsa,member = <0 0>;
|
||||
|
||||
ports {
|
||||
switch0port5: port@5 {
|
||||
reg = <5>;
|
||||
label = "extsw";
|
||||
|
||||
phy-mode = "rgmii";
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pflash {
|
||||
status = "okay";
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
cfe: partition@0 {
|
||||
label = "CFE";
|
||||
reg = <0x000000 0x020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
label = "firmware";
|
||||
reg = <0x020000 0xf40000>;
|
||||
compatible = "brcm,bcm963xx-imagetag";
|
||||
};
|
||||
|
||||
partition@f60000 {
|
||||
label = "board_data";
|
||||
reg = <0xf60000 0x080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@fe0000 {
|
||||
label = "nvram";
|
||||
reg = <0xfe0000 0x020000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&ohci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbh {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cfe {
|
||||
compatible = "nvmem-cells";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_cfe_6a0: macaddr@6a0 {
|
||||
reg = <0x6a0 0x6>;
|
||||
};
|
||||
};
|
||||
@ -43,6 +43,21 @@ define Device/netgear_dgnd3800b
|
||||
endef
|
||||
TARGET_DEVICES += netgear_dgnd3800b
|
||||
|
||||
define Device/netgear_evg2000
|
||||
$(Device/bcm63xx_netgear)
|
||||
DEVICE_MODEL := EVG2000
|
||||
CFE_BOARD_ID := 96369PVG
|
||||
CHIP_ID := 6368
|
||||
SOC := bcm6369
|
||||
BLOCKSIZE := 0x20000
|
||||
NETGEAR_BOARD_ID := U12H154T90_NETGEAR
|
||||
NETGEAR_REGION := 1
|
||||
DEVICE_PACKAGES += $(USB2_PACKAGES) \
|
||||
$(B43_PACKAGES) broadcom-4322-sprom \
|
||||
kmod-leds-gpio
|
||||
endef
|
||||
TARGET_DEVICES += netgear_evg2000
|
||||
|
||||
define Device/observa_vh4032n
|
||||
$(Device/bcm63xx-cfe)
|
||||
DEVICE_VENDOR := Observa
|
||||
|
||||
Loading…
Reference in New Issue
Block a user