layerscape: add Traverse LS1043-S support

The Traverse LS1043-S board is a router board based on
NXP/Freescale's LS1043 SoC, with 4x1GBase-T, 1 SFP and 1 SFP+,
as well as miniPCIe and M.2 LTE.

Unlike the Layerscape reference boards, the LS1043-S board has
NAND flash and uses the mainline U-Boot.

This patch implements support for the LS1043-S board, as well as
the earlier LS1043-V board. It is our intention that all boards
in this family (LS1043-S and later, Five64) will boot the same binary.

Not included in this patchset are the hwmon drivers not in the kernel
(emc1704,pac1934) or the bootloader.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
This commit is contained in:
Mathew McBride 2018-04-30 22:42:39 +10:00 committed by John Crispin
parent 481f870a02
commit 08714738d2
11 changed files with 925 additions and 8 deletions

View File

@ -0,0 +1,25 @@
#!/bin/sh
#
# Copyright (C) 2015 OpenWrt.org
#
. /lib/functions/uci-defaults.sh
board_config_update
board=$(board_name)
case "$board" in
traverse,ls1043v)
ucidef_set_led_netdev "wan" "WAN LED" "ls1043v:yellow:wan" "eth4"
;;
traverse,ls1043s)
ucidef_set_led_netdev "wan" "WAN LED" "ls1043s:yellow:wan" "eth4"
ucidef_set_led_netdev "xgact" "10G Activity" "ls1043s:yellow:10gact" "eth6"
ucidef_set_led_netdev "xglink" "10G Link" "ls1043s:green:10glink" "eth6"
;;
esac
board_config_flush
exit 0

View File

@ -0,0 +1,21 @@
#!/bin/sh
. /lib/functions/system.sh
. /lib/functions/uci-defaults.sh
board_config_update
case "$(board_name)" in
traverse,ls1043v)
ucidef_set_interface_lan "eth0 eth1 eth2 eth3"
ucidef_set_interface_wan "eth4"
;;
traverse,ls1043s)
ucidef_set_interface_lan "eth0 eth1 eth2 eth3 eth6"
ucidef_set_interface_wan "eth4"
;;
esac
board_config_flush
exit 0

View File

@ -0,0 +1,28 @@
#!/bin/sh
#
# Copyright (C) 2015 OpenWrt.org
#
. /lib/functions/uci-defaults.sh
board_config_update
board=$(board_name)
case "$board" in
traverse,ls1043v)
ucidef_add_gpio_switch "lte_reset" "LTE Reset" "377"
ucidef_add_gpio_switch "lte_disable" "LTE Airplane mode" "378"
;;
traverse,ls1043s)
ucidef_add_gpio_switch "tensfp_txdisable" "SFP+ TX Disable" "378"
ucidef_add_gpio_switch "gigsfp_txdisable" "SFP TX Disable" "381"
ucidef_add_gpio_switch "lte_reset" "LTE Reset" "502"
ucidef_add_gpio_switch "lte_disable" "LTE Airplane Mode" "394"
ucidef_add_gpio_switch "lte_power" "LTE Power" "395"
;;
esac
board_config_flush
exit 0

View File

@ -0,0 +1,28 @@
#!/bin/sh
reorder_layerscape_interfaces() {
if [ ! -f /tmp/sysinfo/board_name ]; then
echo "No board name found, not doing reorder_layerscape_interfaces"
return 0
fi
board=$(cat /tmp/sysinfo/board_name)
case "$board" in
"traverse,ls1043v" | \
"traverse,ls1043s")
# Reorder ethernet interfaces to match the physical order
ip link set eth2 name fm1-mac3
ip link set eth4 name eth2
ip link set eth3 name fm1-mac4
ip link set eth5 name eth3
ip link set fm1-mac3 name eth4
ip link set fm1-mac4 name eth5
;;
default)
echo "Unknown board $board"
;;
esac
}
boot_hook_add preinit_main reorder_layerscape_interfaces

View File

@ -0,0 +1,94 @@
#!/bin/sh
#
# Copyright 2015-2018 Traverse Technologies
#
platform_do_upgrade_traverse_nandubi() {
bootsys=$(fw_printenv bootsys | awk -F= '{{print $2}}')
newbootsys=2
if [ "$bootsys" -eq "2" ]; then
newbootsys=1
fi
mkdir -p /tmp/image
cd /tmp/image
get_image "$1" > image.tar
ls -la image.tar
files=$(tar -tf image.tar)
echo "Files in image:"
echo $files
for f in $files
do
part_name=$(echo $f | awk -F '/' '{{print $2}}')
if [ -z "$part_name" ] || [ "$part_name" = "CONTROL" ]; then
continue
fi
[ "$part_name" = "root" ] && part_name="rootfs"
volume=$part_name
if [ "$part_name" = "kernel" ] || [ "$part_name" = "rootfs" ]; then
volume="${part_name}${newbootsys}"
fi
volume_id=$(ubinfo -d 0 --name $volume | awk '/Volume ID/ {print $3}')
file_size=$(tar -tvf image.tar $f | awk '{{print $3}}')
echo "$f size $file_size"
tar -xOf image.tar $f | ubiupdatevol -s $file_size /dev/ubi0_$volume_id -
echo "$volume upgraded"
done
fw_setenv bootsys $newbootsys
echo "Upgrade complete"
}
platform_copy_config() {
bootsys=$(fw_printenv bootsys | awk -F= '{{print $2}}')
rootvol=rootfs$bootsys
volume_id=$(ubinfo -d 0 --name $rootvol | awk '/Volume ID/ {print $3}')
mkdir -p /mnt/oldsys
mount -t ubifs -o rw,noatime /dev/ubi0_$volume_id /mnt/oldsys
cp -af "$CONF_TAR" /mnt/oldsys
umount /mnt/oldsys
}
platform_check_image() {
local board=$(board_name)
case "$board" in
traverse,ls1043v | \
traverse,ls1043s | \
traverse,five64)
local tar_file="$1"
local kernel_length=$( (tar xf $tar_file sysupgrade-traverse-five64/kernel -O | wc -c) 2> /dev/null)
local rootfs_length=$( (tar xf $tar_file sysupgrade-traverse-five64/root -O | wc -c) 2> /dev/null)
[ "$kernel_length" -eq 0 -o "$rootfs_length" -eq 0 ] && {
echo "The upgrade image is corrupt."
return 1
}
return 0
;;
*)
echo "Sysupgrade is not currently supported on $board"
;;
esac
return 1
}
platform_do_upgrade() {
local board=$(board_name)
case "$board" in
traverse,ls1043v | \
traverse,ls1043s | \
traverse,five64)
platform_do_upgrade_traverse_nandubi "$ARGV"
;;
*)
echo "Sysupgrade is not currently supported on $board"
;;
esac
}
platform_pre_upgrade() {
# Force the creation of fw_printenv.lock
mkdir -p /var/lock
touch /var/lock/fw_printenv.lock
export RAMFS_COPY_BIN="/usr/sbin/fw_printenv /usr/sbin/fw_setenv /usr/sbin/ubinfo /bin/echo ${RAMFS_COPY_BIN}"
export RAMFS_COPY_DATA="/etc/fw_env.config /var/lock/fw_printenv.lock ${RAMFS_COPY_DATA}"
}

View File

@ -0,0 +1,332 @@
/*
* Device Tree Include file for Traverse LS1043S board.
*
* Copyright 2014-2015, Freescale Semiconductor
* Copyright 2017-2018, Traverse Technologies
*
* This file is dual-licensed: you can use it either under the terms
* of the GPLv2 or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "fsl-ls1043a.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
model = "Traverse LS1043S";
compatible = "traverse,ls1043s";
aliases {
crypto = &crypto;
ethernet0 = &EMAC0;
ethernet1 = &EMAC1;
ethernet2 = &EMAC2;
ethernet3 = &EMAC3;
ethernet4 = &EMAC4;
ethernet5 = &EMAC5;
};
leds {
compatible = "gpio-leds";
gpio0 {
label = "ls1043s:green:user0";
gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
};
gpio1 {
label = "ls1043s:green:user1";
gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
};
/* LED D17 */
gpio2 {
label = "ls1043s:green:wan";
gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
};
gpio3 {
label = "ls1043s:yellow:wan";
gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
};
/* LED D18 */
gpio4 {
label = "ls1043s:green:mgmt";
gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
};
gpio5 {
label = "ls1043s:yellow:mgmt";
gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
};
/* LED D6 */
gpio6 {
label = "ls1043s:green:user2";
gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
};
/* SFP+ LEDs - these are for chassis
* with lightpipes only
*/
teng_act {
label = "ls1043s:yellow:10gact";
gpios = <&gpio4 0 GPIO_ACTIVE_LOW>;
};
teng_link {
label = "ls1043s:green:10glink";
gpios = <&gpio4 1 GPIO_ACTIVE_LOW>;
};
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <1000>;
/* This button may not be loaded on all boards */
button@0 {
label = "Front button";
linux,code = <KEY_SETUP>;
gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
};
/* This is wired to header S3 */
button@1 {
label = "Rear button";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
};
};
};
&esdhc {
mmc-hs200-1_8v;
sd-uhs-sdr104;
sd-uhs-sdr50;
sd-uhs-sdr25;
sd-uhs-sdr12;
};
&i2c0 {
status = "okay";
rtc@6f {
compatible = "intersil,isl1208";
reg = <0x6f>;
};
sfp_pca9534: pca9534@24 {
compatible = "ti,tca9534", "nxp,pca9534";
gpio-controller;
#gpio-cells = <2>;
reg = <0x24>;
gpio-base = <100>;
};
controller@50 {
compatible = "traverse,controller";
reg = <0x50>;
};
ds125df111@18 {
compatible = "ti,ds125df111";
reg = <0x18>;
};
emc1704@4c {
compatible = "microchip,emc1704";
reg = <0x4c>;
};
pac1934@16 {
compatible = "microchip,pac1934";
reg = <0x16>;
/* Monitoring 3.3V, 5V, Vin/12V (voltage only), Vbat/RTC (voltage only) */
shunt-resistors = <4000 12000 0 0>;
};
pmic@8 {
compatible = "freescale,mc34vr500";
reg = <0x08>;
};
};
/* I2C Bus for SFP EEPROM and control
* These are multiplexed so
* they don't collide when loaded
*/
&i2c3 {
status = "okay";
i2c-switch@70 {
compatible = "nxp,pca9540";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x70>;
gigsfp_i2c: i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
};
tensfp_i2c: i2c@1 {
#address-cells = <1>;
#size-cells = <0>;
reg = <1>;
};
};
};
&ifc {
status = "okay";
#address-cells = <2>;
#size-cells = <1>;
/* Only NAND flash is used on this board */
ranges = <0x0 0x0 0x0 0x7e800000 0x00010000>;
nand@1,0 {
compatible = "fsl,ifc-nand";
#address-cells = <1>;
#size-cells = <1>;
reg = <0x0 0x0 0x10000>;
};
};
&duart0 {
status = "okay";
};
&duart1 {
status = "okay";
};
#include "fsl-ls1043-post.dtsi"
&fman0 {
EMAC0: ethernet@e0000 {
phy-handle = <&qsgmii_phy1>;
phy-connection-type = "qsgmii";
local-mac-address = [0A 00 00 00 00 01];
};
EMAC1: ethernet@e2000 {
phy-handle = <&qsgmii_phy2>;
phy-connection-type = "qsgmii";
local-mac-address = [0A 00 00 00 00 02];
};
EMAC2: ethernet@e8000 {
phy-handle = <&qsgmii_phy3>;
phy-connection-type = "qsgmii";
local-mac-address = [0A 00 00 00 00 03];
};
EMAC3: ethernet@ea000 {
phy-handle = <&qsgmii_phy4>;
phy-connection-type = "qsgmii";
local-mac-address = [0A 00 00 00 00 04];
};
/* SFP via AR8031
* We treat this as a fixed-link as the
* AR8031 is hard-configured into
* 1000BASE-X mode
* Should MII control be desired, remove
* fixed-link and add
* phy-handle = <&rgmii_phy1>;
*/
EMAC4: ethernet@e4000 {
phy-connection-type = "rgmii";
local-mac-address = [0A 00 00 00 00 05];
fixed-link {
speed = <1000>;
full-duplex;
};
};
/* Connection to Expansion (M.2) slot
* Future WAN (i.e xDSL) plugin
*/
EMAC5: ethernet@e6000 {
phy-connection-type = "rgmii-id";
local-mac-address = [00 00 00 00 00 06];
fixed-link {
speed = <1000>;
full-duplex;
};
};
/* 10G SFP+ interface
* This can also run at 1.25 and 2.5G with
* the appropriate SerDes protocol setting in RCW
*/
TENSFP: ethernet@f0000 {
status = "okay";
phy-connection-type = "xgmii";
fixed-link {
speed = <10000>;
full-duplex;
};
};
mdio@fc000 {
rgmii_phy1: ethernet-phy@2 {
reg = <0x2>;
};
qsgmii_phy1: ethernet-phy@4 {
reg = <0x4>;
};
qsgmii_phy2: ethernet-phy@5 {
reg = <0x5>;
};
qsgmii_phy3: ethernet-phy@6 {
reg = <0x6>;
};
qsgmii_phy4: ethernet-phy@7 {
reg = <0x7>;
};
};
};
/* No QUICC engine functions on this board -
* pins are used for other functions (GPIO, I2C etc.)
*/
&uqe {
status = "disabled";
};
/* LS1043S does not use the QorIQ AHCI
* controller.
*/
&sata {
status = "disabled";
};

View File

@ -0,0 +1,253 @@
/*
* Device Tree Include file for Traverse LS1043V board.
*
* Copyright 2014-2015, Freescale Semiconductor
* Copyright 2017, Traverse Technologies
*
* This file is dual-licensed: you can use it either under the terms
* of the GPLv2 or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This library is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This library is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "fsl-ls1043a.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
model = "Traverse LS1043V";
compatible = "traverse,ls1043v";
aliases {
crypto = &crypto;
ethernet0 = &EMAC0;
ethernet1 = &EMAC1;
ethernet2 = &EMAC2;
ethernet3 = &EMAC3;
ethernet4 = &EMAC4;
ethernet5 = &EMAC5;
pca9555 = &pca9555;
};
leds {
compatible = "gpio-leds";
gpio0 {
label = "ls1043v:green:user0";
gpios = <&pca9555 0 GPIO_ACTIVE_LOW>;
};
gpio1 {
label = "ls1043v:yellow:user0";
gpios = <&pca9555 1 GPIO_ACTIVE_LOW>;
};
gpio2 {
label = "ls1043v:green:user1";
gpios = <&pca9555 2 GPIO_ACTIVE_LOW>;
};
gpio3 {
label = "ls1043v:yellow:user1";
gpios = <&pca9555 3 GPIO_ACTIVE_LOW>;
};
gpio4 {
label = "ls1043v:green:user2";
gpios = <&pca9555 4 GPIO_ACTIVE_HIGH>;
};
gpio5 {
label = "ls1043v:yellow:wlan";
gpios = <&pca9555 5 GPIO_ACTIVE_HIGH>;
};
gpio6 {
label = "ls1043v:yellow:wan";
gpios = <&pca9555 6 GPIO_ACTIVE_HIGH>;
};
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <1000>;
button@0 {
label = "Front button";
linux,code = <KEY_SETUP>;
gpios = <&pca9555 14 GPIO_ACTIVE_LOW>;
};
button@1 {
label = "Rear button";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&pca9555 15 GPIO_ACTIVE_LOW>;
};
};
};
&i2c0 {
status = "okay";
rtc@6f {
compatible = "intersil,isl1208";
reg = <0x6f>;
};
pca9555: pca9555@20 {
compatible = "nxp,pca9555";
gpio-controller;
#gpio-cells = <2>;
reg = <0x20>;
gpio-base = <0>;
};
/* CPU core temp sensor and VDD (1.0V) sensor */
ltc2990@4c {
compatible = "lltc,ltc2990";
reg = <0x4C>;
lltc,meas-mode = <4 3>;
};
/* 3.3V and 5V monitor (may not be loaded on some SKUs) */
ltc2990@4f {
compatible = "lltc,ltc2990";
reg = <0x4F>;
lltc,meas-mode = <6 3>;
};
};
&ifc {
status = "okay";
#address-cells = <2>;
#size-cells = <1>;
/* Only NAND flash is used on this board */
ranges = <0x0 0x0 0x0 0x7e800000 0x00010000>;
nand@1,0 {
compatible = "fsl,ifc-nand";
#address-cells = <1>;
#size-cells = <1>;
reg = <0x0 0x0 0x10000>;
};
};
&duart0 {
status = "okay";
};
&duart1 {
status = "okay";
};
#include "fsl-ls1043-post.dtsi"
&fman0 {
EMAC0: ethernet@e0000 {
phy-handle = <&qsgmii_phy1>;
phy-connection-type = "qsgmii";
local-mac-address = [0A 00 00 00 00 01];
};
EMAC1: ethernet@e2000 {
phy-handle = <&qsgmii_phy2>;
phy-connection-type = "qsgmii";
local-mac-address = [0A 00 00 00 00 02];
};
EMAC2: ethernet@e8000 {
phy-handle = <&qsgmii_phy3>;
phy-connection-type = "qsgmii";
local-mac-address = [0A 00 00 00 00 03];
};
EMAC3: ethernet@ea000 {
phy-handle = <&qsgmii_phy4>;
phy-connection-type = "qsgmii";
local-mac-address = [0A 00 00 00 00 04];
};
EMAC4: ethernet@e4000 {
phy-handle = <&rgmii_phy1>;
phy-connection-type = "rgmii";
local-mac-address = [0A 00 00 00 00 05];
};
/* Connection to VDSL SoC */
EMAC5: ethernet@e6000 {
phy-connection-type = "rgmii-id";
local-mac-address = [00 00 00 00 00 06];
fixed-link {
speed = <1000>;
full-duplex;
};
};
/* 10G XFI interface - not in use on this platform */
TENSFP: ethernet@f0000 {
status = "disabled";
phy-connection-type = "sgmii";
fixed-link {
/* NB: speed = 1000 and sgmii allows forward compatibility
* with both 1G and 10G, the same is not true
* in the reverse.
*/
speed = <1000>;
full-duplex;
};
};
mdio@fc000 {
rgmii_phy1: ethernet-phy@3 {
reg = <0x3>;
};
qsgmii_phy1: ethernet-phy@4 {
reg = <0x4>;
};
qsgmii_phy2: ethernet-phy@5 {
reg = <0x5>;
};
qsgmii_phy3: ethernet-phy@6 {
reg = <0x6>;
};
qsgmii_phy4: ethernet-phy@7 {
reg = <0x7>;
};
};
};
/* No QUICC engine functions on this board */
&uqe {
status = "disabled";
};
/* No SATA/AHCI on this board */
&sata {
status = "disabled";
};

View File

@ -7,6 +7,8 @@
include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
ITB_BOARDS = traverse-five64
define Build/append-ls-rcw
rm -f $@
dd if=$(STAGING_DIR_IMAGE)/$(1)-rcw.bin >> $@
@ -45,6 +47,16 @@ define Build/append-ls-dtb
dd if=$(DTS_DIR)/$(1).dtb >> $@
endef
define Build/traverse-fit
./mkits-multiple-config.sh -o $@.its -A $(LINUX_KARCH) -v $(LINUX_VERSION) \
-k $@ -a $(KERNEL_LOADADDR) -e $(if $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \
-C gzip -c 1 -c 2 \
-d $(DEVICE_DTS_DIR)/freescale/traverse-ls1043s.dtb -D "Traverse_LS1043S" -n "ls1043s" -a $(FDT_LOADADDR) -c 1 \
-d $(DEVICE_DTS_DIR)/freescale/traverse-ls1043v.dtb -D "Traverse_LS1043V" -n "ls1043v" -a $(FDT_LOADADDR) -c 2
PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new
@mv -f $@.new $@
endef
define Device/Default
PROFILES = Default
FILESYSTEMS := squashfs
@ -62,6 +74,7 @@ ifeq ($(SUBTARGET),armv8_32b)
KERNEL_LOADADDR = 0x80008000
KERNEL_ENTRY_POINT = 0x80008000
endif
FDT_LOADADDR = 0x90000000
endef
define Device/ls1043ardb
@ -182,4 +195,28 @@ endef
TARGET_DEVICES += ls2088ardb
endif
define Device/traverse-five64
KERNEL_NAME := Image
KERNEL_SUFFIX := -kernel.itb
KERNEL_INSTALL := 1
FILESYSTEMS := ubifs
DEVICE_TITLE := Traverse LS1043 Boards (Five64, LS1043S)
DEVICE_PACKAGES += fman-layerscape-ls1043ardb kmod-i2c-core kmod-rtc-isl1208 uboot-envtools \
uboot-traverse-ls1043v uboot-traverse-ls1043v-sdcard \
kmod-hwmon-core kmod-hwmon-ltc2990 kmod-gpio-pca953x kmod-input-gpio-keys-polled \
kmod-i2c-mux-pca954x kmod-hwmon-pac1934 kmod-hwmon-emc17xx
DEVICE_DESCRIPTION = Build images for Traverse LS1043 boards. This generates a single image \
capable of booting on any of the boards in this family.
DEVICE_DTS = freescale/traverse-ls1043s
DEVICE_DTS_DIR = $(LINUX_DIR)/arch/arm64/boot/dts
DEVICE_DTS_CONFIG = ls1043s
KERNEL := kernel-bin | gzip | traverse-fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb $$(FDT_LOADADDR)
KERNEL_INITRAMFS := kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb $$(FDT_LOADADDR)
IMAGES = root sysupgrade.tar
IMAGE/root = append-rootfs
IMAGE/sysupgrade.tar = sysupgrade-tar
UBIFS_OPTS := -m 2048 -e 124KiB -c 4096
endef
TARGET_DEVICES += traverse-five64
$(eval $(call BuildImage))

View File

@ -0,0 +1,89 @@
From c0612164b379ebc8964da6bc6f6ced9736dce488 Mon Sep 17 00:00:00 2001
From: Mathew McBride <matt@traverse.com.au>
Date: Tue, 17 Apr 2018 10:01:03 +1000
Subject: [PATCH] add DTS for Traverse LS1043 Boards
Signed-off-by: Mathew McBride <matt@traverse.com.au>
---
arch/arm64/boot/dts/freescale/Makefile | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
create mode 100644 arch/arm64/boot/dts/freescale/traverse-ls1043v.dts
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -20,7 +20,10 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
-
+
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += traverse-ls1043v.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += traverse-ls1043s.dtb
+
always := $(dtb-y)
subdir-y := $(dts-dirs)
clean-files := *.dtb
--- a/arch/arm64/boot/dts/freescale/traverse-ls1043s.dts
+++ b/arch/arm64/boot/dts/freescale/traverse-ls1043s.dts
@@ -337,3 +337,29 @@
&sata {
status = "disabled";
};
+
+/* Additions for Layerscape SDK (4.4/4.9) Kernel only
+ * These kernels need additional setup for FMan/QMan DMA shared memory
+ */
+
+&bman_fbpr {
+ compatible = "fsl,bman-fbpr";
+ alloc-ranges = <0 0 0x10000 0>;
+};
+&qman_fqd {
+ compatible = "fsl,qman-fqd";
+ alloc-ranges = <0 0 0x10000 0>;
+};
+&qman_pfdr {
+ compatible = "fsl,qman-pfdr";
+ alloc-ranges = <0 0 0x10000 0>;
+};
+
+&soc {
+#include "qoriq-dpaa-eth.dtsi"
+#include "qoriq-fman3-0-6oh.dtsi"
+};
+
+&fman0 {
+ compatible = "fsl,fman", "simple-bus";
+};
--- a/arch/arm64/boot/dts/freescale/traverse-ls1043v.dts
+++ b/arch/arm64/boot/dts/freescale/traverse-ls1043v.dts
@@ -313,3 +313,29 @@
&sata {
status = "disabled";
};
+
+/* Additions for Layerscape SDK (4.4/4.9) Kernel only
+ * These kernels need additional setup for FMan/QMan DMA shared memory
+ */
+
+&bman_fbpr {
+ compatible = "fsl,bman-fbpr";
+ alloc-ranges = <0 0 0x10000 0>;
+};
+&qman_fqd {
+ compatible = "fsl,qman-fqd";
+ alloc-ranges = <0 0 0x10000 0>;
+};
+&qman_pfdr {
+ compatible = "fsl,qman-pfdr";
+ alloc-ranges = <0 0 0x10000 0>;
+};
+
+&soc {
+#include "qoriq-dpaa-eth.dtsi"
+#include "qoriq-fman3-0-6oh.dtsi"
+};
+
+&fman0 {
+ compatible = "fsl,fman", "simple-bus";
+};

View File

@ -5,8 +5,8 @@ Subject: [PATCH] Recognize when an RGMII Link is set as fixed (in the device
tree) and set up the MAC accordingly
---
drivers/net/ethernet/freescale/sdk_dpaa/mac.c | 1 +
.../ethernet/freescale/sdk_fman/Peripherals/FM/MAC/memac.c | 13 +++++++++++++
drivers/net/ethernet/freescale/sdk_dpaa/mac.c | 1
drivers/net/ethernet/freescale/sdk_fman/Peripherals/FM/MAC/memac.c | 13 ++++++++++
2 files changed, 14 insertions(+)
--- a/drivers/net/ethernet/freescale/sdk_dpaa/mac.c
@ -52,7 +52,7 @@ Subject: [PATCH] Recognize when an RGMII Link is set as fixed (in the device
+ if (ENET_INTERFACE_FROM_MODE(p_Memac->enetMode) == e_ENET_IF_RGMII) {
+ if (mac_dev->fixed_link) {
+ printk("This is a fixed-link, forcing speed %d duplex %d\n",mac_dev->fixed_link->speed,mac_dev->fixed_link->duplex);
+ printk(KERN_INFO "This is a fixed-link, forcing speed %d duplex %d\n",mac_dev->fixed_link->speed,mac_dev->fixed_link->duplex);
+ MemacAdjustLink(h_Memac,mac_dev->fixed_link->speed,mac_dev->fixed_link->duplex);
+ }
+ }

View File

@ -0,0 +1,10 @@
--- a/drivers/mmc/host/sdhci-of-esdhc.c
+++ b/drivers/mmc/host/sdhci-of-esdhc.c
@@ -619,6 +619,7 @@ static void esdhc_reset(struct sdhci_hos
static const struct of_device_id scfg_device_ids[] = {
{ .compatible = "fsl,t1040-scfg", },
{ .compatible = "fsl,ls1012a-scfg", },
+ { .compatible = "fsl,ls1043a-scfg", },
{ .compatible = "fsl,ls1046a-scfg", },
{}
};